Search Documents

By Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muffling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the rod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

By Henry W. Busch

Determination of the aldehyde content of Diesel-engine exhaust gas has proved rather cumbersome and unsatisfactory when carried out in its entirety in field investigations; therefore, studies were conducted with a view to developing methods by which samples might be collected in the field and trans-ported to the laboratory for analysis. Experience also indicated that aldehyde samples collected in water solution and then transported to the laboratory sometimes underwent serious changes in composition if several days elapsed between sampling and analysis. Polymerization of the aldehydes, which takes place readily in dilute aqueous solutions, may have been the cause of such changes. Because of these difficulties, experiments were conducted to find a suitable stabilizer or preservative for dilute aqueous solutions of the aldehydes that occur in Diesel-engine exhaust gas, so that in field studies a known volume of gaseous sample might be collected and brought into contact with water, and the resulting solution of aldehydes analyzed in the laboratory at some later time with reasonable certainty that the results would represent the composition of the original sample,

Jan 1, 1949

By John S. Berber

Tar produced as a byproduct from low-temperature carbonization of coal contains only small amounts of valuable lower boiling tar acids but relatively high percentages of high-boiling tar acids. These high-boiling tar acids are characterized by a high degree of alkylation and can be converted into the lower boiling homologs by catalytic treatment to remove the alkyl groups or decrease their chain lengths.

Jan 1, 1965

By Douglas C. Peters, Valois R. Shea-Albin, Dennis R. Dolinar

An accurate assessment of the vertical stress on a coal seam at depth is important for mine design. Vertical stress calculation techniques presently available either are not sufficiently accurate or cannot handle complex surface topography. Therefore, the U.S. Bureau of Mines developed a computerized method to calculate vertical stress exerted on surfaces at depth that includes the effect of topography. Two input data sets are required: a digital elevation model containing topographic elevations and a coal seam file defining coal seam elevations at depth. Boussinesq's equation then quantifies the vertical stress resulting from topography. The computerized method was tested on a coal seam overlain by a complex topography where a vertical stress map encompassing several square miles was produced. Results show that depth mitigates the affects of surface topography, while the coal seam topography has a direct effect on the vertical stress. In comparison to the computerized method, the direct stress method overestimates stress under hills and underestimates stress under valleys. The largest difference between the two methods occurs under the steepest topographic relief. A limitation of the computerized method is that stresses cannot be accurately determined near an outcrop.

Jan 1, 1992

By Clarence O. Babcock

This Bureau of Mines report presents the initial development of a two-dimensional method of analysis for inclusions in plates in which the deformed shape of an open hole and the separate structural behavior of inclusion and plate with hole are used to obtain the stresses and strains in the inclusion only. In this report the solution for a circular inclusion is presented because a direct verification of the results with previous solutions was possible. The numerical results were in exact agreement with those obtained with the equations of Sezawa and Donnell. The equations developed are less complex than those of Sezawa and more general, for a circular inclusion, than those of Donnell. Stresses and strains in the inclusion are in terms of the elastic constants of the inclusion and the plate and the biaxial stress field applied far away. The elastic constants can be all different. An important conclusion from this work is that a difference in Poisson's ratios between inclusion and plate may be as important as a difference in Young's moduli between inclusion and plate in producing the inclusion effect. Many problems in mining and rock mechanics can be treated as inclusion problems. The understanding of inclusion behavior on a physical basis should provide the solutions to some of these problems.

Jan 1, 1974

By A. A. Afshari, D. G. Frazer, C. F. Stanley

"INTRODUCTIONThe primary function of the lung, i.e. gas exchange, occurs in peripheral units termed alveoli• Diagnosis of lung dysfunction ls therefore dependent on techniques to evaluate the status of the peripheral airways. Since these airways and alveoli are very small, it is difficult to determine directly how they function or how the function is changing due to disease. Yet this unde1·standing is critical to the design of instrumentation to detect early changes in lung function due to disease.An interesting hypothesis describing one aspect of small airway function has been proposed by Frazer (1) as gas trapping due to the formation of menisci in the airways. An additional study (2) proposes that the breaking and possibly the formation of these menisci could generate lung sounds, i.e. crackles. These lung sounds were recorded by placing a microphone at the trachea of an excised rat lung. The lung was degassed and then inflated and deflated. At points along the path of inflation, lung sounds were recorded. However, determination of the origin of the sounds was not attempted due to the difficulties induced by contacting the lung st1rface with a microphone.The purpose of this paper is to describe a non-contacting, whole field technique to monitor and describe the movements of the lung surface during inflation - deflation cycles.HOLOGRAPHIC INTERFEROMETRYHolographic interferometry is a full field, non-contacting and non-destructive technique that measures deformations of an object with a sensitivity in the order of the wavelength of light. A laser beam is split, with one beam reflected from an object and the other used as a reference beam. Both beams combine to produce a hologram of the object on a photographic plate. The process utilizes the concepts of interference, i.e. the two wave amplitudes will add at the points where the difference in optical path lengths over the exposure period is zero or a whole number of wavelengths and will subtract at other points."

