Search Documents

By A. I. Krynitzky, Henry S. Rawdon

The most commonly used material for terminals in spark plugs is commercial nickel wire, because of its relatively high temperature of melting, excellent heat conductivity, and slow rate at which the metal is oxidized, even upon continued heating at high temperatures. The grade commonly used for this purpose averages 97 per cent. nickel, the remainder being manganese, cobalt, iron, copper, with traces of other impurities always found in commercial nickel. A peculiar and interesting type of deterioration that occurs in these nickel terminals during the service life of the spark plug was recently brought to the attention of the Bureau of Standards. Commercial spark plugs vary greatly in their size and shape and the terminals differ considerably as to their relative size, shape, number, and arrangement with respect to one another. Although this defect was studied in detail in only one form of spark plug, the deterioration is a characteristic of the material, i.e., of nickel wire, rather than of the particular type of spark plug in which it was noted and studied. The mechanical features of the plugs, however, have a considerable bearing on the time required for the deterioration to become serious. The results of this study of the deterioration of nickel terminals in service should be of value to the makers of all types of spark plugs in which the terminals are made of this metal. CharacteR of Deterioration of WIres During Service Macroscopic Appearance and Properties of Changed Wire.—The nickel terminals in which the deterioration was studied were taken from spark plugs having a central terminal with the ground or side terminals attached firmly at both ends to the shell of the plug. In some of the plugs, two side terminals were used, one on each side of the central one. Although both terminals were found to have deteriorated to some extent, the attack of the central one was quite negligible compared to that of the side ones. These latter wires had developed, in service, transverse cracks that, in many cases, were as sharp and definite as a knife-cut. After a separation occurred, the breach widened by loss of material from the

Jan 1, 1921

By Donald C. Barton

OF the four papers that comprise this Technical Publication, three are case histories of individual geophysical prospects, subsequently tested by drilling. The bibliography of Dr. Barton's published scientific paperst includes investigations in physiography and surface geological mapping, as well as his geophysical papers, and from this list it is to be observed that he early recognized the place of different types of geophysical prospecting methods in the search for geological structures of economic importance. Moreover, his viewpoint was not merely that the structures should be found, but that the geophysical data should be examined quantitatively to determine the geometry of the structures. In other words, that although these data are insufficient to deduce a unique form for the structure that caused the effects measured in the data, the engineering computations should be carried out to give as much of a definite configuration to the structure as the data permitted, in order that the testing of the structures could be conducted in the most economical manner and with the idea that the experience so gained could be later incorporated in the study of structures subsequently found. Dr. Barton continually emphasized the quantitative use of geophysical observations, whereas at the time that he began his specialization in geophysics it was considered sufficient to use observations only qualitatively. He, more than any one else, was responsible for the first volume on geophysical prospecting issued by the Institute in 1929, and his three articles in that volume stressed the quantitative use of geophysical prospecting. The fourth article in this present Technical Publication is a further contribution to this branch of geophysical interpretation, and is a supplement to the paper in the 1929 volume, "Calculations in the Interpretation of Observations with the Eötvös Torsion Balance." From the successful demonstration by Dr. Barton of the usefulness of quan-

Jan 1, 1946

By Donald C. Barton

OF the four papers that comprise this Technical Publication, three are case histories of individual geophysical prospects, subsequently tested by drilling. The bibliography of Dr. Barton's published scientific paperst includes investigations in physiography and surface geological mapping, as well as his geophysical papers, and from this list it is to be observed that he early recognized the place of different types of geophysical prospecting methods in the search for geological structures of economic importance. Moreover, his viewpoint was not merely that the structures should be found, but that the geophysical data should be examined quantitatively to determine the geometry of the structures. In other words, that although these data are insufficient to deduce a unique form for the structure that caused the effects measured in the data, the engineering computations should be carried out to give as much of a definite configuration to the structure as the data permitted, in order that the testing of the structures could be conducted in the most economical manner and with the idea that the experience so gained could be later incorporated in the study of structures subsequently found. Dr. Barton continually emphasized the quantitative use of geophysical observations, whereas at the time that he began his specialization in geophysics it was considered sufficient to use observations only qualitatively. He, more than any one else, was responsible for the first volume on geophysical prospecting issued by the Institute in 1929, and his three articles in that volume stressed the quantitative use of geophysical prospecting. The fourth article in this present Technical Publication is a further contribution to this branch of geophysical interpretation, and is a supplement to the paper in the 1929 volume, "Calculations in the Interpretation of Observations with the Eötvös Torsion Balance." From the successful demonstration by Dr. Barton of the usefulness of quan-

