Search Documents

By Charles F. Herbert

It is difficult to decide who most deserves credit for discovery of a mining district that has produced over 19.8 Mg (7,000,000 fine oz) of gold and still contains a large reserve of low grade ore. Fred Culver may have made the first discovery. In the summer of 1867, the ship's log of the Hudson's Bay Co.'s steamer Otter stated that Fred Culver had been found nearly lifeless from wounds, without provisions, but with some 2.3 kg (80 oz) of rough, placer gold in the bottom of his canoe; he told of finding a rich creek and an attack by Indians that caused the death of his two companions. The place of rescue was about 24 km (15 miles) southeast from the present site of Juneau. Possibly John Muir, the hero of modem environmentalists, should be given important credit. In 1879 he reported finding mineralization along what later became to be known as the Juneau Gold Belt, and it was his report that induced the cantankerous German mining engineer, George Pilz, to grub- stake some of the prospectors who had drifted into Sitka from the declining gold placers of Cassiar, British Columbia. Pilz also offered rewards to Indians who might report gold discoveries.

Jan 1, 1990

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By C. Cardoso, G. Bermudez, A. Jalili

Bigger flotation cells can result in larger froth surface areas and longer froth transport distances, this has been credited to impact froth recovery. Thanks to recent advancements, the newer flotation machines can be designed with different launder and crowder arrangements to enhance froth management. Nevertheless, lower head grades, complex ores and even larger mechanical flotation cells can lead to insufficient froth collection, even if the cell is equipped with the most recent flotation advancements like the center launder design. Aforementioned issue can become critical at the end of the flotation row. Increased crowding has been proven to be a solution to overcome inadequate froth recovery. However, scaling-up crowders for larger flotation cells can rise challenges, particularly in terms of structural limits and design for service. This paper presents the development journey for the Spider Crowder Upgrade, an advancement to improve froth collection in large flotation cells that are already equipped with center launders.

Feb 1, 2024

By J. A. Organiscak

Enclosed cab filtration systems are typically used on mobile mining equipment to reduce miners? exposure to airborne dusts and diesel particulates generated during mining operations. Various filter configurations can be used within the heating, ventilation, and air conditioning (HVAC) systems of cabs to remove the airborne contaminants. The air cleaning performance of cab filtration systems is highly dependent on the efficiency of the air filters, the number of filters used, and their placement within the HVAC system. This paper shows how to mathematically model cab filtration systems and illustrates a methodology for developing other cab filtration system design models. Node diagrams of several filtration system circuits are illustrated with their mathematical models at steady state airflow and concentration conditions. Laboratory and field data are presented to demonstrate the validity and utility of modeling enclosed cab air cleaning performance. The paper concludes that incorporating multiple filters throughout the HVAC system improves the air cleaning performance and robustness of the cab filtration system design.

Feb 23, 2014

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A three-stage fluidizing-bed process consisting of chlorination, selective oxidation and sulfur chloride conversion was tested for processing chalcopyrite concentrate. It was found that the use of excess oxygen was essential for the stable operation of the oxidation reactor. The excess-oxygen gas inevitably causes the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and selective oxidation steps with separate flow paths of the fluidizing gases, thereby, preventing the passage of excess-oxygen gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratoryscale fiuidizing bed setup.

