Search Documents

By J. E. Schaffer

Drilling activity in Ohio increased slightly in 1939. There were 1020 completions as compared to 910 in 1938. During the past six years the number of completions has varied little (Table 1). Oil production in Ohio has been gradually declining since 1896, when the peak production of 23,941,000 bbl. was reached (Fig. 1). Since that date production has slowly declined to an estimated production in 1939 of 3,144,134 bbl., the lowest in 53 years. This total production is divided approximately into the following grades of crude oil: Pennsylvania, 1,185,456 bbl.; Corning, 1,261,615 Flg 1. bbl.; Lima, 578,500 bbl.; Lodi, Based on figures of U. S. .Bureau of 104,740 bbl.; Cleveland, 13,823 Mines and Oil andGas Journal bbl. Table 2 shows the prices paid for the various grades of crude oil.

Jan 1, 1940

By Edward Saibel

The object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. Theory op Fracture In the thermodynamic theory of the fracture of metals developed earlier,' it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form « ± u. = JLJW/V [r] where L, is the latent heat of melting of the unit volume, AV/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, uo is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will he assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. I. If the point of intersection of the straight line with the axis of zero strain is represented by v., and the slope of the straight line is p, the analytic form of the flow curve is a = (To + pd [2] and the strain energy per unit volume evaluated from Jud6 becomes (u,6 + pa2/2). When this latter term reaches the critical value JLbVIV (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: a; = V«r.2 + iMp [3] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. Flow and Fracture Curves LudwigZ attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1948

By Edward Saibel

The object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. Theory op Fracture In the thermodynamic theory of the fracture of metals developed earlier,' it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form « ± u. = JLJW/V [r] where L, is the latent heat of melting of the unit volume, AV/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, uo is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will he assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. I. If the point of intersection of the straight line with the axis of zero strain is represented by v., and the slope of the straight line is p, the analytic form of the flow curve is a = (To + pd [2] and the strain energy per unit volume evaluated from Jud6 becomes (u,6 + pa2/2). When this latter term reaches the critical value JLbVIV (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: a; = V«r.2 + iMp [3] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. Flow and Fracture Curves LudwigZ attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1948

By J. N. Maycock, P. W. M. Jacobs

Previous measurements of the thermoelectric power of ionic crystals are reviewed briefly. It is concluded that, while extensive measurerements are available on systems in which the electrode M has a cation in cornon with the sall MX, there is as yet little modern work on systems in which the metal electrode M' does not haue a calion in common with the salt. We haue now measured the thermoelectric power of- single cryslals of KC1 and of KC1 + SrCl2 between plati.nu?n electrodes over a much wider range of temperature than before. individual ionic heats of transport, which, while probably not very accurate, are of a reasonable order of magnitude, are obtained from this data on the basis of an assumption that charge carriers do not cross the electrode/salt interface. RELATIVELY little work has been done on thermal diffusion in ionic crystals. Reinhold and coworkers1-I measured the thermoelectric power and Soret effect in silver and cuprous salts and their mixed crystals. One electrode was kept at constant temperature and electromotive force was measured as a function of the temperature gradient. This is not a satisfactory technique if the results are to be compared with theory; rather should the electromotive force be measured for small temperature differences as a function of the mean temperature of the two electrodes. They used electrodes having the same cation as the salt. Patrick and Lawsons measured the thermoelectric power of AgBr and of AgBr containing 0.25 mole pct CdBr2 using silver electrodes and temperature gradients of 10°C in the temperature range 100° to 400°C. The results were analyzed using the Teltow9 values of the ratio of the mobility of the two types of charge carrier (cation vacancies and interstitials) found from conductance measurements and the wagnerlo estimate of the heterogeneous contribution to the thermopower, Ohet They obtained values of qi = 0.017 ev and q$ = -0.385 ev for the heats of transport of interstitial Ag ions and cation vacancies, respectively. Their data has been reanalyzed by Haga using the corrections to the Wagner formula for ehet given by Howard andLidiard; Haga found ev. Christy et a1.14 have measured the thermopower of AgBr containing 0.01 to 1.0 mole pct CdBr,. They analyzed their results in terms of the theory of Howard and Lidiard and found that excellent agreement with the theory was obtained if q5 + : + hF was set equal to 0.70 ev at 175°C and equal to 0.58 ev at 250°C. Since Teltow's value for hF, the enthalpy of formation of a Frenkel defect pair, is 1.27 ev, this means that qt + q: increases in magnitude from -0.57 ev at 175°C to -0.69 ev at 250°C. This result is in poor agreement with Patrick and Lawson's value of -0.37 ev for pure AgBr (for which the corrections to the Wagner estimate for ehet are very small). christy1' has also reported thermopower measurements for pure silver halides and for the systems he finds that qr + qt for AgBr increases in magnitude from about -0.55 ev at 150°C to about -1.1 ev at 400°C. The temperature dependence of the sum of the heats of transport in AgCl is very similar in magnitude. The sum qi + q cannot be decomposed into the individual interstitial and vacancy heats of transport without a knowledge of the entropy contribution from the change in the lattice vibrational frequencies around the interstitial and vacancy. Despite this it seems an inescapable conclusion from Christy's analysis that and -6 = Q Ag are quite strongly temperature-de pendent and that -q: is much greater in magnitude than the corresponding activation energy for vacancy migration, +0.37 ev. It remains a mystery as to why the data for pure AgBr are fitted so well by the assumption of temperature-independent heats of transport if association of impurity ions and vacancies is neglected.l The values for q$ and q: so obtained are also much more in line with those expected from a simple kinetic interpretation of the heats of transport due to wirtz.17 Christy and Hsueh have also measured the thermopower of CuCl between copper electrodes; 0 for pure CuCl is comparable with that for the silver halides but, owing to the limited solubility of divalent cation impurities it was not found possible to deduce values for the heats of transport. In contrast to these extensive measurements on cells of the type M MX 1 M, there have been relatively few attempts to measure the thermoelectric power of cells of the form M' 1 MX I M'. (We specifically exclude from discussion cells of this type in which the metal electrodes M' are in contact with gas containing a controlled partial pressure of either M or X,, since in these cells the electrochemical reactions are analogous to those of the first type.) The thermoelectric power of Pb12, PbC12, TlC1, TlBr, TlI, NaNO3, and KNO 3 between platinum electrodes was measured by Thie1e.l3 In discussing these measurements Holtan20 asserts that the thermopotential initially fluctuated wildly and even changed sign before approaching a steady value. A high degree of irreproducibility is also evident in the work of Nikitinskaya and Murin21 who first studied the thermopower of NaCl and KC1 between platinum electrodes. Much better reproduci-bility was achieved in our earlier measurements on KC1;22 these were, however, confined to a relatively narrow temperature range and one of the objects of the work reported in this paper was to extend the temperature range of the measurements of the thermoelectric power 8 of KC1. The only other published