Jan 1, 1946

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By Arthur Taggart

THIS paper describes the result of a series of experiments run in the laboratory of the School of Mines, Columbia University, during the winter of 1927-28. It shows that the several operating adjustments of a pneumatic table produce effects in the action of a, given coal that may be grouped into two classes, viz.: stroke length, speed and rocker-arm angle, which affect longitudinal travel; air supply and table slope (transverse and longitudinal), which determine transverse travel. The magnitude of the effect of the different adjustments varies. Some of the adjustments affect stratification of the bed, both as respects size and specific gravity of the bed components, as well as direction of travel. Operation of a pneumatic table is fundamentally different from that of a wet table in that the former exerts, through the air supplied, a force on the particles upward away from the deck which is lacking on the wet table while, on the other hand, it lacks the positive control over cross travel that is supplied by the wash and feed water.

Jan 1, 1929

By Frank Linforth

THE object of this paper is to present a brief outline of the methods of geologic mapping employed in the Geological Department of the Anaconda Copper Mining Co., at Butte, and to show by means of a few typical examples the practical nature of the results obtained. The extremely complicated geological conditions early encountered in Butte mining led mine operators to realize the necessity of accurate detailed geologic mapping as an aid to successful development of the ore bodies. The organization of the Anaconda Geological Department was undertaken in 1900 by H. V. Winchell, who, in conjunction with D. W. Brunton, worked out the essential methods of procedure which are, in the main, followed at the present time. Since the year 1906 the geologic work has been under the direction of Reno H. Sales, and in some respects the scope of the work has been slightly enlarged. Au excellent article describing the general equipment of the geological department was presented by D. W. Brunton at the British Columbia meeting of the Institute in 1905.1 His idea, that data collected underground and recorded should be put to practical use and not remain a mere " inventory of the company's underground possessions," is the keynote to the success of applied geology in Butte. The geologic notes are taken as soon as possible after the ground is broken so that any mistake in the mining may be corrected at once, or any particularly advantageous procedure may be suggested before any useless work is done. Taking the notes underground is a comparatively simple matter, but a few necessary precautions may be pointed out. The essential to success is that the notes shall show exactly what geological facts are disclosed. The observer must discriminate carefully between important and unimportant exposures in making the record, especially as regards the relation between veins and stringers, between faults and minor slips, or between the characteristics of veins of different ages. A simple color scheme has been adopted for making this record: Red pencils are used to indicate.

Jan 11, 1913

By E. A. von Hahn, T. R. lngraham

The rates of cementation of pd11 on electropolislzed copper cylinders were studied in aqueous perchloric acid solutions at pdII concentrations from 0.02 to 0.1 mM. The cylinders were rotated at various high speeds to reduce the diffusion layer to a minimum thickness. In 0.1 M HClO4 solutions, the cemented palladium is dense, adherent, and shiny. The rate data indicate that there are two stages in the deposition. In the initial stage, the rate of cementation is first order with respect to the pd11 concentration. The second stage is much slower. The first stage is consistent with rate control by the diffusion of pd11 ions to the copper surface, and/or chemical reaction at the surface, and the second stage is consistent with rate control by the diffusion of copper ions from the cop-per surface through the deposit of cemented palladium, out to the main body of solution. In 0.001 M HClO4 solution, only the first stage is evident and the rate is more rapid than at higher acidities. This rate enhancement is attributed to PdOH+ ions that predominate at low acidity and aye more reactive than unhydrolyzed pdII. The deposit is porous and loose. All of the cemented deposits are Pd-Cu alloys rather than pure palladium. Activation energies are 9.5 kcal per mole in 0.1 M HClO4 and 7.4 kcal per mole in 0.001 M HClO4. CEMENTATION or displacement reactions occur between aqueous solutions of metal salts and immersed metals according to the general equation: where M1 is electrochemically the more noble metal. Although these reactions find considerable application in metals recovery processes (e.g., the cementation of copper192 or gold3), in electrorefining processes (e.g., solution purification before electrolysis4,5), and in plating and metal finishing processes,6 few studies have been made of the kinetics of such reactions.7-9 The rates of cementation reactions will depend on one or more of the following factors: a) chemical reactions at the metal-solution interface; b) ionic transport to or away from the interface;'-' and c) the character and adherence of the cemented deposit on the substrate metal,6a,10 because the deposit will inhibit the rate of transport of dissolving ions (M2m+) into the solution. In this investigation, the kinetics of the early stages of cementation were studied to obtain an understanding of the reaction mechanism under conditions in which the deposit was sufficiently thin that its inhibiting effect could be disregarded. To achieve this, very dilute solutions in Mn+ were used. Cementation rates are often fast in the initial stages and transport-contr01led.9 To find conditions under which transport control would shift to chemical control, very high stirring velocities were used to minimize the diffusion-layer thickness. Of the many possible cementation reaction systems, the palladous perchlorate-copper system was chosen for this investigation because it was believed to involve simple ion-for-ion exchange. In addition, there are no interfering side reactions, such as the reduction of hydrogen ions, and anion effects are usually absent in perchlorate solutions. EXPERIMENTAL Materials. Reagent-grade chemicals and redistilled water were used in all experiments. Palladous perchlorate stock solutions (0.02 M) were prepared by dissolving 99.5 pct Pd sponge (Johnson Matthey and Mallory Ltd.) in concentrated nitric acid, adding concentrated perchloric acid, evaporating twice slowly (to prevent PdO precipitation) to a small volume, and diluting in a volumetric flask. To prevent gradual hydrolysis of PdII, the stock solutions were made 0.4 M in HC104. Tests for pdIV (Ref. 11) and C1- were negative. Copper strips were cut accurately from 0.025-in. electrolytic tough pitch sheet, Sample 1 (Mines Branch stock or Canadian Copper Refineries Ltd., Montreal), or from oxygen-free, high-conductivity sheet, Sample 2 (American Metal Climax O.F.H.C. brand, sold by Utility Brass and Copper Corp., Brooklyn). The strips were annealed for 1 hr at 335°C in a stream of purified nitrogen (Union Carbide, Linde Division) which had

Jan 1, 1967

By J. J. Egan, A. B. Kinzel, W. Crafts

Advances in the production of quality steel have emphasized the need for greater knowledge of the amount and distribution of oxygen in the steel. Control of inclusion content and quality is largely dependent on such knowledge. While many analytical methods have been devised for the accomplishment of this end, few are without serious limitations in accuracy, convenience, or skill required in application. Usually at least two methods are necessary to determine total oxygen and constituent oxides. Because of the great importance of this problem and the specific interest in the application of such methods of analysis, the various procedures were carefully reviewed at the Union Carbide and Carbon Research Laboratories, with the view of developing a method free from the limitations mentioned above. Intensive experimentation finally led to an improved iodine extraction analysis described by Cunningham and Price.1 After this had been thoroughly checked from the standpoint of the analytical chemist, it was rechecked from that of the metallurgist. This involved preparation of a number of small heats of varying composition with determination of total oxygen in the molten metal by the alumina method2 and an analysis of the solidified material without the aluminum addition by means of iodine extraction; the oxides of iron, manganese, silicon and aluminum also being determined by the iodine analysis. The report of this work constitutes the subject of this paper. The Iodine Method Fundamentally the iodine method is well established. It is based on the procedure first described by Eggertz3 and depends upon the fact that iron, manganese, silicon and aluminum, as well as the metallic constituents of the pertinent sulfides, carbides and nitrides of these metals

Jan 1, 1933

By O. W. Ellis

RECENTLY there has been a considerable revival of interest in the effects of the various elements commonly added to brass for the purpose of increasing its strength. For many years the work of Guillet2? alone gave reliable information in this regard. Even today his determination's of the coefficients of equivalence of the various elements relative to zinc in brass are those universally employed in industry. This is so because these coefficients have stood the test of time-their substantial correctness has been proved in almost universal practice. It is not our intention to discuss here these coefficients or their use. Rather do we wish to emphasize the need for further systematic studies of the mechanical properties of the ternary systems of copper, zinc, and other individual elements. Since Guillet published the results of his first investigations Millington,16 Smalley33 and Thibaud45 have added somewhat to our information. In general they have confirmed the findings of Guillet, which may be stated in the following rather general terms: 1. The addition of aluminum to the 70:30 and 60:40 brasses progressively increases their hardness and strength and reduces their ductility and resistance to shock. 2. The addition of small amounts of iron to a 60:40 brass improves its strength without affecting its ductility. 3. The addition of small amounts of manganese to a 60:40 brass causes a progressive increase in its strength and reduction in its ductility. A considerable amount of information has been amassed in regard to the effect of nickel on brass (9, 22, 41) which it is unnecessary to refer to here, in view of the scope of this paper.

Jan 1, 1929

By A. E. Bellis

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operations. Hundreds of dollars' are spent in the design and manufacture-of milling cutters of special form ,for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring the tool out "clean," is a difficult: one and calls for no small amount of skill. In order to be on the safe side, the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be-protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed steel, in which metallographic means were used to determine the correct hardening temperatures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accompanying table. Six specimens from the same bar :of each: kind of steel

Jan 1, 1917

By Wei-Kao Lu, G. Bitsianes

An improved general rate equation for a one-ditnensional gas-solid system has been derived. Fov the veversihle interfacial chemical reaction, there are concentrations of gaseous reactant and product at the reacting zone to be considered. They have been calculated with the velations fuvnished by the constraints on the system, namely, quasi-steady state and equimolal counterdiffusion of the gases. The results of the diffusiori study of Evans, Watson, and ,Mason based on the "dusty gas" model have been applied here. The interfacial chemical reaction is taken as first-order with respect to the concentration of the gases involved. The equation has proper dependence on gas composition and on solid structure through the relative values of Knudsen and normal diffusivities. The existence of the total pressure gradient inside the specimen has been predicted and confirmed experimentally. In a previous communication' we introduced a general rate equation for gas-solid reactions by considering the contributions of chemical reaction at inter- phase boundaries and diffusion through the solid product layer simultaneously. These equations, for one-dimensional and spherical specimens, take care of the whole range continuously from purely diffusion control to purely chemical reaction control. In this paper we study only the one-dimensional system. The corresponding rate equation is reproduced here: Of the two terms on the right-hand side of Eq. [I], the first represents the contribution of interfacial chemical reaction and the second that of gaseous diffusion. The shortcomings of Eq. [I] are that in its derivation the interfacial chemical reaction was assumed to be irreversible and the diffusion rate of gaseous product was not considered. Any pressure effects building up within the porous media were also neglected. Evidently. these simplifying assumptions will limit the general applicability of these equations. The rate of reduction of iron oxide by hydrogen, for instance, is very sensitive to the concentration of water vapor in the main gas stream, as has been reported by cewan' and by Quets et a1.3 Furthermore, the gaseous phase at the reacting interface will contain an appreciable amount of the gaseous product of reaction. If this were not true, a sufficiently high concentration gradient for the outward diffusion of the gaseous product could not be maintained. With these shortcomings in mind, Eq. [1I cannot be rigorously ap-

Jan 1, 1967

By T. L. Berger, M. C. lnman, M. F. Rose

AFTER shock loading, mechanical twinning has been observed by several authors1-4 for a variety of fcc metals and alloys. It has been shown2,3 that low stacking fault energy materials deform primarily by the formation of mechanical twins and stacking faults during dynamic loading. Further, Inman, Murr, and Rose2 have shown that a correlation exists between the average hardness and the volume percent of mechanically twinned material in stainless steel. It has been observed in nickel' that mechanical twins are produced during shock deformation if the peak pressure associated with the shock wave is greater than 350kbar. It is the purpose of this work to discuss shock-hardening mechanisms in nickel and to determine to what extent the initial condition influences the final response. The "flying plate technique" was used to generate planar shock waves with peak pressures as high as 710 kbar. The details of the technique5" have been discussed elsewhere and will not be repeated here. The material used in this study was polycrystalline nickel of 99.98 pct purity and had an initial grain size of 0.18 mm. Prior to any deformation, all samples were given a stress-relief anneal of 6 hr at 600°C in a vacuum furnace. After annealing, the initial condition of the samples was changed by cold rolling individual samples from 0 pct to a maximum of 80 pct reduction in thickness. This provided samples with controlled initial histories for shock deformation. Immediately after shock loading, the specimens were slowed and quenched by suitable arrangement of buffer material and water bath. This technique minimized specimen damage and the effects of shock heating on the samples. Since deformation twins in high stacking fault energy fcc metals are only produced at high stress levels, the initial defect configuration prior to mechanical twinning should greatly influence the number of twins formed. In fact, Zukas and Fowler7 have found that prestraining in iron and steel greatly suppresses the formation of mechanical twins during the shock deformation process. Following the methods of Warren and warekois8 and Cohen and Wagner,9 X-ray diffraction profile analysis was performed to determine the incidence of stacking faults and mechanical twins in the deformed nickel. Analysis was made on samples in the annealed, cold-rolled, shock-loaded, and cold-rolled—shock-loaded states. The estimated accuracy of the peak position measurements is *0.01 deg in 2?. Therefore the accuracy in the measurement of the relative peak shifts between the (400) and (222) diffraction line profiles is on the order of *0.04 deg in 2?. None of our measurements indicated peak shifts greater than 0.04 in 28. This would correspond to a fault density of -1 pct and sets the limit on the sensitivity of our instrument. Similarly, analysis of the shift in the center of gravity of the diffraction line profiles yields the minimum measurable value of the twin fault probabilitya to be -0.002. Fig. 1 shows mechanical twinning in nickel shock-loaded to 400 kbar. In this photograph, fault intersections are clearly visible. The thickness of the individual fault lamellae was determined from the image widths of their lines of intersections by the

