Search Documents

By W. W. Yankie, A. T. Chatas

This paper is written as a discussion of the paper, "Buckling of Tubing in Pumping Wells, Its Effects and Means for Controlling It" by Arthur Lubinski and K. A. Blenkarn, which war published in the March, 1957, issue of Journal oP Petroleum Technology. An analogy is drawn between the buckling of tubing in pumping wells and a fiube, fitted with frictionless pistom, linked by an inelastic rod, and which is subject to an internal pressure. A simple derivation shows that the critical internal pressure exerts a hydrostatic force on the pisfon which is close to the Euler load for compression buckling of the same tube. While the results agree with those of Ref. I, the basis of calculations has been changed and clarified. The presence of internal upsets at the pistons is discussed. INTRODUCTION In the Appendix, Lubinski and Blenkarn state that a tube with ends closed by frietionless pistons connected by an inelastic rod (Fig. 1) will behave as a column loaded with a force equal to the tension force in the rod. They note that, while the fluid may not resist a shear force, the moment in every cross section is piston force multiplied by the elastic line deflection (c.f., the loaded column). Since the equations of the elastic lines are similar in the two cases, the solution is carried over from the loaded column. On the contrary it is suggested that while the method of solution remains unchanged from the column case, the actual stress distribution is different, a fact which is taken into account in this note. A simple method of approximating the buckling pressure is given, and their reasoning in our mathematical language is continued. GENERAL EQUATIONS The equation of an elastic line, initially straight in the x direction (Fig. 2), is given by In the case of a loaded column, this may be written: For the pressurized tube it was shown, by analogy with the loaded column, that tion has a solution that, for P, = EI/P, any deflection is stable (a criterion for buckling). An attempt will be made to describe more precisely, the forces acting on the tube, and to analyze the buckling condi,tions. DISCUSSION If the tube assumed a deflected position, the volume between the pistons would increase so that in deflecting, the energy of the fluid would decrease. When the increase in elastic energy of the tube (due to bending) is equal to the decrease of fluid pressure energy, buckling conditions exist. Analyzing the forces on the tube (Fig. 3), two transverse forces, T,, T,, exerted by the pistons, are balanced by a resultant of the pressure elements which are linearly dependent on the local curvature of the elastic line (Fig. 4). Unlike most buckling cases, the forces depend on the shape of the elastic line, a condition that makes a rigorous mathematical treatment difficult. Several approximations may be used to clarify the problem.

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytical expressions derived previously are used to describe quantitatively effects on macrosegregation of some solidification and mold design variables. Al-4.5 pct Cu alloy is used as example. It is shown that abrupt changes in heat transfer rate result in solute-rich or solute-poor "bands". Severe solute-rich bands accowzpany "reheating" that can result, for example, from abrupt formation of an air gap at a mold-metal interface. With planar isotherms, solute-poor regions also result from reduction in cross section through which fluid flow to feed shrinkage takes place. It is suggested that the negative "cone" of segregation often found at the base of large ingots results from this reduction in cross section for feeding. Consideration is given to the positive and negative segregation to be expected in laboratory ingots in association with changes in ingot cross section. Under-riser positive segregation is considered and it is concluded this segregation results when vertical temperature gradient is low in the region of the riser; the segregation is accentuated by the temperature gradient reversal which can occur in inadequately insulated risers ("'hot tops"). Finally it is shown for Al-4.5 pct Cu alloy that the assumption of constant k and p in analytic solutions gives calculated results close to those obtained for the case of ziariable k and 0. A basic "local solute redistribution equation" was derived earlier' for calculation of macrosegregation resulting from flow of solute-rich liquid to feed solidification shrinkage, thermal contraction, and/or other contractions occurring during solidification. This expression relates fraction liquid, g~, to liquid composition, CL, at a given position x, y, z, in a solidifying Eq. [I] is for the general case of three-dimensional heat and fluid flow assuming constant solid (but not necessarily liquid) density during solidification, negligible net solute change from diffusion, and no pore formation. In this paper we first demonstrate application of this equation for calculation of macrosegregation in several examples involving one-dimensional heat and fluid flow. Specifically considered are examples in which segregation results from sudden changes in heat flow conditions. Next, Eq. [I] is used to describe segregation in examples where isotherms remain planar but where fluid flow is no longer one-dimensional. Application of this expression illustrates the type of segregation to be expected in unidirectionally solidified ingots of gradually or abruptly varying cross section. For segregation calculations, A1-4.5 pct Cu alloy is employed with constant k and p Vz = 0.172, 4 = 0.055), eutectic composition (CE = 33 pct Cu). In all examples, fraction eutectic is neglected in velocity calculations; this was previously shown to introduce little error.' A linear distribution of fraction liquid in the liquid-solid zone is assumed. In a concluding section it is shown that the assumption employed of constant k and /3 gives results close to those obtained when the actual (variable) values of k and 0 are employed.

