Search Documents

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993

By R. J. Morrell

The Bureau of Mines developed a ground support system for use with an underground coal auger. The system consists of inflatable airbags that are inserted in the holes as they are drilled, and then gradually deflated to provide controlled roof caving. This paper presents results of laboratory and field tests of the system that show it to be technically feasible.

Jan 1, 1988

By Keith Heasley

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 in (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.'s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysts of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. `The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

Jan 1, 2001

By John Cassie

The condition of roadways in the Deep Main seam at Asfordby mine, operated by RJB Mining (UK) Ltd, is strongly dependant on drivage direction relative to the maximum horizontal stress. The mine is laid out with gate roads driven approximately parallel to the maximum horizontal stress giving favourable drivage conditions. This has led to particulary difficult conditions for face installation headings which have to be driven to an increased width and at a high angle to the horizontal stress. A solution to the formation of face headings is described making use of stress relief with the face heading being driven in the zone of reduced stress surrounding a previous heading. In implementing this solution use was made of results from computer modelling and detailed monitoring of roadway behaviour. High reinforcement densities including cable bolts were used in supporting the headings. The experience provides an example of a traditional technique being applied more scientifically. The results obtained demonstrate the effect of stress relief and reinforcement methods in altering drivage conditions and suggest possible alternative strategies for the formation of future face headings in these conditions.

Jan 1, 1997

By Zuoliang Xiu

Experience indicates that rockbolting is the most efficient and cost effective means of supporting gateroads of retreating longwalls. However, gateroads supported solely by rockboltiug currently accounts for less than 16% of the 4500km of annual gatemad drivage in China According to a stated target of the Ministry of Coal Industry, this percentage should be at least 50% by the year 2000. Since the learning stage of the technology which is indicated by low drivage rates and frequent roof falls in rockbolted gateroads must be overcome , strategies for the application of rockbolting to gateroads have become the focus of discussions on this topic. This pap presents the recent development on longwall gateroad rockbolting technology in China The development work has concentrated on understanding the mechanism of rockbolting; establishing new design procedures of bolting parameters fix gateroad support upgrading the consumable; optimizing bolt installation procedures; adopting better roofbolting machines; and developing adequate secondary reinforcement technique. The authors believe that this development work together with the on-going wok in other aspects of gaterosd rockbolting, as discussed in this paper 9 represent the rational strategies for the application of rockbolting technology to a wider range of longwall gateroads in Chinese d mines .

Jan 1, 1997

By Herryal Anwar

The application of roof bolting technology to control the stability of roadways in coal mining within weak strata or under high ground pressure has improved progressively. One of several factors that affect the design of rock bolting is the immediate roof characteristics of the roadway. On the competent rocks, the mining conditions may indicate a high level of stability and a low density of bolting patterns may be adequate to control the ground stability. However, at a weak strata, the roadway will be affected by both horizontal and vertical stresses that may generate a high level of deformation in the immediate roof. This sensitivity of the roadway will require a mine plan design which consider the pillar sizes and sequences of extraction as well as a conservative reinforcement to maintain the integrity of the deforming weak roof strata. Rock bolting technology has been used to maintain the stability of roadways in Indonesia and Japan for a few years. In this paper the overview of the application of rock bolting reinforcement in Ombilin Coal Mine, Indonesia and Miike Coal Mine, Japan is given.

