Search Documents

By K. Takahashi, I. Iwasaki

The methyl stretching vibrations for a series of normal xanthates, isoxanthates and normal amines were determined with the aid of an infrared spectro-photometer, and the results were compared with published information on the corresponding alcohols. The frequency shifts of methyl stretching vibrations may be attributed to the inductive effect of polar groups. The hydrogens in the shorter chain alkyl groups are somewhat polar and can be expected to interact with water molecules by hydrogen bonding. Contact angle, surface tension lowering, solubility, and critical micelle concentration appear to be related to the induced polarity of the alkyl groups. Traube's rule states that in homologous series of compounds solubility decreases and surface activity increases regularly with the size of the hydrocarbon group. Analyzing the work of transfer of a solute from solution to surface, Langmuir' interpreted this rule to mean that each CH2 group added to a molecule produced its effect independently of the others. It is also well known2 that the maximum equilibrium contact angle with sulfhydryl collectors is independent of the polar groups and of the sulfide minerals, and that it increases to a certain limit with the number of carbon atoms in the alkyl group. This observation is thought to demonstrate the orientation of the collector molecules at the sulfide surfaces. The dependence on the hydrocarbon chain length is usually explained as due to the screening of the force field of polar mineral surfaces.3-5 Here again, Langmuir's principle of independent surface action appears to be implied. Heteropolar compounds consist of nonpolar and polar groups, the former being the hydrocarbon group and the latter containing such electronegative atoms as O, N, S, P, or halogens. According to Palit6 the hydrogens in the alkyl groups are more electroposi- tive than in the paraffins owing to the negative inductive effect of the polar groups and a possibility that a hydrogen bond with water molecules ensues. Goto and Takenaka7 provided direct evidence of the inductive effect by measuring the shift of the C-H stretching vibrations of alcohols, acids, and alkyl bromides with an infrared spectrophotometer. Their approach appeared to be directly applicable to the studies of surface activity both at air-water and water-mineral interfaces encountered in flotation systems. The present article attempts to relate the C-H stretching vibrations of alkyl xanthates, alcohols, and amines with such flotation chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration. MATERIALS AND METHODS Normal xanthates from methyl to octyl inclusive and the isopropyl, isobutyl, and isoamyl xanthates used in this investigation were prepared in the usual manner.8 Normal amine hydrochlorides with carbon chain lengths of 1, 2, 4, and 6 were from Distillation Products Industries, of 8 from Archer-Daniels-Midland Co., and of 10, 12, 14 and 16 from Armour and Co. Normal propylamines, pentylamines and heptylamines from Distillation Products Industries were used both as received and as hydrochloride formed by converting the amines according to the procedure described by Li9 Perkin-Elmer Model 521 and 621 infrared spectro-photometers were used to investigate the spectra in the frequency region of 3050 to 2800 cm-' with frequency scale expansion. The accuracy of the frequency readings was within + 1 cm-1. The KBr micropellet technique was used to prepare the xan-thate samples for measurements, and the halocarbon mull technique was used for amines and amine hydrochlorides. EXPERIMENTAL RESULTS Fig. 1 shows the CH3 asymmetric stretching vibrations as a function of the number of carbons in the alkyl group for normal xanthates, isoxanthates and amines. Also included in the figure are data for normal alcohols and isoalcohols taken from the article

