Search Documents

By A. Bortolussi

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables an tool performance (cutting rate and bead wear) has been elucidated.

Jan 1, 1992

By Ke Yang

"Engineering practices have shown that the skip-fault longwall mining is frequently used when faults with offsets larger than 1 Om are present. Since the skip-fault longwall mining not only reduces the recovery rate of coal reserves, but also increases the cost due to developing another setup room on the opposite side of the fault and moves the longwall into it. The coal pillar so created induced residual stress in and thus affects the safe mining of adjacent coal seams. In order to investigate the influence on panel layout and retreat by a l 6.5m offset normal fault, the similar material simulation model was constructed based on the geological and engineering conditions of No.13 coal seam in the western district of Liuzhuang coal mine employing the down-dip longwall mining. The characteristics of deformation, movement and failure of the overlying strata and abutment pressure when the face cut through the hangingwall and footwall of a normal fault were obtained. There were significant differences between the hangingwall and footwall as conformed by the equilibrium structure model. The results showed that superposition of the tectonic stress from a normal fault of large offset and that induced by mining is one of key factors that lead the severe pressure difficult to control during panel retreating from the hangingwall to footwall. Accordingly, the technical solutions for a fully mechanized mining face directly cutting through the fault are presented and optimized, and the applications of the technical solution in Panels 171301and171303 of Liuzhuang mine enabled them to complete the mining safely and efficiently. INTRODUCTIONFaults have been one of the important technical factors in underground coal mining l1-2i. Engineering practice has shown that the methods of mining through the faults depend on the seam thickness, seam dip angle, offset of fault throw, equipment height, rock strength, and advancing direction l3-5l. In the fully-mechanized longwall mining, the face normally proceeds to cut through the fault directly if the offset of the fault less than 5m, and to skip Uump) the fault if the offset is larger than 5m. In the former case, the most important problem is to efficiently control or avoid roof fall accidents (i.e., crushing, falling, pushover, and rock burst). In the latter case, the most important problem is very expensive to drive a new setup room and move the face equipment to it. The skipped coal pillar may poses problems for mining in adjacent seams."

Jan 1, 2016

By Frank Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors using sedimentological descriptors, lead to an understanding of the mechanisms causing roof problems. Types of bedding plane features can be categorized into geometric, internal structures, bedding-plane markings, deformed bedding, solution structures, and accretionary structures. Factors such as encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described.

Jan 1, 2002

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By Hideki Shimada

A low cost methodology that allows the determination of in- situ stress using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the AE and DRA methods to those estimated by conventional ANZI (Australia and New Zealand Inflatable) cell measurements. The studies have been focused on fill stress tensor determination from a single oriented cored rock. In all cases the rock core specimens recollected the in-situ stress reasonably well compared with the standard overcoring method.

Jan 1, 2001

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By Kewal K. Kohli

An investigation was performed to determine the sequence of events which caused the 1987 surface subsidence and related damage to several homes in Walker County, Alabama, USA (see Figure 1). Surface affects compared to mine maps indicated the subsidence to be mine related. However, two coal seams had been worked under this area. The upper seam, the American seam ranged from 250 to 280 feet beneath the surface in the area in question. It was mined-out before 1955 by room-and-pillar method leaving in place narrow-long pillars to support the overburden strata, and abandoned in 1955. The lower seam, the Mary Lee seam, ranged from 650 to 700 feet beneath the surface. The Mary Lee seam had been abandoned in 1966 and subsequently became flooded. The dewatering of the Mary Lee seam workings in 1986 caused the submerged pillars to be exposed to the atmosphere. Due to multiple seam mining and the fact that workings had been inundated then dewatered, a subsurface investigation ensued to determine the sequence and ultimate cause of surface subsidence. Core sample tests with fracture analysis in conjunction with "down-the-hole" TV camera inspections provided necessary information to determine that the subsidence started in the lower seam and progressed through the upper coal seam to the surface. Evidence from the investigation program established that dewatering of the lower seam workings caused the marginally stable support pillars and the roof to collapse. This failure triggered additional subsidence in the upper seam which broadened the area of the influence at the surface.