Jan 1, 2002

By R. Fernando

"The Office of Mine Safety and Health Research (NIOSH-OMSHR) currently is leading an effort in the development of the next-generation self-escape apparatus as part of the research imperative directed by the MINER Act of 2006. A multifaceted contract program over the past 3 years delivered key components and base breathing modules to form the basis for developing backpack and vest-style versions of dockable self-contained (closed-circuit) self-escape respirators with hoods (CCMERs). This paper outlines the current status in developing the CCMER that incorporates a docking and switch-over valve (DSOV) for seamless transfer from one breathing device to another, and a hood with an inner mask and speech diaphragm (HMC) for ease of donning, ease of use, and communication ability. Three versions of the CCMER are being pursued, namely: the CCMER-B, which can be worn as a backpack and incorporates the features of a miner’s belt; the CCMER-V, which is worn similar to a miner’s vest and attaches to a miner’s belt; and the CCMER-C, a breathing module cached along the escape route that can be docked to the -B and -V versions. Human factors considerations are a key element in the CCMER design, as it is to be continually worn by the miner while underground, and must be readily accessible for deployment when needed. The CCMERs are designed to be capable of being certified to 42 CFR part 84 standards, including sub-part O for mine use, and to meet MSHA permissibility regulations for use in underground mines. They are sized for sufficient oxygen capacities (Cap 2 and Cap 3 as defined in sub-part O) to yield a duration that is of practical use in a mine escape scenario. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) is leading the development of self-escape apparatuses to provide breathing gas to mining personnel operating in the event of an emergency in various capacities underground in environments containing hazardous gas components. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) and input from the mining community called for the need to move Self-Contained Self-Rescuer (SCSR) technology to a next-generation status. In response to this need, NIOSH’s Office of Mine Safety and Health Research (OMSHR) established a strategic plan to develop key components and devices with help from external experts knowledgeable in breathing apparatus designs. The US Navy was identified as a key expert in this field through its extensive experience in diving apparatus and life support systems, and development work commenced through Inter-Agency Agreements with OMSHR. A contracts program was also launched with industry experts specializing in this field. This paper outlines the current status in developing the Next-Generation Closed-Circuit Mine Escape Respirators (CCMERs) that could be used for surviving and escaping from a mine following an emergency that renders the mine atmosphere irrespirable."

Jan 1, 2016

By S. Chander

A comparison of gold, platinum and sulfide ion selective electrodes was made for determination of Eh in solutions containing hydrosulfide ions as a model system. The comparison was made in terms of the accuracy of the measured response, response time, pH dependence, and reproducibility of measurement. The sensitivity of each electrode towards changes in hydrosulfide ion concentration was measured in terms of the change in measured Eh per decade change in concentration. On the basis of a detailed investigation of the electrode processes occurring at the surface of gold and platinum electrodes, it was postulated that within the pH range investigated these electrodes respond to changes in the hydrosulfide ion concentration in solution. In comparison, the sulfide ion selective electrode is known to respond to changes in the sulfide ion activity in solution. Although the potentials measured with gold and platinum electrodes were mixed potentials, pretreatment procedures can be used to obtain a signal suitable for process control. For control of hydrosulfide ions in flotation pulps, the use of a gold electrode pretreated at 1.0 V with respect to a standard hydrogen electrode is recommended.

Jan 1, 1992

By L. S. Gertsch, M. Z. Abu Bakar

The research presented here is part of a project to quantify the differences in the mechanical excavatability of rocks in dry and water-saturated conditions. A series of full-scale laboratory linear rock cutting tests were carried out with a long-bladed single disc cutter on dry and water-saturated sandstone blocks. The muck collected from the cutting tests was analyzed to establish a link with the specific energy (SE) of the operation. The coarseness index (CI), a non-dimensional parameter, was found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n was observed between SE and CI. The power n of the relationship for both dry and saturated rock was much lower than found in previous studies. The exponent n is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI was lower for saturated rock than for dry rock, at the same time, saturated rock cutting was found to be less energy-intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate, discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By K. Huttu, A. van Wageningen

