Search Documents

By Benjamin C. Koskiniemi

Introduction When evaluating any ore body, one of the first questions concerns the ore reserves. In the case of an open pit mine, this is not possible to answer reliably until the ultimate (final) pit limits have been established. Techniques used in designing an ultimate pit are classed as (1) manual, (2) computer, and (3) combined manual-computer. This chapter will describe how manual techniques can be utilized in designing an ulti¬mate pit Certain economic and design criteria must be established before the actual design begins In order to begin designing an ultimate pit, it will be assumed that the engineer already has the following data available (1) vertical sections, (2) horizontal sections for each level, (3) stripping curve, (4) bench height, (5) bank slope angle between levels, (6) level berm width, (7) roadway width, (8) pit slope angles at ultimate pit limits (estimated average including roads and ramps and between roads and ramps), and (9) minimum width of pit bottom

Jan 1, 1979

By L. H. Lange

It is the author's opinion, based on many field experiences over several years, that it is usually better to design a rougher flotation circuit with long rows of rougher cells for high tonnage capacity for maximum recovery and better operating efficiency than the alternative of a greater number of shorter rows with proportionately less tonnage of feed per row. Recent plant studies and tests in the 12,000 ton per day flotation plant of the Atlas Consolidated Mining and Development Corp., Cebu, P. I., have given further substantial support to this opinion. There are two flotation sections in this concentrator: 1) Section 1, treating half the tonnage to the total mill, has eight rows of rougher cells, each row containing 360 cu ft of cell volume. Accordingly, each row of cells receives, on the average, 750 tons per 24 hours which assays about 0.65 to 0.75% copper. The main copper mineral is chalcopyrite with minor

Jan 11, 1963

By Ingemar Marklund

This presentation deals with the conditions at IKAB’s mine in Malmberget but also pertains to underground mining in general. GEOLOGY The Malnberget iron ore field is of pre-cambrian age. The wallrock consists of leptites, gneisses and granites, most of them being recrystallized acid and inter- mediate volcanics. The ore-field is strongly folded, with the folding axes plunging to the south. The original orebed is divided into about 20 different orebodies with a strong variation in dip and form. The ore is mainly magnetite. About 1046 of the ore area consists of hematite ore. The phosphorous content is in average 0,8% and the ore is rather course grained. Fig 1. BACKGROUND At LKAB1s mine in Malmberget the sub- level caving method is the main method of mining. Experiments with vein-mining and sub-level stoping are also underway. The present system of mining is already strictly tied up in investments and infrastructure involved in the mining. Fig 2.

Jan 1, 1981

President-Mrs Felix E Wormser, 1 Acorn Lane, Larchmont, New Yolk First Vice-President-Mrs Francis Cameron, 10 Edgewood Drive, Summit, New Jersey Second Vice-President-Mrs Lyman H Hart, 67 Essex House, Garthwood Apartments, Scarsdale, New York Third Vice-President-Mrs David Eugene Park, 350 East 57 Street, New York 22, New York Fourth Vice-President-Mrs Harold 0 Bosworth, 415 Lafayette Street, Denver 3, Colorado Fifth Vice-President-Mrs J B Haffner, Box 29, Kellogg, Idaho Recording Secretary-Mrs W McG Peirce, 7 Lexington Avenue, New York 10, New York Asst Recording Secretary-Mrs Arnold H Miller, 601 West 115 Street, New York 25, New York Corresponding Secretary-Mrs Theodore Nagel, 76 Remsen Street, Brooklyn 1, New York Treasurer-Mrs Robert W Rowen, 116 East 68 Street, New York 21, New York Assistant Treasurer-Mrs Samuel Dolbear, 11 Broadway, New York 4, New York Assistant Treasurer-Mrs H A Kursell, 12 Murray Hill Road, Scarsdale, New York

Jan 1, 1954

The next meeting of the Institute, the 113th meeting, will be held in Arizona in the latter part of September, 1916. All papers to be presented, at this meeting must be published in the September Bulletin or previously. Manuscripts must, therefore,' be in the hands of the Secretary of the Institute not later than July 1. In case manuscripts are given by authors to members of technical committees, or others, they must be in the hands of such persons sufficiently in advance so that they may be actually in the hands of the Secretary of the Institute by the date mentioned. In the past, the Secretary has received urgent requests for special consideration regarding manuscripts that come in after the closing date. In view of the obvious unfairness of this, the Committee on Papers and Publications has instructed the Secretary not to accept for presentation at the Arizona Meeting any papers received later than July 1, 1916.

