Search Documents

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold masses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By Thomas A. Wheeler

The reagents commercially used in coal flotation and their roles are reviewed and discussed According to their function the reagents are divided into often overlapping groups: 1. Collectors 2. Frothers 3. Conditioning Reagents Frothers have by far the largest effect on the amount of coal recovered They act not only in their traditionally accepted function of “bubble makers”, but in coal flotation they serve in a seldom acknowledged role of collectors. A lab flotation study on four samples of different coal ranks shows how these react to various frother families and proves that no froher is the optimum reagent for all types of coal. The advent of new technology in flotation equipment in the past decade has resulted in various novel designs of column cells, Jameson and Centrifloat™ cells, air-sped hydrocylones, etc. All should require special frothers or blends of frothers to meet their specific needs.

Jan 1, 1994

By F. Gonzalez, A. Zambrano, J. Schwoebel, S. Kravits

Significant lost time delays were experienced by Carbonifera de Nueva Rosita, S.A. de C.V. ("CNR") during mining development of the Pasta de Conchos Mine ("the Mine") near Nueva Rosita, Coahuila, Mexico. Furthermore, methane gas concentration in the return air course had exceeded 1.0 percent. Resource Enterprises, Inc. ("REI") was contracted by CNR to recommend an approach to reduce methane emissions at the Mine. In order to recommend a degasification approach, REI and CNR obtained geologic and reservoir characteristics of the Double coal seam, Olmos Formation. A vertical core hole was drilled to obtain core samples to determine gas content (average 8.4 cm3/gm) and to conduct a slug test to estimate permeability (34 md). This information was used to simulate gas productivity and drainage effectiveness. The simulation indicated that underground horizontal boreholes would remove significant quantities of gas in advance of mining in a reasonable period of time. Based on the results of the simulation study, an underground degasification drilling program was initiated at the Mine. In a six month period, five long in-mine degasification boreholes were drilled in advance of CNR's three to five years mining projections. Peak gas production from the five boreholes (approximately 2,750 cumulative meters) had exceeded 45,000 m3/D. Results to date have indicated a general reduction in methane concentration in the return air course below 0.8 percent.

Jan 1, 1993

By Stanislaw Siewierski

One of the major problems in the exploitation of deep copper ore deposits in the Legnicko-Glogowski Copper Field is ground control and, in particular, roof control of the headings. The depth of copper deposits ranges from 600 to 1200 m. The parameters of ore-bearing rocks and the surrounding rocks show considerable variance of strength properties along the mining thickness (Fig. 1). The roof of the openings exploitation headings consists of dolomite-calciferous rocks. The roof strata consist of layers, the thickness of which vary from several centimeters to 0.6 m (sometimes to 1.0 m). These strata differ in strength and are characterized by igneous and sedimentary discontinuities. On the basis of studies in structure, properties and geological mining conditions of the roof strata in Polish copper mines, the method of roof classification has been developed. (1) This method uses the stability index "L" of the roof, calculated from [ ] The value of "t" ranges from 0, l to 0,8. Based on the value of "L", four classes of the roof (Table 1) corresponding to different degrees of fall hazard have been developed. The mining of copper ore deposit is carried out by a single lift room-and-pillar mining system or a two-stage room-and-pillar system with roof caving. (3, 4). The single lift room-and-pillar mining system is most often used. It consists in working of the deposit of 2.5 to 4.5 m mining thickness, 150-350 m long mining line, consisting of parallel room faces 6 m wide with pillars 5.7 or 16 m wide. As the mining line advances, cross-cuts joining individual rooms are made, thus forming support pillars 3x5, 7x7, 5x16, and 7x16 m (Fig. 2). The two-stage system (Fig. 3) mines the deposit with rooms 6 m wide into blocks 25 x 35 x 25 x 45 m. During the second step these pillars are worked with rooms and cross-cuts into pillars about 3 x 4 to 4 x 5 m (retreat mining). The pillars are crushed just before the fall of the roof. The maximum opening of workings in the two-step system is about 10 m, i.e. one belt entry and one row of bearing pillars. In single lift room-and-pillar systems it is about 35 m., i.e. three belt entries and three rows of bearing pillars. The support of the headings consists of expansion bolts 1.6-1.8 m installed in a bolting pattern 1.1 x 1.5 m. In both systems the fall step is about 10 m, i.e. the width of a belt and a bearing pillar. The Indications of Rock Mass Pressure Individual Dog Heading Individual dog headings are set wide apart from each other in the unmined ore deposit area where there is no interaction of headings. The indication of rock mass pressure are, in such cases, limited to the deformations and damage of side walls. Radiometric studies of rock mass loosening showed that the maximum range of lifts in side-walls immediately after web was 2 m (4,5). In the course of time the cracked side rocks fall off, thus widening the heading. The morphology of side-walls is influenced by the location of the heading in relation to clump layer/tarry. This layer is characterized by a weak strength and "lubricating" properties. The location of the heading in

Jan 1, 1982

By Carlos Tarazaga

Progressive Design-Build (PDB) is an emerging variation of alternative delivery programs in the underground construction industry. PDB refers to the way a construction project design is developed by the Owner and the Design-Builder in a step-by-step process. According to the Design-Build Institute of America (DBIA), Progressive Design-Build allows the design and construction team to collaborate during the earliest stages of project development. This enables engagement between the three key players in a construction contract: the owner, the designer, and the contractor. Is the PDB the best alternative program delivery for large contracts? What is the perspective of the private sector? This paper will provide an overview of the different alternative delivery programs used in the underground industry, pros and cons of each of programs, and the perspective of the designers and contractors. The paper will focus on how the PDB works, reasons why owners should consider PDB for their projects, best collaboration strategies among owners, designers, and contractors to deliver a successful project, and how to manage the project risks using a PDB method.

Jun 13, 2023

By N. Standish

Leonard and Newman (1989) describe concepts and plans of their forthcoming project designed to increase the bulk density of broken coal at various stages of its production and handling. This is an excellent idea and something that will certainly be useful to the coal mining industry worldwide. The authors seek to achieve bulk density increase by "reducing oreliminating, through chemical additives and engineering design, particle voidage and enhance particle consolidation trickling between the point of breakage (at the face) and loading (in the shuttle car) to increase coal bulk density and productivity." In the paper, they present some supporting results of bulk density versus moisture, with or without oil addition, from the steel industry research. Unfortunately, the paper contains many misconceptions and half-truths that detract from an otherwise excellent objective of the project of increasing bulk density by reducing particle voidage -"the bottom line evaluator." Correct.

Jan 1, 1990

By C Rutter, N Shea, K Kolobe

The Henderson mine, a panel cave mine in Colorado, has undergone multiple ventilation system changes to meet dynamic airflow needs. This paper explains the ventilation designs for different production panels, the challenges faced, and the modifications made to optimize the ventilation systems. The study highlights the importance of a robust ventilation system for safe and productive mining.

Mar 2, 2022

By Alfred W. Hefferan

A longwall face conveyor system serves the primary function as all material handling systems; i.e., to transport material between the source and its destination. However, the conveyor system must provide many other functions as opposed to the traditional belt conveyor system. In this paper, we will attempt to contrast the longwall face conveyor system with a belt conveyor system. In addition, the unique problems encountered along with the solutions to these problems will be covered. Table 1 lists the characteristics required of each conveyor system. The table demonstrates the contrast in the two systems. Both must be designed specifically to encounter its unique problems. The balance of this paper will explain how the longwall face conveyor is designed to address its requirements.

Jan 1, 2000

By Thomas J. Rudolphi

Efficient transport of bulk materials by belt conveyor systems is an important engineering design issue, especially as conveyors become longer and power requirements increase. It is well known within the industry that the parasitic energy loss of a belt conveyor, due to the indentation of the idlers into the belt backing material can be upwards of half the total energy required to drive it on a horizontal flight. Other loss sources includes the rolling resistance of the idlers, belt/roller misalignments, material trampling, frictional and acceleration losses on loading, etc., but energy absorbed by indentation of the belt backing as it passes over each successive idler is the dominant power consuming factor. INDENTATION LOSS MODELS Models to predict the rolling resistance of a cylinder (idler) on a viscoelastic foundation (backing material) have been available for some time. As a contact problem, it is nonlinear (contact length or indentation depth is a dependent on the load and vice versa) in load/deformation response. Rubber backing material is generally assumed to behave as a linear viscoelastic solid, even though it is known that most rubber compounds retain linearity only at very low strains. Because completely general solutions are impossible, practical solutions require simplifying assumptions. Those assumptions relate naturally to two separate pans of any analytical model: I. The deformation model-aspects of the problem relating to the geometry, boundary conditions and kinematics of how the material deforms. 2. The material model-aspects of the problem relating to the material properties, or constitutive relationships, i.e., the stress/strain relationships.

Jan 1, 2008

By C. J. Bise, D. A. Poukhovski

Hazard recognition and prevention of accidents are two components of the 30 CFR 48 training requirements, which are mandated for new miners and newly employed experienced miners. These components are also part of the annual refresher training course required of all miners. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine and shall include a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition presents a particular challenge to safety-training specialists, because they are often limited in their ability to adequately gauge the level of awareness of the individual prior to training. Further, they must also assure that the training is relevant and presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics, because it can be used in pretraining and posttraining modes for assessment of training effectiveness, in addition to its use as a presentation tool. This article presents a recent approach, developed at The Pennsylvania State University, that applies the technology for the assessment and instruction of accident prevention through hazard recognition. The application is prepared for surface coal mines.

Jan 1, 1999

By A. W. Wensel

The adsorption behavior of sodium oleate on brucite, Mg (OH)2, has been studied by Fourier transform infrared spectroscopy. Both internal reflection and diffuse reflection (DRIFT) methods were used to characterize the adsorbed oleate on brucite. DRIFT measurements were shown to be quantitative, and an equilibrium adsorption isotherm was obtained. The conformational behavior of the adsorbed oleate was investigated as a function of adsorption density. It was found that at sub-monolayer coverage the alkyl chains of the adsorbed oleate had more ?gauche? character than at multi-layer coverages. Also, DRIFT spectra revealed that the adsorbed species were magnesium dioleate. For internal reflection measurements single crystals of MgO were hydrolyzed to form a thin Mg (OH)2 layer.

Jan 1, 1994

By R. E. Miller

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By P. R. A. Andrews

Magnesite, brucite and dolomite occur widely throughout Canada, but deposits of economic significance are found only in Quebec, Ontario and British Columbia. Magnesite occurs in all three provinces, brucite in Quebec and Ontario and dolomite in Ontario. Beneficiation of refractory magnesium minerals has been the subject of many investigations at CANMET and the former Mines Branch. Twenty-three magnesite, four brucite and nine dolomite evaluation studies were conducted between 1920 and 1974. A review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and flotation data.

Jan 1, 1995

By G. E. S. Valadao

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake pore microstructure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 µm, length of 500 µm and height of 4000 µm. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: I) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method, 2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4) some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By Cameron Dunn, Callum Fryer, Carmen Hu, Craig Sewell, Peter Stakne, Andrew Raine

The Woodsmith Project is located in north-eastern England within the North York Moors National Park. The strata contains the world’s largest known high-grade Polyhalite resource of around 2.66 billion tonnes. The Project was initiated by York Potash Limited (YPL), a subsidiary of Sirius Minerals plc., but in March 2020, a takeover was completed by Anglo American, one of the largest mining companies in the world. Polyhalite is an evaporite mineral and contains essential nutrients required for plant growth. The Polyhalite will be extracted via two deep mine shafts and transported underground from the mine site to a Materials Handling Facility on a Mineral Transport System (MTS), which comprises a high-capacity conveyor belt system located within a 4.9 m ID tunnel. In 2018, STRABAG were awarded with the design and construction of the MTS tunnel and associated infrastructure, including the high-capacity conveyor system. The scope of work consists of 300 m of open cut, 100 m SCL tunnel, 36.5 km TBM drive (originally anticipated as three separate TBM drives) along with a network of underground caverns at the Woodsmith Mine. The construction of two 380 m deep intermediate access shafts was later awarded as Amendments to the Contract. The tunnel is constructed using a Herrenknecht Single Shield TBM. As a result of how the various elements of the project have developed over time, the first TBM drive has been extended to ~29 km making it the worlds longest single heading TBM Tunnel when complete. The option of completing the entire tunnel length with a single heading TBM drive is currently being assessed by Anglo American and STRABAG. This unprecedented tunnel length requires two intermediate shafts to provide essential access and services, the first intermediate shaft is at Lockwood beck (LWB) and the second is at Ladycross (LDX). The LWB shaft has been constructed utilising the innovative Blind Boring technique never used before in the UK. This paper will explain the methodology and technical risk management associated with this technique. The authors believe that the collaborative approach between all contract partners is and continues to be the important contributor for the success of this project.