"The Kittila underground mine is extracting one of the largest known gold deposits in Europe and has an estimated mine life through 2034. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. The ore at the Kittila mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulphide minerals – arsenopyrite and arsenic-rich pyrite. The orebody consists of a complex pinch-and-swell structure including up to 100 different gold mineralization lenses. Fluctuating gold prices and other economic considerations increase the need to maintain and update the mining plans more frequently. Over 3,000 stopes need to be designed and optimized once a year for the LOM-plan and more frequent updates are needed for mid- and short term plans as well as production studies. As a large part of ore body is very sensitive to cost and gold price changes, stope optimization is crucial to find the best possible production scenario for every moment. Kittilä has gone through several methods for stope design and optimization. Most recently the Deswik Stope Optimizer (Deswik.SO) has been successfully used. Dewsik.SO has helped Kittilä to design and optimize stopes in a timely and cost efficient manner. Together with the Deswik suite of planning tools, reliable and auditable plans are created. This paper describes the methods used for stope design and optimization at Kittilä. THE KITTILÄ MINE The Kittila underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittila achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two open pits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small open pits will mine any remaining near-surface reserves in the future. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. With a mine life estimated through 2034, Kittila is Agnico’s longest-life mine. The mine’s proven and probable reserves contain 4.7 million ounces (32 million tonnes at 4.6 g/t gold). Ore has been mined from underground since 2010. The original 3,000-tonne-per-day operation underwent an expansion project to increase the throughput capacity of the mill by 1,000 tonnes/day, starting by the end of 2014. The region around the Kittila mine is underlain by mafic volcanic and sedimentary rocks of the Kittila Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle's Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between iron-rich and magnesium-rich rocks lies a 100- to 200-metre-thick structural zone known as the “Suurikuusikko Trend”. This trend hosts the Kittila deposit, where multiple mineralized zones have been traced over a strike length of more than 25 kilometres."

Jan 1, 2015

By M. Soya, M. Imazu, Ö. Aydan

"SUMMARY Taru-Toge tunnel is being constructed using drilling-blasting technique as a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan. The maximum overburden is about 400 m. The authors have been carrying out a monitoring program to measure dynamic and multi-parameter responses of tunnel during and soon after the blasting operations using a multi-parameter monitoring system (Acoustic Emissions (AE), Electric Potential (EP), Temperature (T), Humidity (H) and Air Pressure (P)) and stand-alone type compact accelerometers developed by the first author. The measured response involves dynamic vibrations and other measurable parameters caused by blasting as well as by stress-redistribution around the tunnel face. This is one of the first attempts in the world to measure the response of rock mass caused by blasting at a very close vicinity of the tunnel face. In this paper, the authors present the outcomes of this unique monitoring study on the dynamic responses of the Taru-Toge tunnel during excavation and discuss their implications in actual applications. INTRODUCTION The real time monitoring of the stability of tunnels are of great importance when tunnels are prone to failure during excavation such as rockbursting or squeezing (i.e. Aydan et al. 1993, 2001). Experimental studies by the authors showed that rock indicates distinct variations of multi-parameters during deformation and fracturing processes (i.e. Mizutani et al. 1976; Aydan and Daido 2002; Aydan et al. 2003, 2011). These may be used for the real-time assessment of the stability of rock structures. An application of this approach was done to the Taru-toge tunnel a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan (Imazu et al. 2015). The parameters measured involve electric potential variations, acoustic emissions, rock temperature, temperature and humidity of the tunnel in addition to the measurements of convergence and loads on support members during the face advance."

Jan 1, 2016

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016

By R. L. Pozzo

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying the Faraday's Law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a nonmagnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-electrode system involving pyrrhotite, pyrite and grinding media was also investigated as a first step towards elucidating the nature of interactions that occur in the grinding of complex sulfide ores.

Jan 1, 1987

By R. Schipper

Two bench scale biochemical reactors (BCRs) were operated over a period of 3 months for the removal of uranium, radium, and selenium from mining influenced water (MIW). A BCR is an anaerobic reactor comprised of organic and inorganic substrate including woodchips, straw, sawdust, and limestone. Uranium and selenium are removed in a BCR by biological reduction of oxidized species (i.e., selenite, selenate) to less soluble forms (Pahler et al. 2007, Blumenstein et al. 2008, Rutkowski et al. 2013). It is believed that radium may be removed through absorption to the biomass in the BCR. The bench scale BCRs were constructed of 6 inch PVC columns with a top to bottom flow configuration. The bench influent water consisted of three different water ratios from two adit seeps. BCR hydraulic retention times of 24 to 36 hours were targeted during the study. Influent concentrations ranged from 19 ug/L to 1.86 mg/L for dissolved uranium, 12 ug/L to 270 ug/L for dissolved selenium, and 4.9 pCi/L to 24 pCi/L for radium 226. The average and maximum dissolved uranium removal was 93.6% and 98.5% respectively, the average and maximum dissolved selenium removal was 93.3% and 98.9% respectively, and the average and maximum radium 226 removal was 89.5% and 100% respectively.

Feb 23, 2014

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By M. Sears, G. S. Esterhuizen, Z. Khademian

According to the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in U.S. longwall mines were caused by roof instability. Gateroads are subject to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many U.S. longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the Bonded Block Method (BBM) modeling of roof by UDEC was validated against field extensometer measurements in a longwall gateroad entry roof at a 180-m depth of cover. The BBM was shown as capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. These types of studies are difficult and costly to conduct in an operating mine. Results show how the contribution of bolts, straps, and cable bolts can be quantified using the BBM models. The study demonstrates the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 1, 2023

By J. Brune

The need for reliable and adaptable underground mine communications has become a focal point for both the safety and logistics of a mining operation. New mine communication technology aims to connect personnel, equipment, and data together while setting up a network that can be utilized during normal operations and also in an emergency event. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) requires mine operators to establish post-accident, two-way communication between underground and surface personnel and electronic tracking for all mine personnel. Communications systems must be designed such that they can survive major mine accidents, including explosions, fires, inundations and ground falls. Typical, wire-bound communication technologies are vulnerable because wires are often destroyed in such accidents. Wireless technologies that work well on the surface, such as cellular telephone networks; have limited applicability underground because the wireless signals do not propagate through rock.

Feb 23, 2014

By R. Schlüter

"The “Biohydrometallurgical Center for Strategic Elements (BHMZ)” is a cooperation of 13 departments of the Technical University Bergakademie Freiberg fostering interdisciplinary research along the whole (bio-) hydrometallurgical process chain to extract indium and germanium from sulphide ores. Research comprises methods to (i) bring the respective metal from the source material into aqueous solution and (ii) different approaches to extract pure metal or metal-containing materials from the solution. Within the BHMZ the Department of Underground Mining Methods deals with the design and implementation of an underground testing facility for bacterial in-situ stope leaching in its own “Research and Educational Mine”. The intention is to investigate innovative approaches for leaching technologies by crack initiation due to hydraulic fracturing or water pressure blasting under consideration of leaching kinetics and underground conditions. It is planned to set up two testing units comparing energy input and the metal output of conventional (blasting) as well as one of the innovative technologies. Aim of subproject is to establish an innovative and sustainable method ready for up-scaling. BACKGROUND Metals like copper and zinc mainly occur as sulphide ores in nature. Due to the insolubility of these sulphide minerals the respective metal is commonly extracted by pyrometallurgical processing methods. These methods require several steps of enrichment of concentrates such as flotation and roasting (Figure 1) under extensive energy utilization. Additionally, this arouses the emission of sulphur dioxide gas which can have a negative impact on the environment in form of acid rain, as long it is not caught by sulphuric acid facilities (Schippers et al. 2011). However, to treat the ore on the surface either open pit or underground mining operations are necessary. This implies operation steps from excavating, loading, and conveying/hauling, to dumping with the sub-processes crushing and stashing. Due to the tendency of increasing depth, more complex ores and decreasing ore grades of the mineable deposits as well as increasing energy and environmental costs these conventional mining and processing methods become in general more costly and difficult to apply. Hence, hydrometallurgical processes and especially the suitability of bioleaching as an alternative in-situ method for future mining projects should be examined. Leaching by means of microorganisms is a combination of mining and processing by converting the insoluble metal into an aqueous form. This technology is an economically beneficial and environmentally friendly alternative to pyrometallurgical processing methods especially for primary and secondary low grade ores. Mainly the extraction of copper but also of zinc and lead from sulphide ores is state-of-the-art in surface leaching operations like heap and dump leaching (Figure 1)."

Jan 1, 2015

By Raimo Matikainen, Pekka Särkkä

HISTORY The history of mining in the Outokumpu Co. shows continuous development of small and medium-sized mines, coupled with a permanent improvement in min¬ing methods and mechanization. Tables 1 and 2 provide a brief outline of the major events over the years of operation. Some of the mines have had relatively short lives as in the case of Nivala, Korsnas, Kylmäkoski, the surface pits of the Kotalahti, Vuonos, and Hammaslahti mines, and some very small pits. The sequence in which the mines started opera¬tions is shown in Table 1 and production increases in Table 2. GEOLOGICAL FRAMEWORK Most of the ore deposits in Finland (see Fig. 1) are situated in middle Precambrian (1500 to 2300 m.y.) formations corresponding to the Baltic shield. The ores and country rocks are generally firm, with a minimum compressive strength of 60 MPa (8700 psi). The sulfide ores, of importance to the national econ¬omy, can be divided into copper-nickel deposits, asso¬ciated with basic and ultrabasic rocks (1900 m.y.), and the sulfide ores found in well-preserved Svecokarelidic crystalline schists (1800 to 2300 m.y.) which contain varying amounts of copper, zinc, cobalt, nickel, and lead. Over 90% of the sulfide ore mined to date in Fin¬land and existing in the known ore reserves belongs to deposits situated in the main sulfide ore belt. This belt extends diagonally across the country over a breadth of Table 1. Sequence in Which Mines Began Operations 1913 Mining started at the Outokumpu mine (now called Keretti) 1928 Large scale systematic exploitation started in the Outokumpu mine Opening of mines: 1942 Nivala mine (1942-54) 1943 Yiojärvi mine (1943-66) 1947 Orijärvi mine (1947-54) (Mining started in 1757) 1948 Aijala mine (1949-58) 1952 Metsämonttu mine (1952-58 and 1964-74) 1954 Keretti's new mine plant 1954 Vihanti mine 1959 Kotalahti mine 1961 Korsnäs mine (1961-1972) 1962 Pyhäsalmi mine 1966 Virtasalmi mine 1967 Kemi mine 1970 Hitura mine 1971 Kylmäkoski mine (1971-74) 1972 Vuonos mine 1973 Hammaslahti mine 1978 Vammala mine Table 2. Ore Production of the Outokumpu Oy Mines Year 1000 t of Ore 1913-1928 252 1929-1954 13 075 1955 1 105 1960 1 784 1965 2 627 1970 3 269 1975 5 825 1976 5445 1977 4 939 1978 5 766 1979 5905 40 to 150 km, from Lake Ladoga to the coast of the Gulf of Bothnia. The main sulfide ore belt includes the Outokumpu copper-zinc, the Kotalahti nickel-copper, the Pyhäsalmi copper-zinc, and the Vihanti zinc ore zones. The Outokumpu ore district occurs in a mica schist area about 60 x 100 km, in association with belts of metamorphic Svecokarelidic quartzites, black schists, dolomites, skarn rocks, and serpentinites. The main ore minerals are chalcopyrite, pyrrhotite, pyrite, and sphalerite. In addition there are nickel and cobalt minerals such as cubanite and cobalt-pentlandite, which have been of economic importance. In this area, Outokumpu Oy exploits the deposits at Keretti and Vuonos. The latter was discovered as an extension of the Keretti ore field about 6 km to the northeast. The Kotalahti geological formation extends across nearly 400 km. The host rock of these mostly pipelike deposits is generally serpentinite, pyroxenite, or norite. The main ore minerals are pyrrhotite, pentlandite, and chalcopyrite. In this zone, the deposits of Kotalahti, Hitura, and Virtasalmi are at present under exploitation by Outokumpu Oy. The Vihanti geological formation is located in west¬ern Finland and is about 40 km wide and some 200 km long. The rock associations are crystalline schists including dolomites, mica schists, mica gneisses, gray¬wacke, and acidic or basic volcanic rocks, which change generally, in connection with the mineralization, into skarn and cordierite-anthophyllite rocks. The host rocks are dolomite, skarn, graywacke, and quartzitic rock and the principal minerals are sphalerite, chalcopyrite, galena, pyrite, and pyrrhotite. The accessory minerals are mainly cubanite, arsenopyrite, molybdenite, and native gold and silver. The two largest ore bodies being exploited at pres¬ent by Outokumpu Oy are the Vihanti mine, which pro¬duces zinc, lead, and copper, and Pyhäsalmi, which con¬tains copper and zinc. Deviating from the sulfide ore types described earlier is the Hammaslahti copper ore located in the southeast-

Jan 1, 1982