Search Documents

The Mineral Resources Act 1989 was assented to on 25th October, 1989 after more than two years of consultation and negotiation between Government, the mining industry and other affected parties particularly the major rural organisations.The legislation proposes major conceptual changes in a number of areas and adopts a totally new approach to the definition of land and the mechanisms available to the mining industry for accessing such land.Unfortunately the passage of the legislation through Parliament coincided with the lead-up to the State election. Ultimately it became an election issue generating much adverse comment in the media particularly from rural and landholder groups. It was obvious that much of this anti-mining propaganda resulted from a lack of understanding of the legislation and the benefits that flow to the majority of landholders as well as the mining industry.It is essential that the contents of the Mineral Resources Act be thoroughly understood by all parties. Only then will all the State's resources be able to be developed in a multiple land use environment.This paper outlines the philosophy behind the new Act and the more important provisions contained therein.

Jan 1, 1990

By Jensen B

The approach of using the Coward Triangle for the analysis of flammable mine gas mixtures has been examined for its application, to the flammability of coal dust/gas/air mixtures. Explosible lean limit and rich limit concentration data for dust/methane/air mixtures are examined and illustrated using co-ordinate geometry. It is concluded that a three-dimensional envelope representing hybrid explosible mixtures can be drawn. The dimensions of this explosive zone will vary with the characteristics of the coal dust and the gaseous composition of the mine atmosphere. Further research is needed to establish these dimensions for important mined seams.

Jan 1, 1994

Cyanidation tests by bottle agitation were conducted on an oxidized lead-silver ore containing approximately 12% Pb and 500 g/t Ag. Over 60% of the silver was leached when the ore was ground to 100% passing 0.15mm, whereas 50-60% of the silver was leached when the ore was only ground to 100% passing 0.5mm. Slurry handling and dewatering at the fine grind size were very difficult due to the high clay content of the ore, however this problem was greatly reduced at the coar- ser grind size. The silver recovery at the fine grind size was very dependent on cyanide solution strength with stronger cyanide sol- utions (containing more than 0.1% NaCN) re- sulting in lower solution silver contents. This was thought to be due to the precipi- tation of leached silver by zinc, which was also leached from the ore by the higher cyanide levels. There was a critical zinc level in solution of approximately 1000ppm, above which the silver recovery fell markedly. Cyanide and lime consumptions for this ore were high (typically 5 kg/t and 40 kg/t respectively), hence the processing of this particular ore by cyanide leaching is un- economic at current silver prices.

Jan 1, 1987

By Blair J. R

In the Bayer process, bauxite is leached with caustic soda, forming a solution of sodium aluminate, from which hydrated alumina is precipitated. The efficient operation of the continuous form of this process requires that the concentration of caustic soda be controlled. A computer simulation of the concentration of caustic soda has been conducted to provide information, regarding the dynamic behaviour of caustic concentration, which is not available from normal plant data. The basis of the simulation is a state- space model of an alumina refinery, linearized about the normal operating condition. The formulation of the model, with the relevant approximations and assumptions, is outlined. The simulation of the mudwash section of the. plant is described in detail. A continuous model of the mudwash, having time-varying coefficients, was driven using operating data from an alumina refinery. The modelled response showed reasonable agreement with the recorded plant response.

Jan 1, 1977

The process of establishing the design criteria is the key step in commencing a new project.. The method for establishing design criteria and translating them to a workable plant design is described. INTRODUCTION The use of activated charcoal to recover gold from alkaline cyanide leach liquors is the most rapidly expanding technology in hydrometallurgy today. The process, known as carbon-in-pulp (CIP), has replaced countercurrent decantation as the method for recovering gold by cyanidation. Carbon-in-pulp entails mixing activated charcoal with a ground ore-water slurry containing gold cyanide, allowing the charcoal to adsorb the gold, and then mechanically removing the gold loaded charcoal from the pulp. The pulp is sent to tailing disposal and the loaded charcoal is sent for gold bullion production. Activated charcoal's affinity for gold has been docu- mented for over one hundred years. In the first cyanide plants, one of the preferred methods of stealing gold was to place a piece

Jan 1, 1982

By Stewart C. A

The Northparkes copper-gold project is being developed in Central Western New South Wales approximately 30 km NNW of the town of Parkes and approximately 350 km west of Newcastle. The project is a joint venture between North Limited (80 per cent) and the Sumitomo Group (20 per cent). North is the manager. The basis of the project is three copper-gold orebodies, the northern two of which are being mined by conventional open cut methods with the third and largest orebody at the southern end of the lease to be mined by block caving. A fourth mineralised body has been identified in the centre of the lease. While further evaluation of this deposit is required it would appear to be amenable to block caving. Oxide caps of gold ore and copper-gold ore over-lie the two northern orebodies. Development commenced with the construction of a carbon-in-pulp (CIP) plant to treat the oxide gold ore. Construction of a flotation plant to treat oxide copper-gold ore and sulphide copper-gold ore is underway. When full-scale operation is achieved late in 1996 the plant will treat 5.0 million tonnes of ore per year of which 1.1 million tonnes will be open cut ore and 3.9 million tonnes will be block cave ore. In terms of annual ore tonnage the underground mine will be the largest metalliferous mine in New South Wales and the second largest in Australia.

Jan 1, 1995

By K Biegaj

The paper describes challenges the author has encountered on Australian underground gold and nickel mines over the last eight years, when recovering high-grade gold/nickel bearing mine floor material with a mobile supersucker/giant vacuum cleaner and other equipment. Whilst for a number of years the mine floor vacuuming and other mine floor clean-down technologies have been accepted/adopted and are working well in other parts of the world and on the South Australian opal mines, regrettably, they have not yet gained acceptance of mining executives and mine managers of gold and metal mines in Australia, who still elect to leave the never to be recovered gold/metal behind or to put it plainly - waste it.For reporting purposes during the mining process, the portion of gold/metal included in calculation of ore reserves prior to obtaining capital funds for their development, continues to be camouflaged in various reconciliation and call factors. This approach, ie wasting of capitally developed and already broken ore stocks should be viewed by the shareholders as totally inappropriate to say the least, especially with the current gold and other metals prices.The author attempts to provide answers as to why the technology referred to above has not yet been accepted on Australian gold and metal mines and outlines the way forward.CITATION:Biegaj, K, 2012. Why do shareholders and mining executives allow mine managers to leave behind high-grade broken ore underground?, in Proceedings Narrow Vein Mining 2012 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Gemmell J. B

Zinc-bearing massive sulphide deposits have been mined in Tasmania since 1900. The current major producers are Hellyer and Rosebery, with total resource tonnages (mined plus reserves) of 16 Mt (million tonnes) and 24.8 Mt respectively. These deposits belong to the class of seafloor volcanic-hosted massive sulphides (VHMS) and are located within the Mt Read Volcanics, a narrow belt of continental margin calcalkaline volcanics of Cambrian age. Compared to other Australian VHMS deposits, and world-wide MVT and Sedex deposits, the Tasmanian examples clearly stand-out due to their high metal grades, averaging over 17 per cent Pb+Zn. The deposits vary in morphology from mound style (Hellyer) to sheet style (Rosebery) with other combinations including stacked lenses (Que River) and disrupted cross-cutting bodies (Hercules). All deposits show the classic VHMS zonation from an Fe-Cu-bearing base to a Zn-Pb-Ba-rich top. Zinc, gold and silver tenor commonly increases toward the stratigraphic top of the deposits. The ores have been deformed during regional metamorphism, resulting in folding, shearing and recrystallisation of sulphide lenses. In addition to the major deposits, a number of small massive sulphide prospects occur throughout the volcanic belt and the potential for the discovery of further large, deeply buried deposits remains high.

Jan 1, 1993

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995

By N Fullelove

The Renison Bell Tin Mine on the West Coast of Tasmania has recently installed a new underground ore handling system incorporating underground crushing, conveying and hoisting facilities. Contracts for the sinking of the shaft and the development of the mine were let and managed by the operator, Renison Limited. Hardcastle & Richards was responsible for the design, procurement and construction management of the fixed plant and equipment including civil, structural, mechanical, electrical and instrumentation services. The system demonstrates worldÆs best practice in design and incorporates a state-of-the-art integrated control system allowing the entire system to be controlled by a single operator located in the underground crusher chamber. A rapid construction period was achieved, despite the difficult and constrained underground environment, without affecting the ongoing operations of the mine. The mine, which was established in the mid-1960s, had previously operated by trucking ore to the surface via a decline. Truck haulage distances and costs had increased as the mine became deeper over the years. By the 1990s it had become apparent that, in order to remain economically viable, it was necessary to reduce truck haulage distances and allow the mine to go still deeper to access orebodies such as Rendeep beneath the current workings. The Internal Shaft System achieved this by eliminating approximately 5 km of truck haulage. It allows the production rate to be increased to up to 1 Mtpa compared with a limit of 628 kt per annum by direct truck haulage to surface. The access it provides to the Rendeep ore and other deep orebodies greatly increases the amount of ore which can be economically mined.

Jan 1, 1998

By Turnbull AG

The direct smelting of zinc sulfide con- centrates has been investigated by an extensive series of computer-based thermodynamic equili- brium calculations. The study covers both pure 7.n-S-O-C-N systems and practical concentrate- coal-air-flux systems. It is shown that for a zinc concentrate containing iron and lead sul- tide impurities, a 97% yield of zinc vapour with autogenous operation can be obtained under carefully optimized conditions. The possible integration of this process with existing zinc condensation and recovery processes is Discussed.

Jan 1, 1980

By Heidecker A

Several types of drainage structure providecost-effective environmental controls for water supply to Charters Towers and its mining industry. Drainage groves maintain bank-levee, channel, pool, and spring structures. Failure of drainage structures leads to anoxic fermentation of channel fill releasing residues, such as arsenic, which would otherwise pass harmlesly by fixed on sedimentary particles.Experiments along drainage structures indicate that productive agroforestry could be integrated with expeditious development of groves to cope with environmental change.

Jan 1, 1990

By M Thomas, S Lambert

The Tugun Bypass Tunnel in Gold Coast, Australia was constructed using diaphragm walls with the top-down cut-and-cover method to allow simultaneous construction of an airport runway extension above the tunnel, whilst excavation of the tunnel continued underneath. The tunnel was built in an environment of high groundwater table and deep deposits of alluvial and estuarine soils with the toes of the walls founded in soil deposits. There was a potential risk for differential settlements to occur between the diaphragm wall panels, caused by the runway fill placed over the tunnel roof during excavation. Dewatering within the diaphragm walls was required to facilitate the construction of the tunnel. The tunnel was also built in an area where environmental considerations were of great importance. Three-dimensional numerical modelling was undertaken to predict the differential settlements of the tunnel with considerations of varying subsurface profile, staged excavation and dewatering, non- uniform surface loading and complex soil-structure interaction. Field instrumentation and monitoring was implemented to confirm numerical predictions.  

Jan 1, 2008

By Szpindler G

The results of pot-furnace tests with 35 bituminous coals from 20 seams in New South Wales and Queensland were used to establish the relationship between coal properties, as determined by standard laboratory tests, and the combustion process. The rate of combustion is influenced chiefly by the expansion of the fuel bed, but this cannot be accurately predicted from the crucible swelling number of the coal.The effects of various other factors, such as calorific value and ash yield, were investigated and statistical analysis of the results shows that the coals could be classified satisfactorily according to two experimentally derived parameters, namely heat-release rate at an air flow rate of 260 lb/sq.ft/hr and air flow rate giving stoichiometric combustion. The grouping obtained is shown to be related to ash yield and swelling number.INTRODUCTIQNThe rate of heat release from the fuel bed of a travelling grate stoker and the efficiency with which the heat is used depend upon the design and method of operation of the furnace as well as upon the properties of the fuel. It is difficult to draw general conclusions concerning the influence of fuel properties from tests on a single stoker installation. In the pot-furnace test, on the other hand, a part of the same combustion process as occurs on a travelling grate is carried out in isolation, uninfluenced by furnace design variables, and consequently the effects of coal properties and of the method of pretreatment can readily be demonstrated.While the combustion pot provides a rapid method of assessing the combustion characteristics of a fuel during the ignition and burn-out stages under standard conditions, and of predicting changes in performance with changes in fuel or in air flow rate, it is unable to simulate certain features of furnace design and operation. Data from combustion pot...

Jan 1, 1962

By Onton W

During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impractical and uneconomical to continue deepening it to serve haulage levels below the present No. 5 level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5 level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin. The No. 2 interior ore shaft was only developed below No. 4 level and borehole ropeways with a winder located on the surface were installed in preference to an underground winder installation. No. 2 ore shaft with borehole ropeways commenced lead ore hoisting operations in September 1938. Apart from the copper ore hoisted in the war years of 1943-46, lead ore was hoisted to No. 5 level until September, 1951.

Jan 1, 1988

By M Denton, M Rheinlander, S Mundell, M Broadgate

The manufacturing industry reinvented its approach to the manufacturing process by managing and measuring it end-to-end. This improved returns on production assets, improved information quality and reduced delivery time, resulting in larger net profits through cost reduction and improved cash flow. Today this approach is standard in the manufacturing industry. Resource development has many requirements in common with the manufacturing production line. These include: control of the various steps, transparency of the state of the process to various levels of the organisation and the overall efficiency with which the process is executed. The authors argue that the introduction of manufacturing execution systems (MES) concepts and technologies to resource development processes will lead to similar improvements in control, transparency and efficiency and could improve profitability and enable staff to work more effectively and make better decisions.

Jan 1, 2009

Samples of the feed, underflow and overflow mediums from dense medium cyclones operating at low separation densities in eight commercial coal washeries were sized and analysed, to obtain comparative cyclone classification performance curves for the magnetite, shale and coal components in the circulating medium. The resulting component classification curves indicated that the dense medium cyclones hydraulically classify the magnetite and the shale to the underflow with a Stokesian size and density relationship at these low medium densities, ie the shale curve was shifted parallel to and appropriately coarser than the magnetite curve because of the lower density of the shale. However the lower density coal reverse classified to the overflow (ie away from the cyclone wall) with a similar Stokesian relationship. By correcting the magnetite and shale classification curves for the bypass inefficiency to underflow, and similarly correcting the coal classification curves for the bypass inefficiency to overflow, the corrected classification curves for the magnetite, shale and coal were reasonably parallel (considering that the coal has a range of densities). Using a value of five for the density of the magnetite, the displacement of the shale and coal curves corresponded to densities of 2.27 and 1.38 respectively for one circuit, although the data was not as good for the other circuits. This reverse classification mechanism was confirmed in a 140 mm diameter laboratory dense medium cyclone circuit using low density (1.20 - 1.30 RD) tracers, sized from 0.25 to 2 mm. These classification performance curves were corrected for bypass ineffiency (as above). The corrected curves were parallel and displaced according to tracer density, even though the lowest density tracers were reverse classified to the overflow. The data indicate that the rates of classification of all particles could be described by the same Stokesian relationship, regardless of the direction of travel, except for a narrow band at the partition density. Particles heavier than the partition density classified to the underflow, particles lighter than the partition density reverse classified to the overflow and particles identical to the partition density were not classified at all. Consequently it should be possible to simulate partition in dense medium cyclones, operating under free settling low density conditions, with a simple cyclone classification model, provided the partition density can be accurately calculated from, or correlated with the cyclone feed, underflow or overflow pulp densities. The tracer partition performance in the laboratory cyclone was an inverse function of the tracer particle size, as proposed by King and Juckes (1984) for medium/coal ratio in low density medium systems. Their sized coal data was parallel, with lower partition values due to a higher energy cyclone. Partition data with similarly sized tracers (Scott, 1988) showed a parallel shift to higher partition values due to the separate effects of higher viscosity medium and a larger diameter lower energy Cyclone.

Jan 1, 1993

New Zealand is an exposed part of a sub- continent that was detached from Australia when the Tasman Sea opened in the Late Cretaceous. The pre-separation rocks occur in three main belts. A western belt or terrane was part of Antarctica, was continuous with southern Australian rocks, and was moved eastwards in the Mid Devonian. A central belt of Hokonui and Caples rocks can be correlated broadly with the Gympie Terrane of eastern Queensland. It was an island arc, fore-arc basin and accretionary wedge system, and it was accreted to eastern Australasia in the Mid Triassic. The third belt consists of Torlesse rocks and was possibly emplaced over the Caples rocks by at least three pulses of strike-slip, in the Triassic, the Jurassic and the Cretaceous. The three episodes of strike-slip can be correlated with regional events in eastern Australia. Pre-Cainozoic New Zealand was an amalgam of terranes that had moved eastwards from south of Australia and southwards from east of Australia.

Jan 1, 1987

By Johnson CR, Wilkie G

The aim of the study was to use quantitative mineralogical measurements to predict the processing characteristics of an ore. Samples were taken from a wide range of concentrators processing ores of lead, zinc, copper and nickel. QEM'SEM was used to measure the characteristics of the ore feeding the plant. Concentrate product samples, together with plant operating data were used to give concentrate grade, recovery and grind size information. It was found that the mineralogical measurements correlated well with the metallurgical parameters indicating that these techniques will be very useful for making predictions in feasibility studies and simple plant optimization.

Jan 1, 1989

By Lauricella P. F, Hendri D

In the Mesel sediment-hosted disseminated gold deposit, the spatial distribution of hydrothermal alteration is controlled by steeply dipping faults and shallowly dipping lithologies. Hydrothermal alteration of carbonate rock is characterised by decalcification, dolomitisation and silicification. Intense argillic alteration occurs in a laccolithic andesite intrusion adjacent to decalcified and silicified carbonate units. Sulphide minerals (pyrite, realgar, orpiment, stibnite and cinnabar) accompany hydrothermal alteration and precious metal mineralisation. The trace elements Ag, As, Sb and Hg are zoned spatially throughout the deposit. Mesel contains a mineable gold reserve of 7.8 million tonnes at 7.3 g/t Au. Gold mineralisation is preferentially localised in carbonate rocks adjacent to and beneath the andesite intrusion. The ore body consists of a central, near-vertical, high grade "feeder" system flanked by tabular, inward dipping, moderate grade "ouflow" zones. Mineralisation is controlled predominantly by two steeply dipping faults with high grade (>10 g/t) gold zones centred about structural intersections and fault splays. Gold is submicron size and locked in very fine grained (

Jan 1, 1995