Search Documents

By Ihsan Berk Tulu, Michael Sloan, Ted Klemetti, Michael M. Murphy, Gabriel S. Esterhuizen, Jame Sumner

"In this paper, the advantage of using numerical models with the strength reduction method (SRM) to evaluate entry stability in complex multiple-seam conditions is demonstrated. A coal mine under variable topography from the central Appalachian region is used as a case study. At this mine, unexpected roof conditions were encountered during development below previously mined panels. Stress mapping and observation of ground conditions were used to quantify the success of entry support systems in three room-andpillar panels. Numerical model analyses were initially conducted to estimate the stresses induced by the multiple-seam mining at the locations of the affected entries. The SRM was used to quantify the stability factor of the supported roof of the entries at selected locations. The SRM-calculated stability factors were compared with observations made during the site visits, and the results demonstrate that the SRM adequately identifies the unexpected roof conditions in this complex case. It is concluded that the SRM can be used to effectively evaluate the likely success of roof supports and the stability condition of entries in coal mines.INTRODUCTIONSince the introduction of roof bolts in the coal mines during the late 1940s and 1950s, roof bolts promised to dramatically reduce roof fall accidents (Mark, 2002). However, ground falls still remain a significant factor in underground coal mine injuries and fatalities. In 2013, ground falls accounted for 4 of the 14 fatalities and 166 of the 1577 reported lost-time injuries in underground coal mines (MSHA, 2015).The design of appropriate support systems requires the understanding of: 1) the variable nature of the rock mass, 2) the performance and characteristics of the roof support, 3) the interaction between the rock mass and the installed support system, and 4) the in-situ and mine-induced stress distribution around the excavation. Over the past 25 years, multiple design approaches have been used in coal mine ground control. The approaches include empirical mechanistic methods, empirical statistical analysis, rules of thumb, and numerical methods (Hebblewhite 2006). In the U.S., Analysis of Roof Bolt Systems (ARBS) can be given as an example of an empirical method. ARBS uses relatively simple equations to calculate the intensity of support provided by a roof bolt system and compares it with a suggested ARBS value (Mark et al., 2001). The suggested ARBS design equation is derived from an analysis of 100 case histories. The ARBS design equation is dependent on two parameters: depth of cover and Coal Mine Roof Rating (CMRR). More recently, a probabilistic design approach was developed by Canbulat and van der Merwe (2009) in South Africa. In this method, the variability of the rock mass, the mining geometry, and support characteristics are included in the analytical models. The major advantages of these two methods are: 1) they can be applied rapidly and easily, 2) complex rock mass/ roof support interaction mechanisms are represented with simple equations, and 3) they are supported by large databases. However, both methods generally ignore mining-induced stress distribution, details of the roof support system, details of the geological setting, and the interaction between the support system and the rock mass."

Jan 1, 2015

By Tom Barczak, Julian Restrepo, Zach Agioutantis

"The Alpha Foundation for the Improvement of Mine Safety and Health, Inc. (Foundation) was established as part of a Non-Prosecution Agreement (Agreement) entered in December 2011 by the United States Attorney's Office for the Southern District of West Virginia, the United States Department of Justice and Alpha Natural Resources, Inc. (""Alpha"") and Alpha Appalachia Holdings, Inc. This Agreement was related to the explosion at Upper Big Branch Mine, an underground coal mine owned by Performance Coal Company, a former affiliate of Massey Energy Company, which Alpha acquired in June 2011. Pursuant to that agreement, Alpha agreed to establish a trust to fund projects designed to improve mine health and safety by providing $48,000,000 into the trust. The mission and vision of the Foundation are as follows:Mission: To improve mine health and safety through funding research and development projects by qualified academic institutions and other not-for-profit organizations.Vision: To enable miners in the future to be free of work-related injury or disease by the implementation of the results of the projects funded by the Foundation and undertaken by the best researchers from any discipline that can contribute.The focus of the research effort is not limited to coal mine explosion prevention, and in fact encompasses the entire spectrum of health and safety, addressing issues in both underground and surface mining operations in all mining sectors. Four major focus areas are identified (see Figure 1): 1) Health and Safety Interventions; 2) Mine Escape, Rescue, and Training; 3) Safety and Health Management and Training; and 4) Injury and Disease Exposure and Risk Factors.The Foundation is seeking to expand the knowledge base of mining safety and health information that can lead to resolving complex mining problems. To that end, the projects funded by this effort are designed to provide a spectrum of knowledge potentially encompassing the following:• Surveillance data - Collect and analyze surveillance data that better documents the prevalence and trends of occupational safety and health across the mining industry."