Jan 1, 1992

By Keith Heasley

An eastern longwall mine was required to mine through a set of three entries located midway down the length of a panel. Of course, the mine desired to design a successful support system for the mine-through area at the least cost. To further complicate the design process, the mine-through entries were located directly under the end of a previously mined, overlying longwall panel and the entries were close enough to be subject to stress interactions from the overlying seam. In order to accurately evaluate the multiple-seam stresses and modify the mine-through support system appropriately, the boundary element program LaModel was used to model the stress and displacements in the two mines. Using the results of the model's stress analysis, the support density was systematically varied throughout the mine- through entries for optimum sup@ efficiency and economics. During the actual mining of the cross panel entries, the longwall experienced few, if any, additional delays, and overall, the support and mine through of the cross-panel en- tries at Harris #1 was very successful, saving the mine confineable time and money.

Jan 1, 2003

By Morgan M. Sears, Mark Van Dyke, Gamal Rashed, John Rusnak, Khaled Mohamed

"In 2016, room-and-pillar mining provided nearly 40% of underground coal production in the United States. Over the past decade, rib falls have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Nine of these 12 fatalities (75%) have occurred in room-and-pillar mines. The objective of this research is to study the geomechanics of bench room-and-pillar mining and the associated response of high pillar ribs at overburden depths greater than 1,000 ft. This paper provides a definition of the bench technique, the pillar response due to loading, observational data for a case history, a calibrated numerical model of the observed rib response, and application of this calibrated model to a second site. INTRODUCTION Bench mining is a an underground mining technique typically applied to room-and-pillar mines where full seam extraction on development presents an unacceptably high risk of injury from high pillar ribs or where the mining equipment is not designed to extract the full seam thickness. To mitigate the increased risk associated with high ribs and slender pillars, a more modest thickness is extracted from the top of the seam on development. This is followed by grading the floor and recovering the bottom of the seam with or without extraction of the pillars during retreat mining. A mine located in Eastern Kentucky extracts two seams at depths ranging from outcrop to 2,000 ft. In some areas of the mine, Seam A and Seam B are close enough together to be mined simultaneously. Seam A (top) is mined on development 7 to 9 ft. high for the entire length of the panel. On retreat, as each pillar is extracted, the continuous miner is ramped down into the floor (Seam B), two pairs of Mobile Roof Support (MRS) units are set, and the pillars are extracted at the full mining height of 14+ ft. During the pillar recovery process, the floor is extracted in each entry, from a ramp initiated outby the retreat line, sequentially just prior to extracting the lifts from the pillars (see Figure 1)."

Jan 1, 2017

By W. Mark Hart

The current Automatic Data Acquisition system developed by some support manufacturers make it possible to monitor and record changes in leg pressure, DA RAM stroke in every shield and shearer position at any moment during mining operation. But how can these massive data (more than 1 MB for every 3 hrs for the current scanning option) be effectively used for improving production and maintenance management as well as providing better roof control at a longwall face? The research currently conducted jointly by WWU and Cyprus Amax Minerals at Emerald Mine and Twentymile Mine attempts to answer this question and make the data, especially leg pressure, more meaningful. A computer software package has been being developed to (1) determine mining cycles, cycle time, face advance rate, production rates, machinery delays, and production delays for each shift; (2) identify defective sensors, check valves, yield valves, by-passing leg and DA RAM cylinders, and other hydraulic and electrical abnormalities; (3) determine the roof weighting period; (4) evaluate the performance of the current shield support design - demand relationships; and (5) predict and overcome ensuing encroaching problems and roof conditions ahead of the face.

Jan 1, 1994

By Richard E. Thill

Two Cross-borehole systems were developed by the Bureau of Mines, one operating at a central frequency of 20 kHz for close-in spacing between boreholes (2-20m) and another operating at a dominant frequency between 1-2 kHz for more distant range (40-300+m) between boreholes. The systems are specially designed for the expected ranges and high resolution required in mining applications. Potential applications of the crosshole systems are presented for a variety of geophysical measurements related to underground mining problems.

Jan 1, 1989

By S. S. Peng

This paper presents a convenient way for the preliminary design of the shield supports. The locus equations which are applicable for all kids of shield supports are derived. These equations facilitate the statics analysis of the shields. An indirect method in determining the coefficient of friction, the external toads and their locations are also developed.

Jan 1, 1982

By Winton J. Gale

The subsidence over a longwall panel at Tahmoor Mine in the Southern Coalfield of NSW, Australia, was found to be approximately twice the size it had been in previous measurements. An investigation into the potential causes was conducted using computer modeling together with hydrological characterization and detailed geotechnical characterization of the strata. The abnormal subsidence was found to be consistent with localized weathering of joint and bedding planes above a depressed water table adjacent to an incised gorge. The study showed that other factors such as variation in stress field, joint zones, variation in rock strength and topographic factors did have sufficient impact to induce the abnormal subsidence. The results have significant implications to subsidence prediction in areas that may be prone to the phenomenon found at Tahmoor. Key indicators of the potential for this form of abnormal subsidence are presented.

Jan 1, 2011

By Erdal Unal

In order to define the support parameters, by use of empirical approaches, it is particularly important to analyze the rock-load height that should be controlled by supports. The controlling mechanism however, depends on the type of support used there- fore, the rock loads should be treated differently. In this paper, an empirical equation is introduced which relates the rock-load height (ht) to a quantitative rock quality index (REIR), and roof span (B) as fallows:

Jan 1, 1986

By Ross W. Seedsman

The logical framework recognises that a coal mine roof can be intrinsically stable or may collapse in one of four ways. Suspension of the immediate roof is one of fundamental ground control strategies available to a coal mine engineer and is recommended for three of the four collapse modes. Correctly implemented suspension offers the greatest improvement in roof stability and greatest reduction in longwall risk. For the control of maingates ahead of retreating longwall faces the ideal suspension support (if required) consists of angled, partially debonded, medium-length tendons installed as far behind the development face as practical. For situations where the roof may be subjected to tensile horizontal stress, immediate support by equally spaced short vertical tendons is required. The step away from fully-grouted tendons improves their survivability during the onset of compressive failure in the roof, minimises the risk of isolated loading, and allows a more robust TARP for roof movement. All suspension systems require a strap, sling or truss between the suspension elements.

Jan 1, 2014

By Stephen Tadolini

Reduction in the time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. While this concept is not without controversy and risk, the rewards can result in substantial reductions in longwall face move/set-up times and provide safer working conditions. Both of these factors can reduce mining costs and enhance profitability in a competitive market. This project was even more complex because the longwall system operates under a weak roof condition. To examine the feasibility of this concept, a 16-ft wide by 170-ft long experimental pre-driven recovery room was designed using analytical, empirical and 3-dimensional finite element modeling techniques. Based on the projected loading conditions, immediate and main roof geological and strength characteristics, a variety of roof bolt types were selected and installed in the recovery room and adjacent chutes. To supplement the intrinsic supports, high-capacity roof-to¬floor cuttable cribs were strategically placed to reduce the potential of a weighting failure before the longwall shields safely entered the room. To evaluate the behavior and final support performance, the recovery room and chutes were instrumented to monitor the physical response during various loading phases. Additionally, the cuttable cribs were instrumented to evaluate the loading and stiffness characteristics during the extraction process. This paper describes the successful design process, support methodology, monitoring results, final observations and recommendations.

Jan 1, 2002

By Matthew J. DeMarco

Research personnel at the U.S. Bureau of Mines have conducted longwall gate stability studies at four western U.S. mines attempting to employ yield pillars for improved ground conditions. Located in the Book Cliffs and Wasatch Plateau coalfields of north-central Utah, these operations are generally characterized by multiple-seam mining, cover depths averaging 450 - 600 m (1,500 - 2,000 fl), occasionally extending beyond 760 m (2,500 ft), abrupt cover depth variation due to the overlying canyon/mesa topography, and massive, rigid sandstone roof units. Such conditions encourage severe gate and panel coal bumping, as well as various types of roof instabilities and occasional floor-heave problems. To alleviate these adverse conditions, several mines have employed yield pillars to-reduce hazard-inducing excessive gateroad stress concentrations. This paper describes the evolution of gateroad designs at four of these operations, the specific mining conditions involved, and the general stability performance attained by using yielding gate systems. Mine experiences are "compared" in terms of basic setting conditions, and the general concepts of yielding system applicability and success potential are summarized.

Jan 1, 1993

By Thomas Barczak

Hydraulic cylinders are used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support system operate at pressures as high as 7,000 psi to provide the necessary support capacities Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performmce characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control This paper examines the basic operating principles of state-of-the- art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (5) hydraulic failure mechanisms and how to detect them

Jan 1, 1998

By C. Tom Blevins

The purpose of this paper is to discuss production and roof control problems associated with directional lateral stresses in an in situ stress field and the approach that Inland Steel Coal Company made in trying to cope with them. Before proceeding, a description of the mine location, product, geology, restraints, and mine history is in order. The mine is located in Hamilton County in Southeastern Illinois. It produces a high volatile metalurgical coal and is slated to produce 2.1 MTY. Product ion is in the Illinois No. 5 seam at a depth of 930 feet, approximately 490 feet below sea level. The scam height averages from 5.5 to 6.0 feet throughout the reserves with height increasing in the eastern reserve area to approximately feet and a 5 Foot average in the West. The scam tends to dip to the North, North East, but is locally very undulating. The Galatia channel washout outlines the eastern boundary of the reserves and there is a split coal area toward the central part of the property than runs south-southeast. The top above the #5 seam is laminated medium gray shale called Dykersburg. Individual shale bedding planes vary locally From ½ to 1" in thickness to a more normal thickness of 1 to 1 ½ with some areas being interlayed by thin carboncous material. The top normally must be considered as materially competent. Even though the mine is still relatively small in area with only 1.3 million tons of total production to (late, we have encountered dense zones of slicker sides and premining, stress cracks (joints). There are also areas of siltstone, that vary from a few inches to several feet thick, and areas of rider coal, clay instrusions, and rolls. We have crossed lineament concentrations that show strong evidence of corelation to localise top problems. These are being monitored closely to see their predictability on our present and future mining conditions. The face cleat runs N 55° E and butt cleat runs S. 25° E. On a regional basis, there are several anticlinal belts that trend in a northerly direction. The one major restraint is that Inland does not own surface subsidence rights. Therefore, a partial extraction mining plan is being followed. The Holland-Gaddy formula for pillar strength design is used to calculate theortical pillar sides. When production began in March of 1979, it was noted that ground control problems occurred as we drove north entries. East-west cross cuts tended to have better working conditions. This phenomia occurred from a couple hundred feet, but seemed to dispate as we got away from the men and material shafts. Once the production shaft was connected and enough entries extended for installation of belts, ground control problems were again experienced in north-south headings. It was also observed that when mining north-south headings with east-west crosscuts, if the crosscut was driven through ahead and supported, the intersection was stable upon entry connection. This held true even where fairly extreme ground control, problems were encountered. The reverse held true. when driving east-west headings with north-south crosscuts. At this time, we started searching in earnest for a working theory to explain this roof phenomia. It also became the first step of what eventually was a four step sequence to derive a workable solu¬tion to the problem. The combination of the many geological changes and the fact that north-south condition was at times intermitent, helped to disguise the stress field. The mine also being in a fairly virgin area with no mines in approximately 25 milt, radius, meant we didn't have a reliable case history to examine. Various theories were researched before it was concluded that our primary ground control problem was a directional lateral stress Field, with the major stress axis in an east-west direction. The second stop of the procedure was then to test. mining methods and determine if these stresses could be modified to a

Jan 1, 1982

By J. Riefenberg

U.S. Bureau of Mines (USBM) researchers are developing a personal computer-based hazard mapping system for use in underground coal mines. Hazard mapping is rapidly gaining interest as delineating areas of possible instability is becoming more complex. The development of a hazard map is based on the consensus that combined effects of local and regional stresses, roof, floor, and rib quality, geology, faulting, presence of ground water, etc., all contribute to stability of the ground. In order to demonstrate the concept, a hazard map was developed that combined stresses anticipated to occur in a multiseam setting using numerical modeling, and the newly developed Coal Mine Roof Rating (CMRR) where roof quality ratings in untested areas were modeled using geostatistical methods. Ten borescope readings from an underground mine were used to compute CMRR's for the geostatistical analysis. CMRR's for the mine ranged from 57 to 77, and are considered in the moderate to strong range. A hazard map was developed by combining the stress effects of interseam mining, scaled to weigh equally with CMRR's, and CMRR geostatistical analysis results. This hazard map demonstrates a synergistic effect between the mining-induced stress fields and the roof quality ratings, indicating, as expected, a greater hazard index in areas of high stress and lesser roof quality.

Jan 1, 1994