Jan 1, 1969

By Thomas A. Read

THE internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of l00 when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose-that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals will be presented. EXPERIMENTAL PROCEDURE The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrement A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were .made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders ¼ in. in diameter and 1 ½ to 2 ½ in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is ¼ in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By J. T. Norton, J. G. McMullin

An 1820°C isothermal cross section of the Ti-Ta-C ternary diagram was prepared from X-ray diffraction and metallographic data. No phases other than those appearing in the three binary diagrams were observed. At temperatures above the titanium transition temperature titanium and tantalum form a complete series of solid solutions containing up to 2 atomic pct C. The phases Tic and TaC also form a continuous series of solid solutions extending across the diagram. PREVIOUS work on this alloy system was very limited. Of the three binary constitution diagrams involved, only one, the Ta-C system was available in the literature. Preliminary data on the other two systems was received from the investigators during the course of the investigation and both have been published in recent months. It had been shown that Tic and TaC formed a continuous series of solid solutions, but the range of carbon content in this phase was not known. While Ta2C had been described, its solubility for or reactions with other carbides had not been reported. It was not known whether or not any ternary compounds occurred in the system. The present program was undertaken to determine experimentally the general form of the ternary diagram. It is hoped that the results will be of value in furthering the development of sintered carbide cutting materials and high temperature ceramets, many of which contain combinations of Tic and TaC. The Binary Systems Of the three binary diagrams involved only that of Ta-C was available at the time this project was started. The diagram of Ellinger¹ redrawn in Fig. 1, shows a hexagonal phase Ta2C having a very small composition range and a cubic TaC phase having a composition range of from 40 to 50 atomic pct C. The authors made a separate determination of the composition range of TaC using lattice constant values and found the range to extend from 40 to 49.7 atomic pct C in good agreement with Ellinger's diagram. Two determinations of the Ti-Ta system have appeared recently.2,3 These two diagrams are in good agreement and show that ß titanium and tantalum form a complete series of solid solutions. The Ti-C diagram by Cadoff and Nielsen4 shows a very limited solubility of carbon in both a and ß titanium. The single carbide formed persists over a wide range of carbon contents. Several values for the upper limit of carbon content of this phase have been reported."' The highest value obtained in the M.I.T. Laboratory was 47.5 atomic pct C with a lattice constant of 4.328?.5 Fattinger7 describes a gas carburization method which he claims produces stoichiometric Tic although he does not present any data showing that he actually had 50 atomic pct combined carbon. Several complete analyses on

Jan 1, 1954

By Loyd R. Kern

A procedure for determining the behavior of a reservoir under a gas or water injection program was reported by Buckley and Levertt in 1942.1 This method, which allowed the calculation of the phase saturation distribution behind the front of a displacing fluid, has been extended to apply to a more general situation. The reservoir may initially contain flowing quantities of the displacing fluid, or the fluid in the reservoir may be above saturation pressure SO that solution effects are present. Production may occur behind the front as in the case of a well which is produced after breakthrough of the displacing fluid. The calculating procedure is simplified in that the graphical integration necessary to determine breakthrough saturation is eliminated by performing a direct integration and the graphical differentiation necessary to determine saturation distribution is eliminated by representing the displacing phase fraction of the flowing stream by an empirical equation. This representation results in simple expressions for the producing gas or water/oil ratio and cumulative production. INTRODUCTION A method for the calculation of the saturation distribution behind the front (interface between the displaced and displacing phases in a gas injection or water flooding operation) was reported by Buckley and Leverett in 1942. The method leads to a curve for the saturation distribution which is double-valued; consequently, part of' the curve was interpreted to be physically meaningless. That part of the curve which has physical significance was determined by a graphical integra-tion (material balance). In this paper it is shown that the integration may be performed analytically with a resulting equation for the saturation of the displacing phase at the front. The case in which the displacing fluid is initially flowing and the case in which the reservoir is initially above the saturation pressure so that some injected gas goes into solution are included in the integration. The calculations are considerably simplified by representing the fraction of the flowing stream which is oil by an exponential function of saturation. The methods is extended to apply approximately to reservoirs in which wells located between the injection well and the front are produced. An illustrative example utilizing the methods presented is included. RESERVOIR BELOW SATURATION PRESSURE In the case of a water flooding operation or in the case of a gas injection operation in which no gas goes into solution in the displaced oil, the equation for saturation in a linear flow system as a function of time and position as given by Buckley and Leverett is where* q = total reservoir volume flow rate, rvb/day A = cross sectional area of system, sq ft / = porosity of formation x = distance from injection point, ft t = time, days Pj = saturation of the displacing phase /dx velocity of planes of constant saturation, ft/day *The nomenclature used here is not the same as that used by Buckley and Leverett A complete nomenclature is given in Appendix A.

