Search Documents

By Gerald C. Dohm

INTRODUCTION After a mining company has discovered a mineral deposit, the problem is then how to mine and process that deposit the best way. The principal problem facing managers or engineers who must decide on mine plant size, equipment selection, and long-range scheduling is how one can optimize a property not only in terms of efficiency but also as to project duration. Mine opti¬mization is dependent upon the interaction of con¬tributing parameters which leads to maximizing the net present value (NPV) Realistic mine planning is the key, to the analysis. The process is to be used when evaluating undeveloped properties or when a complete revamping of existing facilities is scheduled The proc¬ess is not intended for detailed mine design but rather for property evaluation and feasibility studies. The derivation of the various input parameters will only be discussed to the point where a meaningful correlation can be made with the overall analysis. The interrelationship of the parameters will be the central point because most company guidelines and financial analysts have their own standards when deriving the various inputs. Assume that the data is totally acceptable and pro¬vides at least the following categories of information and guidelines- (1) mineral and waste inventory; (2) geologic, hydrologic, and geotechnical criteria; (3) topographic layout including property boundaries; (4) metallurgical flowsheet, recovery and design criteria; (5) access, water, power, and environmental base-line study; and (6) financial constraints (minimum rate of return, payback period, etc).

Jan 1, 1979

By J. E. Johnson

Discussion of the paper of Prof. Henry M. Howe, presented in abstract by Bradley Stoughton at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912, pp. 1181 to 1227. J. E. JOHNSON, JR., Ashland, Wis. :-This material is largely beyond the understanding of most of us practical men, but there are certain portions of that diagram that are of enormous importance. We have been conducting a, very extensive investigation of the quality of charcoal-iron and of all iron, and we have found that this eutectic point here (indicating on chart) is a sort of balance point between the good irons and the bad ones, and I have some slides to show what practical results we have found depending on this point here on the d diagram; and it would be a mistake for men who were -concerned with operation and were getting practical results, to think that these things are of no importance. They are exceedingly hard to understand, and I confess that a great deal of them is beyond me, but there is no doubt that the quality of iron depends to an enormous extent on the location of the carbon content of the iron to the right and left of this point, and the position of that point is dependent upon the silicon, and I wish to make a plea to the practical and operating members of the Institute not to disregard this material on account of its being highly scientific, because I hope to show later that there are matters of the highest practical importance that depend directly upon certain portions of this diagram. HENRY D. HIBBARD, Plainfield, N. J. :-T understand that washed metal, which, is practically pure iron and carbon, does not solidify at one instant, is cast-iron does, but passes through a mushy stage. That has been an enigma as to how and why it did so, and possibly some light might be thrown on it in this connection. BRADLEY STOUGHTON, New York, N. Y.:-If Wittorff's propositions are accepted, washed metal containing more than 4.1 per cent. of carbon would begin to solidify as liquid plus Fe4C

Dec 1, 1912

By John Freeman

THE tensile properties of steels at elevated temperatures have been studied by numerous investigators,1 primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20° to 500° C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon of increased tensile strength and decreased ductility in the so-called "blue-heat" range, approximately 200° to 300° C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

By Westwater, J. S.

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W. within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleveland-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. A1len. Mather "A" shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather " B, " also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation.

Jan 1, 1949

By Edward C. Jeffrey

The use of coke in metallurgy, to any important degree, dates from the middle of the 18th century. Its utilization came most opportunely for European civilization. The forests of Europe, except in the most remote and inaccessible regions, had been largely fed, in the form of charcoal, into the smelting furnaces. For a hundred years—the middle of the 17th to the middle of the 18th century—there .was a stationary condition of population corresponding to the exhaustion of European forests. This situation, which was particularly evident in Great Britain, was due to the fact that the forests had been depleted and the practical utilization of coke had not begun. The coking industry is essential for our metallurgical industries, which in turn are basal to healthy economic progress. But coke is of great importance, not only on its own account, but for its byproducts, which enter fundamentally into all the arts of peace and war. The dyestuff industry and the manufacture of explosives are intimately connected with one another, as was shown by the recent war. The subject of coking coal, therefore, is well worthy the serious attention both of practical industry and the scientific investigator. The most valuable coking coals, from the metallurgical standpoint, are derived from the coals of highest ranks. Coals, for example, that have a carbon ratio of from 70 to 80 per cent. yield the most valuable coke for the blast furnace. The difficulty of investigating these coals, however, is great, for they are rather friable and delicate and possess a high carbon content, which makes them difficult to manipulate. They present, on account of their high carbon content, a considerable degree of opacity when examined, in thin sections, under the microscope. The tenderness of structure and blackness of such high-grade coking coals as those of Connellsville and the Pocahontas region make them extremely difficult to investigate. Two of my colleagues, who are taking part in this discussion, will describe the valuable results that have been reached by studying coal by the methods of the mineralogist. Doctor White and Doctor Thiessen have studied the structure of coal as determined from thin sections that