Jan 1, 1989

By H. E. Powell

The selective recovery of nickel and zinc from a waste phosphate solution by solvent extraction was investigated by the Bureau of Mines as part of a broad program to recover valuable metals and compounds from industrial wastes, and to reduce the associated land and water pollution caused by dumping these wastes. The waste, which resulted from the phosphation of automboile bodies, yielded 99 percent of both the nickel and the zinc by extraction with dinonyl naphthalene sulfonic acid (DNSA) and di-2-ethylhexyl phosphoric acid (EHPA), respectively. Dilute sulfuric acid was used to recover the metals and regenerate the solvents.

Jan 1, 1970

By G. W. Reimers

Metastable pyrophoric wüstite (FexO, with x between 0.89 and 0.95) was found to be much easier to grind to colloidal state than were its stable disproportion products magnetite or iron. The grinding of polycrystalline magnetite appears to be complicated by the magnetic flocculation arising from interparticle attraction. This is superimposed on the attraction of a fluctuating electric dipole for a neighboring induced dipole. More than 85 pct of the tumbling time was saved by grinding antiferromagnetic wüstite instead of the ferrimagnetic oxide of iron (Fe304). Disproportionation of colloidal wüstite to the stable ferromagnetic and ferrimagnetic colloidal particles of alpha-iron and magnetite, respectively, was accomplished rapidly at temperatures above 250° C but below 570° C, the eutectoidal stability point of the wüstite phase.

Jan 1, 1972

By F. E. Armstrong

The Bureau of Mines has conducted a research program to systematize the art of locating uncharted and lost oil and gas wells that penetrate coal seams; this publication presents a preliminary summary of its findings. Although no method or combination of methods will guarantee finding all uncharted and abandoned wells in a particular area, at least 75 percent of such wells can be located by compiling and applying all available information and using modern metal detectors.

Jan 1, 1973

By Lloyd A. Morley, Robert Stefanko

1 Abaibanel, S , "Deflection of Confining Walls by Explosive Loads," Israel Jour. Technology, vol. 4, n. 1, Feb 1966. 2 Albertoni, S and others, "Numerical Computation Methods for Implosion Processes," EURATOM Proc. of the Conf. on Megagauss Magnetic Field Generation by Explosives and Related Experiments, Milan (Italy), July, 1966. 3 Alexander, S. J , and Hambly, E. C., "Design of Structures to Withstand Gaseous Explosions," Concrete, vol. 4, n 2, Feb. and March, 1970. 4 Anonymous (Belgium Institute of Extractive Industries), "Report for 1968 (covering approved equipment for Belgiums gassy coal mines)," (in French and Flemish), Amales des Mines de Belgigue, n. 6, June, 1969. 5. Anonymous (Ghent Univ., Belgium), "The Welding of Very Thick Steels. Margin of Uncertainty of the Robertson Test," EURATOM Contract 042-61-9-RDB, May 20, 1965. 6. Anonymous, "Inportance of the Nature and Size of Weld Defects with Regard to the Mechanical Strength of Pressure Vessels, (in Flemish), A. Sys. Rev. Soudure, vol. 27, n. 3, 1971. 7. Anonymous (Raentgen Technische Dienst N V., Rotterdam), "Non¬Destructive Welding," Quarterly Report No 13, EURAEC - 1342, March 30, 1965. 8. Anonymous (Staff, USBM Safety Research Center), "Research and Technologic Work on Explosives, Explosions, and Flames: Fiscal year 1969," USBM IC8492, 1970. 9. Anonymous, "Symposium on Flameproofing Intrinsic Safety and Other Safeguards in Electrical Instrument Practice, April 27, 1962," IEEE Conf. Report Ser. 3, 1963. 10. Anonymous, "Unfired Pressure Vessels," ASME Pressure Vessel Code, Sec. 8, 1965. 11. Anonymous, "Unusual Pressure Relief Devices," Industrial and Engineering Chemistry, vol 54, n. 1, Jan., 1962. 12. Archer, G. L., "Design to Avoid Brittle Fracture in Welded Structures," Paper No. 4, Improving Welded Prod Design, vol. 1, Welding Inst., Cambridge, England, 1971. 13. Bailey, F. C., "Buckling and Failure Strength of Plating Panels Loaded in Shear," Final Report NASA Contract NObs-72290, Lessels and Assoc., Inc., Waltham, Mass., Sept. 20, 1963.