Jan 1, 1999

By C. P. Mangelsdorf

Between June of 1975 and November of 1978 Stateham and Radcliffe of the Denver Research Center of the Bureau of Mines in cooperation with officials of the Bear Coal Company of Somerset. Colorado Conducted extensive studies of the roof conditions in the Bear Mine. The purpose of the investigation was to determine the relationship if any between the length of time the roof was left unbolted and the subsequent stability of the roof. Using the comprehensive information available from Stateham and Radcliffe (1), (2), (3), (4) the author has proposed a design for a roof truss installation which might have been used in lieu of some of the bolting in the areas where bad roof was encountered. Historically roof truss installations like bolting patterns have been applied rather than designed. The purpose of the present paper is to demonstrate how with the information available, one might proceed through a semi-rational design. In spite of the very extensive documentation by Stateham and Radcliffe, it was still necessary to make some working assumptions. It is, therefore, not intended that the process here illustrated be used without modification in any other mine nor is there any criticism implied or otherwise, of the way in which Bear Coal Company conducted its operations. The author has never visited the mine in question. This paper is meant to be an encouragement award a more rational use of roof trusses in situations where it is economically and structurally reasonable to do so.

Jan 1, 1984

By George Mishra

In mid-1979, J&L Steel Corporation experienced rapid failure of pillars after only two weeks' operation with a combination of full retreat and partial mining in the 154 Road Section of its Nemacolin Mine, Greene County. The rate of advance of the "squeeze line" was very rapid for the first 500 feet, but it slowed down considerably as it approached some large coal blocks and gas well barrier pillars. After moving all section equipment out tc a safe distance, all accessible headings and crosscuts were filled with cribs and tri-set posts to prevent further spread of the squeeze. At one time, there was great apprehension by mine management that without implementation of some immediate corrective measures the safety of #3 airshaft and the only haulage and access road to the 8 Road mining area would be in jeopardy. In September, 1979, the U.S. Bureau of Mines established convergence monitoring stations outby the squeeze area. Readings were taken at weekly intervals until January, 1980, and monthly thereafter. Mathematical calculations, plot- ting of contour maps, and graphing of total convergence at different stations were used to follow and analyze the progress of the squeeze and provide guidelines for mining plans in the adjoining areas.

Jan 1, 1981

By Thomas P. Mucho

To document the performance of mine roof and roof support systems the U.S. Bureau of Mines (IJSBM) has been installing instrumentation at selected sites in U.S. coal mines. Much of this support and roof instrumentation has been installed in high stress conditions to maximize differences in performance. Summarized in this paper are the results of four such site investigations. The roof geology at the four sites is quite different and is quantified using the USBM's Coal Mine &f Rating (CMRR). The studies included detailed measurements of roof movement using multi-point extensometers, as well as measurements and monitoring of bolt loading. The investigations include developmental loading and abutment loading from longwall and room-and-pillar mining operations. Some of the issues examined are the effect of the horizontal stress field, the effect of installed tension (torque-tension versus resin bolts), the effect of reduced annulus bolt holes, and the differences between similar bolts supplied by different manufacturers.

Jan 1, 1995

By W. A. Cincilla

The use of resin-grouted rock anchors continues to gain popularity in underground wall mines in the United States. It is estimated that during 1985, more than 30% and as many as 35% of all roof bolts used employed sane from of resin anchor. The so-called 'combination' bolting systems, which generally utilize a resin pint-anchor, have also found increased application. This increased application is particularly true in poor ground, where more 'traditional' support measures have performed poorly. Virtually all resin bolts in use today in U.S. mines employ cartridge-type delivery systems, which in general, have produced good results under a variety of conditions. However, a host of inconsistent and sometimes uncontrollable variables may significantly alter the optimum bolt performance. These variables have been identified and are well documented in the literature (Snyder, et al., 1979; Kwitoweki and Wade, 1980; Serbcusek and Signer, 1985). The beau of Mines, Denver Research Center (DRC) conducted a major research project aimed at investigating the effects of selected aspects of installation procedures on resin-bolt performance. One objective of the project was to establish anchorage criteria for full column resin bolts installed in actual mining conditions. This piper describes the results of a particular study which focused on quantifying, through field tests, possible reductions in bolt anchorage due to installation of less-than optimum resin columns. These columns might result from losses of resin to surrounding strata, or non-compliance with recommended installation procedures. Over 1000 resin bolts having grout columns ranging from 12 inches up to 48 inches (full column) were installed and pull-tested at 13 underground test sites located in a total of 11 mines (Fig. 1). Four basic roof-rock types were included: shale, top coal, sandstone, and limestone. The majority of the bolts employed 3/4-in-diameter, 48-in-long, type 40 rebar having a minimum '~ated' yield point of 17,600 lb (8.8 tons). Actual yield strength may vary by manufacturer.