Jan 1, 1952

By C. B. Dudley

bas shown us that the railroads of this country can save several milt liohs a par by adopting uniform rail sections, and as unfortunately for him, he cannot patent his idea, it only remains for the railroads to adopt it, and to thank him for his payer. Dr. C. B. Dudley, Altoona, Pa. : 111 rising to close this interestin~ discussion, I want, in the first place, to thank every one who has contributed to it for his full and open criticism. The work tvhich has been done on steel rails, and which has been diwu&e,l here Juring thee two days, was not done to establish any pet theories, nor to make out that any person was great or any person small, but with a sincere desire to get at what is the truth in regard to the wedring capacity of steel rails. There are enormous commercial coneiderations invoIved in this question, and, as I look at the matter, the more honest criticism and fair discussion there is, the Inore likely it is that the truth will appear. Ad first I would like to say that it seems to me very little has been said here upon the main conclusion of the paper, namely, that the softer rails give the better wear. All sorts of side issues have been discussed; but this poiat, which is really the principal one at issue, has been largely ignored, aid I cannot But feel that it still remains unshaken. Witb regard to ohemists end chemical work, there has been considerable said tending to throw discredib on chemists and their work; and while I believe that there have been in the past, are now, and may be in the futnre, a good many poor chemical analyses made, X also believe that chemists are, as a rule, as honest and competent as gentlemen who belong to other professiomc. There are chemisb who are chemists, and who are not chemists. The determination of -manganese has bee* called in question. Now I think the chemist at almost every steel works in the country will tell you that, in his experience, the manganese diffe1.s in different parts of the same ingot. Mr. T. T. Morrell, chemist of the Camhria Iron Company, whom I believe to be s thoroughly competent and hone6t chemist, tells me that he has often found different amounts of manganese in different parts of the same ingot. Come with me to Altoona, and I will take you into the machine shop where steel is king cut aud shaped, and I will show you that it is often necessary to stop the lathe or planer and take a cold chisel to cut oat a hard spot, or else ntn the risk of breaking the tool. This hard spot is simply a pttrt of the syiegel which was not thoraughiy mixed with the ma

Jan 1, 1881

Book Review MEXICO UNDER CARRANZA. By Thomas E. Gibbon, Los Angeles, California. Doubleday Page and Co., New York, 1919, 270 pp., 711/2 X 5 in. $1.50. A vivid, accurate, convincing summing up of the Mexican problem as it confronts us today, devoid of sensationalism or bigotry. A compelling narrative of the relations of the Carranza Government and our own from Oct. 15, 1915, when it was recognized as the de facto government of Mexico, to the present time. It shows the absolute lack of promises kept or lived up to either with its own people or the United States. This is not done by invective or the indiscriminate use of adjectives but by quoting from the instruments on record on both sides of the case. The driving of the Red Cross out of Mexico, which condemned many of the native peons to starvation, and the interference with the Pershing Punitive Expedition are merely mentioned, but the crying crime against the Mexican people, who have sunk to unbelievable depths of misery obscured, but not exceeded, by the sufferings in Europe, is held up in a clarified light. Two illuminating chapters are devoted to the character and treatment of foreign investments in Mexico, Which are a complete refutation of the common statement that Mexico has been exploited remorselessly by the foreign investor. The conces-sions given by Diaz in the days of his regime most condemned are nowise as large nor the land grants as extensive nor the title so absolute as those granted to the railroad builders of our own transcontinental systems and other of our nationally subsidized works. This is not left to further argument but is settled by quoting the various official instruments and not at all in a tedious way. The author's concluding chapter is a picture of the Mexican people from Aztec times, when they had reached a civilization which gave them a better calendar than the Roman Empire ever had until modern times, to their present unhappy and pitiful condition. He concludes, basing his findings on parallel historical downfalls of a once proud people, that present conditions are the natural result of the absolute domination of an alien minority. He grants, of course, that there are many estimable Latin-Mexicans of integrity, ability and charm, but maintains that the dominant minority has continually degraded in fulfillment of the sociological law that the sure revenge of the servile class is found in the corruption of the master class. The book is replete with historical and literary allusions which, added to the pleasing style of the accomplished author, make fascinating the account of one of the world's great tragedies. Mr. Gibbon is a lawyer who has spent much time in Mexico and shows an understanding of the native people not shared by all writers on the Mexican problem. A distinct addition to all literature on the subject. P. E. B.