Jan 3, 1916

The State School of Mines, University of Utah, is this year giving-a four weeks' course for prospectors-Jan. 8 to Feb. 3, 1917-covering the fundamentals of geology, mineralogy, mining and the metallurgical treatment of ores. There will be 36 lectures of 1 hr. each and about 20 laboratory periods, each 3 hr. in length. It is the purpose of the School of Mines to make the course entirely a practical one, and purely theoretical considerations will be omitted. The laboratory work is designed to supplement the lectures and-to give those taking the course a working knowledge of the principles involved. In order to bring the course within the reach of all, no laboratory fees will be charged, and the only fee will be a nominal one for registration in the University, of $1.00, but it is expected that those who attend will be genuinely interested in the work.

Jan 2, 1917

By W. Hume-Rothery

RECENT interest has been shown in utilizing solid-state techniques for obtaining large oriented grains in the Alnico Alloys.1-4 Unfortunately, due to the inherent brittleness of these materials it is difficult to introduce sufficient imperfections by deformation to support the nucleation and growth of new, recrystallized grains. As a result, recrystal-lization methods for obtaining large grains, such as the strain-anneal technique, do not appear to be feasible. Steinort et a1.2 used a combination of a thermal gradient and internal strains to obtain large single crystals of Alnico 5 from a poly crystalline casting by annealing at temperatures above 1200°C. It was suggested that the strains were the result of the precipitation of the y phase which exists between -850° and 1200°C. The purpose of the present study was to determine if the grain size of the cast Alnico alloys can be markedly increased by solid state techniques involv-

Jan 1, 1963

J: H. POLHEMUS, New York, N. Y. (written discussion*).-The Joplin .mining and milling practice has largely influenced operating methods in the Wisconsin district. Milling equipment is essentially of the same type with the notable exception that no tables are used. The treatment of the flue 'sands has been attempted several times but without commercial success. Table material coming from any one mill is low both in tonnage and zinc content. The iron is comparatively high as the pyrite-line "chat" is much more prevalent than the zinc-lime attached particle. In the finer sizes the zinc occurs mainly as free mineral. These condi-tions make the production of good-grade table concentrates very diffi-cult. The accompanying tabulated results from several mill tests indi-cate the character of the mill tails. I think the average mill tails in the district assay nearer 1.5 per cent. zinc than under 1 per cent., as stated by Messrs. Boericke and Garnett.

Jan 10, 1919

By Bailey, Lewis Newton

Bailey, Lewis Newton, Master Engineer, Senior Oracle, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia, at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103d Engineers, killed in action near Fismes, Aug. 9, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M. killed in action on October 12, 1917. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service, Jan. 1,, 1918. Hall, William T., Capt., Royal Flying Corps, killed in action, May 19, 1917.

Jan 11, 1918

The next meeting of the Institute, the 113th meeting, will he held in Arizona in the latter part of September, 1916. All papers to be presented at this meeting must be published in the September Bulletin or previously. Manuscripts must, therefore, be in the hands of the Secretary of the Institute not later than July 1. In case manuscripts are given by authors to members of technical committees, or others, they must be in the hands of such persons sufficiently in advance so that they may be actually in the hands of the Secretary of the Institute by the date mentioned. In the past, the Secretary has received urgent requests for special consideration regarding manuscripts that come in after the closing date. In view of the obvious unfairness of this, the Committee on Papers and Publications has instructed the Secretary not to accept for presentation at the Arizona Meeting any papers received later than July 1, 1916.