Jan 1, 1986

By E. Bane Kroeger

For many years, researchers around the world have been investigating coal pillar stability. Many have focused on trying to optimize the size of the pillars by examining stable and failed pillars in underground coal mines. For mines that are already in operation or companies that are opening a new mine adjacent to an existing mine where the pillar dimensions and stability can easily be determined, this is the preferred technique. However, when a new mine is planned for an area where there has been relatively little mining, then samples of the coal need to be drilled and tested for strength. Because of the fractured nature of coal, this lab testing is often problematic and may often yield poor results because of the limited size and number of samples that can be obtained from the core. To remedy this problem, research was conducted in the labs at SIUC to determine if improvements could be made when optimizing the size of pillars for underground coal mining in Illinois. Through a greater understanding of the relationship between dimensions and strengths of coal samples tested in the lab, it was hoped the in situ strength of coal pillars could be determined with greater accuracy. This could allow the extraction ratio to be increased and more of the coal resources in Illinois recovered without impacting the safety of the mine workers. Many different agencies around the world have published recommended minimum numbers of samples for strength determination based on the size of the coal samples. For two inch cubes, uniaxial testing of at least seven samples is recommended and this minimum number decreases to four when testing four inch cubes. However, the laboratory testing of coal from two seams thus far has suggested this number should be almost doubled to accurately determine the coal strength. Testing also showed there is a pronounced decrease in the variation in the strength of the samples tested as the dimensions of the sample were increased. From the testing results thus far, it is recommended that a sample size versus strength curve be constructed for every coal seam for Illinois. Creating such a curve will better determine both the minimum number of samples and minimum sample dimensions for that seam or region of a particular scam. A second set of tests were conducted in the laboratory to determine the increase in strength with reduction in height for samples with the same width and length. In Illinois, typical pillar dimensions are 40 to 80 feet (12.2 to 24.4 m) wide and long, with coal thickness varying from about 4 to 9 feet (1.22 to 2.74 m). This provides width/height ratios ranging from 4.5 to 17.5. Coal samples having width/height ratios ranging from 0.5 to 13 have been tested thus far. As with most pillar design formulae, the strength of the Murphysboro coal versus width/height ratio was linear and closely matched shape factors published by other researchers. The laboratory testing thus far has identified three factors that affect the strength of laboratory samples, the number of discontinuities, the angles of critical discontinuities, and the shape of the samples. The factor that probably had the most pronounced effect on the strength of the coal samples was the angle of critical discontinuities. This testing has confirmed that there is still a gap that needs to be bridged between the strength obtained from laboratory testing and the in situ coal strength predicted.

Jan 1, 2004

By Mictck Rataj

Methods of rock reinforcement in Australian coal mines are being advanced progressively through the better understanding of rock failure mechanisms around roadways and the-development of improved bolting hardware and installation techniques. It has been recognised that to improve the performance of rock reinforcement systems, the stiffness of the system as a whole has to be improved. New style bolts and accessories together with high pre-tensioned roof and cable bolts are being developed as a result. A number of the new techniques used to stabilise the roof, especially in weak roof/high horizontal stress areas have been site proven and are now currently used on a routine basis as a means of improving development rates and gate road stability during longwall retreat.