Jan 8, 1919

By George F. Comstock

It has been known for many years that the alloy containing 90 per cent. copper and 10 per cent. aluminum can be hardened, like steel, by quenching from a suitable temperature, and that the hardened alloy can be softened again by annealing or drawing the temper. It does not seem to be generally appreciated, however, that the effect of the first slight reheating after quenching is actually increased hardness, the softening effect not taking place until a certain temperature of "drawing" has been exceeded. This paper gives the results of a few experiments on various specimens of cast 10 per cent. aluminum bronze, quenched for maximum hardness, and subsequcntly annealed at different temperatures. The hardness measurements were made with both a scleroscope and a standard Swedish Brinell machine; some peculiarities of the scleroscope test on this material are described. The author is not aware of many previous investigations of the hardness of this alloy when quenched and drawn, but two important papers on the subject should be mentioned. The earliest was by Portevin and Arnou,1 in which it was stated that tempering quenched 10 per cent. aluminum bronze at 400" C. increased the hardness as compared with the quenched untempered alloy and that reheating above that temperature ' was necessary to obtain any softening effect. A later paper was by Seidell and Horvitz,2 who mentioned Portevin and Arnou's work, but did not report any increase in hardness obtained

Jan 1, 1925

By David W. James

DURING a recent investigation of the transition from a planar to a nonplanar solid/liquid interface for the systems H20-NH4F and 0-AIR,' an apparatus was developed which enabled the morphology of the ice-water interface to be examined during the transition. The slightly curved interface was viewed at a glancing angle with a Bausch and Lomb X30 stereomicro-scope. The interface was obliquely illuminated by a polarized light source. It was thus possible to differentiate between small projections or depressions at the interface, both by a shadowing effect and by the way in which they distorted the colored interference fringes across a particular crystal surface. Many attempts were made to photograph the various stages of interface breakdown. Unfortunately, the limited depth of focus of the microscope rendered the system unsuitable for photographic recording. Visual examination, however, was facilitated by continuous adjustment of the microscope focus control. The following observations of the interface transition were recorded for dilute solutions of ammonium fluoride in water. They are compared with iller's postulated morphologies shown in Fig. 1. i) The initial departure from planarity was characterized by the appearance of a large number of small depressions or "pores" in the interface. ii) The pores were arranged in wavy rows all lying roughly in the same direction within a particular grain. iii) The pores did not appear to form near to grain boundaries. iv) The pores appeared in certain grains before others. v) The transition from the pore structure to the elongated cell structure, Fig. l(d), was difficult to follow. It occurred quite rapidly and no truly irregular cell structure, Fig. l(c), was noticed. vi) The elongated cells gradually became more uniform in size and shape, with straight cell boundaries. They remained elongated, however, and no regular hexagonal cells were observed, cf. Fig. l(e). Several conclusions may be drawn from these observations. Firstly, the appearance of a poxed or, more accurately, a pore structure can be used as a criterion for the onset of constitutional supercooling. Care should, of course, be taken to distinguish between the true pore structure and artifacts caused by splashed-back liquid, particles of oxide, or inefficient decantation of liquid retained between cell boundaries, as described by Spittle et al? Secondly, and contrary to the suggestions of Tiller el l., it seems that interfacial perturbations are characterized not by curved projections but by small depressions or pores. A recent independent investigation by Biloni, Bolling, and cole5 reported in this issue indicates that the depressions might be explained in terms of dislocations intersecting the solid/liquid interface. It is possible that the dislocation concentration is reduced in the vicinity of grain boundaries. This would then explain the grain boundary depleted areas noted in (iii) above. This work was partially supported by the Air Force Office of Scientific Research, Contract No. AF 49-(638)-1029.