Jan 4, 1916

By E. T. Turkdogan, J. H. Swisher

bi the fivst part of the paper results ave given on the rate of decarburization of Fe-C melts ln CO2-CO atmospheres at 1580°C. The rate -controlling step is believed to he that irvlloluing dissociation of curbotz dioxide on the suvfuce of the melt. 4 genevral reaction mechanistm is poslnlated jor gels-t11eta1 veactions oc-curit~g on the surface of iron coutcotamncited with chemi-sovbed osygesL. Oxygen the present work on decavbuvization of liquid iron and previous studies on the kinetics of nitrogen absorption and desorplion are discussed in terms of the postulated mechanism, ManY of the early studies of rate of decarburization of liquid steel were of an exploratory nature and laboratory exppriments carried out pertained to open-hearth or oxygen steelmaking processes. References to previous work on this subject may be found in a literature survey made by Ward. Using more sophisticated experimental techniques, several investigators have recently studied the kinetics of decarburization of molten Fe-C alloys in oxygen-bearing gases. For example, Baker et al2.' reported their findings on the rate of decarburization of liquid iron, levitated by an electromagnetic field, in carbon dioxide-carbon monoxide-helium atmospheres. In these levitation experiments the samples used were small in size, e.g., -0.6-cm-diam spheres weighing -0.7 g, and the rates were measured for decarburization from about 5 to 1 pct C at 1660°C. The rates obtained under their experimental conditions were considered to be controlled primarily by gaseous diffusion through the boundary layer at the surface of the levitated melt. Parlee and coworkers3 measured the rate of absorption of carbon monoxide in liquid iron. The rates were found to follow first-order reaction kinetics, yielding a reaction velocity or a mass transfer coefficient in the range 0.2 to 0.4 cm per min. The coefficient was found to decrease with increasing carbon content of the melt. These investigators attributed the observed rates to the transfer of carbon or oxygen through the diffusion boundary layer adjacent to the surface of the melt. In the work to be reported in this paper, an attempt has been made to study the kinetics of gas-metal surface reactions involved in the decarburization of liquid iron. EXPERIMENTAL The experiments consisted of melting 80-g samples from an Fe-1 pct C master alloy in an induction furnace and decarburizing in controlled CO2-CO mixtures at 1 atm pressure and 1580°C. The master alloy was prepared by adding graphite to electrolytic "Plastiron" melted in racuo. None of the impurities in the master alloy exceeded 0.005 pct. The reacting gases were dried by passage through columns of anhydrone; in addition, CO2 impurity in carbon monoxide was removed by passage through a column of ascarite. A schematic diagram of the apparatus is shown in Fig. 1. A 1.25-in.-diam recrys-tallized alumina crucible containing the sample was placed inside a 3-in.-diam quartz reaction tube, all of which was surrounded by an induction coil. A 450-kcps induction generator was used as the power source. Water-cooled brass flanges, which contained the gas inlet, gas exit, and sight port, were sealed to the top of the reaction tube with epoxy resin. The reacting gases were metered with capillary flowmeters and passed through a platinum wire-wound alumina preheating tube, 0.25 in. ID and 11 in. long. The gases were preheated to about 1300°C. A disappearing-filament optical pyrometer was used to measure the melt temperature. The pyrometer was initially calibrated against a Pt-6 pct Rh/Pt-30 pct Rh thermocouple. The temperature was controlled to within +10°C by manually adjusting the power input to the induction coil. In a typical experiment, an 80-g sample of the master alloy was melted in a CO2-CO atmosphere having pcO2/pco = 0.02 and flowing at 1 liter per min. A negligible amount of carbon was lost and no significant reduction of alumina from the crucible occurred during melting, e.g., 0.005 pct Al in the metal. After reaching the experimental temperature of 1580°C, the gas composition was changed to that desired for a particular series of decarburization experiments. The duration of the transient period for obtaining the desired gas composition at the surface of the melt was about 20 sec . The flow rate of the reacting gas was maintained at 1 liter per min. After a predetermined reaction time, the power to the furnace was turned off. During freezing, which took about 10 sec, the amount of gas evolution was not sufficient to result in a significant loss of carbon. The samples were analyzed for carbon by combustion and in a few cases they were analyzed for oxygen by the vacuum-fusion method. RESULTS A marked increase in the rate of decarburization of iron with increasing pcO2/pco ratio in the gas stream is demonstrated by the experimental results given in Figs. 2 and 3 for pco2/pco ratios from 0.033 to 4.0. In one series of experiments, denoted by filled triangles in Fig. 2, the reacting gas was diluted with argon (48 vol pct) resulting in a slower rate of decarburization. Samples from two series of experiments with pco2/pco = 0.033 and pco2/pco = 0.10 (with argon dilufion) were analyzed for oxygen. In these Samples the oxygen content increased with reaction time