Jan 1, 1997

By Dave Forrester

Mining subsidence over shallow abandoned coal mine workings is unfortunately not an uncommon experience in the coalfields of North America and there is a significant knowledge and literature base addressing the phenomenon and related issues. From time to time, however, a case history arises which is outside the more routine occurrence. This paper addresses one such case and presents an overview of a subsidence Event above abandoned coal workings, which badly damaged a two-story High School building. The subsidence at the Cape Breton & Victoria Regional School Board (CBVRSB)'s MacDonald High School in Dominion, N.S., Canada on October 30, 2002 led to a detailed investigation. It was concluded that the ground movement and associated building damage had been caused by mining subsidence in underlying old underground coal mine workings of the 1890s, only 150 ft deep at the School. The Event was not isolated and a similar but smaller event happened nearby a few months later. The paper describes the events and summarizes the subsequent investigations and findings. The 17-year old High School building was eventually demolished.

Jan 1, 2004

By David Newman

Coal refuse impoundments and underground mines are frequently sited in close vertical and horizontal proximity in the valleys of the Southern Appalachian coalfield. The steep V-shaped valleys provide the volume necessary for slurry storage against a coarse refuse embankment that is constructed across the valley mouth. The presence of coal outcrops on the valley walls provides economic access to mineable coal seams that may be located under several thousand feet of overburden beneath the adjacent ridges. In some instances where the underground mine precedes the slurry impoundment, the type of mining (partial or complete extraction) and pillar centers were selected without consideration for the potential future use of the valley as an impounding structure. The high standard established for the design and stability analysis of the coarse refuse embankments is clearly illustrated by the absence of an embankment failure in the thirty-one years since Buffalo Creek. However, the recent Martin County slurry spill focused attention on a thorough geotechnical analysis to prevent a connection between the flowable slurry and the mine void. The overburden, roof, pillar, floor, and outcrop barrier stability are examined to quantify the break through potential. The strength and physical properties of the consolidated fine refuse are also important since this material is often the most well-defined and quantifiable barrier separating the slurry and mine void. Because each site is unique, the appropriate analysis ranges from the calculation of roof, pillar, and floor safety factors to detailed numerical modeling of the mine workings and the determination of ground deformation and strains resulting from mine subsidence. The method of refuse disposal may be altered to slurry cells where the accuracy of the mine maps, extent of mining, type of mining (development or retreat) cannot be reliably verified or the break through analysis does not produce an acceptable level of risk. Case histories from the Southern Appalachian coalfield are used to illustrate the application of methodologies to quantify the break through potential of coal refuse impoundments.

Jan 1, 2003

By Robert L. Schmidt

The support of underground openings by water is a natural phenomenon. Surface sinkholes, such as those that occur with some frequency in Florida, are attributed to a lowering of the water table resulting in the draining of existing limestone cavities. This withdraw the natural support and causes the surface subsidence. The role of water as a ground support medium was demonstrated in a mining situation during Bureau of Mines research on borehole mining of phosphate in St. Johns County, Florida. The borehole mining tool (BHT) incorporates a water jet nozzle and slurry eduotor in a single down- hole tool. The tool is lowered through a bore- hole into the ore zone, and an underground cavity is eroded by the motion of the water jet with the slurry simultaneously pumped to the surface. In addition to phosphate, the system has been successfully used in coal, oil sands, and uranium. The Florida phosphate ore is located at a depth of approximately 250 ft in strata that produce high water inflows. These factors preclude extraction by conventional methods, either surface or underground, but they present an ideal setting for borehole mining. Previous borehole mining research had led the researchers to believe that the system would only be effective in a void cavity, that is, a cavity where the water level is maintained below the water jet nozzle, so that the water does not impede the action of the let. It was soon discovered, however, that the void cavity presented ground control problems. The overlying strata started to cave soon after the support provided by the water was removed. This was an unacceptable situation as it adulterated the ore and threatened surface subsidence. Further tests wherein the size of the cavity -as reduced by cutting only a 30° arc also resulted in caving. A new concept, air shielding, was then introduced and tested. With this system, the water jet cutter was surrounded with a shroud of compressed air, thereby gaining the advantages of cutting in air while retaining the roof support afforded by a water-filled cavity. This arrangement proved to be highly successful. The air-shrouded jet was able to cut a cavity radius of about 18 ft, and the system production was 35 tph, which compared favorably to the production previously attained in void cavities. The borehole phosphate experience proves the efficacy of remote mining in a water filled opening. This system neutralises the hazards of heavy ground, and may, as in the case of the phosphate deposits, be the only viable alternative. It opens up the possibility of application in a wide range of deposits not only those amenable to hydraulic mining. Remote mechanical System might be developed using present robotics technology and then operated in water-filled openings.

Jan 1, 1986

By Stephen C. Tadolini

Cable supports offer several advantages over traditional secondary support methods. Cable supports enhance stress redistribution to pillars and gob areas, minimize or eliminate timbers and cribs which reduce ventilation capabilities, eradicate material handling injuries related to the placement of crib supports, and provide a cost-effective alternative to secondary support. The U.S. Bureau of Mines has designed and installed cable supports to improve the stability of tailgate entries in an underground western coal mine. Two entries closest to the Iongwall panel were solely supported with high-strength cables installed with cement grout. Basically, with modifications in the intersections, 360 ft of roadway nearest the longwall panel was supported with two rows of 22-ft-long cables installed on a 7-ft spacing. Approximately 250 ft of a second bleeder entry was supported with two rows of 16-ft¬long cables installed on a 7-ft spacing. Individual cable loads were monitored with hydraulic U-cells and pressure pads. The roof behavior was simultaneously monitored with differential magnetic sag stations and closure meters on 25-ft spacing during longwall panel retreat to evaluate the response of the immediate and main roofs. Cable supported gateroads appear to be a viable alternative in secondary support when compared to wood timbers and cribs. This paper describes the theory, application, and advantages of cable supports and presents the results of the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1993

By Yi You

A research has been conducted to study the long-term subsidence and its possible effects on surface structures In this research, the surface movements in areas when potential for developing long-term subsidence is high have been monitored over an extended period of time Long-term subsidence data have also been collected from other sources The avail- able data from this on-going research have been analyzed and the results is presented in this paper.

Jan 1, 1997

By H. Gene Wilson

Mobile Roof Supports (MRS) look similar to a longwall shield on crawler tracks. The MRS units offer a safe, productive method of extracting the 40% to 60% product left normally unrecovered in room and pillar mining. The units feature radio control, self-contained power units, crawler track drive, and a 600 ton yield. Cribbing and setting posts in retreat mining has been a necessary burden to production. The MRS reduces this burden. Long blocks of coal can be developed to further reduce move and tram time, thus increasing production. The MRS units have successful safety records. The workers are removed from the immediate fall area, and we feel back injuries have been reduced by the workers not setting posts. While MRS units have been damaged in falls, the other capital equipment has been unharmed. The MRS product line has undergone normal product improvement and evolution. Product evolution is seen in our development of machines for particular mine requirements. Through the continuing development of the MRS, Fletcher presents the coal industry with a safe, productive method of retreat mining with potential to develop new mining methods.

Jan 1, 1990

By S. S. Peng

The hydraulic powered supports have been employed in U. S. longwall mining for the past two decades. Yet the sciences of roof control at the powered supported faces remain largely unknown. In order to improve longwall roof control and increase production, a series of questions in longwall roof control should be studied and answered: what is the basic rules of roof behavior in longwall coal faces equipped with the hydraulic powered supports? What is the interaction between the roof, supports, and the floor What is the contact condition of the canopy with the roof, and consequently the load distribution on the canopy? Des the periodic roof weighting really exist in the powered supported face and if so, how does it affect the face area? This paper presents the preliminary analysis of underground observations and instrumentations in a longwall panel with 4-leg shield supports designed to address the questions mentioned above.

Jan 1, 1982

By John Ellenberger

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

Jan 1, 2003