Jan 1, 1967

By L. C. Kern

This paper presents information on the use of a new propping agent (malleable aluminum particles) which has been used successfully for producing high-conductivity fractures. The conductivity of a packed fracture depends on the width of the fracture as well as the permeability of the propping material. It is significant that the flow capacity of a propped crack is often increased many fold by propping the crack with a sparse distribution of particles. However, the flow capacity of a sparsely propped crack can be limited by two phenomena: (I) crushing of the propping particles, and (2) embedment of the propping particles in the formation walls. Malleable aluminum particles exhibit interesting properties which tend to overcome these limitations. As high loads are applied to the particles they will deform slightly, rather than shattering. The deformation results in a greater bearing area against the formation wall. This reduces the stress on the particle and reduces particle penetration into the formation. The behavior of aluminum particles under load and the bearing capacities of serveral formation rocks have been measured in the laboratory. By properly using these data, as explained in this paper, the flow capacities of aluminum-propped cracks can be calculated for a variety of conditions. Aluminum particles have been used successfully in the field to prop fractures. Where high-conductivity fractures were needed, the aluminum-propped fractures have given greater well stimulation than could have been expected for conventional fracturing processes. INTRODUCTION The purpose of a hydraulic fracture treatment is to create a conductive channel from the wellbore out into the oil or gas formation. The word conductive is emphasized because we believe that the fracture conductivity (flow capacity) is one of the most important factors influencing fracturing results. Previous papers have pointed out the additional well stimulation that can sometimes be achieved by increasing fracture conductivity. Several years ago, we investigated in some detail the effect of fracture conductivity on productivity increases to be expeced from vertical fractures. Both electrical analog and theoretical studies of unsteady-state flow behavior were made. A discussion of the electrical analog equipment and some of the results of the study were given in a previous paper' by Dyes, Kemp and Caudle. Further details were given recently by McGuire and Sikora.5 Fig. 1 shows the remarkable influence of relative fracture flow capacity and length on well stimulation. Briefly, the study indicates the following. 1. High-permeability formations require high-conductivity cracks for best results. 2. The longer the crack, the higher the fracture conductivity required for best results. 3. If the conductivity of the crack is very large compared to the formation (i.e., flow is not being limited by crack conductivity), then the longer the fracture, the better will be the results. Judging from recently published articles,1,314 there is current interest in methods for obtaining high fracture conductivities. Hence, we would like to present in this paper a discussion of a new fracture propping process (use of aluminum particle) which we have used successfully to obtain highly conductive fractures. There are several factors which influence the conductivity of a propped crack. Conventional fracturing techniques frequently result in a crack completely packed with fracturing sand. For such conditions, the crack conductivity is the product of the width of the packed fracture and the permeability of the propping material. It is significant that a large increase in conductivity sometimes can be obtained by propping with particles which are distributed sparsely (less than a

By W. C. Ellis, E. S. Greiner

WHEN metallic materials are deformed plastically, the process may be considered as one in which hardening and recovery occur simultaneously. The net hardening is that produced by deformation in the absence of recovery lessened by recovery during and immediately following deformation. Strain hardening takes place through movements of large groups of atoms acting to a degree as an entity. A complex microstress system is developed. Recovery is a diffusive-type process involving single atoms or, at most, only a few atoms in concerted action. This is accompanied by elastic strain relaxation. Recovery is strongly temperature-dependent. The driving energy for the process resides in thermal fluctuations of the atoms augmented by the energy of the stress field producing the deformation, and by that produced by the deformation. At very low temperatures recovery is essentially absent, or very small. At high temperatures in the hot working range, recovery is so rapid that deformation results in no appreciable net hardening. The interplay of strain-hardening and recovery results in differing end structures depending on the temperature and the strain rate of the process. For example, there is a prominent difference in the spacing of the slip markings and in the detail of X-ray diffraction patterns. High temperatures and slow strain rates favor a wide spacing of slip markings and sharp reflections.',' This suggests that change in rate of the recovery concurrent with deformation modifies to a degree the manner of the deformation. Different slip systems may operate. For very slow rates, the mechanism may, as has been suggested, differ from that of "classical slip." In the experimental work that follows the findings will be interpreted from the point of view developed in this section. Recovery and Electrical Conductivity Electrical conductivity is a sensitive indicator of the state of strain in a material3' * and was used in this investigation. The materials studied in wire form were: OFHC copper, a high purity (99.99 pct) and 2s grade aluminum, and grade A nickel. Wire annealed and initially 0.050 in. in diam was drawn through diamond dies in a simple holder maintained at 25", —75°, or — 195°C. Precautions were taken that for each material all conditions of drawing were the same except the temperature. Electrical resistivity was measured for each condition at 20°C. This was done as soon as practical after drawing to minimize possible room temperature recovery. The data for the four materials are plotted in Fig. 1 in terms of the change in resistivity for drawing at the several temperatures. The effect of temperature of drawing on the increase in resistivity is most pronounced for copper. Drawing at 25°C to 80 pct reduction in area increases the resistivity approximately 2 pct; drawing at —195°C to the same reduction increases the resistivity about 6 pct. The increase in resistivity" & in this metal is due to extra scattering of conduction electrons originating in the lack of orderly arrangement of the atoms induced by the deformation process. It has been suggested