Jan 1, 1967

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

By J. A. Grimes, Paul Billingsley

A. Introduction. 1. Association of Ores and Igneous Rocks. 2. Identity of Granite Rocks. B. General Geology. 1. Geologic Events of the Igneous Cycle. 2. Association of Igneous Intrusions with Tectonic Forces. C. Igneous Rocks. 1. Andesite Period. 2. Granite Period. (a) Diorite. (b) Quartz-Monzonite. (c) Aplite. (d) Quartz-Porphyry. (c) Quartz-Veins. 3. Rhyolite Period. 4. Comparative Analyses. D. Classification of Deposits. 1. Genetic Classification. 2. Parallelism Between Igneous Stages and Stages of Ore Deposition. Part 2.—The Ore Deposits Andesite Period. A. Andesite Phase. 1. Disseminations—Baggs Creek. 2. Contact Deposits—Iron Mines of Ekhorn Mountains. 3. Fissure Veins—Emery District. (a) Fissure Veins in Andesite Walls. (b) Mineralization Along Bedding of Flows. (c) Mineralization of Amygdaloidal Lavas. (d) Mineralization of Breccia. 4. Summary.

Jan 1, 1918

By Nicholas J. Grant, Hanna Ibach, Bill C. Giessen

The system Ta-Rh was investigated over the entire comnposition range using metallogvaphic and X-ray techniques as well as thermal analysis. Terminal solubility limits, solidus temperatures, and the crystal structures of two new intermediate phases were determined. There are five intermediate phases: o, tetragonal, isostructural with o(Fe-Cr); a1, orthorhomnbic : a2, orthorhombic, isostructural with CozSi; 0 3, a high -temperature phase of unknozun structure; and a TaRh3, cubic, AuCu3 structure. a, aL, a,, and a melt peritectically; and a TaRh, has a maximum melting point. Five peritectic and one eutectic reactions occur. THE Ta-Rh phase diagram has not been fully treated in the literature; however, two inter metallic phases have been described.&apos;-&apos; This study attempts to work out the diagram covering the details of phase boundaries as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by National Research Corp., Cambridge, Mass., and rhodium powder of 99.9 pct purity, supplied by Bishop Co., Malvern, Pa. Analyses as given by the manufacturers are presented in Table I. In addition to the spectroscopic analysis, an oxygen analysis has been made of the tantalum powder. After preliminary trials, the standard procedure employed in making the alloys was as follows (see Ref. 4 for further details). The powders were weighed, mixed manually, compacted under 16,000 psi, and arc-melted at not more than 500 amp under thoroughly titanium gettered welding-grade argon of 400 mm Hg pressure. The gettering process was repeated after each melt. It had been shown previously5 that under these conditions no oxygen pick-up exceeding 0.001 pct in a hafnium button could be detected. The buttons, ranging from 5 to 10 g in weight, were inverted or, if possible, crushed and remelted three times. Melting presented no difficulty, except for tantalum-rich al- loys, which showed considerable spashing during melting. The average weight loss of 1 wt pct rose to 2.5 wt pct in these cases. Subsequent melting, however, resulted in losses of less than 0.1 wt pct. The melts obtained frequently showed small in-homogeneities, mostly in the tantalum-rich part of the system below 25 at. pct Rh. This was not due to insufficient blending of the elements, but to crystallization taking place from the cooled bottom. This condition was not improved by further re-melting; therefore the following precautions were taken. Cross sections of as-cast buttons were made. For the investigation only buttons were used where these inhomogeneities did not exceed 1 at. pct (estimated from the amounts of haSeS resent). In addition, only the center portions of such buttdns were utilized to minimize errors. Smaller buttons showed smaller concentration gradients and were used as a check. Finally, all alloys were homogenized to eliminate coring (see below). After this, the error in alloy composition due to inhomogeneity was cl at. pct. In order to confirm the concentrations of the alloys and to provide an impurity check, wet-chemical analyses and oxygen-fusion analyses of four key alloys were carried out. The results, together with the concentrations as calculated with the weight balance method, are presented in Table 11. It was found that for three alloys the agreement is very good (< 0.2