Jan 1, 1970

By S. N. Singh, M. C. Flemings

Results are presented of a study on the combined influences of ingot dendrite am spacing and thermo-mechanical treatments on the fracture behavior and mechanical properties of high purity 7075 aluminum alloy. The most important single variable influencing mechanical properties was found to be undissolved alloy second Phase (microsegregation inherited from the original ingot). Ultimate and yield strengths were found to increase linearly with decreasing amount of alloy second phase while ductility increased markedly. At low amounts of second phase, transverse properties were approximately equal to longitudinal properties. In tensile testing, microcracks and holes were invariably found to originate in or around second phase particles. Fracture occurred both by propagation of cracks and coalescence of holes, depending on the distribution and amount of second phase. IN most commercial wrought alloys, second phase particles are present that are inherited from the original cast ingot. These include, for example, non-equilibrium alloy second phases such as CuAl2 and impurity second phases such as FeA13 and Cr2A1, in aluminum alloys. A previous paper1 has dealt with the morphology of these second phases in cast and wrought aluminum 7075 alloy, and with their behavior during various thermomechanical treatments. In this paper we discuss the influence of the particles on mechanical properties and fracture behavior of the alloy. Previous experimental work indicating a direct and major effect of second phase particles on mechanical properties (especially on ductility) includes the work of Edelson and Baldwin on pure copper.' Also relevant are the many studies demonstrating the important effect of nonmetallic inclusions on the fracture of. steel.3'4 Work on aluminum includes that of Antes, Lipson, and Rosenthal5 who showed that a dramatic improvement in ductility of wrought aluminum alloys of the 7000 series is achieved by eliminating second phases. It now seems well established that included second phases play a dominant role in controlling ductility (as measured, for example, by reduction in area in a tensile test) of a variety of materials. There is, therefore, considerable current interest in the mechanisms by which second phase particles affect ductile fracture. Experiments done by various workers have shown that second phase particles or discontinuities in the microstructure are potential sites for nuclea-tion of microcracks and of holes,6-l3 which then grow and cause premature fracture and the loss of ductility. Theoretical attempts have been made to explain the observed phenomena; most are able to explain observations qualitatively, but lack quantitative agreement. Much experimental work needs to be done to aid extension of theoretical models. A recent review article by Rosenfield summarizes work in this general area.14 PROCEDURE Material used in the previously described study on solution kinetics of cast and wrought 7075 alloy1 was also used in this study. Procedures for ingot casting, solution treating, and working were described in detail in that paper. Test bars were obtained for material of 76 initial dendrite arm spacing (11/2 in. from the ingot base) and 95 µ initial dendrite arm spacing (51/2 in. from the ingot base) for the following thermomechanical treatments (solution temperature 860°F; reduction by cold rolling). a) Solution treated 12 hr, reduced 2/1, 4/1, and 16/1. b) Solution treated 12 hr, reduced 16/1, solution treated approximately 5 hr after reduction. c) Same as a) except solution treated 24 hr prior to reduction. d) Same as b) except solution treated 24 hr prior to reduction. e) Same as d) except solution treated 20 hr after reduction. Test bars were taken both longitudinally and transverse to the rolling direction. Transverse properties are in the long transverse direction; since the final product was sheet (0.030 in. thick), properties in the short transverse direction could not be obtained. Test bars were flat specimens, of gage cross section1/-| in. by 0.030 in. and 1/2 in. gage length. After machining the test bars, they were given an additional 1/2 hr solution treatment of 860°F and aged 24 hr at 250°F. Three bars were tested for each location and thermomechanical treatment, after rejection of mechanically flawed bars. The average results of these three bars are reported. Elongation was measured using a $ in. extensometer and reduction in area was determined using a profilometer to measure the area after fracture. INFLUENCE OF THERMOMECHANICAL TREATMENTS AND SECOND PHASE ON MECHANICAL PROPERTIES Results of mechanical testing are presented in Figs. 1 to 4 and in tabular form in the Appendix. A general conclusion from results obtained is that details of the thermomechanical treatments studied were important only insofar as they influenced the amount of residual second phase. Figs. 1 and 4 show the longitudinal properties obtained (regardless of thermomechanical

Jan 1, 1970

By I. Iwasaki, K. Adam

The oxidation behaviors of simple and complex chloride systems of copper, iron, nickel, cobalt, and manganese in a stream of oxygen were investigated using a thermogravimetric analysis technique. Their reaction mechanisms are discussed from stoichiometry, thermodynamic feasibility, and X-ray diffraction analysis of reaction products. The results are used to determine an optimum operating temperature of the selective oxidation step in a chlorination process for producing nonferrous metal chlorides, elemental sulfur, and ferric oxide from copper-nickel sulfide flotation concentrates.