Jan 1, 1953

By R. W. Raymond

to same extent, the assumptions tinderlying Dr. Ilu?ley's con alusions. These amrrmptions are: that 'the loss of metal per million tons of trafffc, depends, first upon the circrtnistances under which the rail is worn; secondly, upon the proportions of its various constituents, ancl that the anlorlnt of loss is afEect~d by eacb constitnent in a cer tain ratio, so that if the circunlstances were the same for all tlie mils, the wear per nliilion tons might he upproxi91ately expre~sed by an equation of the form I + Cc + Pp + SR + Mm = R, io wtlioh I is an unknown valne, dependi~.rg on the quantity of iron (and other ingre dients not determined) in the rail, and assumed to be constant for all the rails ; c, p, s, and m are the experimentally determined quan tities of carhon, phosphorus, sulphur, and manganese, as tabulater1 in YIates VT and VII of Dr. Dudley's paper; and R is the experirnen tdlly dcterlnincd wear per million tons; while C, P, S, and M are onknown wfficients. In other words, it is assunled that the differ ence in wear is proportional to a difference in c, p, s, or m, and that the effects of a change in the amonnt of either are independent of the amount of the rest-—within the experinlental limit5 of the problem. It is also assr~med that sulphar, copper, and other ingredients, not determined, are qually present in all the rails, or at least {lo not affect the wear, since I is taken as constant. Dr. Dudley tacitly assumes the coefficient6 C, P, S, and M to be positive; and assigns certain valries to them, by means of which he redom t.he equation to the form I + Pa: = R, x being equal to cc + Es +Mm i Pp, or tjje uanjbe,. of so-called phosphorus units in the rail. But we do not have R directly given under constant circumstances. The varying weights (per engine, car, or train) and the varying epds, we must neglect for lack of data, and assume that in these rwpects the rails examined have been treated srlbstantially alike. But there remain the varying conditions as to track, which mnst he elirninsted. Dr. Dudley gives six clrlsses, four of which contain 8 rails each, and two 16 rails each. Beginning with the 6~st (tangent grade), take the mean of the figures expressing wear for that clam; and continaing tliis process through the other five, we obtain six expressions in quantity of loss 'by wear, which we assome tc, represent, in their differences, the varying conditions of the trarli, with respect to grade and direction. We now take the mean of these moans (giving double weight to the gmiip containing 16 ohwrvafieras). This general rnean is the 10 of metal per million tons of trafio for a rail of avorage constitution under mean ciroumstances.

Jan 1, 1881

By Walter R. Hibbard, Harold Margolin

DURING preliminary tests on the aging of a Cu-plus 5 pct Ag alloy,' a specimen which had been overaged 24 hr at 550°C was annealed in a nitrogen-hydrogen atmosphere first for 2 hr and then for an additional 28 hr at 600°C. After each anneal the specimen was cooled to room temperature in about ½ hr and X-ray photograms were made. The first film, Fig. la, revealed two sets of copper-base lines, one intense and corresponding to the parameter at 550°C, the other fainter and shifted away from the beam, corresponding to the larger parameter at 600°C (see arrows). The 30-hr film, Fig. lb, revealed the same two sets of copper-base lines with a reversal of intensity. In neither case do the copper lines form a broad band which would be indicative of a range of compositions. This phenomenon is thus a "discontinuous" type of solution. A similar phenomenon was observed in a Ag-rich Cu-Ag alloy.' Finlay and Hibbard9 have suggested that directional rather than random solution of precipitate occurs in some alloys. Conceivably, for Cu-Ag alloys, the matrix-transition-precipitate precipitation sequence is reversible for the re-solution of the precipitate caused by rapidly raising the annealing temperature of an overaged specimen. A copper-base transition structure supersaturated with solute might be formed around the precipitate as it dissolves, thus obviating the necessity for a gradually changing solute composition of the matrix. The solute atoms then might be transferred rapidly and locally from the transition to the matrix phase in the proper amount and at the proper location to obtain directly the new ex- panded solid solution. The theory implies a minimum of diEusion of solute in the matrix (i.e., no significant range of matrix composition) and possibly suggests that the composition of the transition structure will vary with the conditions of re-solution. A transition copper phase found in aged Cu-Ag alloys1 might fulfill this function. Evidence regarding this suggestion could be obtained in Cu-Ag alloys by overaging a specimen until no trace of the expanded copper lattice is present and then subjecting the specimen to a retrogression treatment. Re-appearance of the transition copper phase would confirm the theory. Additional details could be secured by varying both aging and retrogression temperatures. References 'H. Margolin and W. R. Hibbard, Jr.: Effect of Ternary Additions on the Age Hardening of a Copper-Silver Alloy. Trans. AIME (1951) 191, p. 174; Journal of Metals (Feb. 1951) TP 3002E. 2 W. Ageew, M. Hansen, and G. Sachs: Decomposition and Changes in Properties of Super-saturated Silver-Copper Alloys. Ztsch. Physik (1930) 66, p. 350. 3W. L. Finlay and W. R. Hibbard, Jr.: Some Effects of Applied Stresses on Precipitation Phenomena. Trans. AIME (1949) 180, p. 255; Metals Technology (Sept.