Jan 1, 1964

By M. H. Childs, K. E. Merklin

Blast furnace feed specifications are being revolutionized because of the large increase in iron pellet production from low-grade ores of the Lake Superior region. Recent laboratory findings aimed at a better understanding of factors influencing the physical quality of pellets produced from taconite concentrates are reviewed. Tests for determining better product quality, the effects of additives, and production factors are discussed. The current revolution in specifications for blast furnace feed is typified to a great extent by the recent tremendous growth in iron ore pellet production from low grade ores of the Lake Superior region. Indeed, pellets are responsible, at least in part, for many of the stringent new requirements that are being placed on the suppliers of furnace raw materials. As the tonnage of pellets going to the steel mills increases, more and more attention is being turned to the detailed characteristics that make this product an ideal blast furnace feed. Control of quality in pellets is similar to that of any other product. A basic understanding of the factors that are encountered in their production, from the crude ore through to the finished product, is required, along with careful process supervision and frequent quality checks. Normally, chemical grade is not a problem. This usually can be controlled within the desired specifications by minor operating variations in the con- centrator. While future changes in requirements may result in the need for self-fluxing pellets1 or other chemical changes, today&apos;s quality demands center primarily around the physical characteristics of the pellets. It is in this area that many of the recent laboratory studies have proven helpful to the operating plants. A better understanding of the physical factors involved in pelletizing has provided the basis for a continuing program of quality improvement. Tigerschiold and Ilmoni2 and Cooke with various associates are responsible for the development of much of the basic understanding of the pelletiz-ing process. These earlier findings have served as a most useful background for this work. LABORATORY PROCEDURES Magnetite concentrates produced from eastern Mesabi Range magnetic taconites were used for all of the work reported herein. The sizing and chemical analysis of a random sample are shown in Table t Additives usually are mixed with the concentrates in taconite plants before pelletizing to improve the strength characteristics of the unfired balls. Ben-tonite, soda ash, and coal are in common use. The bentonite used in these studies was of the Wyoming sodium type; the soda ash was a standard commercia1 brand. Anthrafines were used where coal was called for. The procedure for making batches of balls at the Hibbing Laboratory is as follows: In an especially designed mulling equipment 2800 g of dry ore are mixed for 10 min with the desired additives. Water is added and mixing continued for 1 1/2 min. The charge is removed from the muller and put through a mechanical shredder to break down any lumps that may have formed. sixty previously formed seed balls are placed in the balling drum, which is in fact a 6 x 16-in. diam airplane tire turning at 53 Wm. Two thousand grams of the shredded concentrate and additive mix are fed by hand into the tire at a con-

Jan 1, 1961

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler&apos;s saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By L. S. Darken

A quadratic formalism is developed lor the representation of the excess free energy, and of the activity coefficients of each component of a ternary system in the vicinity of a single component selected as solvent. This formalism, in contrast to the e formalism, is thermodynamically consistent at .finite concentrations. Numerous specific systems are used as illustrations, with cross checks where possible; these systems are Fe-C-X systems in the vicinity of 1600°C and include practically all those for which reliable data are available. It is shown that this formalism is usually quite adequate to rebresent available data up to a solute concentration of 20 to 30 at. pet. It is hoped that the formalism here presented may prove useful for the treatment and tabulation of data on ternary and multi-component solutions. SINCE, as discussed in a prior paper,&apos; we do not as yet have an adequate basic understanding of the nature of binary metallic solutions, we cannot hope to be in better position for ternary and multicomponent systems. However, the accumulation of thermodynamic data on ternary and multicomponent metallic solutions has led to an urgent need for a rational formalism for the presentation and use of such data. Notable attempts to represent the isothermal isobaric thermodynamics of ternary solutions were made by Benedict et 01.&apos; and by Wohl.3 These attempts were directed toward developing an analytic expression adequate to encompass the entire ternary triangle, primarily for organic systems; they generally involve the power-series approach, which has been shown&apos; to be inappropriate, in general, even for binary metallic systems. On the other hand, interest in the thermodynamics of ternary and multicomponent metallic solutions has tended to focus either on general thermodynamic relations4-10 over wide compositional ranges, or on cases where one or more components have been at rather low concentration. This latter approach has been followed by Wagner,= by chipman,11 and by Alcock and Richardson,12 and more recently in many publications by the same and other authors. It has already been shown&apos; that the thermodynamic behavior of binary metallic systems is, in general, relatively simple only in the terminal regions. Hence, it would appear that any approach, at this time, to a simple formalism for ternary and multicomponent systems must, a fortiori, be limited to the vicinity of the major component or solvent. The present treatment is aimed to be useful for a given solvent with moderate solute concentrations ranging up to 20 or 25 at. pet and in exceptional cases to considerably higher concentrations. In order to achieve even this modest objective, it is necessary that any appropriate formalism have built into it 1) a thermodynamic consistency (at least within the desired degree of approximation), and 2) an approach at infinite dilution to Raoult&apos;s law for the solvent and to Henry&apos;s law for each solute. Let us first formulate the condition of thermodynamic consistency for a ternary system. Under isothermal isobaric conditions, we may write for the molal value G of any extensive function dG - C1 dN1 + G2 dN2 + G3 dN3 [l] where the G&apos;s are the corresponding partial molal quantities and the N&apos;s are the atom fractions. Taking component 1 as the solvent, this relation may be rewritten in terms of the independent variables N2 and N3