Jan 1, 1985

By A. L. Hay

The Sydney coal field, the largest and most valuable in Nova Scotia, is situated on the northeastern coast of the Island of Cape Breton, extending from Mira Bay on the south to Cape Dauphin on the north, a distance of 30 miles, and has a general dip northeast under the sea. (Fig. 1. The field embraces the mining villages of Morien, Birchgrove and Reserve and the towns of Dominion, Glace Bay, Waterford and Sydney Mines. The city of Sydney is situated about midway between the northern and southern extremities of the field and on the western fringe of the productive coal measures. Sydney harbor crosses the coal field, cutting off direct rail connection between Sydney Mines and the greater part of the field to the southeast. (Fig. 2.) The coal measures are exposed in the cliffs on the coast line, which rise to an average height of 30 ft., and are almost continuous throughout the length of the field. The portion of the coal field under land forms a small segment of a circle, the greatest distance from the coast landwards is 9 miles, and it occupies an area of 200 sq. miles. The greatest distance developed seawards from the shore by mining operations is 2 miles. The strata maintain a regularity of dip at this distance, proving a submarine area of about 70 sq, miles. How much further the coal field extends seawards is unknown, but the indications are that it extends far beyond the present economical working limit and in all probability there is a vast submarine coal field. The productive coal measures are of Carboniferous age, these being underlain by beds of sandstone, locally classed as millstone grit, which define the southern limit of the field, while a spur of syenitic hills cuts off the coal-bearing strata on the north. Two main anticlinal folds having a general course easterly divide the field into three basins named from north to south: Sydney Mines-Lingan, Glace Bay and Morien. So far as the portion of the coal field already developed is concerned the general effect of these folds is to vary the direction and dip of the strata at different points of the several basins. The strata dip seawards at the average rate of 6 per cent. along the axes of the basins. On both sides of the several basins, the strata have a dip varying from 7 to 40

Jan 1, 1930

By G. C. Mudd, E. J. Myers

Within the last 15 years David Brown Gear Industries has manufactured approximately 200 large mill gears over 6m diam., 58 of them over 9 m and up to 12 m diam. The experience has not been without problems, due to a lack of clear understanding of the loads and stresses imposed on large gear wheels. American Gear Manufacturers Association (AGMA) practices suggest that a service factor be used for mill gears. But what is meant by "service factor"? The layman might be forgiven for believing that the term is synonymous with "safety factor," but this is certainly not true. The service factor is an aggregate of the following in some proportion: -An application factor, i.e., an allowance for the fact that systems do not run smoothly with uniform torque. -An ignorance factor covering the imperfections in the basic gear calculation. -Possibly a safety factor. In the following sections some of the ways in which the limits of applicability can be overstepped are discussed.

Jan 1, 1983

By Horace F. Silliman, Curtis L. Wilson, Eugene C. Little

The change in electrical resistance and Rockwell hardness (16-100-B) of copper alloys containing Ni2Si and Co2Si was determined by annealing the quenched solid solutions at various temperatures for various lengths of time. The rate of precipitation of Nisi, as measured by the rate of decrease of electrical resistance and increase of hardness, increased with annealing temperature up to a certain point, depending on the percentage of Ni2Si present. At these temperatures discontinuities in the rate: change occurred. Similar discontinuities in the Co2Si alloys were no The solubility of Co2Si in copper was found to be 5 per cent at 970" DISCUSSION (Robert F. Mehl presiding) R. I?. Mehl, Pittsburgh, Pa. (written discussion).—The electrical conductivity and hardness curves reported in this paper are interesting, particularly because many of the anomalies of the precipitation processes are evident from such curves. The title of the paper, however, is deceptive, for it implies that measurements of electrical conductivity and hardness are suitable to determine the rate of precipitation. Neither of these methods is suitable for a quantitative measurement of rates of reaction or of precipitation in the solid state. Electrical conductivity in some alloys shows an anomalous increase during the first stages of aging at low temperatures; it is notably sensitive to strain and to state of subdivision. I have plotted the conductivity curve representing the decomposition of the phase at 555" C. in the copper-aluminum system, given in the paper by Smith and Lindlief (Fig. 47, p. 93) as a rate of reaction curve, and compared it with the curve determined by area evaluation (Fig. 7); these two curves are not coincident. Hardness is likewise very uncertain, for it is so much dependent upon particle size. Of the various methods proposed for the study of rates of reaction and precipitation, the evaluation of volume of reaction product from the respective area of matrix and reaction product on the photomicrograph is the most trustworthy; suffering, perhaps, only from low sensitivity during the early stages. This method, used originally by Davenport and Bain and now by Smith and Lindlief, is suitable for

Jan 1, 1933

By F. F. Aplan, P. H. de Bruyn

The adsorption density of hexyl mercaptan was measured at the gold-solution and the gold-vapor interfaces. This collector is strongly adsorbed at low concentrations, a monomolecular layer being formed at the gold-solution interface at concentrations as low as 2 x 10'6 moles per liter. A maximum contact angle of 83 ± 3° is observed. From a thermodynamic analysis of the experimental data the changes in surface tension at the gold-gas and gold-solution interface are calculated. The data also suggest that the adsorption density of mercaptan at the gold-gas interface exceeds that at the gold-solution interface. In the equilibrium state, a simple flotation system consists of three phases, the solid to be floated, air, and an aqueous solution in stable contact along a line. During the process leading to this final state, a solid-gas interface is created at the expense of a portion of the liquid-gas and solid-liquid interfaces. This change of state is achieved by addition of a collector and, if necessary, suitable modifying agents to the system. By a combined application of the Gibbs Adsorption and the Young Equations, de Bruyn, Overbeek and Schuhmannl were able to show theoretically that the equilibrium distribution of the collector at all three interfaces determines the magnitude of the contact angle. Their analysis led them to conclude that the equilibrium adsorption density of the collector at the solid-gas interface exceeds its density at the solid- liquid interface. This paper succeeded in focussing attention on the neglected role of the solid-gas interface in flotation. In recent years the application of radiotracer, infrared, electrochemical and electro-kinetic techniques to studies of the solid-liquid interface2-5 enhanced our understanding of adsorption processes at this interface. Except for the measurement of contact angles, the solid-gas interface received no attention in fundamental flotation studies. In an attempt to apply the analysis of de Bruyn, Overbeek and Schuhmann to a simple flotation system, an investigation of the adsorption of hexyl mercaptan onto gold was undertaken. Gold was chosen as the solid phase in order to keep the number of dissolved chemical species in the solution phase to a minimum. Hexyl mercaptan (1 - hexanethiol) was selected as collector because its relatively high vapor pressure at room temperature makes it possible to obtain adsorption measurements at the solid-gas interface. This flotation system consists, therefore, of a pure solid phase (gold), an aqueous solution of a weakly dissociated collector (1 -hexanethiol), and a gaseous phase, nitrogen saturated with respect to both water vapor and mercaptan vapor. EXPERIMENTAL MATERIALS AND METHODS Materials: Liquid 1-hexanethiol (C6H13SH) was obtained from Distillation Products Industries and was further purified by double distillation. The purity of the final product was established by boiling point and refractive index measurements. For the adsorption studies from aqueous solution, the radiotracer element, sulfur-35, (half life 87.1 days, 0.169 Mev beta ray) was synthesized into the mercaptan by Tracerlab Inc., Boston, Mass. A close boiling fraction of the synthesized compound was used in the adsorption studies. The specific activity of the radioactive compound was 10 millicuries per gram.

Jan 1, 1963

By Orson Shepard

THE term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 19341. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner:. . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1936

By R. G. Green, R. L. Dowdell

LEAD POISONING as a result of eating lead pellets deposited in marsh areas is a cause of high mortality among ducks, geese, and other waterfowl ingested lead shot become trapped in the gizzard with gravel and are slowly ground away by the grit. Absorption of lead as it passes through the intestine in a finely divided state produces severe lead poisoning which is usually fatal. Ducks and geese with lead poisoning develop first a typical green diarrhea. Later, paralysis of the wing muscles prevents flight. As the poisoning continues with further grinding of the shot trapped in the gizzard, increasing paralysis reduces the bird to helpless-

Jan 1, 1937

By A. E. Outerbridge

I had the honor to present to the American Institute of Mining Engineers at the Pittsburg meeting, February, 1896, a paper having the foregoing title, in which I said : " It has generally been accepted as a fact that cast-iron, under the influence of repeated shocks, becomes brittle, and will finally break under a blow which otherwise it would have withstood. It will probably surprise metallurgists, therefore, to learn that experiment disproves the supposed fact, and establishes exactly its opposite. " The result of about a thousand tests of bars of cast-iron of all grades, from the softest foundry mixtures to the strongest car-wheel metal, enables me to assert with confidence that, within limits, cast-iron is materially strengthened by subjection to repeated shocks or blows." Three tables were appended showing increase of strength

Jan 1, 1905

By R. P. Rothwell

AT this our first meeting I beg to call the attention of the members of our Institute to what is certainly a question of the greatest possible importance to the industries we represent; and more particularly to the welfare of the coal and iron trades: I refer to the enormous waste of coal in mining and in its preparation for market, as now practised in our anthracite coal-fields. I t is a fact which many of you can certify to, that we are wasting fully me-half of all the coal in the veins we are now working, and there are cases, which might be mentioned where this proportion, immense as it is, has been greatly exceeded. The popular belief that our deposits of anthracite coal are "practically inexhaustible," is very far from being founded on facts. On the contrary, supposing the present rate of increase in the production to be maintained, it is probable that a maximum yield for our coal-fields would be attained in about fifteen years ; there are in fact some of our smaller basins where the principal veins are nearly exhausted and the production has already attained its maximum. There are others, again, where the depth attained-and it must be borne in mind that we commenced working at the surface outcrop moderate though it is (scarcely ever reaching eight hundred feet), has so increased the cost of mining as to imperil the capital invested, and though it requires but little foresight to predict the time when the difficulties of mining will be very considerably increased by reason of the greater depth, greater quantity of water, fire-damp, and other fruitful sources of cost, yet, ignoring these recognized facts, we continue to waste more than one-half of the coal where it is obtained with the least danger, expense, and trouble, that is, near the surface-either above water-level or at a moderate depth . below it. The inspection of almost any accurate mine map will satisfy you that, on an average, we leave fully one-third. of the coal in the ground as pillars to support the roof; in some places more than one-third thus remains, while it is very rare that less than one quarter is left. In almost every case this coal is absolutely lost, for it will very rarely pay to reopen gangways and lay roads to it after that portion of the mine has been abandoned. Is it necessary in all cases to support the roof, and where it is, may not some artificial

By K. E. Merklin, F. D. DeVaney

In the past most of the research in pelletizing has as its aim the production of a physically strong pellet. Now that this problem is solved, more attention is being paid to uniformity in grade and chemical composition. Consideration has been given in recent years to a study of additives which will make pellets partially or fully fluxed. Blast furnace tests show fluxed pellets to have advantages over both fluxed sinter and acid pellets. Lower slag volumes are used more frequently in the blast furnace and the uniformity of the charge, both physically and chemically, is becoming increasingly important. A considerable improvement can be secured by having all of the flux uniformly distributed through the pellets in a calcined state. A fluxed pellet, therefore, should be a superior product. The use of an ore burden that contains an appropriate quantity of fluxing materials is not new to the blast furnace industry. For years the Minette ores of France and Germany, the Clinton ores of the Birmingham, Ala., areas, as well as others, which are low in iron but contain calcium carbonate in sufficient quantities to give them self-fluxing properties, have proven economical. The adaption of the sintering process to the preparation of ore burdens provided a means for artifically associating the fluxstone with the iron ore prior to charging to the blast furnace. In 1944 Torpl discussed the effects of using lime in sinter made in Sweden on the sinter's metallurgical performance in a blast furnace. Hessle2 reported in 1945 on the advantages of using lime in sinter to increase the sintering plants' capacity and reduce fuel requirements. Robinson3 discussed the use of lime in Swedish sintering practice at the 1950 Blast Furnace, Coke Oven, and Raw Materials meeting. One of the suggested advantages was the combining of lime with silica to prevent the formation of a fayalite slag, which is difficult to reduce in the blast furnace. Nilson4 at the same meeting commented briefly on experimental work that had just started in the U. S. on the use of lime in sinter. The literature tends to indicate that most of this early work was directed towards improvement in sinter physical quality, and the fact that the feed to the blast furnace was partially fluxed was incidental. It was not long, however, before blast furnace advantages were being claimed. The matter was forcibly called to the attention of North American operators by reports of remarkable production records established by the Russians using fluxed sinter. The leading step was taken on this continent by the Steel Company of Canada in 1957; McMahon5 reported on the marked improvement in performance of an 18-ft blast furnace using fluxed sinter at its Hamilton works. Other North American operators quickly followed theStelco lead.

Jan 1, 1963

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By J. T. Eash, E. M. Wise

Many of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile properties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. Scope and Conclusions Tensile tests were carried out at room temperature and elevated temperatures up to 1100" C. on previously well annealed samples of platinum. palladium and several of their important alloys with compositions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100" C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested. The tensile strengths of palladium and the palladium alloy at 1100" C. are from 10 to 11.2 per cent of the room-temperature values. The elongations of platinum and its alloys tend to increase at temperatures above 600" to 800" C., while the two samples of pure palladium show a maximum at 600" C.

Jan 1, 1938

By J. T. Eash, E. M. Wise

Many of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile properties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. Scope and Conclusions Tensile tests were carried out at room temperature and elevated temperatures up to 1100" C. on previously well annealed samples of platinum. palladium and several of their important alloys with compositions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100" C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested. The tensile strengths of palladium and the palladium alloy at 1100" C. are from 10 to 11.2 per cent of the room-temperature values. The elongations of platinum and its alloys tend to increase at temperatures above 600" to 800" C., while the two samples of pure palladium show a maximum at 600" C.

Jan 1, 1938

By Wing L. Lew

LEAD, silver, and zinc, in quantities of economic importance are found in the Aguilar ore. The lead occurs as galena and the zinc as sphalerite and marmatite. The silver occurrence is more complex. Pyrargyrite and proustite have been identified only occasionally. Galena is silver-bearing and so are the various other sulphides, though to a lesser degree. The principal nonsulphide gangue minerals include calcite, quartz, wollastonite, rhodonite, and various calcium, aluminum, and iron silicates. A typical analysis of, the ore is: Pb, 11.2; Zn, 12.3; Fe, 4.4; Mn, 2.2; Cu, 0.15; S, 11.2; CaO. 7.6; "Insoluble," 50.1 percent; and Ag 263 g per ton. Crushing is done in three stages. The primary crusher at the mine is set to deliver about a 5-in. product. The crushed ore is then transported to the secondary crushing plant by a 3-km cableway where the general practice is to hold the product of the first Symons to about 1 in., and of the second Symons to about 1/2 in. When the ore is soft and rich the product of the first Symons is by-passed directly to the ball-mill bins. Dust control in the secondary crushing plant is effected by enclosing the dust-emanating sources and exhausting the enclosures with a Clarage No. 18 fan driven at 1300 rpm by a 20-hp motor. Use is also made of spray water at one or two critical places. Every effort is made to keep the air free from visible dust. Dust counts taken at the working places show dust concentrations of less than six million particles ner cu ft. The composition

Jan 1, 1947

By P. W. Andrews, R. B. Toombs

ECONOMIC STRUCTURE OF MODERN INDUSTRIAL ECONOMIES The role of minerals in modern industrial economies may be examined in several ways. There are relationships with the various sectors of the economy: the primary, secondary, and tertiary industrial groupings and activities. Mineral supply and demand activities can be measured in terms of national accounts criteria. The economic policy objectives of the modem industrial economy are based to a considerable extent on the needs of the nation for economic supplies of miner- al materials. There is an important role for minerals relative to national security in peace and in wartime and many national policies are directed toward ensuring adequate sup- plies of minerals. Environmental control in the modem industrial economy is increasingly concerned with matters related directly to the production and use of minerals and these matters, in turn, bear importantly on conservation in mineral supply and demand. Mineral polices include specific provision for research and development activities concerned with the production and the use of minerals. In all, national policy objectives will be shaped in considerable part by the circum- stances of mineral supply and demand: the relative degree of availability from domestic and foreign sources, the state of the mineral-processing industries, and the degree of development of the mineral-using industries, and per capita and total changes in requirements. Goods made from mineral raw materials are the basis of all advanced societies and although this is taken for granted, every country is continually dealing with problems of mineral supply and demand. Considering that in the first 50 years of this century the consumption of mineral materials in a highly Industrialized country such as the United States increased by six times while the population was doubling, it becomes apparent that if a country is to enjoy rapid economic growth it must have access to huge and ever-growing supplies of mineral materials at lowest possible cost. Adequate supplies of mineral materials and wise usage of mineral resources have always been among the most important determents of a nation's survival The importance of access to adequate mineral supplies is increasing every year and this has significant international, as well as national, implications because of the unique locational characteristics of mineral resources. It is generally acknowledged that no particular type of natural resource is essential to a high level of national income or to economic progress. A country's endowment of natural resources need not exercise a determining influence on the course of its national income over time, provided it is able to trade. What is required for economic progress is the availability of a substantial quanti-

Jan 1, 1976

By A. C. Freeze

The first use of electric punched card accounting machines as an aid in calculating reserves at the Sullivan mine in Kimberly, B.C., was made in January, 1948. At that time their use was limited to totalling individual reserve blocks for the various reserve classes and for calculating total metal content. The immediate objective was to increase speed, improve accuracy, and to effect some savings in labor that could be employed more usefully elsewhere. It was recognized also that the potential for achieving even greater advantages was excellent. The initial experiment proved so successful that it was inevitable that the use of the method would expand. Thus, for the past nine years assay data from core hole and development headings have been processed by these machines and the results integrated with the program of calculating reserves. It was also learned that the machines could store and classify a large amount of other information concerning the mining characteristics of each reserve block in addition to tonnage and metal content. This has proven very useful for the preparation of monthly production reports as well as in long term planning, in forecasting production schedules, and in analysing the results achieved.

Jan 4, 1961

By R. T. Keyes, R. B. Clay, L. L. Udy, V. O. Cook, M. A. Cook

Based on compressibility and stress wave velocity in rock, initial explosive loading conditions, the thermochemistry of the explosive and reasonable description of the pressure-distance relations behind the shock front, the distribution of energy between the products of detonation and the burden are estimated as a function of time for various loading conditions. These include 'powder factor', loading density A (fraction of borehole occupied by explosive), and the explosive itself. Factors responsible for rock fragmentation are discussed in terms of: 1) 'release wave fracturing', 2) 'shear wave fracturing', and 3) 'release of loading fracturing' or 'rock bursting'. Release wave fracturing appears to occur only in the immediate vicinity of free faces, and shear wave fracturing only adjacent to the borehole under normal blasting conditions. Rock bursting is thus considered to be the most important means of rock fracturing in blasting. Means for maximizing it are considered. The most important factors to consider include maximum available energy A, explosive density p1, loading density A and 'powder factor'. Maximum efficiency is attained in general by maximizing the A . p1 product. This is achieved by using high density explosives at a loading density of unity (A = 1.0). Ways for achieving this condition are discussed. The bulk-handled aluminized slurry blasting agents have the desired properties for achieving optimum conditions for high blasting efficiency based on the theory outlined herein. Factors considered most important in the blasting of rock are: 1) The maximum available energy A, determined by the heat of explosion Q and the mechanical efficiency ?, a factor intimately associated with the mode of application (A = Q at highest gas concentrations). 2) The 'borehole pressure', pb, or the maximum pressure developed in the borehole after passage of the detonation wave and before the burden has had time to move or become compressed appreciably. (Owing to the short duration of the detonation wave at any particular point in the borehole, the fact that the explosive may not always fill the borehole completely and the further fact that the burden may not actually see the detonation pressure, the borehole pressure is considered more significant than the detonation pressure p2 as a performance factor in borehole blasting.) The borehole pressure is determined by the explosion or adiabatic pressure, p3 , and the loading density, A, or the fraction of the borehole filled by explosive. 3) The physical conditions important in the application of the explosive are: a) The 'powder factor,' (We/Wr), or the ratio of the wt of the explosive to that of the rock being blasted expressed as lb per ton or more generally in lb/cu yd. b) The bulk density, p1 ?. c) The 'burden' or 'line of least resistance,' the spacing between boreholes, the geometry of the borehole pattern and sequence of firing. d) The physical and chemical properties of the rock, most significant of which are possible heterogeneties, such as faulting, prefracture, and greater than micro-scale chemical heterogeneities. (This factor is not considered here but deserves a great deal of careful consideration.) All of these factors need to be carefully considered in the most economical engineering of a blast. Here is considered firstly an outline of the present status of dynamic rock mechanics, particularly as it pertains to blasting. The factors pertaining to the most efficient application of blasting agents are also considered, followed by a discussion of methods of application to achieve optimum explosives performance. ROCK MECHANICS Dynamic rock mechanics is currently a rapidly developing science contributing greatly to a better understanding and consequently the more effective application of explosives in blasting of rock.1-22 Basic to the development of the science of dynamic rock mechanics were the advances of Goransen23 and the Los Alamos and NOL groups24-28 concerning rock and stress wave phenomena and the transmission and reflection characteristics of stress waves at interfaces between different media. Basing considerations on this new knowledge as well as new experimental methods of study (ultra-high speed streak and framing cameras and electronic timers) the theory of fracture and failure of solids under impulsive loading by stress waves developed rapidly.14,16,27-29 Also the

Jan 1, 1967