Jan 1, 1952

By P. A. Beck

ACCORDING to the traditional definition,1 re-x crystallization is a process taking place upon annealing of cold worked metals, characterized by the appearance of new strain-free grains, growing at the expense of the cold worked grains until ultimately the new crystals completely replace the cold worked structure. In metals like brass this process was observed long ago to take place simultaneously with the return of the mechanical properties to those characteristic of well annealed material. The above definition implicitly assumes that the matrix in which the new grains are growing is essentially still in the cold worked condition at the time it is absorbed by the new grains, i.e., that the energy stored in the metal during cold working is not greatly decreased by recovery, prior to recrystallization. Accordingly, the bulk of this energy is assumed to serve as the driving force for the process of recrystallization. Recently, a great deal of evidence accumulated, indicating that the traditional concept may be considerably in error. Suzuki' found that by far the largest portion of the stored energy of cold work in compressed polycrystalline copper is released in the early stages of annealing, well in advance of recrystallization. Thus, the new recrystallized grains are undoubtedly growing in a matrix which is, at least energetically, no longer in the cold worked condition, but has nearly returned to the annealed state. It is true that in Suzuki's experiments the major hardness changes due to annealing were observed to take place concurrently with the formation and growth of the new grains, but this process apparently involved the release of only a minor residual fraction of the stored energy of cold work. Confirming in this respect the views of Wood," several recent investigations by various techniques lead to the conclusion that the grains of many, if not all, metals in the cold worked condition consist of small, slightly disoriented "crystallites" or "sub-grains".* (After appreciable deformation at room temperature, the subgrain size in copper appears to be about 7.104 cm and in high purity aluminum about 2.10-4 cm.) Recent investigations which demonstrated this phenomenon most convincingly are those of Heidenreich8 with hammered high purity aluminum, of P. B. Hirsch and collaborators7,8 with cold worked polycrystalline aluminum, copper, nickel, iron, gold, etc., and of Warren and Averbach9 with a rolled copper plus 2 pct Si single crystal. In addition to the existence of slightly disoriented sub-grains, the cumulative evidence from these investigations also shows that in the cold worked condition the subgrains themselves are severely strained. With regard to the early stages of annealing, Heiden-reich's results indicate that within the subarains of hammered high purity aluminum the strain gradually disappears, without discernible migration of the subboundaries. This recovery process presumably accounts for the major portion of the energy release

Jan 1, 1953

By E. C. Houston

The phosphate ores mined in middle Tennessee typically consist of granular rock phosphate particles disseminated in a clayey matrix. In the TVA plant near Columbia, Tenn., the phosphate ore is mined, made into a slurry with the addition of a small amount of sodium hydroxide as dispersant, and treated in a hydroseparator to remove minus 10 micron material. The hydro-separator underflow, comprising a rough concentrate, is transported by pipeline to the plant; the hydro-separator overflow, comprising a tailing, is flocculated by addition of calcium sulphate and is discharged to settling ponds at a rate of about 1400 gpm. Sedimentation in the ponds produces a clarified effluent, which may be recycled for use as process water or discharged to surface drainage. This method of tailing treatment is not entirely satisfactory since poor sedimentation characteristics of the tailing result in poor ultimate utilization of pond storage volume.

Jan 1, 1949

Z. W. Bartlett, J. C. Carrington, H. C. Petersen and K. T. Price were elected vice-presidents of the Freeport Sulphur Co. Blandford C. Burgess was transferred on January 1 to the new Defense Materials Procurement Agency as strategic materials specialist. In May the Region III headquarters of this organization was moved to London. L. C. Campbell was elected president of National Coal Assn. Mr. Campbell, who has been a member of the National's Board of Directors and Executive Committee for many years, is vice-president of the Coal Div. of the Eastern Gas & Fuel Associates and in charge of their extensive mining operations in West Virginia, Pennsylvania and Kentucky. Vern H. Christoph has been transferred to Panama Canal Co., Marine Bureau, Navigation Division, Port Captains Office, as an admeasurer at Cristobal, Canal Zone. Eugene Cline, recently graduated from the University of Kentucky, has been employed by Pond Creek Pocahontas Coal Co., at Evanston, Ky. Sanford S. Cole, assistant manager of research at the Titanium div. of National Lead Co., received the Alumni Citation from his alma mater, Alfred University, Alfred, N. Y. This was in recognition of outstanding achievements and services in the field of ceramics which have brought honor to the institution. U. K. Custred, recently graduated from University of Kentucky, and may be reached now at Box 87, Monterey, Tenn. Robert E. Dwyer, executive vice-president of Anaconda since 1940, was recently elected president of this company and its subsidiaries, Chile Copper Co., Chile Exploration Co., and Andes Copper Mining Co. As president, Mr. Dwyer succeeds the late William H. Hoover who died in Butte, Mont.

Jan 1, 1952

By Fred N. Kissell, Natesa I. Jayaraman

Introduction This paper describes a recent Bureau of Mines research project that resulted in a simple procedure for reducing the dust exposure of longwall shearer operators. This project involved the development and testing of a water spray and passive shield system to hold dust against the face and away from the shearer operators. This system is known as the Shearer- Clearer.