Jan 1, 1968

By F. D. Rosi, C. A. Dube, B. H. Alexander

WHEN a deformed polpcrystalline metal is heated to a sufficiently high temperature, a recrystallized structure develops which consists of small, essentially stress-free grains. This transformation is referred to as primary recrystallization. Under certain conditions, on prolonged annealing of the specimens, a type of grain coarsening occurs in which a small number of grains commence to grow at various points by devouring the neighboring finegrained primary structure, which, in itself, exhibits a marked stability toward normal grain growth. This grain coarsening process has been referred to by Burgers&apos; as "secondary recrystallization" or "exaggerated grain growth." Although much work has been done on recrystallization and growth processes, present knowledge of the factors which determine the occurrence and growth of secondary grains is inadequate for the advancement of a theory which accounts for the observed characteristics of this recrystallization phenomenon. In this respect, it would be important to make measurements of the velocity of growth of these large secondary grains. The early work of Feitnecht2 on aluminum showed that the size of secondary grains increased with temperature and time, suggesting that such measurements would be possible. More recently, Burgers1 found that the growth velocity of these grains in aluminum was constant over a large time interval, as is generally found for the growth velocity of primary grains in a uniformly deformed test piece.3-5 It is reasonable to expect that the determination of the activation energy of the secondary growth process might lead to a better understanding of the underlying atomic mechanism. This investigation, therefore, is one of a series primarily designed to measure the growth velocity of secondary grains at various temperatures for silver, copper, and aluminum. It is hoped that these studies along with those of orientation relationships, will establish a sound basis for theorizing as to the origin and nature of the secondary transformation. Experimental Procedure The metal used in the present investigation was high-purity silver (999.9 fine), which was supplied in the form of cold-rolled plates 0.250 in. thick. These plates were annealed at 500°C for 1 hr and then straight-rolled to a thickness of 0.04 in. in three reductions of approximately 45 pct, followed in each case by an anneal at 450°C for 1/2 hr. The 0.04 in. sheets were given a final reduction of approximately 50 pct, which resulted in a thickness of 0.02 in., thereby insuring two-dimensional crystal growth. Individual specimens of this material about 1x3 cm were used for all heat treatments, unless otherwise noted. The annealing was carried out under an atmosphere of argon in an Inconel tube furnace whose temperature was controlled to within -+2°C. Metallographic examination of the secondary transformation was accomplished by mechanically polishing the specimens on one side to approximately one half their thickness through 2/0 metallographic emery paper, and then electrolytically polishing in a solution of potassium ferrocyanide and sodium cyanide. With a current density of approximately 20 amp per sq dm, the time required to obtain a satisfactory surface varied from 3 to 5 min. Standard potassium bichromate was used to etch the electrolytically polished surfaces. A heavy etch with this solution produced a sharp contrast between the secondary grains and the fine-grained primary structure, darkening the latter while leaving the large secondary grains bright. All area measurements of the secondary crystals were made with a planimeter on enlarged tracings of the grains.

Jan 1, 1953

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a&apos; range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.&apos;

Jan 1, 1955

By John P. Huger

me phase diagram for the system Ag-Si has been established by thermal analysis. The diagram is a simple eutectic type with a eutectic at 3.0 pct Si and 840°C. From the liquidus curve and with the aid of regular solution theory, the thermodynamic properties of the liquid Ag-Si system at 1420 °C have been determined. Silicon exhibits positive deviations from Raoultain behavior at all compositions, while silver exhibits both positive and negative deviations. MEASUREMENTS of silicon activities in liquid iron alloys by means of distribution studies between the immiscible liquids silver and iron have been reported by Chipman, Fulton, Gokcen, and caskey.&apos; The applicability of this technique is dependent, however, on the accuracy of the silicon activity values in the Ag-Si alloys, particularly in the dilute silicon region. Darken and Gurry2 have shown that log ?si/(1-xSi)2 is approximately linear with composition, but uncertainty exists in the extrapolation to dilute solutions. Their calculations are based on the old Ag-Si phase diagram of Arrivaut3 and any variation in the position of the liquidus curves will strongly influence the extrapolation. The purpose of this study is to redetermine the Ag-Si phase diagram and calculate the associated thermodynamic properties. EXPERIMENTAL The Ag-Si phase diagram was determined by thermal analysis of liquid alloys. The alloys were contained in a 35 mm alumina crucible under a protective stream of purified argon. The crucible was placed inside a 64 mm alumina tube fitted with a gas-tight, water-cooled, copper head. The tube and assembly were heated in a manually controlled globar furnace. The temperature was measured with a Pt, Pt + 10 pct Rh thermocouple in a high-temperature porcelain protection tube. The thermocouple calibration4 was checked against the melting point of pure silver at the start and during the course of the experiments, and against both gold and silver at the completion of the experiments. The alloys were prepared from granular silver analyzing 99.95 pct Ag and powdered silicon analyzing 99.88 pct Si and 0.026 pct Fe. Approximately 150 g of alloy were used for each run. The composition of the alloy was determined by withdrawing samples of the liquid alloy with a vycor tube-aspirator bulb device. Analysis of solidified samples agreed, for alloys containing less than 23 pct Si, within ±0.3 pct Si of the calculated composition. Duplicate samples showed a variance within 50.05 pct Si of the mean analysis. The alloy was heated to 100&apos; to 20pC above the estimated liquidus temperature and then the furnace was adjusted to give an average cooling rate of 2" to 7°C per min. A cooling curve was obtained by taking potentiometer readings at 15-sec intervals. Several analyses were made by recording the thermocouple output on a high-speed, Stip-chart recorder, with the exception of run NO. 11, a minimum of two thermal analyses were made for each alloy and the cooling curves then obtained duplicated the liquidus and eutectic temperatures to about 1°C. RESULTS The results of the thermal analysis are given in Table 1, and are represented as the Ag-Si phase dlagram, Fig. 1. The eutectic composition was found