Jan 1, 1974

Synthetic dawsonite [NaAl(OH)2C03] has been prepared with crystallinity similar to that of dawsonite found in oil shale deposits of the Piceance Creek area of Colorado. Optimum experimental conditions were as follows: Na/Al atomic ratio, 43; temperature, 175° to 200° C; pCO2, 15 psig; and reaction time 5 hr. Chemical and spectrographic analysis revealed that the synthetic dawsonite was of high purity and Has essentially stoichwmetric. Similarity of the synthetic to natural dawsonite, demonstrated by X-ray diffraction, infrared spectrophotometry, and electron microscopy, suggests its suitability as a standard.

Jan 1, 1972

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By R. V. Ramani, K. V. K. Prasad

"Solution of most engineering problems requires, in addition to vast ·numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity; However; it is only .recently that approaches like the expert systems methodology have been developed to ·incorporate the Judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or ""shells"" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development or a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.INRODUCTIONExpert systems (ES) are interactive computer programs which use high quality specialized knowledge in some narrow problem domain to solve complex problems in that domain. These complex problems lack structured and/or standard ways of solution and involve substantial use of subjective and experience based knowledge. One of the first expert systems was MYCIN, developed in 1974, in which subjective and heuristic knowledge of expert physicians was used to diagnose infectious diseases and provide antimicrobial therapy (Buchanan arid Shortliffe, 1984). Since MYCIN, expert systems applications have appeared in other areas such as mineral prospecting (Gaschnig, 1982), configuration of computers (McDermott, 1982) and structural engineering (Bennett and Englemore, 1979)."

Jan 1, 1989

By Robert L. Marovelli

The thermal conductivities of six rocks were measured by the transient line source method over the temperature range of -850 to 1,500° F. Close-fitting ceramic probes were used in 0.065-inch-diameter holes drilled through 5-to 6-inch-thick rock specimens. Taconite, granite, quartzite, and basalt were used in the tests. The method yields absolute data and is applicable to both laboratory and in situ measurements.

Jan 1, 1965

By D. S. DeLong, A. Giza, D. G. Fraser, V. A. Robinson, T. B. Whitmoyer, J. E. Sneckenberger

"A cotton dust animal exposure system has been modified to incorporate a microcomputer feedback loop to monitor particle concentrations. The loop's major components are a minature real-time aerosol monitor (miniram) to estimate concentrations and a microcomputer to read the miniram's data and to control a stepper motor that adjusts the amount of dilutant air mixing with respirable cotton dust. Ninety minute trials of this system indicate that the standard deviation of particle concentrations is within 0.68 Mg/m3 of the average concentration, insuring a near constant concentration of respirable dust throughout the exposure.INTRODUCTION Previous workWeyel et al. (1984) have determined that respirable cotton dust can be shaken from bulk cotton samples using acoustical energy. The particle generator designed to utilize this fact operates like a commercially available sonic sifter, but on a much larger scale.While this generator successfully resuspended trapped respirable cotton dust, the generator output concentration decreased exponentially with time. This disadvantage was solved by Frazer et al. (1986) by operating the generator with a sinusoidal voltage near the minimum resonance frequency of the generator. This adjustment enabled the generator to produce respirable cotton dust for six hours or longer.Frazer et al. (1987) utilized the modified acoustical generator to produce a cotton dust animal exposure system. The cotton dust concentrations were estimated by a miniram, a light scattering aerosol Monitor. The system operator used the miniram values to adjust the system's parameters to maintain the desired concentration level.PurposeThe objective of this study was to introduce a computerized feedback loop to the operator controlled cotton dust animal exposure system. The miniram's estimates were analyzed by a microcomputer to determine what adjustments in the flow of dilutant air were necessary to maintain the desired cotton dust concentration. These modifications were intended to improve system performance and ease the system operator's work burden."

Jan 1, 1988

By A. W. Ambrose

"Those having an intimate knowledge of the relation between production and consumption of crude oil in the United States have realized for some time that production will not be able to keep pace with consumption. The American public has had this called forcibly to its attention by the increased prices of gasoline and crude oil, and by the recent shortage of gasoline on the Pacific Coast. In substance, each year we are consuming millions of barrels of oil more than we produce, and this deficit must be made to by importations. A careful analysis of the situation makes it evident that we need every barrel of oil that can be produced.Need for the Petroleum Production Engineer.Under present production practices perhaps 80% of the oil still remains in the sand. (See Lewis, J.O., Methods for increasing the recovery from oil sands, U. S. Bureau of Mines, Bulletin 148 p. 8.) Many wells are making water, and even whole pools are being flooded. The burning of fuels under field boilers is not generally efficient, and often gas is not made to do its full duty in bringing the oil to the well.In the past the producer has had to combat these and other problems single-handed. He has been too busy to give them special attention, and he has had little competent engineering advice. Oil, gas, and water occur underground according to certain natural laws. Undoubtedly an engineer, who is familiar with production practices and understands the fundamentals of the accumulation of oil and gas, can be of service to the producer by specializing on certain problems with a view of getting mare oil from the sand. In every other enterprise of similar magnitude the engineer is regarded as a necessary unit to its operation, and he should be so in the production of oil. His field of work should extend to every phase of production in which science and engineering and geology"

Sep 1, 1920

By George C. Price

The Bureau of Mines conducted this study in the Roslyn No.5 coalbed in the State of Washington to determine the feasibility of mining hydraulically the portion of the coalbed that was steeply pitching. All of the experimental mining was done while advancing raises and rooms. A Bureau-developed hydraulic mining machine was used successfully in the pitching coalbed. It consisted of a remotely controlled monitor mounted on a self-advancing roof support unit of the type commonly used for roof support in longwall mining systems. The coal cutting rates averaged 0.73 and 0.54 ton per minute in raise and room mining, respectively, while using water volumes up to 230 gpm at a pressure of 4,000 psig. Productivity averaged 4.7 and 5.2 tons per man-shift for raise and room mining, respectively, compared with 7.5 and 8.5 tons per man-shift, respectively, by conventional hand mining methods.

Jan 1, 1965

By Frank E. Cash

Large quantities of explosives are consumed in the underground mining of ores in the Lake Superior district. Because of the recognized danger of accidentally releasing the potential highly destructive forces contained, the safes possible procedure in the transportation, storage, and use of explosives is necessary. Underground magazines recently constructed in the district give evidence of the earnest desire of the mine operators to incorporate all possible safe-guards in the storage of explosives, including a careful choice of location and arrangement in the plan of the magazine.

Jan 1, 1946

By Gerald T. Homce

A system capable of monitoring a mine electrical power system to detect incipient electrical component failure could significantly improve power system safety and availability. The U.S. Bureau of Mines funded a contract with The Pennsylvania State University (Penn State) to establish the theoretical and technical framework for such a system. This report briefly outlines the contract, reviewing related Bureau and Penn State work prior to its award, and describes support work carried out by the Bureau. The main focus of the report is on research efforts by Penn State and subsequent results. An existing algorithm for incipient-failure detection and classification was studied, and recommendations are made to improve its performance. In addition, mathematical models of cable-connected motor systems and deteriorating motors were developed and implemented on computers. These models and laboratory tests were used to study and document relationships between component deterioration and electrical terminal effects. The project was supported by the U.S. Navy and the nature of its interest in the application of failure prediction techniques is also included.

Jan 1, 1989

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"This report is () expansive test program by the Bureau of Mines to determine methods from various and ferrous manganese-grade product () widespread () and manfniferrous iron ores. Among the samples received for testing was one from the pits of the Barytes Mining Co., 1-1/ 2 miles northeast of Cartersville, Ga.. The property is approximately in the center of the Cartersville manganese district and shares a common corner with properties of the New Riverside Ochre Co. and the Etowah Development Co., both producers of manganifereus ores. The deposit is typical of the district and occurs in residual clays resulting from weathering of the Shady limestone and Weisner quartzite. 7/The property is developed by a number of open pits ranging to 60 feet in depth. In 1918 several carloads of manganiferous iron ore was mined from an alit on the property. Since then mining operations have been negligible. The ore is known locally as calico ore.A 4-ton sample representing -re as it occurs in the -pen pits vas furnished for testing. The sample consisted of a mixture of red iron oxides, wad, and clay, with small pebbles of manganese oxides and siliceous fragments scattered throughout."

Mar 1, 1943