Jan 1, 1981

By L. S. Darken

THE manufacture and treatment of metals comprises operations whose effectiveness depends in large measure upon diffusion phenomena. The significance of such phenomena has, for a few simple cases, long been understood, but in more complex cases it has not been adequately recognized. This paper presents a mathematical analysis of some of the cases in which diffusion leads to the formation of a new phase within the metal, and this analysis provides a basis for interpreting quantitatively many apparently diverse experimental observations recorded in the literature, some of which are outlined in the following pages. OBSERVATIONS RECORDED IN LITERATURE An outstanding instance is the general type of phenomenon in which diffusion of an element into an alloy is followed by a phase change, which most frequently is a reaction (precipitation) of the diffusing element with one or more components of the alloy to form a compound. Thus in certain alloys heated in contact with oxygen not only the usual oxide scale appears but, in addition, beneath the surface, a well-defined zone in which free oxide particles are dispersed with notable uniformity. This zone, commonly referred to as the subscale or zone of internal oxidation, is remarkable in that the visible boundary between it and the unaltered metal is usually sharp. Such a subscale, which appears to have been recognized first in oxidized copper alloys, has been described and studied by C. S. Smith,1 by Rhines,2 and by Rhines, Johnson and Anderson;3 but it appears also in other alloys when they are exposed to conditions that bring about the precipitation of some compound, not necessarily an oxide. Another clear case of this same kind is the diffusion of carbon into a steel containing an element such as molybdenum, chromium, vanadium or tungsten, whose carbide is less soluble in iron than iron carbide, the result being that some part of that element is precipitated as a dispersed carbide. A similar phenomenon may occur on the welding of two alloys each of which contains one of a pair of elements that react to form a compound or a new phase of any sort. But in addition to the precipitation of a compound formed from the diffusing element, other effects may result merely from the presence of the diffusing element. For instance, if homogeneous austenite, nearly saturated with respect to carbon, is heated in contact with silicon in the absence of oxygen, one would expect to find, behind the several iron-silicon phases analogous to a scale, a zone of austenite containing dispersed carbide, because of the fact that silicon decreases the solubility of carbon in iron. As still another example, oxidation of an alloy may result in diffusion toward the surface of one or more of the constituents; for instance, during oxidation of a steel containing an element such as copper, which is less prone to oxidation than iron, there is a notable enrichment of copper just beneath the scale-metal interface. As an example of a yet more

Jan 1, 1942

By Carl L. Renzoni

INTRODUCTION This paper defines equity as the issuance of a permanent interest in the business on a broadly distributed basis. As such, it excludes the issuance of equity to either a merchant bank or to another corporation. Nearly twenty years ago the equity markets were very simple: The instruments used were primarily common shares, convertible debentures or convertible preferred shares. Another equity-type option often used, especially by junior companies, was the sale of joint venture interests. Issue sizes were generally in the order of $25 - $100 million and issues were syndicated primarily in North America and Europe by one or two investment dealers. Mining corporations today benefit from a market with much more depth. Issues are syndicated by dealers on a truly international basis, and issue sizes now often range up to $300 million. Moreover, dealers are now willing to take significant risk in buying the issues for redistribution. This discussion of trends in equity markets will encompass: 1) common shares 2) warrants to buy common shares 3) convertible debentures 4) commodity backed instruments A review follows of events that affect the mining industry and investment dealers as they have a bearing on the equity markets for the metal producers. FACTORS AFFECTING THE MINING INDUSTRY The current business cycle, up to October 1987, had been characterised by a buoyant stock market and depressed base metal prices. Mining companies entered this period with weak balance sheets and little prospect of cash flows meeting capital needs. The issuance of equity and the sale of assets were used extensively to reduce debt to manageable levels. During this period, the relative high price for gold, and more important, the very high earnings and cash flow multiples afforded to gold producers, caused companies to target gold as the only game in town. The need for capital to acquire and develop gold properties prompted an unprecedented volume of equity issues. (Burns Fry led or co-managed over $1 billion of mining equity issues per year during this period). This high demand for equity capital by the industry prompted an increase in the use of equity instruments, such as commodity backed instruments. In addition, government tax incentive programs in Canada, such as flow-through shares, allowed smaller companies to raise significantly more equity than would otherwise have been possible. Over $1 billion in flow-through equity was raised in 1987 alone. The abundance of flow-through capital in Canada made it easy to form a new company. One flow-through share fund developed a system of providing the working capital required for a company to be eligible to receive flow-through share capital so that an entrepreneur required only a mining property to get started. Many new companies were formed and several flourished in a buoyant stock market environment to the point that market capitalizations grew to $100 million or more. The current period is in stark contrast to that before October 1987. The equity markets are generally available to the resource industry only on a window basis and only for senior companies and for special situations. The industry is benefitting from buoyant metal prices, and bankers are anxious to provide debt capital. Investment dealers previously processing several equity issues

Jan 1, 1990

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby