Search Documents

By D T. Froedge

This paper is a presentation of a coyote shot at the Oriskany Sand Quarry of the Pennsylvania Glass Sand Corporation, Berkeley Springs, West Virginia.

Jan 1, 1982

By Ed O'Connor, Per-Anders Persson, Manhong Zhou

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1997

Almost one half of Canada's total land surface is underlain by permafrost. This term describes the thermal condition of earth materials when their temperature remains below 0°C continuously for a number of years. The drilling and blasting of frozen materials requires more energy than the blasting of same in its unfrozen state. The cost of comminution could double in permafrost even with adequate organization, drilling equipment and proper explosives.

Jan 1, 1975

By Stewart A. Silling, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

GEM (Geologic Element Motion) is a Distinct Element Method (DEM) for modeling blast-induced heave. It was developed with a very fast computational algorithm that efficiently treats many different element shapes utilizing alternating arcs and lines to create GEM elements. The GEM computational technique has been previously documented so only a summary will be included in this paper. New features of GEM are the ability to define the size of the rounded corner radius as well the length of the sides for quadrilateral and hexahedral elements. Circles can be created from a quadrilateral element with zero length sides and four arcs. An additional new GEM feature is energy partitioning between brisance and heave. This physics-based partitioning is essential for accurate modeling of blast results over a wide range of rock and explosive types. It accurately defines the volumetric, pressure and energy state of the explosive gases in a blasthole following detonation. Rock mechanical properties and explosive characteristics are included in the calculations. Example simulations provide comparison of the GEM predicted heave for two different classes of explosive. A GEM simulation utilizing hexahedral elements is compared with previous modeling incorporating circular elements.

Feb 6, 2023

By Ann Barron, Paul Downing

Those employed in the explosives industry must have a keen familiarity of the explosives products they handle, the safety pro c e d u res they must follow, and the increasing number of laws and regulations governing blasting operations in order to perform their duties satisfactorily. For this reason, companies must make certain that their employees have the necessary knowledge and full understanding of their blasting and non-blasting responsibilities. Consequently, training is one of the most important elements in any company’s safety program.

Jan 1, 2004

By Jerry W. Schweiker

An extensive computer program has been developed which will store and analyze pertinent blast related parameters such as date, time, shot coordinates, charge, delay times, etc. In conjunction with these blast parameters, measured ground vibration information can be stored. In addition to actual seismograph data, predicted ground vibration in terms of velocity (inches/sec) can be generated for selected receiver locations. The magnitude of the blast generated ground vibration is based on scale distance relationships. The program can be used for planning blasts, to satisfy local environmental regulations and for insurance and/or legal purposes.

Jan 1, 1984

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Evan Jannoulakis, Wilfrid Comeau

Using the Scaled Distance (SD) and the vector sum Peak Particle Velocity (PPVvs) from a single delay, preferably single blasthole, in a shot, a number is derived which has shown itself to be consistently related to blasting efficiency, as experienced by one of the authors of this paper over the last thirty years. The numbers derived by this process range in value over one order of magnitude more or less. This variation, a function of distance, weight of explosive in the delay, blasthole diameter, blast design, powder factor and the geological environment, can be consistently related to two of these factors, powder factor and distance. In actual use the measured "BED" representing good blasting results should not vary by more than + 33 to + 50 percent of the estimated "BED" in non calibrated cases, and + 10 to 20 percent where previous experience is available. Relatively high "BED" values are indicative of poor blasting results while relatively low "BED" values may be precursors of poor blasting results in a shot. There are many variables in the geological environment which can affect the "BED". A case study is presented from a surface coal mining operation in eastern Canada. This case study tries to evaluate the reasons for the variability in "BED" values derived from multi-hole shots. A problem in using "Signature Vibrations" from a single-hole shot to predict blasting vibrations from multiple-hole production shots is identified.

Jan 1, 1998

By J Lyall Workman, Peter N. Calder

"Presplitting is a technique mines and quarries may use to produce high quality final pitwalls. Damage from backbreak can be minimized, thereby insuring the final pit walls standat the designed angle. Thus costly excess waste removal is avoided. Safety in the pit isenhanced. Control blasting is an essential component of procedures to maintain the stabilityof final pit walls prone to failure."

Jan 1, 1993

By Javier Illanes Pizarro, Gustavo Huerta Valer, Jorge Cárdenas Miranda

Bench stability is the basis of sustainability in an open pit mining operation. Taking care of the pit walls while maintaining fragmentation results can prove a challenge. In this study, technical proposals have been developed for extra hard rock mass (UCS>175MPa) with presence of unfavorable structural planes in high copper grade zones. The base case shows low compliance of fragmentation results and a significant loss in berm width, with over size boulders causing low primary crushing rates. Paradigms in current drill and blast design were overcome to improve fragmentation results and achieve objectives.

Feb 6, 2023

By B Kniivila, A B. Andrews, T Lerick, Keith Jansen

Minntac Mine is a large, open pit taconite mine located at the center of the Mesabi Iron Range in northern Minnesota. The planned development of the Mine in the direction of nearby communities prompted a comprehensive study of off-site blast effects that resulted in numerous refinements in blasting practices.

Jan 1, 1984

By Luan Monteiro, Francisco Biulchi

The AngloGold Ashanti - Cuiaba mine sought innovative approaches to minimize lateral development and stope extraction time while maintaining optimal gold recovery and minimizing dilution. The stope 8GAL EXT 30 was selected as a case study. Traditionally, conventional blasting methods in such a scenario would necessitate either a single mass blast or slot development at each end of the stope. These methods typically compromise recovery and dilution or increase development time and risk. Additionally, conventional wired detonators require workers to re-enter the stope between blasts to load blastholes and connect detonators. The wireless initiation system offers a solution by initiating blastholes using magnetic induction signals that can penetrate rock, air, and water. This technology allows a pre-charged stope to be mined without requiring workers to re-enter the area between blasts to charge and connect blastholes. Engineers from Orica and AngloGold Ashanti designed a new extraction sequence utilizing the wireless initiation system. The process began with the opening of one end of the stope using a conventional slot and wired electronic detonators. Subsequently, pre-loaded rings were fired in three blasts to extract the opposite end and the intersection. The 8GAL EXT 30 stope was successfully mined using this technology enabled method. Each blast was meticulously monitored, and the stope void was scanned to assess blast performance. The results demonstrated a 4.6% improvement in recovery and a 16% reduction in dilution compared to the initial plan, and reduced exposure of people to hazardous locations in the stope. These results represent an additional value of USD 200k, gained from implementing wireless initiation to enable this particular blasting schedule.

Jan 21, 2025

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling.

Feb 1, 2020

By K. Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics (hereafter “the company”) developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits

Jan 1, 2024

By Michael Burrell

This project involved the protection of an historic landfill located on the site. Construction blasting was for a permanent access road to carry traffic to and from a new metal processing plant being constructed nearby. The landfill contained materials disposed of during the closure of a Phosphorus plant that had previously occupied a portion of this site.

Jan 1, 2012

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

By U. Steiner

Electronic detonators have been in commercial use for a decade, with an excellent safety record. This paper lists known incidents involving electronic detonators. Typical standards required by regulatory bodies for static electricity and electromagnetic fields are reviewed. The performance of some detonators is compared to these standards; in general the minimum standards are easily exceeded. The general resistance of electronic detonators to extraneous electrical energy that can be derived from the body of test results is compared to danger levels for exposure of humans to these energies; it is shown that electronic detonators can safely tolerate higher electrical energies than people can. This comparison includes comparable data for electric detonators, which are shown to be more vulnerable to extraneous electrical energy than people are. Electronic detonators also bring significant safety benefits in blasting due to their testability, two-way communications, reliability, programmability and precision. The links between these attributes and enhanced safety are discussed with examples from actual blasting. Although electronic detonators are usually more vulnerable to extraneous electricity than non-electric initiation systems, the paper shows that the net safety benefit in handling and blasting is in favor of electronic detonators, which are the safest initiation system that has ever been offered to the mining industry.

Jan 1, 2010

By Tacio Ferreira

How state-of-the-art software, data analysis and communication applied to drilling and blasting techniques have have allowed quarries in the Midwest of the United States to improve results downstream

Feb 1, 2020

By Hideaki Kitajima, Daisuke Fukuda, Kazuma Moriya, Katsuya Sasaki, Katsuhiko Kaneko

The purpose of this research is to analyze the fracture process and achieve design optimization of a splitting method for concrete and rocks termed the electric discharge impulse crushing method (EDICM). The EDICM utilizes the cartridges being set in boreholes in the splitting target. The cartridge has a thin metal wire and is filled with nitromethane. By applying the electric discharge to the wire in the cartridge, plasma is caused leading to the vaporization of the wire. Then the deflagration of the nitromethane commences, which generates borehole pressure for splitting the target. Although the required splitting time is roughly several hundred micro-seconds and much slower than ordinary blasting, the fracturing still completes in quite short time and understanding the fracture process of opaque and brittle materials such as rock and concrete in this time scale is of academic importance.

Jan 1, 2011

By Carlos Enrique Arroyo Ortiz, Jadir Pedro Alves

This paper presents some of the results obtained during the research work about the use of technologies and digital transformation in the process of rock drilling in open pit mines. The use of automation presents itself as a disruptive factor and a driver of improvements that provide sustainability in rock drilling. Seven main operational parameters were utilized to combine measurement while the drilling (MWD) with other information generated by the equipment during hole drilling, in six different lithologies in an iron mine, located in the central region of Minas Gerais in Brazil. Adjustments and corrections were made to the data collected in order to minimize external influences other than the rock itself, to ensure the effectiveness of the analyses. Finally, we sought to compare the performance of the drilling process in manual and automatic operation modes. Thus, making it possible to show the efficiency and impact on the sustainability of rock drilling operations in open pit mines.

Feb 6, 2023