Jun 13, 2023

By E. W. Geist

This paper is presented from the viewpoint of the mill operator and maintenance supervisor. Its purpose is to highlight the things that have been accomplished by the mill designers to lighten the load for the maintenance superintendent and to reduce the overall costs for the plant operator. The complexity of plant design, the civil and structural engineering problems encountered when the satisfactory maintenance layout is accomplished are appreciated, and the writer is fully aware of the complexities of these problems. However, it is not the purpose of this particular paper to dwell upon these problems, nor to emphasize or de-emphasize the problems of the civil, mechanical and electrical engineers. It is simply that the paper will attempt to review what these people have accomplished in spite of the many technical problems. This paper then is prepared with the operator and maintenance people?s viewpoint. What is their definition of design for maintenance? It is the writer's interpretation that the various design concepts which mean improved maintenance are such items as (I) maintenance areas, (2) laydown space for maintenance materials in specific maintenance jobs, (3) the inclusion of bridge cranes in the plant and specific design of the craneways to accomplish flexibilities for the cranes, and (4) the location of the piece of equipment to allow maintenance people to work around the equipment - - - this specifically includes the orientation of the particular piece of equipment.

Jan 1, 1967

By LUKAS FAHLE, JURGEN F. BRUNE, ANDREW J. PETRUSKA, ELIZABETH A. HOLLEY, Gabriel Walton

Adverse ground behavior events, such as convergence and ground falls, pose critical risks to underground mine safety and productivity. Today, monitoring of such failures is primarily conducted using legacy techniques with low spatial and temporal resolution while exposing workers to hazardous environments. This study assesses the potential of novel simultaneous localization and mapping (SLAM)-based light detection and ranging (lidar) data quality for rapid, digital and, eventually, autonomous minewide underground geotechnical monitoring. We derive a comprehensive suite of quality metrics based on tests in two underground mines for two state-of-the-art mobile laser scanning (MLS) systems. Our results provide evidence that SLAM-based MLS systems provide data of the quality required to detect geotechnically relevant changes while being significantly more efficient for large mine layouts when compared to traditional static systems. Additionally, we show that SLAM-specific processing can achieve an order of magnitude better relative accuracy relevant for change detection than quality metrics derived from traditionally deployed tests would suggest, while reducing SLAM-drift error by up to 90 percent. In collaboration with an operating block-caving mine, we confirm these capabilities in field tests on a minewide scale and, for the first time, demonstrate methods of rockfall detection using MLS data. While more work is required to investigate optimal collection, processing and utilization of MLS data, we demonstrate its potential to become an effective and widely applicable data source for rapid, accurate and comprehensive geotechnical inspections.

Jan 1, 2023

By S. Norman Kesten

The Resource Conservation and Recovery Act, commonly known as RCRA, which amends the previous Solid Waste Disposal Act, was signed into law on October 21, 1976. Members of the mining industry began their contacts with EPA in this area two to three years before the Act finally was passed, and that seemed and probably was all to the good. We reviewed and commented upon their studies and in general tried to acquaint them with the peculiarities and the uniqueness of the wastes generated by our industry, of which they were abyssmally ignorant. I suppose we thought that through the bureaucracy we might have some influence upon the provisions of the solid waste legislation that was being bandied about on the hill. Certainly the industry, in general, did very little direct lobbying, as I recall, and there were several reasons for that. For one thing we conceived that the legislation was aimed at the chemical industy and believed that if their people looked after their interests, ours would be safeguarded automatically. Also, the Federal Land Policy and Management Act (FLPMA) was heating up at the same time and, in fact, was signed into law on the same day. In addition, a great deal of lobbying activity was required by amendments of the Clean Air Act and Federal Water Pollution Control Act that were being put together in Congress. These were conceived to be of far greater importance to our industry than a bill to control mostly chemical wastes and, in fact, new bills in both areas became law the following year. Finally, the solid waste bill, RCRA, was patched together by committee staffs over one weekend and was reported out by a conference committee rather hurriedly. Some little goodies about mining were almost after-thoughts in this process.

Jan 1, 1981

By André Vien, Robert Edwards, Rob Perry

A metallurgical control application can only succeed if the system's lowest common denominator, its instrumentation and regulatory control is implemented and maintained correctly. This paper describes the basics of regulatory control implementation including some practical guidelines for instrumentation installation, operator interface design, loop tuning, and continuous loop performance analysis. Tuning and analysis techniques are illustrated by step-by-step industrial examples. A small investment in basic control pays dividends in better overall plant performance and provides a solid foundation for advanced control efforts such as expert systems.

Jan 1, 2000

By Kristian E. Waters, Hao Ma, Haibei Wang

Heavy metal ions exist in waste effluents including mining tailings, manufacturing discharges, and smelting and metal plating process wastes. Various methods are available to treat industrial effluents containing high levels of metal ions, but when confronted with wastewater that has low metal ion concentration below 500 mg/L, most techniques suffer from low removal or separation efficiency as well as high operating cost. ELM-based techniques can be used to solve these problems.

Apr 1, 2023