Jan 1, 1968

By A. S. Yue, A. E. Vidoz, F. W. Crossman

Tensile specimens were prepared from a single grain of an epitaxially grown Al-CuAl2 eutectic ingot. The eutectic lanzellae were oriented parallel and perpendicular to the tensile axis of the specimens. Since the composite was of the eutectic composition, the aluminum-rich matrix could dissolve up lo 5. 7 wt pct Cu in solid solution and, therefore, was amenable to strengthening by precipitation hardening. The tensile properties of the eutectic single crystals were determined at room temperature as functions of interlamel-lar spacing, platelet orientation, and thermornechanical trealment. The obserced variations in composite stress and modulus with respect to the level of&apos; composite strain are discussed in terms of premature fracture of CuAlz platelets, a distribution function for the strength of the lamellae, and unequal strains due to localized fracture of&apos; platelets. The discontinuous fiber composite model of Kelly and Tyson is modgied to account for a changing distribution of fiber lengths during composite loading. The tensile properties at elevated temperatures were determined for the direc-tionally solidified eutectic oriented with platelets parallel to the tensile axis. The observed properties are attributed to the onset of plasticity of the CuAL2 phase above 150°C. DURING the investigation of whisker- and fiber-reinforced metallic matrix composites in recent years, two major problem areas have developed: 1) The fabrication of the composite involves tedious handling techniques in order to obtain a unidirection-ally aligned and uniformly spaced set of whiskers in the metal matrix. 2) Due to weak interfacial bond strengths or because of the formation of additional embrittling phases at the metal-fiber interface during long-time exposure or fabrication at elevated temperatures, many composite systems have exhibited considerably lower strengths than those predicted by a law of mixtures analysis.&apos; These problems have been bypassed by the technique of growing whiskers and plates of high-strength materials in a ductile metal matrix by controlled unidirectional eutectic solidification.2 The tensile properties of directionally solidified A1-CuA12 eutectic are presented here. This alloy consists of a ductile aluminum matrix, containing up to 5.7 wt pct Cu in solid solution, which is amenable to precipitation hardening by heat treatment and a reinforcing high modulus CuAlz intermetallic phase. The two phases are present in the form of alternating platelets or lamellae. The microstructural stability of this unidirectionally solidified alloy at elevated temperatures has been studied extensively.3.4 and preliminary tensile and bend tests have been reported. 5-7In the present investigation the tensile properties of the A1-CuA1, eutectic have been studied as a function of several ther-momechanical variables: solidification rate. heat treatment. rolling at elevated temperatures. and lamellar orientation. It was felt that the uniformity of structure and excellent interfacial bonding would give tensile properties concomitant with the metal matrix composite theory of strengthening proposed by Kelly and coson. 8-9 The tensile properties that were obtained point to a wide distribution of strengths for the CuAlZ platelets, which leads to large deviations from the predicted mechanical behavior for this composite. EXPERIMENTAL PROCEDURE Epitaxial Growth of Eutectic Alloy. The A1-CuA1, eutectic alloy was prepared by an epitaxial growth process. Sections of a master alloy ingot (total impurity content <0.008 pct) were placed in an alundum boat, melted. and directionally solidified to obtain a multigrained plate 12 by 2 by 4 in. This plate was tapered at one end to mate with a seed crystal 1; in. long and 4 by $ in. square. Then the seed-plate combination was placed in an alundum boat which sat in a quartz tube passing through the center of a horizontal resistance wound tube furnace. A dried argon atmosphere was maintained. The temperature gradient in the furnace was such that the liquid-solid interface of the eutectic alloy was located near the end of the furnace and could be observed through the quartz tube. Single-crystal plates were formed by melting the material back to the midpoint of the seed crystal of the desired platelet orientation and then epitaxially growing the plate from the seed by withdrawing the alundum boat from the furnace at a constant rate. This technique was used to produce aluminum and CuA12 lamellae parallel and perpendicular to the transverse direction on the plate. Metallographic examination showed that both phases were continuous across the original liquid-solid interface. It was also possible to grow a plate from two seeds placed side by side: and, although the lamellae of one seed were oriented at 90 deg to those of the second seed, the interface between the two grains remained parallel to the growth direction along the entire ingot length. Maintenance of a straight intergranular boundary during the solidification process was possible as long as both seeds were oriented with their original growth direction parallel to the solidification direction of the plate. Eutectic plates were directionally solidified at rates of 0.2, 1.0. and 4.7 cm per hr and sectioned transversely to the solidification direction to determine the apparent inter lamellar spacing of the lamellae. Metallographic examination was also employed