Jan 1, 2016

By G. Skybey

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole. The DDM is currently being used successfully for long hole drilling in a number of collieries. A high degree of directional control has been achieved. Borehole trajectories were controlled to within +l¬2m of the planned path with intersurvey distances varying between 6 to 18 metres over distances up to 700 metres.

Jan 1, 1992

By Bo-Hyun Kim, Mark K. Larson

"While faults are commonly simulated as a single planar or non-planar interface for a safety or stability analysis in underground mining excavation, the real 3D structure of a fault is often very complex with different branches that reactivate at different times. Furthermore, these branches are zones of non-zero thickness where material continuously undergoes damage even during interseismic periods. In this study, the initiation and the initial evolution of a strike-slip fault was modeled using the FLAC3D™ software program. The initial and boundary conditions are simplified and mimic the Riedel shear experiment and the constitutive model in the literature. The FLAC3D model successfully replicates and creates the 3D fault zone as a strike-slip type structure in the entire thickness of the model. The strike-slip fault structure and normal displacement result in the formation of valleys in the model. Three panels of a longwall excavation are virtually placed and excavated beneath a main valley. The characteristics of stored and dissipated energy associated with the panel excavations are examined and observed at different stages of shear strain in the fault to evaluate bump potential. Depending on the shear strain in the fault, the energy characteristics adjacent to the longwall panels present different degrees of bump potential, which is not possible to capture by conventional fault simulation using an interface.INTRODUCTIONThis paper is part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bump-prone potential in highly stressed ground conditions. More specifically, this paper reports an exploratory effort with an unconventional approach using a numerical tool to try to better understand a possible scenario where bump risk might be increased—that is, a scenario involving a strike-slip fault. The objective is to assess whether a numerical tool might be useful or practical in forecasting bump potential associated with a strike-slip fault for a typical, structural geologic setting."

Jan 1, 2018

By Ximeng Li

The entries that are subjected to dynamic pressure are much more difficult to maintain due to repeated disturbance. A case study of an entry stress distribution was performed using the FLAC3D program. By analyzing the distribution of stress field around the entries, this paper provides guidelines for entry support design in the lower (#16) seam subjected to the repeated disturbance from longwall mining in the immediate overlying (#17) seam, 72ft (22 m) above. The results showed that there was stress superposition inside the barrier pillar in the lower seam, 15ft (5m) to 45ft (15m) deep, during development. The influence zone of the front abutment pressure in the upper (#16) seam was about 100ft (30m) outby the faceline. The stress-relieved zone was from 0 to 100ft (30m) inby the face. The area further inby the face (i.e., 230 ft (70 m) inby the face) was within the gob compaction zone. Along the face advancing direction, the affected zones of the entries in the lower (#17) seam that were subjected to the dynamic pressure from longwall mining of the immediate overlying seam could be divided into four stages: pillar development stress stage, front abutment pressure stage, unstable gob stage, and stable gob stage. Those entries within an area from 100ft (30m) outby to 100ft (30m) to 230ft (70m) inby the faceline should be reinforced with special supports. The numerical modelling matched the monitoring results well.

Jan 1, 2013

By Gerald I. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of the rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock ]avers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified, In order to determine the application of the drilling parameters for identifying rout rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble. and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation or, the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.

