Search Documents

By Hinde J. S

The Fitzpatrick Orebody is a three and a half million tonne fault bounded portion of the early-middle Proterozoic Broken Hill Orebody.The Fitzpatrick Orebody was discovered in 1975 by diamond drilling from the 36 Level Exploratory Drive. This followed persistent geologically oriented exploration and a courageous decision by mine management to deepen No. 3 Shaft to provide exploratory development across the Globe Vauxhall Shear and allow effective drilling of the target area.The stratiforrn oebody consists of three lenses, the lead rich No. 2 and 3 Lenses and smaller zinc lode. They represent a down plunge extension and boudinaged, fault-bounded portion of the main Broken Hill ore lenses. The surrounding host rocks are extensively faulted and jointed due to complex history of movement on the bounding shears. This results in extremely poor ground conditions during mining. The ore was delineated for mining development using three dimensional fan drilling from exploratory and hanging wall drive drill sites.

Jan 1, 1990

By Reichardt Y

Fine feed fractions in the size range from 1 to 40 ¦m of materials with different hardness as limestone and silicon carbide have been stressed in two different devices. A tungsten-carbide-blodc allows a single stressing with a pressure up to 2000 MPa and a 4-piston-block enables a multiple stressing procedure in which the material bed is stressed in alternating directions with a pressure up to 700 MPa. The experiments show energy absorption as the major factor for the interparticle breakage of hard material, like quartz, zircon silicate, silicon carbide and smelted oonindum, pressure, however, does not influence the results within the investigated range from 100 to 700 MPa and even up to 2000 MPa for corundum. But the breakage of the middle-hard limestone depends on the pressure so far as more fineness can be produced if the same energy is introduced at a lower pressure level. The creation of very fine and microfine fragments decreases strongly with increasing hardness of the feed materiaL The energy consumption for producing microfine material with a multiple stressing procedure on a particle bed is much lower than that one of a usual milling process. But this procedure needs a classification with a seperation cut at a couple of microns, which is not easy to accomplish.

Jan 1, 1993

Since the discovery of coal of the Southern coalfield (Illawarra 1797, Burragorang 1806) coal mining has grown progressively to the thriving industry of today. Early shallow escarpment mining required no serious access development, but with extension of mining to further and deeper areas, sinking became necess- ary. Now, with 17 major shafts and 7 decline drifts in current use, new mining activities involve several current sinking and drifting projects, with more in prospect. Conventional sinking and drifting, using blasting and mucking techniques proven in recent years are normally in use, with attempts, recent and current to accelerate advances by boring techniques. With export and to less extent local market unpredictability, it is vital to produce mine establishment times to allow advantage to be taken of market upswings and there is great need for research and improvement of mine access construction as the major aspect of establish- ment.

Jan 1, 1976

By J Ledgerwood

Namakwa Sands is a mineral processing company based on the West Coast of South Africa and is solely owned by Exxaro Resources Limited. Mineral ore is mined and processed, concentrated and both chemical and mechanically upgraded before being sent for electrostatic and magnetic separation units. The final high value mineral products report as Zircon, Rutile and Ilmenite.The recovery of non-magnetic material is largely dependent upon a number of factors, including but not limited to dew point, ambient temperature, feed rate, mineral size distribution, specific gravity and mineral content in head feed. One important limiting factor to recovery in typical dry mill operations is the particle size distribution of the feed. Variance in the particle size has catastrophic consequences for recovery. This is the reason for this study. Until recently large variances in non-magnetic production were viewed to be a function of machine operation. This view was later rejected with the feed size distribution determined as the major driver of low recoveries, for Namakwa Sands orebody 50 per cent variance in particle size distribution can be noticed within one day. This is because of the successive mining blending techniques employed.The predicament is that the two modes were so closely placed together that recovery of a single mode is almost impossible without the consequence of greatly reducing recovery. The second mode was found at 125 µm while the first was at 90 µm. Interestingly, for the mentioned feed type a cumulative size distribution of a unimodal feed type is almost exactly the same as for a bimodal size distribution. Thus a plot of cumulative size distribution will show no difference due to the modes being so close together. This is the reason why this phenomenon was not noticed before.The study also found that, using an high tension roll (HTR) or rare earth roll, a fine stream with a single mode at 90 µm versus a coarse stream with a single mode at 150 µm would yield completely different results interms of yields. Larger conductive particles are thrown from the roll while small particles loose charge faster (entrainment). Results in terms of the bimodal size distribution show that even though 25 per cent of the feed type is greater than 150 µm the yields followed a similar pattern to that of the coarse particles rather than that of the majority (75 per cent) fine particles. This confirms what was published by M Ziemski and P N Holtham in 2005 on charge decay rates; they mentioned that particle bed effects played a major role in recovery.

Oct 5, 2011

Since the 1950's drilling has been rapidly mechanised. First from hand held drills with air legs to pneumatic jumbos, then to more effective hydraulic jumbos. Development of underground drilling equipment naturally could not have stopped here. Hydraulic drilling saw an improvement in drilling capacity and efficiency after the introduction of second generation drifters in the early 1980's. Also in the early 1980's a few equipment suppliers started to study how to improve the efficiency in operating the rigs. The first computerised rigs for tunnelling were delivered to work sites in mid 1980's. At the same time a few computerised longhole drills started drilling in mines.

Jan 1, 1988

The reasons for and the methods of inte- gration of the gold treatment plant with the existing nickel concentrator are discussed. The integration was accomplished in three stages commencing in May 1980 and attain- ing current throughput in December 1982. The problems encountered and their solution, including the design and construction of a new tailings dam are also discussed.

Jan 1, 1984

By M Kim, J Park, I-K Suh, E Kim, J Lee

One of the key technologies in developing hydrogen-enriched ironmaking operations is the control of the carburisation, melting, and dripping behaviour of the iron ore burden materials. When a hot compacted iron (HCI) is charged in the blast furnace or the FINEX Melter-Gasifier, iron oxide reduction, the reduced iron’s carburisation, and the melting of iron and slag occur successively. This study investigated the reduction, carburisation, melting and dripping behaviour of HCI under a COH2 gas mixture using the high-temperature X-ray radiographic technique. Under 100 per cent CO gas atmosphere, the dripping temperature was 1410°C. When 5 per cent H2 was introduced, the dripping temperature slightly decreased to 1400°C. Furthermore, the dripping temperature gradually increased as the H2 gas composition increased. As 30 per cent H2 was introduced, the dripping temperature reached 1414°C. The carbon concentration in the drained metal samples gradually increased with increasing H2 composition. It is considered that H2 decreased FeO content in the slag, yielding the increased melting temperature and viscosity of the slag. On the other hand, H2 accelerated the carburisation of the reduced iron by CO gas, enabling the homogenisation of the oxide materials to form a liquid phase. Therefore, it is considered that introducing H2 in the reactor is helpful to increase productivity and energy efficiency by accelerating the liquid phase’s formation.

Aug 21, 2024

By Sharmil Markar M

Ballarat Goldfields Limited is currently re-opening the old workings of the East Ballarat Goldfield which contain an estimated 1800 ML of groundwater. The disposal of this 'minewater' was of concern: the minewater is of moderate salinity; increased salinity levels have interfered with agriculture and water use at a number of locations downstream from Ballarat. Extensive numerical studies indicated that treated minewater could be discharged into the Ballarat Creek system for dilution by sewage effluent and by surface runoff after rainfall events. An automatic real-time salinity management system has been developed to enable the disposal of saline minewater in this fashion. A desk top computer operates the system: discharge and salinity readings are taken automatically each hour and filed away; the maximum allowable rate of discharge of treated minewater is calculated; pumps are switched on and off. The system readily enables daily, weekly and monthly data reports together with floppy disks of 'raw' data to be prepared in formats suitable for direct submission to the Victorian Environmental Protection Authority.

Jan 1, 1990

The pilot scale testing of Australian coals for their NO, emissions was carried out at the ACTC to investigate the influence of coal properties, furnace conditions and different NO,, control strategies on NO,, emissions. The NOx emissions for the Australian coals tested were found to vary over a wide range and primarily depended on combustion temperature and excess oxygen conditions. These coals did not exhibit any fundamental difference in NOx levels to other world coals. Under similar combustion conditions, the conversion of coal nitrogen to NO. was found to be best correlated with coal rank parameter, R, max per centage. The use of staged combustion as a control strategy was shown to reduce their NOx levels by 56 - 77 per cent.

Jan 1, 1991

By H J. Ross, R K. Beatson, T J, W R. Fright

Traditional method of explicitly defining three-dimensional (3D) ore-waste and geological boundaries relies heavily on a time-consuming process of manual digitisation. This method of modelling can be best described as surface modelling, as complex surface geometry is built up by digitising points that lie on the surface. With the advent of fast 3D interpolation methods, however, construction of geological surfaces using volume functions is now a practical alternative to explicit modelling of surfaces. Unlike explicit modelling, surfaces contained in volume functions are not explicitly defined or digitised. Instead the existence of surfaces in the volume function is implicit, thus the process of modelling surfaces from volume function is called æimplicit modellingÆ. Based on recent advances in fast scattered data interpolation methods, implicit modelling first defines a continuous three-dimensional function that describes the grade or rock distribution. This volumetric function is interrogated for a grade value, or a geological surface, thus allowing the extraction of the 3D object to be automated and eliminating the need to manually digitise surfaces. Since the function is continuous throughout space and does not depend on a mesh or grid for its definition, the extracted geological or grade wireframes can be constructed at any desired resolution in the specific volume of interest. The volume modelling method can work on scattered drillhole data of any data density, including processing combined information from dense grade control data as well as sparse resource drilling. It offers distinct advantages over surface modelling, including: being able to wireframe geological objects that may take days to digitise in tens of minutes; substantial improvement in modelling accuracy; and the ability to generate conditional models rapidly allowing mining risks inherent in geological modelling to be examined.

Jan 1, 2003

By Scoble M, Peck J

This paper reviews the instrumentation and monitoring of blasthole drills and electric mining shovels at a surface coal mine in western Canada. The drill monitoring component involved the development and implementation of microprocessor-based hardware on Bucyrus-Erie 45R and 60R drills. Over a two year period 3800 metres of blasthole drilling were monitored The drill data was subsequently correlated with core and geophysical logs towards identifying unique and reproducible ranges of performance parameter data for the different rock types penetrated. Using this technique, the geology of the study area benches was characterized in detail. Once these same benches had been blasted, the performance of a P&H 2800XP shovel was monitored as it worked through the blasted ground. In this regard, the influence of different digging conditions on shovel performance were identified in a range of blast and geological environments within the study area. The precise nature of these environments was confirmed by a correlation with the interpreted drill monitored data and muckpile size distributions obtained from a digital photo-analysis study. The excavation of 500 000 bcm of waste was thus monitored and a digging index derived which reflected variations in muckpile diggability. The paper concludes by proposing an integrated monitoring approach which, as a first step, uses interpreted drill data for explosive loading. This capability would permit greater accuracy in explosives loading ie. charge placement within higher strength lithologies, while avoiding weaker units. The performance of an instrumented shovel would then be monitored as it works through the resulting muckpile. Interpretation of the shovel performance data would determine the overall quality of the blast in terms of a digging index (DI), providing an indication of the relative digging effort and the effectiveness of the blast design.

Jan 1, 1990

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

By J F. C L Costa, J C. Koppe, C Diedrich

Currently mineral resources evaluation is firstly expressed in terms of volume. Next the resources are transformed into tonnes by using an average bulk density applied to the whole deposit or, in some other circumstances, various different densities to distinct geological domains. Previous work in uranium, copper and nickel deposits used linear correlation between grades and bulk density to derive the density. Geophysics methods are also another good way to obtain density indirectly.These approaches do not take into account that two samples with the same grade but with different bulk densities can characterise different sample supports, leading to severe bias in grade and tonne estimates. It is important that the systematic measurements of bulk density are included into the estimation process, particularly when density is not correlated with the grades. Additionally, the extra time and costs involved in obtaining the bulk density data have made the mining industry disregard it.This study reports the impact in resource estimates by using a methodology that includes the bulk density variability. It involves the determination of a variability model for the bulk density and another model for the composite that was weighted by density as well as by its length. Next, these variables are estimated by kriging and the final grade estimates are obtained. The tonnages are obtained with the bulk density estimates. The conventional methodology was also applied and both estimates are compared to the reconciliation data from a major copper deposit. The results show a significant difference between the tonnage and grade estimates obtained from these two methodologies.The results show that considering density variability when compositing leads to a more accurate methodology resulting in better grade and tonnage estimates locally and globally.

Sep 26, 2011

By O A. Aladejebi, S Mitra, T Singh, D J. Pinson, S, S J. Chew, T Honey

Currently, many commercial sinter plants are exploring the potential addition of high-grade iron ore concentrates to improve the sinter grade. A better understanding of the ore blend, granule behaviour and green bed properties is critical to making this change and maintaining productivity in the sinter plant. This study compared the performance of a laboratory scale granulation drum to a commercial scale unit. The blend used was an Asia-Pacific style sinter blend containing iron ore concentrates. The operating conditions of the two granulation drums (laboratory and commercial scale) were fixed at the same Froude Number (0.00337), space factor (15 per cent) and residence time (4.5 mins). The granules were characterised by measuring their mean size, size distribution and green bed voidage. It was found that the laboratory scale granules were representative of commercial sinter plant granules at similar moisture content. When the moisture was fixed at ~6.9 per cent, granulation time had no significant effect. A further fundamental investigation was undertaken to measure the water holding capacity and intra-particle porosity of the individual ores used in this study. The kinetics of water absorption were measured which showed that water absorbs quickly into the ore particles within the first 60 seconds, slowing down until final saturation was attained after six hours. A linear relationship between the water holding capacity and intra-particle porosity was noted for different ore particle sizes. The results of this study provide a baseline understanding of the current commercial sinter blend and encourage exploring the specific effect of increasing the proportion of ultrafine concentrates in sintering in a future study.

Sep 18, 2023

By Beamish B. B

In this study, a systematic examination of the scale and variety of micro-structures in coal using Scanning Electron Microscopy (SEM) has been carried out, using coal samples of differing stages of coalification from the Bowen Basin and New Zealand. SEM provides detail of various micro-structural features and shows that a variety of micron-sized fractures and cavities are present in coals. These are differentiated into three pore types: fracture porosity, phyteral porosity and matrix porosity. Fracture porosity is generally associated with bright coals (although it has been shown that micro-fractures are present in maceral fragments from the dull coal layers). Characteristically the macro- and micro- fractures form a continuous structural fabric through the bright coal layers and thus make a significant contribution to overall permeability. The macro- and micro-fractures appear to have been formed during the process of coalification rather than being formed due to shrinkage during methane extraction, as most of them are infilled with secondary minerals. In contrast, phyteral and matrix porosity is associated with the dull coal layers that are composed of plant fragments or a heterogeneous mixture of macerals. Like the macro- and micro-fractures, the continuity of the observed cavities suggest that these too are a significant contribution to overall permeability, and therefore play a major role in the transmissibility of methane at a level between diffusion at the micropore level and laminar flow at the macro-fracture level. Due to different spacing, orientation and persistence of individual fractures and cavities, the rate of methane transmissibility through a coalseam will vary according to coal rank, coal type and the organic precursors from which the coal was derived. This is important as a knowledge of the micro-structure system and its relationship to coal type and coal rank, plays an important consideration in: a) gas drainage modelling, b) enhancing permeability by inducing fractures and c) predicting the occurrence of outbursts.

Jan 1, 1991

By B Roache, J O’Brien, M Gray

Admixture use in cement products is commonplace in the construction and mining industries. Many Australian mines have an operational concrete batch plant and stock hydration control and water reducing admixtures. The benefits of admixture use, especially in shotcrete is understood and well documented. Cemented rock fill (CRF) is used to fill stope voids and create stable vertical and undercut surfaces at some Australian mines. These mines generally mix rock fill with a slurry of cement and water without the use of admixtures. Recently published work on optimisation of CRF mixes has mainly focused on the strength increases associated with changes to the mix grading proportions by the addition of fines, but not focusing on the potential benefits of admixture use. Admixture use in CRF may be the simplest CRF optimisation method, as the admixtures will often be added by the push of a button at the batch plant. A CRF testing program was undertaken to test the benefits of admixture use in terms of strength gain, using hydration control additives (HCA) and high range water reducer (HRWR) admixtures. Rock fill gradings were strictly controlled in the test process to allow clear definition of the difference admixtures provide in compression at 28 days. The testing results define admixture associated strength gains in a 6 per cent general purpose (GP) cement by dry weight CRF mix (131 kg of cement/m3). Costings have been developed to allow a mine operator to understand the cost benefits of admixture use in CRF due to reduced operating costs. Operational efficiency advances and a suggested admixture implementation plan for CRF optimisation is offered.

Nov 29, 2022

By M Orunesu Preiata

The Odysseus Project is part of the high-grade Cosmos Nickel Complex that lies 30 km north of Leinster. The Odysseus definitive feasibility study (DFS) was approved by the Western Areas’ board in October 2018. Early works commenced in January 2019 with rehabilitation of the existing underground infrastructure. In June 2022 Western Areas was acquired by IGO Ltd. The project is now well advanced to meet its target of first concentrate. The project included the construction of a haulage shaft. The design of the hoisting equipment and the shaft barrel evolved from the initial DFS design stage to the final execution, as the data were made available from the initial investigation to the data gathered during execution (although this did not change from its initial concept). The design philosophy for the haulage shaft incorporated, from the beginning a multidisciplinary approach with inputs from three main areas involved in such projects, namely excavation techniques, geotechnical assessments, and infrastructure construction. This interaction is a fundamental component for the success of such a critical project. In fact, each of these three areas influences each other in a cyclical manner, triggering a continuous review of the project inputs and outputs, while maintaining the original project goals: the design of an infrastructure able to deliver the desired throughput. The throughput dictates the infrastructure that needs to be built, which in turn controls the size of the shaft. The key assumption applied to this is that the rock mass can accommodate the excavation void, and the excavation technique with its tolerances and limits that ultimately need to be verified back with the initial assumptions used for the infrastructure design. The aim of the paper is to present a case study of the experience gained with the Odysseus hoisting shaft and to propose a possible logic path for similar projects elsewhere.

Mar 29, 2023

The Australian Coal Combustion Testing and Research Facility has been operating commercially for one year and during that period coal product evaluations have been conducted on behalf of four coal companies and one electricity commission. The facility is equipped to assess the behaviour of steaming coal in milling, combustion (including flame stability, burnout and heat transfer), ash deposition and erosion, fly ash collection and gaseous emissions. The relevance of the results of the pilot testing to industrial practice was demonstrated during the calibration of the facility using four coals burnt in Australian power stations. The calibration coals were from the Tarong and Gladstone Power Stations in Queensland, tluja Power Station in Western Australia and Bayswater Power Station in New South Wales. Also an opportunity arose to visit an overseas power station to observe a full scale test burn using one of the early coals tested on a commercial basis in the combustion test facility. The calibration trials showed excellent agreement with industrial coal performance in t:orms of flame stability, turndown, carbon burnout and gaseous emissions. Encouraging correlations were also found in the case of furnace radiation, boiler deposits (slagging and fouling) and electrostatic precipitation. In the case of the last group the only real reservations about the correlations are due to the non-availability or qualitative nature of results collected around the power stations. In all cases there is a high degree of confidence in the facility's ability to predict the relative performance of different coals and in some cases direct numerical predictions can be Made.

Jan 1, 1987

Mine planning typically involves designing an operation to uncover coal with the minimum initial costs with reclamation planning and earthworks being done as an "add on" task. The landform is too steep to remain stable, has no drainage and frequently has areas of excessive acidity or alkalinity. Extensive earthworks are required to reduce grades to an acceptable level and create a drainage system. The flexibility available to the mining engineer to alter the post mining landscape clearly depends on the mining methods. Straight dragline stripping provides virtually no flexibility. However most mining operations over the term of current ten year plans have a substantial pre-strip component. It is this pre-strip material which has the potential to reduce the final reshaping earthworks. The reshaping operation itself is subject to some flexibility with various options being available to re-grade and provide drainage. The full utilisation of this flexibility to minimise earthworks cost should be the aim of reclamation design. ACIRL's current thrust in reclamation is aimed at the integration of mine planning and reclamation earthworks. This involves gathering all environment and agricultural criteria and designing the earth works necessary to produce an acceptable final landform. A key component of our work is the use of computer aided design (CADD) for the design of spoil piles, pre-strip dumps and spoil re-shaping. This approach has been applied to a number of mine sites with earthworks operations covering hundreds of hectares and hundreds of millions of cubic metres volume. We are continuing to provide that consultancy service and at the same time are involved in the development of more sophisticated software tools to apply to reclamation design.

Jan 1, 1991

Three separate and unconfined aquifers occur in the Hilton area, named relative to position in relation to ore horizons: Footwall Aquifer in the east; Ore-Zone Aquifer within the ore-bearing Urquhart Shales; and the Hangingwall Aquifer in the west.It is the on-going strategy it Hilton to drain the Ore-Zone Aquifer which occupies structurally- and sulphide-controlled leached zones in the steeply west dipping strata. The aquifer affects considerable ore reserves to 480 m below the surface. Dewatering began in 1976, and is essentially completed to 4 level (240 m below surface). Dewatering efforts are now based on 8 level (480 m below surface).

Jan 1, 1993