Jan 1, 1970

By W. C. Hagel, J. H. Westbrook

THERE has been a recent revival of interest in the intermetallic compound AgMg as an experimental material for study of the physical and chemical properties of simple ordered structures. Studies of mechanical behaviors,1-4 diffusion,5,6 and thermo-dynamic properties7&apos;8 have been reported. In several of these studies, heat treatments have been carried out in argon-filled silica capsules at temperatures as high as 750°C with no apparent adverse effects. The present authors were, therefore, startled to discover in the course of some yet unpublished work, that gross melting of near-stoichio-metric AgMg compositions occurred in such samples more than 100 deg below their melting point of about 800°C. This note is to report a brief series of experiments carried out to establish the reason for this behavior. Gross errors in sample composition and failure of furnace temperature controls were quickly eliminated as causes of melting. The first tangible lead came from chemical analysis of an AgMg sample which had melted during treatment at 750°C. A silicon content of 3.3 wt pct was found. Since satisfactory analyses had been obtained on the original as-cast ingot, contamination by diffusion and/or reaction with the fused silica capsule seemed a distinct possibility. A perplexing fact, however, was the apparently capricious incidence of the effect. Not only was it previously unknown, even in the experience of the present authors; but, in the early part of the present study, melting sometimes occurred and sometimes not with specimens treated under constant conditions. Indeed, one sample successfully survived a 750°C heat treatment and yet melted completely during the course of a subsequent anneal in an identical capsule at a lower temperature. To obtain evidence that silicon contamination could lower the melting point to the extent observed, the following experiment was performed. A series of ternary alloys was made up with a stoichiometric AgMg base and containing 0.1, 0.2, 0.4, 1, 2, and 4 wt pct Si. Melting was done in MgO crucibles under a cover of argon gas. After holding 10 to 20 min in the temperature range 850° to 900°C, the alloys were allowed to solidify in the crucible and the temperature during cooling automatically recorded with a Pt/Pt-10 Rh thermocouple. Results from the cooling curves are shown in Fig. 1. Checks within 2 to 5C° were obtained upon repeated melting, cooling, and freezing. The whole series of cooling curves as well as metallographic examination of the melted alloys established that the AgMg rich portion of the AgMg-Si quasibinary is an eutectic-type system. The melting point of AgMg is lowered from approximately 820°C in the pure stoichiometric binary9 to about 710°C in the saturated intermetallic phase. Since second phase was observed in all samples on cooling to room temperature, the solid solubility of AgMg for silicon evidently falls rapidly with decreasing temperature as indicated schematically by the dashed solvus in Fig. 1. It is thus established that a silicon content

Jan 1, 1963

By M. T. Hepworth, A. K. Stewart

Iron containing 0.1 pct A1 and -0.9 pct P by weight was internally oxidized in the temperature range 900° to 1300° C, where the bcc structure is stabilized by phosphorous. By measuring the depth of penetration of oxygen with time in an internally oxidized zone for an imposed surface oxygen potential, oxygen permeability was determined. The dgfusion coefficient of oxygen in iron was then calculated using known solubility data, yielding the expression: where Do is the diffusion coefficient of oxygen in bcc iron in sq cm per sec and T is temperature in OK. RECENTLY Hepworth, Smith, and Turkdoganl measured the diffusivity of oxygen in bcc iron and reported the temperature dependence of diffusivity from data determined in the a, and 6 temperature ranges. Subsequently Swisher and Turkdogan&apos; have measured the diffusivity of oxygen in fcc iron. Internal oxidation techniques were employed by these investigators and in this current study. The analysis of this technique is developed by wagner3 (presented in English by Hauffe4 and Rapp 5). In this present study bcc iron stabilized by phosphorous was used to determine oxygen diffusivity in the temperature range 900° to 1300°C. Meijerin 6 has studied oxygen permeability in this temperature range using bcc iron stabilized with 5 pct Sn. Other inves- tigators who have studied oxygen permeability in bcc iron at other temperatures are Schenck et al., 7 Bohen-kamp and Engell, 8 and Bradford. EXPERIMENTAL Electrolytic iron of 99.99 pct purity was alloyed to contain 0.897 pct P and 0.093 pct Al. The maximum weight percent phosphorous required to stabilize bcc iron between 910" and 1392°C is 0.51 pct as determined by Haughton,10 0.42 pct by Roquet and jegaden," and 0.58 pct by vogel,12 with the latter value preferred by Hansen.13 Microprobe analysis indicated that there was no segregation of the phosphorous either before or after permeability studies; therefore, the quantity of phosphorous added was assumed to be sufficient to stabilize the bcc structure. Furthermore, the permeability results of studies on this alloy agreed substantially with interpolated values from previous data on bcc iron.&apos; An ingot of the Fe-P-A1 alloy was hot-rolled to a l-in.-thick slab. Specimens were machined to dimensions: 13/8 by $ by 1/4 in. The experimental apparatus and procedure used have been described before.&apos; A constant oxygen potential was established by passing argon and hydrogen through a column of oxalic acid dihydrate, which has a water vapor pressure which is well-known as a function of temperature. Slab specimens were exposed to a gas mixture sufficiently lean in oxygen to prevent the formation of a surface oxide for predetermined temperature for selected times. The specimens were then quenched, sectioned, and examined metallo-graphically. All quenched specimens were iron-plated to provide protection from the outside sample edge during polishing. Fig. 1 shows a typical microstruc-ture for a specimen oxidized at 953°C for 48.00 hr at a water vapor-to-hydrogen pressure ratio of 0.20. DISCUSSION AND RESULTS The following equation was derived by Hepworth et al.&apos; from Wagner&apos;s kinetic expressions for internal oxidation:

Jan 1, 1969

By Regis M. N. Pelloux, N. J. Grant

Five or six alloys each in the systems Ni-C.v, Ni-Mo, and NL-W, spaced to cover the single phase areas as well as a part of the adjacent two-phase field, were prepared as uacuum-melted alloys. Tensile tests at room temperature and stress rupture tests at 1200° and 1500°F we.ve run for time periods to give fracture in 0.1 to 500 hr. Observations mere made of solid-solution and second-phase strengthening or uleakening, coupled with studies of ductility and the role of structure on the noted behavior patterns. THE development of stable creep-resistant alloys while broad and systematic is also highly empirical. A number of simple rules have been suggestedL-" but these are based on scant data. Whereas rules for low-temperature alloy strengthening can be applied with some success in more simple systems, the extension to behavior at high temperatures (greater than about 0.4 of the absolute melting temperature) is very poorly understood and has encountered important exceptions and deviations in terms of atom size or valency effects. In particular, the occurrence of both solid-solution weakening4,5 and second-phase weakening2 at high temperatures is of interest. MATERIALS AND PROCEDURE Nickel was chosen as the base material because of its important role in current high-temperature alloy applications, because of its freedom from a phase transformation, and because of wide solubilities for many elements of interest. The selected alloys were single- and two-phase structures in the Ni-Cr,6 Ni-Mo,7 and Ni-w 8 systems. The alloys were vacuum melted and cast, utilizing high-purity raw materials, in the form of 15 lb ingots. They were readily forged into 1/2-in. bar stock (except the two highest chromium alloys). The alloy compositions are shown in Table I. Typical impurity values are: Carbon: Max 0.03 pct (except for 30 and 35 pct Cr alloys which had 0.07) Nitrogen: Max 0.005 pct (except for two of the Cr alloys which had 0.05) Sulfur: Max 0.004 pct Silicon: Max 0.05 pct Each alloy was solution treated (air quenched) to produce comparable grain size. The two-phase alloys were then overaged in an effort to produce a stable structure for testing at 1200° and 1500°F, The results are summarized in Table 11. Following the heat treatments outlined in Table 11, the bars were machined to a gage section of 1.25-in. long by 0.250-in. diam. In addition to room-temperature tensile tests, stress-rupture tests were run at 1200" and 1500°F for time periods from 0.1 to about 500 hr. RESULTS Room-Temperature Mechanical Properties—The ultimate tensile strength, total elongation, and reduction of area values for all the alloys are plotted vs atomic percent of the solute element in Fig. 1. It can be seen that for the same amount of solute element the ultimate tensile strength increases in the order chromium, molybdenum, tungsten. Elongation increases (reduction of area decreases) with increasing amounts of solute for all the solid solution alloys, the values ranging from 50 to 70 pct. The ultimate tensile strength values for the two-