Jan 1, 2000

By Jun Lu, Greg Hasenfus

"In this paper, the mining experience and challenges for the first right-handed longwall panel in the Pittsburgh seam are introduced. The longwall headgate T-junction experienced very high face convergence (up to 2 feet), accompanied by roof sag, floor heave, and rib loading. The headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded.Different underground instruments, such as a roof scope, de-gas drill, tell-tale, laser meter, and Borehole Pressure Cell (BPC), were employed to explore the roof geology and to monitor the entry convergence and the stress changes in the pillar. In addition, the impact of other geologic factors, such as large overburden depth, laminated sandstone roof geology, soft floor, and large headgate equipment, were also analyzed. Subsequently, geotechnical solutions were provided to avoid or mitigate the impact of these challenging geologic factors.INTRODUCTIONIt is well known that high horizontal stress will affect the stability of roof, floor, and ribs within underground mines. In general, the headgate entries will experience stress concentration for the right-handed longwall face. On the contrary, the stress concentration will be in the tailgate entries for the left-handed longwall face (Hasenfus and Su, 2006). Without the stress shadow, the stress concentration in the headgate for the first longwall panel may be more significant (Figure 1).A mine in the CONSOL Pennsylvania Operation was extracting the first right-handed longwall panel in the Pittsburgh seam, which created high horizontal stress concentrations at the longwall headgate. Because of concern over soft wet floor within the syncline, floor coal had been left in place on development. Early on, upon retreat, the longwall headgate T-junction experienced very high face convergence, accompanied by roof sag, floor heave, and rib loading. The floor heave was exacerbated by the presence of floor coal, which buckled upward near the center of the beltline. Roof movement was occasionally aggravated by laminated roof conditions, but was kept in check by aggressive supplemental support including cable bolts, yielding props, cribbing, and roof mesh. Rib bolting and rib mesh helped to further maintain the entryway stability by keeping sloughage at a minimum. Nevertheless, despite the heavy support, headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded."

Jan 1, 2018

By S. Jayanthu

This paper presents analysis of strata behaviour with special reference to convergence and stress variation during an experimental trial of extraction of pillars with cable bolts as major support system in 6.5 - 8.0 m thick coal seam. Critical span for roof falls was estimated through empirical models and also evaluated by numerical models. In situ strata behaviour studies during 1992-96 for about 70 local/major falls revealed inadequacy of the available literature for interpretation and prediction of the roof falls. Convergence acceleration and variation of induced stress based on continuous monitoring data showed distinct anomalies and potential for better understanding of strata mechanics during pillar extraction.

Jan 1, 1998

By Robert Trueman

This paper details the results of an assessment aimed at understanding the shield loading mechanisms associated with strata-related issues on a longwall face. Shield load cycle analysis theories developed by the authors were used to quantify the interaction between the shields and strata. Shield pressure data was back-analyzed using a version of the Longwall Visual Analysis (LVA) software that has been extended to enable efficient load cycle analysis to be undertaken. The software outputs enabled the shield strata interactions to be characterized. The results of the analyses indicated that the major cause of the roof falls was high-level periodic weighting, resulting in periodic shield overload. Exploration borehole data was analysed to identify and characterize the overburden unit that was the likely cause of the shield overloading.

Jan 1, 2011

By Pengfei Wang, Guorui Feng

With increase of cover depth, dynamic incidents, such as large gateroad convergences and coal bursts, are frequently encountered when mining deep longwall panels. It would be more adverse due to large inclination of the coal bed. Because of the shearer and armored face conveyor (AFC) sliding downhill, toppling of shields, disconnection of AFC to the stage loader are related to it. Tangshan coal mine is a typical deep, inclined coal mine situated in the east of China. The split-level longwall panel layout is being adopted for mitigating problems above, where tailgate entries of longwall panels are driven below gob edge and along the floor, while headgate entries are driven along the roof. Wire mesh and steel sets have been used empirically for support for tailgates for about a decade, which reduces the tunneling speed. In view of this fact, the paper serves to investigate the proper adjustment of the tailgate locations and to analyze the resulting stress and yield conditions according to support strategy. First, field measurements and observations were carried out. Stress data distributed within surrounding rock mass were obtained, especially within the roof since the roof consists of only a coal sheet with a thickness of 2–4 m. Roof pressure of the tailgate represents the pressure at the gob edge since it is below the gob edge. The convergence data were also collected. Numerical modelling using FLAC3D™ was conducted and validated by side abutment stress data. The double-yield constitutive model was used to simulate the gob. The finalized tailgate layout and design were determined through comparison of three scenarios. The research in this paper can help engineers choose the proper tailgate layout and support strategies for coal mines that are going to adopt a split-level longwall panel layout for mining deep, inclined longwall panels.