Jan 1, 1963

By P. R. Swann, J. G. Parr

Quenched structures were studied in alloys containing up to 12.5 pct cobalt. The subsequent decomposition of a 10 pct cobalt retained-ß phase alloy was investigated using metallographic and X-ray diffraction methods. Hardness measurements also were made during the decomposition process. Precipitation of Ti2Co is by nucleation and growth; and an activation energy of 50,000 cal per mole was determined. The values of the coefficient ß suggest that the precipitate is pearlitic at temperatures between 450 and 475°C, and spheroidal between 500 and 525°C. THIS paper describes part of a series of invesligations into phase transformations in binary alloys of titanium with transition elements. The general approach is similar to that taken in work on titanium-iron and titanium-nickel alloys.&apos; Previous investigators&apos;&apos; have established the titanium-rich end of the titanium-cobalt phase diagram, reproduced in Fig. 1. Orrell and Fontana&apos; showed that alloys containing more than about 6 pct" cobalt quenched from the ß range, produced 100 pcl retained-p phase. The isothermal decomposition of alloys containing between 0.8 pct Co and 15.5 pct CO was investigated by the same workers in the temperature range 650 to 1000°C. They reported that these alloys transformed into a or Ti,Co depending on the cobalt content, but no quantitative data were given. In the work to be described a series of alloys containing 0.8 pct Co to 12.5 pct Co was examined in the quenched condition. The 10 pct Co alloy (the lowest cobalt content to retain 100 pct ß on quenching) was selected for further work on the tempering kinetics of the ß decomposition. Experimental Procedure Since our own melting equipment was not installed at the outset of this work, the Physical Metallurgy Division of the Department of Mines and Technical Surveys (Ottawa, Canada) prepared the alloys. These were made of Japanese sponge, (which when melted had a value of 103 DPH, using a 1-kg load), and electrolytically prepared cobalt. The al- loys, made up to contain 0.8, 1.6, 3.3, 5.8, 8.3, 10.0 and 12.5 pct Co, were homogenized by swaging into rods at 900°C. Filings were taken from the rods, and any iron chips from the file were separated magnetically. Size fractions of both plus and minus 200 mesh (about 75p) were shown by their constitution, after annealing just below the eutectoid temperature, to contain the same cobalt content. Consequently, it was permissible to use the —200-mesh fraction, knowing it to be representative of the rod composition. Quenching in argon was carried out in a newly designed furnace, whose features include (1) an Inconel furnace tube, (2) a positive pressure of argon maintained at all times in the furnace—even when a sample is removed or inserted. The furnace is shown in Fig. 2 and is described in the Appendix. The tempering processes were carried out on powder samples sealed in evacuated quartz capsules. Since the highest tempering temperature was 525OC, no protection against reaction with the quartz was necessary. (Tests were made on filings of iodide titanium and showed no hardness increase after equivalent heat-treatments.) A thermocouple was attached to the capsule, which was heated to the

Jan 1, 1959

By M. P. E. Desvaux, P. Charsley

OLIP-line observations on copper alloys, using the electron microscope, have been made by a number of workers,13 but this work has been confined to a brass. In a CuAl alloys Koppenaal4 and Koppenaal and Fine5 have made observations with the optical microscope and by the use of interferometry. They found that the observed slip step heights inside the Liiders bands accounted for only 42 pet of the total macroscopic strain. The suggestion was put forward that optically unresolvable slip in other parts of the specimen accounted for a major part of the macroscopic strain. This is surprising since it is known from other workers that slip in a brass is inhomogeneous; i.e., large amounts of slip occur on individual {lll) closelys paced than being shared by a large number of closely spaced planes. Furthermore, a brass and a CuAl alloys with high concentration of aluminum exhibit similar deformation characteristics and slip-line patterns. Prior to investigations into the behavior of copper and a CuAl alloys under reversed stresses in tension and compression, some preliminary experiments have yielded results which the authors think resolve this discrepancy, and throw some further light on the behavior of a CuAl in tension. An experiment was carried out on a 10 at. pet CuAl single crystal, of gage length 7.5 cm, diameter 3.1 mm, and orientation shown in Fig. 3 (inset), for the purpose of resolving the above discrepancy. The specimen gage length was electropolished for 10 min in a 50:50 orthophosphoric acid (SG=1.75)-distilled water system, with 2 v across the cell and a current density of 0.5 amp per sq cm. The cathode was made of copper. After a tensile strain of 0.067 ± 0.001, intense slip was observed over a length 2 cm of the gage length whilst the rest of the specimen was relatively undeformed. In the lightly deformed region, slip bands of mean width 20 /x were spaced about 1 mm apart on average. The transition from the heavily slipped region (usually called a Liiders band) to the lightly deformed region was gradual, the slip-band density increasing as the "Liiders band" was approached. In the latter, the slip bands became so close together that, to the naked eye, the specimen appeared to be continously slipped, and the typical microtopography of this region is shown in Fig. 1. Twelve electron micrographs were taken at random from replicas of the Liiders-band region, and the widths of the slip lines were measured. The slip lines account for an over-all tensile deformation of 7.0 ± 0.7 pet, after allowing for the lengths of the un-slipped regions, which is in good agreement with the macroscopic strain. The distribution of slip-line widths was also measured and is shown in Fig. 3. Since Koppenaal could not resolve slip lines with height less than 540A (limit of resolution represented by dashed line), then it was deduced that he could have measured only about 50 pet of the deformation within the &apos;Liiders Band&apos;. It is concluded, contrary to the suggestion of Koppenaal,5 that virtually all the macroscopic strain is accommodated within the "Luders band" and that there is no need to invoke fine slip distributed uniformly over the gage length.

Jan 1, 1967

By T. R. Ingraham

The thermal decomposition of cupric sulfate and of cupric oxysulfate has been examined by deter-mining the equilibrium gas pressure generated over each pure compound. The equilibrium data have been used to calculate the thermodynamic properties of both compounds, and the results have been combined with previously published data to establish a predominance-volume diagram for the Cu-S-O system over the normal range of roasting temperature and gas composition used in the treatment of copper minerals. Copper oxysulfate recrystal-lizes at 1100°K with an apparently irreversible en-dothermic heat requirement of 2.9 * 0.3 kcal per mole. WHEN mixed sulfide minerals containing copper are roasted, either of two procedures may be followed, depending on the nature of the other metals. In the first procedure, the roasting is controlled to produce a maximum amount of water-soluble copper sulfate which may be removed selectively from the water-insoluble compounds of the other metals. In the second, control is directed toward the production of water-soluble sulfates of the other metals and an insoluble salt of copper. Effective control of either of these processes would be enhanced by knowledge of the thermal stability of cupric sulfate and of cupric oxysulfate. In this paper, established data for the thermal stability of cuprous and cupric sulfide and of cuprous and cupric oxide will be combined with new data for the therma1 stability of cupric sulfate and cupric oxysulfate, to designate the volumes of stability of the significant compounds in the Cu-S-O system in the temperature range 750° to 950°K. EXPERIMENTAL Materials, Apparatus, and Procedure. The copper source material used in all experiments was Fisher Certified Reagent Grade "anhydrous" cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared from the normal sulfate by two procedures. In the first, equimolar quantities of cupric oxide (prepared by decomposition of the sulfate) and cupric sulfate were ground together and heated under vacuum in a sealed silica vessel at 800°C. This procedure was subject to failure because of explosion of the silica vessels due to the pressure of the final traces of water released from the sulfate on the initiation of its decomposition. The second procedure involved roasting the cupric sulfate, with frequent rabbling, in a muffle furnace at 725°C for a period of 48 hr. This produced an excellent product, which was confirmed as copper oxysulfate by X-ray and chemical analyses. The experimental technique used was that of measuring the total pressure exerted by the sulfur trioxide, sulfur dioxide, and oxygen produced by the following reactions: 2 CuS04 = cuo • CuSO4 + SO3 [1] cuo . CuSO4 = 2 cuo + SO3 [2] SO3= SO2 + 1/2 O2 [3] The apparatus used in the experiments has been described previously.1-3 Its main feature of a U-tube mercury manometer in which the mercury is protected from corrosion by enclosure in a flexible Pyrex bellows. Before beginning a run, the interior of the apparatus, including the bellows-manometer and all connecting tubing, was thoroughly washed with hydrochloric acid and distilled water to remove any

Jan 1, 1965

By R. E. Carter, C. Wagner, F. D. Richardson

By means of inert markers of radio-platinum, it has been shown that cobalt metal oxidizes by out-ward diffusion of cobalt atoms through the oxide. Oxidation rates have been measured at various temperatures and oxygen pressures and have been found to agree with the rates calculated from the Wagner equation and the authors&apos; values for the diffusion coefficient of cobalt in the oxide. The distribution of radio-cobalt in growing oxide loyers has been accurately measured and found to be different from that predicted from the Wagner oxidation theory. Attempts have been made to measure the change of lattice parameter of the oxide with composition. SEVERAL investigators have shown that cobalt metal oxidizes according to the parabolic law,1-3 but no detailed study has been made of the oxidation mechanism. Cobaltous oxide has a metal-deficient lattice, but the defect concentration which is dependent on the oxygen pressure is only approximately known.&apos; From the similarities in the structures of "CoO" and "FeO" and the rate laws governing the oxidation of cobalt and iron, Gulbransen- as suggested that cobalt, like iron," oxidizes by diffusion of cobaltous ions through the oxide layer. To substantiate this hypothesis, he has attempted to measure the oxidation rate of cobalt as a function of the oxygen pressure but has been able to report only that the rate depends on a "small" power of the pressure. On the other hand, Preece," Valensi,&apos; and Arkharov&apos; all have suggested from indirect evidence that oxygen diffuses through the COO to the metal-oxide interface. The present authors, in a previous paper,&apos; have shown that the rate of diffusion of cobalt in cobaltous oxide is dependent on the oxygen pressure. In that investigation, they also found that cobaltous oxide disks made by complete oxidation of cobalt metal were porous at their centers (Fig. 5L, ref. 4). Both these facts strongly suggest that oxidation of the metal proceeds via outward diffusion of cations. In order to establish the mechanism unequivocally, oxidation experiments were made with inert radioactive platinum markers, and the dependence of oxidation rate on oxygen pressure was measured. In addition, an attempt was made to determine the form of the cation vacancy gradient, which the marker experiment showed must exist across a growing oxide layer. This was done by depositing radioactive Co on the surface of a cobalt disk and then measuring the tracer distribution across the oxide layer produced by partial oxidation of the metal. Finally, an X-ray examination was made in an attempt to find the expected change of lattice parameter of COO with oxygen pressure. Experimental The apparatus and materials used were substantially the same as those previously described by the authors.4 Marker Studies: The use of inert markers to follow oxidation reactions was first attempted by Pfeil" in 1929, and radioactive markers have recently been used by Davies et al.&apos; In the investigation reported here, the markers were applied as an (NH4)2PtCI6 slurry in several thin streaks across both faces of four disks of cobalt metal 1 mm thick and 14 mm in diameter. The disks were then oxidized almost to completion at 1200°C in pure oxygen. After oxidation, they were mounted and sectioned and auto-radiographs were taken to locate the markers. Oxidation Rate: The oxidation rate of cobalt was measured at 1148°C at oxygen pressures ranging from 0.0055 to 1.0 atm and at 1000°, 1148", and 1350°C under 1 atm of oxygen. The rate was deter-

Jan 1, 1956

By C. S. Barrett, D. B. Masson

Martensitic transformations have been found in AgCd both upon cold-working at room temperature and cooling to lower temperatures. The crystal structures of the transformation products were found to be close-packed hexagonal in the first case and or-thorhombic in the latter. The transformation characteristics also were studied. Similar treatment of AuZn alloys failed to yield any transformation. THE literature on martensitic transformations of body-centered cubic metals and alloys indicates widespread instability of this structure at low temperatures, a tendency which merits further study. The body-centered cubic ß-phase of CuZn, for example, when it contained less than 42 wt pct Zn, was found by Greninger and Mooradian&apos; and others&apos; to transform on cooling to subzero temperatures to a phase that was tentatively considered to be tetragonal. Further work by Massalski and Barrett" demonstrated that cold work at low temperatures causes a partial transformation of ß CuZn of higher Zn content. The structures of the strain-induced transformation products were found to be different from those induced by simple cooling. Another well-known martensitic transformation among body-centered cubic phases is that of ß AuCd, first studied with X-rays by Olander,&apos; then very thoroughly by Chang and Read.5,6 Here again transformation was found to occur both as a result of cooling and of strain. The alkali metals Li and Na, as well as certain Li-Mg alloys, also undergo transformation from their normal body-centered cubic structure, both on cooling and on cold-working. The phase AgCd, the subject of the present report, should be expected to behave quite similarly to CuZn for a number of reasons. It is the chemical analogue of CuZn, silver being directly below copper and cadmium directly below zinc in the periodic table. The size factors (percent difference in size) of the atoms, possibly a consideration in the stability of the ß-phases, are +3.1 in AgCd and + 4.2 in CuZn. Likewise the relative electronegativities of the two pairs of metals are about the same, CuZn possessing an electronegativity difference of 1.0 and AgCd one of 0.8. These values are from a table of electronegativities given by Darken and Gurry." The phase diagrams of the two systems around 50 atomic percent are similar, both possessing a disordered body-centered cubic phase, ß, at high temperatures and an ordered bcc phase, ß, at room temperature; however, the ß and ß&apos; phases of AgCd are separated by a hexagonal phase, [, stable in the range 220-440oC, which has no analogue in CuZn. There has been confusion in the literature as to the structures of the ß&apos; and [-phases. The phase diagram in the ASM handbook&apos;" has the structures of the two phases interchanged; however, Hansen" reports the correct relative positions and Muldawer" verified that ß&apos;, the low-temperature phase, is body-centered cubic. Work by the present authors also

Jan 1, 1959

By W. A. Stickney, J. W. Town

Tests demonstrated that aqueous solutions of sodiu~n sulfide would dissolve over 95 pct of the cinnabal- in 5 pct Hg flrotation concentrates and 60 to 90 pct of the cinnabav in low-grade ol-es. Double-leach tests showed that potassiutn sulfide would dissolve 90 pct of the avsenic sulfide in Hg-As satnples and only 1 to 10 pct of the Hg; the sodium sulfide would then dissolve 80 to 90 pct of the rernaining Hg and 30 to 70 pct of the vemaining As. 1 HIS paper describes the extraction, by alkaline sulfide solutions, of mercury from cinnabar-bear ing ores and flotation concentrates. Leaching time and solution temperature had minor effects on mercury extraction when compared to the effects of reagent quantity and ore type and grade. Cinnabar, although readily soluble in sodium sulfide, was only partially soluble in potassium sulfide and essentially insoluble in ammonium sulfide. A double leach process was developed to extract selectively the arsenic from Hg-As products with K2S and to treat the residue with sodium sulfide-hydroxide solutions to extract the mercury.&apos; Mercury was then recovered from the pregnant solutions either by precipitation with metallic aluminum or by electrodeposition. The solubility of HgS in alkaline sulfide solutions was first reported by Volhard in 1878.&apos; The first reported commercial application was made in 1915 when Thornhill applied the method to the treatment of an amalgamation tailing.3 Mullhollen, in 1911. described the chemical reaction of HgS with Na,S and alkaline hydrate to be:4 Most investigators have reported using a 4-pct sodium sulfide and a 1-pct sodium hydroxide soluti~n.3-4 An increase in temperature or excessive dilution of the solution causes the reaction to be reversed. Church Holmes described a similar process used for the extraction of antimony from silver concentrates at the Sunshine Mining Company&apos;s mill at Kellogg. Idaho.5 More recently. Erspamer and Wells reported the results of leaching studies on a Hg-Sb ore from Alaska.6 EXPERIMENTAL PROCEDURE Leaching tests were made on samples of mercury ore from eight deposits in Oregon, Washington, and Idaho. In addition. tests were made on flotation concentrates from seven of the samples as well as a flotation concentrate from an operating mill. Since previous investigators reported reagent requirements greatly in excess of that required by the equation HgS + Na2S = HgS . Na2S, initial studies were made on chemically pure HgS. Results showed that the reaction actually required about 1 g of Na,S per g of HgS in an aqueous solution rather than 0.338 g of Na,S as indicated by the equation. To check further the matter of reagent requirements, Na2S and HgS were mixed together in equal mole ratios. Water was then added, a drop at a time, until the components reacted; X-ray diffraction analyses showed no HgS nor Na,S present. The yellow hydrate compound which formed would not redissolve until about three additional mole equivalents of Na,S were added to the solution. This indicated that a stable solution would require at least 4 moles of Na2S for each mole of HgS. While these implications may be valid for pure HgS, the possibility of entirely different results caused by the existence of other elements present in ores and concentrates was recognized. Consequently, experiments of the same order were made on samples of a flotation concentrate from a producing mill. The concentrate, containing about 18 pct

Jan 1, 1962

By J. R. Morison, M. P. O’Brein, J. W. Johnson, S. A. Schaaf

The force exerted by unbroken surface waves on a cylindrical object, such as a pile, which extends from the bottom upward above the wave crest, is made up of two components, namely: 1. A drag force proportional to the square of the velocity which may be represented by a drag coefficient having substantially the same value as for steady flow, and 2. A virtual mass force proportional to the horizontal component of the accelerative force exerted on the mass of water displaced by the pile. These relationships follow directly from wave theory and have been confirmed by measurements in the Fluid Mechanics Laboratory of the University of California, Berkeley. The maximum force exerted by breakers or incipient breakers is impulsive in nature, reaching a value much greater than that produced by unbroken waves but enduring for only a short time interval. This impulsive force represents the ultimate development of the accelerative force and is produced by the steep wave front and large horizontal acceleration at the front of a breaker. This impulsive force greatly exceed. the drag force computed from the particle velocities of the breaker. The reader is cautioned that these preliminary results are applicable only to single piles without bracing and are likely to be modified somewhat where multiple piles are driven, one within the influence of the other or where multiple piles are connected by submerged bracing. This paper is essentially a preliminary report submitted at this time because of the current importance of wave forces in the design of offshore structures. An extended series of additional experiments is planned for the near future. Theoretical Relationships For the sake of simplicity of treatment, the theory will be developed from the equations for waves of small amplitude. The horizontal displacement of a water particle is described by the equation 2p cosh — (d + z) H L 2pt X =----------------------sin ----- . , (1) 2 2pD T sinh------ L The horizontal component of the orbital velocity is obtained by differentiation with respect to time as 2p cosh — (d + z) pH L 2pt u = ------------------- cos— .... (2) sinh- L The acceleration of the water particles at any position is obtained by again differentiating with respect to time as 2p cosh — (d + z) 9 u -2vH L 2pt -----=----------------------------sin ----- . . (3) 3 t T2 2pd T sinh------ L where H = wave height — ft L = wave length — ft d = still water depth — ft z = depth below the still water measured negatively downward — ft. T = wave period — sec t = time — sec The force exerted on a differential section, dz, in length is pD2 s u pD 1 dF= [CM (p/4) st + Cn/2 u2] dz • • (4) where D = pile diameter — ft p = water mass density — slugs/ft3 C, = coefficient of mass C,, = coefficient of drag Substituting for a s u/s t arid u2 from Eqs. (3) and (2), the force per unit length at any position z is dF p2 pD H2 &apos; / = — [- fM sin ? ± fD cos2 ? ] . . . (5) dz 2T2 fM D fD 2pt Cm = pA/H:CD = A2;? = T [+ cos2 ? for 0 < ? < p/2 cosh— (d+z) 3p L — < o < 2p Sin L -cos2 ? for p/2 <? <3p/2 The sin 9 term (inertia) i- negative for 0 < 0 < p and positive for p < ? < 2p. Values of A and A&apos; appear in Fig. 1

Jan 1, 1950