Jan 1, 1961

By Anal J. Mehta, Theodore D. Tiemann

Growing demand for steel and increasing dependence upon foreign ore makes the need for developing the technology for treatment of low-grade iron ores greater than ever before• Representative of these added interests were the studies carried on at the University of Wisconsin• These studies included among others: anionic and cationic flotation, magnetic separation, roasting followed by magnetic separation, electrostatic separation, a hydrogen reduction process,6,7 and caustic digestion• The idea of removing silica by caustic extraction is not new•-1; The principle of concentrating siliceous iron ores by this method is based on the fact that silica is soluble in sodium hydroxide solution while iron oxides are essentially insoluble• For this process to be economically feasible, it is believed that some method of recovering silica from solution as a marketable by-product, with recycling of spent liquor is necessary. Precipitation of silica with carbon dioxide will allow subsequent causticizing of the spent liquor with lime• Caustic thus produced can be recycled for digestion• A flowsheet of the envisioned process is given in [Fig• 1] The purpose of this paper is to describe results obtained from the investigation of carbon dioxide precipitation of silica from sodium silicate solutions, which could be later applied to the caustic extraction process to treat low grade siliceous iron ores, particularly taconites.15 Theoretical Considerations The soluble silicates of sodium include sodium orthosilicate (2Na2O•SiO2), sodium metasilicate (Na20•SiO2), sodium disilicate (Na1O•2SiO2), and more highly siliceous products approaching Na2O•4SiO2• These materials have been described in detail by Vail•16 Stones has reported that the extraction of silica is not significantly affected by the amount of silica in solution until the Si02/Na20 ratio exceeds that of orthosilicate (Ratio = 1/2)• However, as the Si02/Na2O ratio exceeds that of metasilicate (Ratio = 1), silica extraction is significantly impaired• The present experimental work was confined to orthosilicate and metasilicate solutions, as to be successful the envisioned commercial process for the extraction of silica from siliceous iron ores would operate in this region. The mechanism of extraction of silica from aqueous sodium silicate solutions is complex in nature. For the carbon dioxide process-18 of core and mold making in which silica is also precipitated from sodium silicate solutions by gassing with carbon dioxide, the reaction of aqueous silicates with gaseous carbon dioxide has been represented by the equations: [ ] However, these equations are very much oversimplified• It has been shown that the reaction between aqueous sodium silicates and carbon dioxide gas is ionic in nature 18 Considering this fact and the mechanism for digestion of silica in aqueous sodium hydroxide, the overall conversion of aqueous sodium silicates to solid silica may be represented in ionic form by the following equations: [ ] Silicon in the silicate ion is shown here with a coordination number of 6• This may be in doubt, but it is known that ion (SiF°)-2 exists; it seems logical that the Si (OH) e 2 ion should be equally capable of existence•

Jan 1, 1977

By R. V. Riley

IN the metallographic examination of the alloys of iron and silicon, several investigators1-&apos; have reported on the occurrence of an unusual type of etched structure, particularly in the alloys of higher silicon content. This, the so-called "barley shell" structure, has been observed with iron-silicon alloys over a wide range of silicon content, and under certain circumstances it can be seen upon the micro-sections of pure iron. The barley shell structure may be demonstrated most easily with iron-silicon alloys in the range 8 to 20 pct Si after etching in a hydrofluoric acid base etchant. Two etchants which produce the structure are: Corson&apos;s reagent, which is 2 parts hydrofluoric acid, 1 part nitric acid, and 2 parts glycerol; and picric acid reagent, which is 1 part hydrofluoric acid and 1 part saturated solution of picric acid in alcohol. Both when freshly prepared and used for etching commercial silicon-iron alloys containing 14 to 16 pct Si, invariably produce the barley shell structure shown in Fig. la. It is now well known that the barley shell structure is a pseudomorph and the true structure of an alloy of this composition consists of a single phase of silico-ferrite together with graphite as shown in Fig. lb. Lower silicon alloys and even pure electrolytic iron may also be etched in the above reagents to give the barley shell provided the etchant has been either: 1—Stored in contact with glass or silica, or 2—used previously for etching an iron containing silicon. Pure iron etched in perfectly pure hydrofluoric acid base etchants free from silicon contamination gives a normal structure free from the barley shells. Therefore, although the hydrofluoric acid in the reagent primarily is responsible for the barley shells, silicon, or its compounds, also must be present, either in the etching reagent or in the specimen. It was of considerable interest to the author to read the paper by Wachtell,? in which the barley shell etch was deliberately used for the identification of the boundaries of high and low silicon areas in diffusion experiments made upon laminate bars of compacted and sintered pure iron and ferrosili-con powders. This method of utilizing the barley shell etch is novel and in the hands of the investigator gave a useful differentiation between the high and low silicon areas in those specimens. For the reasons already given, however, the technique is not to be regarded as of universal application. Misleading results might be obtained, for example, if two or more specimens were etched in the same etchant. Fresh pure reagents only must be used each time. Provided this is done and the investigators are well aware of the limitations of the method, then the barley shell pseudomorph can be made of limited use in distinguishing between higher and lower silicon areas in a microspecimen of a ferrous material. The greatest of care must be exercised in the interpretation of the results which may be regarded as qualitative only and may, in fact, not be specific to silicon alloys.

Jan 1, 1952

By Edna A. Dancy, Ronald L. Pastorek, Gerhard J. Derge

In an earlier study1 in this laboratory, it was found that there is a minimum in the specific conductance of Ni-S melts in the region of the stoichiometric composition, Ni3S2. This and similar observations on other sulfide1 and telluride2 systems suggest that short-range order exists in the molten phase for several hundred degrees above the melting point, and a qualitative energy-band model has been proposed, with intrinsic semiconduction at the stoichiometric composition and degenerate electron and hole conduction at metal- and tellurium-rich compositions. This suggestion has been substantiated for the telluride systems by Seebeck coefficient measurements which showed a change in sign from negative on the metal-rich side to positive on the tellurium-rich side. In the present investigation, in order to substantiate still further the proposed model, Seebeck coefficient determinations have been extended to the Ni-S system over a composition range in the vicinity of Ni3S2. The experimental method was essentially the same as that used for the telluride systems, with minor modifications on cells for high sulfur melts to permit the use of tungsten wires and W— W-Re th~rmocouples instead of the chrome1 or alumel wires and chromel-alumel thermocouples originally used. Chrome1 and alumel both deteriorate very rapidly in atmospheres containing sulfur. The Ni-S alloys were prepared as described in the conductivity paper. Initially, a portion of the solidified melt was analyzed at the end of a run, but after this was found to be inaccurate because of segregation during cooling, the whole sample was analyzed. The nickel content, only, was determined, the sulfur content being obtained by difference. The results are summarized graphically in Fig. 1, and clearly show a change in the sign of the Seebeck coefficient in the region of the stoichiometric composition. This change of sign near Ni3S2, coupled with the minimum in the conductivity, is suggestive of an intrinsic semiconductor at the stoichiometric composition, with degenerate electron and hole conduction on either side of this composition, in keeping with the proposed model. The negative temperature coefficient of conductivity, normally indicative of metallic conduction, is not inconsistent with this model. In the completely degenerate region it would be expected, while in the vicinity of Ni3S2 the suggestion originally made by Argyriades, Derge, and pound3 for the Fe-S system can probably be applied. They proposed that the forbidden gap between the valence band and the conduction band is small, and that the increase in the number of the conducting species with increase in temperature is not large enough to compensate for the loss of mobility through thermal scattering. The research was sponsored by the Office of Naval Research under Contract NONR-760(22) Project NR 039-081. &apos;E. A. Dancy and G. J. Derge: Trans. Met. Soc. Aime, 1963, vol. 227, pp. 1034-38. &apos;E. A. Dancy: Trans. Vet. soc. AIME. 1964, vol. 233, pp. 270-77. &apos;D. Argyriades, G. Derge, and G. M. Pound: Trans. Met. Soc. . 1959, vol. 215, pp. 909-12.

Jan 1, 1965

By P. A. Laxen, H. R. Spedden, A. M. Gaudin

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface1 are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.2,3 Study of the adsorption of sodium from an aqueous solution on quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained.4,5 Three main factors which appeared likely to affect the adsorption of sodium are: 1-concentration of sodium in the solution, 2-concentration of other cations in the solution, and 3-anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in the amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxylion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory4 except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying5 To minimize the laborious preparation of quartz, experiments were made to determine whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na&apos; activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot II) and 2000 (lot III) as determined by the Bloecher method.6 Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.7 It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß radiation and a 1.30 mev ? radiation. The decay scheme is illustrated in the following equation: [Y Nam S. - &apos;Net 3 years] The ß radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang8 The original active material was 1 ml of solution containing 1 millicurie of Na22 as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen5 In brief, it included the following steps: 1-Ascertainment of linearity between concentration of Na22 and activity measured. 2-Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3-Taking precautions to avoid evaporation of water during centrifuging.

Jan 1, 1952

By D. Turnbull, R. E. Cech

EXPERIMENTAL studies of precipitation of iron from solid solution in copper by Gordon and Cohen 1, Bitter and Kaufmann 2 and Smith 3 revealed that the precipitate particles were initially paramagnetic but could be changed to a ferromagnetic

Jan 1, 1955