Jan 1, 1968

By J. W. Mitchell

Season cracking of 70-30 cartridge brass cases of small arms and artillery ammunition has been under investigation at the Frankford Arsenal for many years. The nature of this stress-corrosion failure has been found to be intergranular. Much of this work, however, has been directed toward improvements in method of manufacturing the cases so as to reduce the tendency to season crack and little progress had been made toward finding the source of the chemical agent producing the inter- granular corrosion. Ammonia has been shown to produce season cracking in brass and is known to be present in certain atmospheres, particularly industrial, in sufficient concentration to cause cracking. However, in the case of small arms ammunition, the hypothesis that atmospheric ammonia is the cause will not hold, since small arms ammunition is hermetically sealed during storage and yet occasional lots are found to have cracked after 3 to 5 yr. storage. Much of the early study of season cracking in small arms ammunition was done by Nicholas H. Murdza of the Frank- ford Arsenal. In 1936, he suggested that the corrosive agent might be one of the decomposition products of smokeless powder and mentioned nitrogen oxides specifically. Then in 1937, Murdza suggested that the breakdown of smokeless powder in storage resulted in the formation not only of nitrogen oxides but also ammonia

Jan 1, 1945

By Harry M. Bendler, W. A. Wood

Electron metallography has been applied to the study of the torsional fatigue of polycrystalline OFHC* copper. The development of slip bands, fis- sures, and microcracks has been followed as a function of strain amplitude and number of cycles. Those factors that have been found to be relevant to a geometrical theory of the fatigue process are described. From the point of view of this theory it is important to distinguish between the effects of cycling at large amplitudes and at small amplitudes (true fatigue deformation). EARLY investigations showed metal fatigue cracking is caused by continued reversal of a small plastic strain. Fundamental study of fatigue, therefore, has been largely concerned with the cumulative effects of these plastic reversals on the metal structure. In particular, recent work has shown that the plastic reversals produce slip movements that are finer than the slip movements produced by unidirectional increments of plastic strain; individual slip movements in fatigue, for instance, are too fine to see by optical microscopy.2 It has also been shown that the fine slip movements of fatigue tend to concentrate in bands and that in this way they can build up, after enough cycles, a progressive surface disturbance. It is this disturbance which, in effect, makes the slip movement visible. It is also in this disturbance that the first cracks appear to form. From this point of view, therefore, the problem of fatigue becomes one of finding why the fine slip movements should concentrate in bands and why the. bands should finally open into cracks. Thus far, study of the slip bands has been limited to the changes they produce at the surface only. These studies have given interesting results. Ewing and Humfrey3 many years ago showed that the bands in iron could extrude debris. Forsyth found that bands in aluminum alloys could extrude thin tongues of material. Thompson showed that, after lightly dissolving away the surface of copper specimens, some bands persisted as superficial cracks might, and that the life of a specimen under fatigue deformation might be prolonged by dissolving away the surface at intervals. Thus these and related results have suggested that the metal structure in fatigue bands may disintegrate and that this may happen long before obvious cracking. These surface studies, however, have not shown definitely how cracking may begin, for they do not show sufficiently what is happening in depth. However, some advance in this direction has been made recently by a new approach, summarized later, which reveals slip bands and their surface disturbances in section. In the work done thus far, the sections have been studied by optical microscopy only. In the present work they have also been studied by electron microscopy with extended results. This paper also describes some observations on the surface disturbances prior to sectioning. These observations are relevant to a suggested theory of fatigue cracking. REVERSED SLIP MOVEMENTS Slip movements in fatigue deformation must reverse direction in each cycle. The question arises: DO the "backward" and "forward" movements take

Jan 1, 1962

By C. L. Sollenberger, Will Mitchell, Ford F. Miskell

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Robert Mehl

A STUDY of the structures arising from the decomposition of the a solid solutions in the Cu-Zn and the Cu-Al systems is of peculiar interest in the study of the mechanism of precipitation from solid solutions. It is possible in these alloys, by varying the composition within the ß field, to precipitate from the same basic lattice phases having different lattice structures. It has been rather generally assumed heretofore that the type of structure originating from the decomposition of a solid solution-the Widmanstätten structure-is determined by the lattice structure of the parent solid solution alone. In the first paper of this series1 evidence was advanced which threw doubt upon this hypothesis; but definite proof of the correctness or incorrectness of the hypothesis should be forthcoming from a study of these alloys, for if the structures originating, for example, from the precipitation of the a phase from ß and of the -y phase from the ß in the Cu-Zn system should be shown to be crystallographically different, the hypothesis would necessarily be held as definitely disproved. Furthermore, the newer proposal enunciated in the first paper of this series-that the origin of the Widmanstätten structure lies in a cooperation between the lattice of the parent solid solution and that of the precipitate-which at present seems the only alternative hypothesis, would in such an event be given added weight. The work here reported shows that the Widmanstätten structures originating in the precipitation of the a phase from the a and in the precipitation of the -y phase from the ß in the Cu-Zn system are indeed crystallographically different; and incidentally presents some new descriptive information on the Widmanstätten structure from a more general point of view.

Jan 1, 1931

By M. G. Corson

UNTIL recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast state, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes -cakes, bars, ingots and billets-for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This led to four investigations: by E. Seidl and E. Schiebold,1 by P. Siebe,2 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a' wide zone of columnar crystals between the thin layer of fine crystals near the surfaces of the bars and the large but more nearly: equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the casting machine. More recently, cast shapes of copper were investigated by N. P. Allen5 and by C. Blazey.6 Allen examined vertically cast wirebars and horizontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composition and average densities of the tough-pitch horizontally cast wirebars used. As far as the present writer can tell, no investigation was undertaken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, tough-pitch or otherwise.

Jan 1, 1938

By Arnulf Muan, Klaus Schwerdtfeger

Equilibrium ratios C02/C0 of a gas phase coexisting with selected phase assemblages of the system Fe-Mn-0 have been determined in the temperature range 1000" to 1300°C. The oxygen pressure for the "hfnO" +hfn30, equilibrium and for the "(Fe,hTn)O" + (Fe,Mnh 0* equilibrium at high manganese contents has been determined by electromotive force measurements using stabilized zirconia as a solid electrolyte. The notstoichometry 01' "hTnO" and of "(Fe, iM1z)O" solid solutions has been determined by ther-mog-/avi?netry and by wet-chemical analysis. The data obtained are used to derive activity-composition relations in "(Fe,hfn)O" and (Fe,Mn),O4 solid solutions. WUSTITE "FeO" and manganosite "MnO" form a continuous series of solid solution at high temperatures,' and so do magnetite Fe304 and the high-temperature, cubic modification of Mn304 (Ref. 2) (high hausmannite, -1170). The oxides "FeO" and "MnO" are cation-deficient phases.495 The nonstoi-chiometry of "(Fe,Mn)O" solid solutions has been studied by Engell and ~ohl' at two selected C02/C0 ratios at 1250°C. The two oxide end members of the spinel solid solution, FesO4 and Mn,04, however, are known to be close to stoichiometric under the experimental conditions used in the present investigation.''' The oxygen pressures of "(Fe,Mn)07' solid solutions in equilibrium with iron have been determined by Schenck and coworkers,8 by Foster and welch," and by ~n~e1l.l' The two former groups equilibrated the condensed phases in C02-CO atmospheres of lmown compositions, whereas Engell" used a galvanic cell with stabilized zirconia as a solid electrolyte. The results of these investigators are not in good agreement. Activities of FeO in manganowiistite as calculated from the results of Foster and Welch show ideal behavior, those of Engell yield a pronounced positive deviation, and those of Schenck et 01. show a moderate positive deviation from ideality. In the present work oxygen pressures for the iron + manganowiistite and manganowustite + spinel equilibria and the nonstoichiometry of manganowiistites have been measured. The data were used to calculate activities in the manganowiistite and spinel solid solutions. EXPERIMENTAL METHODS The COz/CO ratios at which manganowustite and iron are in equilibrium were determined by thermo-gravimetric and quenching methods. Experimental details are described in a previous publication.'2 In the thermogravimetric technique, incipient reduction of manganowiistite pellets to metallic iron was observed as a break in the weight vs log COZ/CO curve. In the quenching technique, manganowiistite samples were partially reduced to metallic iron, or the metallic iron of manganowustite + metallic iron mixtures was partially oxidized to manganowustite, in atmospheres of constant C02/CO ratios. After quenching the composition of the oxide phase was determined by X-ray lattice parameter measurements and comparison with a standard curve obtained from oxide solid solutions of known compositions. The nonstoichiometry of "MnO" and "(Fe,Mn)07' solid solutions was determined by chemical analysis of samples equilibrated in C02-CO atmospheres and quenched to room temperature, as well as thermo-gravimetrically by reducing (Fe,Mn),04 or Mn304 to manganowiistite or manganosite. The equilibrium between manganowiistite and (Fe,Mn),04 was measured thermogravimetrically by reducing (Fe,Mn),04 solid solutions having composition in the range of %„ l(NFe +NM) from 0 to 0.63. No experiments could be performed with this technique at higher manganese contents, because the equilibrium C02/C0 ratios are too large for accurate control. An additional difficulty arises at the higher manganese contents due to the strong increase in oxygen content of the manganowustite phase with increasing log Py near the manganowiistite-spinel boundary. Consequently a sharp break in the weight loss vs log C02/CO curve cannot be observed at the phase boundary. At high manganese contents of the manganowiistite, e.g., (NMn/(NF~ + NMn) > 0.9, electromotive force measurements with stabilized zirconia as a solid electrolyte were made to determine the equilibrium oxygen partial pressure. Experimental details are described in a previous paper.* Mixtures of "(Fe,Mn)O" and (Fe,Mn),04 were pressed to pellets, and the oxygen pressure of the equilibrated samples was compared to that of Ni + NiO mixtures in the cell The composition of the manganowiistite in the equilibrated two-phase mixture was determined by lattice parameter measurements and comparison with known standards. The oxygen pressure for the Ni + NiO equilibrium was taken from available data.l3~l4 No reliable results were obtained with the electromotive force technique on iron-rich oxides. The electromotive force drifted strongly with time in this composition range. An additional difficulty arises from the partial de-

Jan 1, 1968

By S. C. Herold

Considerable interest has been shown, during recent years, in the possibilities of developing oil fields in the South American Republics, now that the exhaustion of our present fields can be seen in the not very distant future. The demand for fuel 011 and its products has been increasing far more rapidly than our increment of production during the last few years. Increase of consumption has been largely curtailed by the lack of sufficient supply. The main factors that have contributed to our previous neglect of the southern fields have been as follows: (a) Lack of sufficient demand for the product. (b) Competition with producing fields, having large production, low cost, and better geographical position, such as Tampico, Mexico. (c) Greater interest in home fields with ready market at hand. (d) Our ignorance of southern economic and geologic conditions, due to the distance between those areas and our financial centers. (e) Economic conditions in the southern countries, necessitating high costs of exploration and exploitation of the fields. (f) Our lack of understanding of the business methods of the Latin-American. It must be borne in mind that the oil-development work done to the present time in South America has, with one exception,' been undertaken upon lands which possessed direct evidence of oil in seepages or asphaltic deposits, occurring either immediately upon the lands or in their close vicinity. The development of oil fields in South America is therefore in the pioneer stage. It is not at all improbable that "hidden fields" will be uncovered in future work, as has occurred notably in the mid-continental field of this country within recent years. Location The areas grouped as a unit under the title of North Argentine-Bolivian oil field extend in a narrow belt from the north-central part of

Jan 1, 1920