Jan 1, 2018

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By Morgan M. Sears, Gamal Rashed, Jim Winfield, Brent Slaker

"Over the past decade, ground falls have resulted in five fatalities, representing over 40% of all fatalities occurring in underground stone mines in the United States. In conjunction with recent high-profile pillar collapses, the need for further ground control research in the nation’s stone mines is evident. Ground conditions are growing more difficult. Therefore, this research is focused on deep cover, steeply dipping, and multi-level underground nonmetal mines. The objective of this paper is to introduce a geomechanical study of pillar development in a steeply dipping limestone deposit. To accomplish this, a numerical model was developed using input from modified laboratory test data and in situ stress measurements provided by the mine to simulate the development of a pillar under these conditions. The model was then verified against field observations and stress mapping. The calibrated model was then used to calculate the estimated stresses in the pillar and immediate roof as development progresses around an instrumented pillar.INTRODUCTIONGround falls represent a significant hazard in the nation’s underground stone mines. In response to recent large-scale pillar collapses, as well as stakeholder interactions, researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at mines operating in challenging operational environments. These include deep-cover, steeply dipping, and multi-level mines where there is the potential for an increased risk of ground failure. The Pleasant Gap Mine, shown in Figure 1, operates in the Valentine Formation, which is typically light grey, extremely fine-grained limestone, and approximately 21.3 m (70 ft.) thick. The Centre Hall Formation makes up the immediate and main roof members and is approximately 9.1 m (30 ft.) thick, consisting of medium-dark-gray limestone (Murphy et al., 2018). Situated in a syncline, the top of the Valentine Formation dips at approximately 19° with a strike of approximately N54E in the area of interest (see Figure 2)."

Jan 1, 2018

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

By David F. Gearhart, Khaled M. Mohamed

"Trusses are primarily used as passive roof supports in coal mines. They are constructed of three main parts: two grouted bolts installed at opposing forty-five degree angles into the roof so that they are anchored over the ribs and a cross member that ties the angled bolts together. There is also hardware used to assemble these components. The capacities of the angled bolts are typically 30 to 40 tons and the tensile capacity of the cross member is also 30 to 40 tons. Importantly, the direction of the immediate roof loading on the cross member is unlike the direction of the loading on the angled bolts. The load on the cross member is transverse to the longitudinal axis instead of along it, and therefore the cross member is loaded in the weakest direction.Previous tests conducted on truss systems applied loads such that the increasing tension in the two diagonal bolts increased the tension in the horizontal cross member, resulting in a stiff response. By contrast, if the load is applied directly to the cross member, which then transmits those forces to the diagonal bolts, it results in a much softer response.Based on this difference, laboratory tests to apply transverse loads and measure the vertical load capacity of three different types of cross members were conducted using the Mine Roof Simulator (MRS) located at the National Institute for Occupational Safety and Health (NIOSH) in Pittsburgh. The length of the samples was about 16 feet. Single-point load tests, with the load applied in the center of the specimen were conducted to verify the performance of the test arrangement and the finite element models. Double-point load tests, with a span of eight feet, were also conducted. This arrangement replicates the performance of the cross members with a distributed load. Both of these test arrangements were conducted on one-inch-diameter threaded steel bars and 0.7-inch-diameter cable and 0.6-inch-diameter cable cross members.For the single-point load configuration, the yield of the one-inch bar was nominally 22 kips of vertical load, achieved at 17 inches of deflection. For both sizes of the cable cross members, yield was not achieved even after 18 inches of deflection. Peak vertical loads were about 20 kips for the 0.7-inch cables and 15 kips for the 0.6- inch cables. For the double-point load configurations, the one-inch bar cross members yielded at 33 kips of vertical load and 10 inches of deflection. The 0.7-inch-diameter cable cross members broke strands at 30 kips of vertical load and 10 inches of closure, and the 0.6-inch-diameter cable cross members broke strands at 25 kips of vertical load and 10 inches of closure. Finite element models of each of the six different configurations were developed and show the variation of the vertical capacity of the cross members and the difference of the behavior of the bar versus the cables."

Jan 1, 2015

By Yi Luo

The severity of disturbances caused by longwall mining subsidence to various residential structures can be re¬duced. The success of such mitigation efforts depends on accurate subsidence prediction, correct assessments of the subsidence influences, and careful design and implementa¬tion of the proper mitigation measures. This paper presents the systematic approach involved in the subsidence mitiga¬tion efforts with a case demonstration.

Jan 1, 2003

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By Kristine L. Pankow, Keith D. Koper, Michael K. McCarter, Jared R. Stein

"The Wasatch Plateau region of central Utah contains a number of active underground coal mines in an area of well-documented natural seismicity. As a result, there are several hundred seismic events recorded in this region every year that may or may not be attributed directly to mining activity. Previous studies have linked the majority of this seismicity to mining activity through various means, but have not attempted to develop a method for categorizing individual events within a seismicity catalog. This study uses both relative relocation and waveform cross-correlation to separate events based on hypocentral depth and waveform similarity, respectively, in the area surrounding a single longwall coal mine within the Wasatch Plateau. We conclude that relative relocation can help with depth discrimination, but there are some unavoidable limitations caused by sparse seismic network coverage. The cross-correlation technique is more promising, with the ability to group events by waveform similarity and track mining progress over both space and time. With cross-correlation based clustering, we confirm that the vast majority (97.6%) of events in the study area are directly related to mining activity, but that a small population of natural seismicity is present as well. Eliminating this natural seismicity from the catalog of seismic events, leaving only those events related to mining, can give operators valuable information about the changing conditions as mining progresses and eliminate concern over events unrelated to mining activity.INTRODUCTIONA number of underground coal mines are located in the Wasatch Plateau region of central Utah, and have been in operation since the late 1800s. This activity has resulted in a well-known history of mining induced seismicity (MIS) (Wong, 1985). Additionally, this area is situated near the border of the Basin and Range and Colorado Plateau physiographic provinces, where naturally occurring tectonic earthquakes also occur (Arabasz et al, 1980). Seismicity separating these physiographic provinces is part of a larger band of seismic activity known as the Intermountain Seismic Belt (ISB) that runs from Montana to Arizona and cuts through the western boundary of the central Utah coalfields (Smith and Arabasz, 1991) (Figure 1)."

Jan 1, 2015

By Kot Unrug

The selection of tensioned versus non-tensioned roof bolts, for primary coal mine roof support, has been debated for well over 25 years. The wide spread use of fully grouted rebar marked the beginning of the discussion of the relative importance of bolt tension and the resultant immediate roof compression. The focus is on roof conditions encountered in coal mines however the discussion may be extended to hard rock mines as well. The theoretical bases for both systems are presented, with the analysis focused on the bolt's ability to actually fulfill the theoretical assumptions. Of specific concern are assumptions about bolt tension upon installation and the likelihood of maintaining useful bolt tension over time. The usefulness of tension roof bolting is limited by the mechanical interaction of roof bolt assembly and the rock, which may be valid at the time of installation only. Ambient mine atmosphere and fluctuation in moisture content changes the physical condition of rock, which may have a significant impact on the effectiveness and longevity of bolt tension. Changes in the material properties of the surface of the immediate roof can invalidate the assumptions, which were made in the design stage of roof support system. This means that the roof support in the long term excavations may be inadequate requiring costly rehabilitation. The presented arguments are illustrated with the examples of some relevant experimental data. Tension primary roof bolting is recommended where the immediate roof is: ? Stiff with a high modulus of elasticity ? Surface layers are continuous and fairly thin ? Not easily weathered

Jan 1, 2004

By Yongping Wu

Taking the longwall mining face area in a steeply dipping seam as the research object, the stability of an asymmetrical rock mass structure is analyzed using shell theory and masonry beam theory. The results show that an asymmetrical shell structure is formed at the top strata of the mining stope and its magnitude is mainly determined by the mechanical characteristic of the overburden strata of working face, mining space size and so on. Localized instability of the shell structure is the main factor that leads to the overall structural instability in the stope. The instability modes includes: the shell roof instability dominated by tensile failure, the shell shoulder instability initialized by compression-shear failure, and shell bases composite instability occurs in tensile and compression-shear modes. The shell structure stability dedicates rational strata control measures to choose, and the caving height of overburden strata is the key for shell structure instability.

Jan 1, 2013