Jan 1, 1925

By Robert M. Grogan, James C. Bradbury

The Illinois-Kentucky mining district has, since 1880, accounted for 80 per cent of all U.S. production of fluorspar. The ore deposits are of two types: vein deposits formed by fissure fillings along faults and bedding-replacement deposits formed by the replacement of strata at certain favored stratigraphic positions along minor faults and fractures. Fluorite is the chief valuable mineral in the deposits. Sphalerite and galena commonly are present in small amounts but, in some ore bodies, may form a substantial part of the valuable constituents of the ore. Calcite is the chief gangue mineral; quartz and barite Exposed strata range from Devonian are present in various amounts. through Pennsylvanian in age. Igneous intrusive rocks occur as mafic dikes and sills and intrusive breccia dikes and plugs. Structurally, the district is situated on a generally northwest- trending arch that has been sliced into a series of long, narrow blocks by normal faults that trend northeastward. The structural The localization of the ore deposits by faults and fractures, the association of fluorite mineralization with intrusive breccias, and various lines of petrographic and geochemical evidence indicate that the fluorite-zinc-lead deposits were epigenetic and deposited by solutions emanating from a deep alkalic magma.

Jan 1, 1968

By F. R. Morral, E. P. Miller

Hot-dipped heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature 01 the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schuelerl by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva. nized wire, which was assumed to be the FeZn10 phase. Since the extensive review of the iron-zinc alloys presented a few years ago,3 much new work has been published, some of which5-l6 was too late to be included in the recent edition (1939) of the American Society for Metals' Handbook.4 Figs. 1 and 2 are reproductions of the latest iron-zinc diagram proposed by Schramml1 as a result of his investigations by microscopic, thermal, magnetic susceptibility and X-ray methods. Table 1 summarizes all the known published X-ray data of the phases Present. The solubility of iron in zinc has been determined by x-ray methods.10 In the same manner the homogeneity range of the P phase was studiedlo using the principle that the parameter of an intermetallic compound changes while the concentration of One of the constituents changes. Schramm10 has found some 80 alpha lines in X-ray powder photograms of phase d1, and from these he believes that this phase is related to the P phase. Previous investi-

Jan 1, 1941

By E. P. Miller, F. R. Morral

Hot-dipped heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature 01 the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schuelerl by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva. nized wire, which was assumed to be the FeZn10 phase. Since the extensive review of the iron-zinc alloys presented a few years ago,3 much new work has been published, some of which5-l6 was too late to be included in the recent edition (1939) of the American Society for Metals' Handbook.4 Figs. 1 and 2 are reproductions of the latest iron-zinc diagram proposed by Schramml1 as a result of his investigations by microscopic, thermal, magnetic susceptibility and X-ray methods. Table 1 summarizes all the known published X-ray data of the phases Present. The solubility of iron in zinc has been determined by x-ray methods.10 In the same manner the homogeneity range of the P phase was studiedlo using the principle that the parameter of an intermetallic compound changes while the concentration of One of the constituents changes. Schramm10 has found some 80 alpha lines in X-ray powder photograms of phase d1, and from these he believes that this phase is related to the P phase. Previous investi-

Jan 1, 1941

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue' back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.' Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962

By Harry T. Hamilton

THE genial assistant to the president of the New York Trust Co. is the latest addition to the Institute's board of directors, having been elected at the March meeting of the hoard to fill the unexpired term of the late E. E. Ellis. Usually when a banker is appointed to the board of a company the reason is obvious; the difference in this case is that the New York Trust Co. has some of the Institute's money, instead of vice versa. But Harry Hamilton is not really a banker-at least not primarily. Frefluently big financial institutions have a good mining engineer on their staffs to keep them from financing too many "cats and dogs." At any rate Mr. Hamilton gave up his consulting practice in San Francisco back in 1927, to accept his present position in New York. Until then, from the time he graduated from Yale in 1904, lie was constantly engaged in mining operations of one kind or another in the West and in Mexico. His first job was at Christmas, Ariz., where lie did "sampling and miscellaneous work" for the Saddle Mountain Mining Co. The writer tramped up to, all over, and through that property one hog day many years later, when it was run by the Christmas Mining Co., and carp assure the reader that without doubt the young Yale graduate got some good experience and was well broken in. From there Mr. Hamilton went to Cananea for a time, and then to the Copper Queen, at Bisbee, where he was a valued member of the rigging gang. An assignment of assaying and sampling for the Shan¬non Copper Co. at Metcalf lasted for a few months and then he accepted a job for a year with the geological department

Jan 1, 1936

Jan 1, 1947

Jan 1, 1947

By C. A. Zapffe, C.E. Sims

Many hundreds of publications have appeared during the past 78 years that treat the subject of hydrogen in iron and steel.l05 but conclusions regarding the functions of hydrogen in causing some important defects in steel are still unsatisfactory to many; and other hydrogen-caused phenomena yet remain to be identified with this gas. The most widely discussed of these defects is hydrogen embrittlement, but the conception, perhaps the popular one, that embrittlelnent is due to hydride formation aoes not conform to the known facts.l04 The true identity of hydrogen embrittlement seems instead to lie in a mosaic nature of metal crystals, which is a concept not Yet accepted by most metallurgists. A study of hydrogen embrittlement therefore provides new viewpoints in regard to the crystalline substructure of steel.

Jan 1, 1941

By C. E. Sims, C. A. Zapffe

Many hundreds of publications have appeared during the past 78 years that treat the subject of hydrogen in iron and steel.l05 but conclusions regarding the functions of hydrogen in causing some important defects in steel are still unsatisfactory to many; and other hydrogen-caused phenomena yet remain to be identified with this gas. The most widely discussed of these defects is hydrogen embrittlement, but the conception, perhaps the popular one, that embrittlelnent is due to hydride formation aoes not conform to the known facts.l04 The true identity of hydrogen embrittlement seems instead to lie in a mosaic nature of metal crystals, which is a concept not Yet accepted by most metallurgists. A study of hydrogen embrittlement therefore provides new viewpoints in regard to the crystalline substructure of steel.

Jan 1, 1941

By J. W. Schroeder

SEAMLESS pipe, the product produced from piercing a solid round billet of steel by the Mannesmann process, was first produced in the latter half of the 19th century, the Mannesmann machine having been patented in 1885. The products of other processes also have been termed seamless pipe; for example, the cylindrical section produced by "cupping," which consists of forming a cup from a flat plate or disk and further elongating the cup into a tube by passing it through a set of reducing dies. The purpose of this paper is to discuss some of the more important metallurgical factors and their relationship to the economical production of seamless pipe produced by the Mannesmann piercing process. The first seamless tube plant in America was established at Shelby, Ohio, in 1891, and was employed in the manufacture of bicycle tubing. For a number of years the bicycle industry was the only user of seamless tubing, and this tubing was produced by hot-rolling pierced billets imported from Europe and finishing on the cold drawbench. At the turn of the century, the automotive industry was responsible for an increase in the demand for seamless tubing. The growth of this industry was the dominant factor leading to the phenomenal growth of the petroleum industry, which in turn created a tremendous demand for seamless pipe. In addition; the old lapweld iron boiler tubes for stationary and locomotive boilers were replaced gradually by seamless tubes. Since 1929, the production of seamless steel pipe and tubes has increased over loo pct. In 1929, 1,459,9031 net tons of seamless pipe was produced, including both hot-finished and cold-drawn material, as compared with 3,087,3122 net [ ] tons in 1948. Table I gives the distribution of seamless pipe by classes for 1948. METALLURGICAL PROBLEMS From a metallurgical standpoint, the production of seamless pipe has presented many problems. Practically every type of steel, carbon and alloy, with the exception of the superalloys developed during World War II, has been pierced and rolled successfully into tubing. This includes bessemer, open hearth, by the stationary and duplex processes, and electric steels. The range of sizes produced is no less staggering to the imagination, when it is considered that the hypodermic needle, which is 0.016 in. diam with a wall thickness of 0.004 in., and pipe for gas or oil transmission lines, with a 26 in. OD, are both seamless tubes. Between these extremes, the range of diameters and wall thicknesses meets most present-day demands for seam-

Jan 1, 1951

By FOSTER HEWElT

THE scope of this paper is the description of two districts in Peru in which deposits of vanadium have been found, and the consideration of much laboratory-work that I and others have done to determine the nature of these deposits. It is with regret that I present some of the data in a state of evident incompletion, particularly the analyses of a few of the minerals, which leaves some doubt as to whether the true nature of the minerals is understood. I make no apology, however, since in this case, as in many others referring to ore-deposits, conclusive opinions cannot be stated until a great amount of work has been done, and the deposit has been thoroughly exploited. I believe that the data and the tentative conclusions here presented indicate a unique and interesting condition which may assist others in work along similar lines; and further, what is of more practical importance, stimulate a search for a metal which, though long considered rare, is probably so merely because proper care has not been taken to recognize it. An excellent bibliography on the occurrence of vanadium in nature is given by F. W. Clarke in his paper, Data of Geo-chemistry;1 and in the preparation of this paper I have consulted many of the references contained in the Bibliography of the Chemistry of Vanadium, by M. Moissan.2 A brief review of the subject having special reference to the metallurgy of vanadium is contained in the small book by P.. Nicolardot.3 One of these vanadium-deposits has already been briefly

Mar 1, 1909

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William C. McCulloch

INTRODUCTION The particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 25,400,000 tons of bituminous coal were cleaned by air machines during 1965. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 19 16, by the Sutton, Steele and Steele Co, Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., seven other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine. 2. Arms "Concentrator," oscillating table. 3. Hey1 and Patterson oscillating table. 4. "Stump Air-Flow," pulsating air jig. 5. "Super Airflow," pulsating air jig. 6. Ridge air jig. 7. Phillip air jig. While not all coals can be beneficiated by air washing, the air washing of coals that are easy to clean can be readily proved advantageous. Of all the preparation methods, pneumatic cleaning is the most acceptable from the standpoint of delivered Btu cost. This is based on the premise that a percent of moisture is just as detrimental as a percent of ash. The principle of dry concentration has never been determined with scientific accuracy. To the present time the study has been more of an art than a science. It is possible to forecast the results of wet concentration from a study of the washability characteristics of the raw coal but only after applying rule-of-thumb methods of interpretation to the specific gravity and size distribution can it be ascertained that the raw coal is amenable to dry concentration. Air as a separating medium dates back to biblical times as exemplified in the winnowing of chaff from the grain. However, the same application of air to coal serves merely to blow the dust away and size the remaining particles. Pulsating air was the solution to the problem and largely eliminated the necessity for close screen sizing which was required on early separators. Because of the low density of air, a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. Also, the

Jan 1, 1968

By Frederic P. Dewey

(New York Meeting, February, 1912.) By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called; platinum. Sometimes it is so, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes jives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid, 1 I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Apr 1, 1912

By S. R. Gilbert, B. W. Burdett, L. B. Hales

INTRODUCTION Grinding control is currently the most publicized control subject in the minerals industry. Flotation control and crushing control have not as yet received the widespread attention that grinding control has. The primary reasons for this center around the high capital costs of grinding equipment and the fact that grinding mills are extremely energy inefficient. In a typical copper concentrator the energy requirements to produce refined copper are: (1) [Total Energy Distribution (Kw-hr/yr)% Mining4.93 x 10817.3 Mineral Processing9.63 x 10833.8 Smelting and Refining13.9 x 10848.9] One-third of the total energy used for copper production is for mineral processing. A breakdown of this energy into process steps yields the following: [Total Energy Distribution (Kw-hr/yr)% Crushing and Grinding 7.16 x 108 73.8 Flotation 0.76 x 108 7.8 Materials Handling1.78 x 10818.4] It is apparent that comminution operations consume the largest proportion of the energy for processing and as such become major targets for improvements in efficiency. Unfortunately, size reduction operations are extremely inefficient. Efficiency calculations for grinding range from less than 0.1% to about 5% depending on the evaluation criteria. Because of these facts, grinding control has been and will continue to be the focus of major process control efforts. OBJECTIVES AND BENEFITS All benefits achieved as the result of grinding control are derived from modifying physical parameters which improve the efficiency of the grinding mill. These parameters include:

Jan 1, 1982

By Claus Guenter Goetzeil

(New York Meeting, February, 1937) The object of this investigation was to determine whether silver alloys could be used instead of the currently employed insert of high-expansion Average Coefficient per Deg. C. over Range 20° to 200° C. Pure aluminum..................................... 24.6 X 10-6 Cast low-expansion Si-Cu-Ni-A1 piston alloy............ 20.0 X 10-6 High-expansion austenitic Cu-Ni cast iron.............. 19.3 X 10-6 Cast steel (0.25-0.35 C, 0.40-1.0 Mn).................. 12.6 X 10-6 Cast iron (3.15 total C, 2.16 Si)....................... 12.8 X 10-6 Pure silver.......................................... 18.9 X 10-6 austenitic ferronickel alloy, to reduce the wear of ring grooves in light metal pistons. A typical example of a piston containing a ferronickel insert is shown in Fig. 1. The high coefficient of expansion of silver made it worthy of consideration, while the small size of the insert would render its use feasible in Germany as an emergency measure. The coefficients of linear expansion of several metals and ailoys are as shown in the table above. Obviously the melting point of the insert must be high enough to prevent it from melting when the light alloy is cast around it. This imposes a lower limit of about 850" C. for the solidus of the silver alloy. Pure silver melts at about 961" C., so that the tolerable depression in the solidus is rather small. To avoid deformation of the insert during use a Brinell hardness number of at least 60 appears necessary.

Jan 1, 1937