Search Documents

By and M. V Roper, H. N. Engelbrecht

Quality control interventions emanate from process upsets and trends that move product quality beyond the natural variation expected in a stable process. The ability to detect upset conditions and react in an effective manner protects both resource utilisation and compliance to specifications. Product quality control on coal processing plants traditionally relies on the reference (combined sampler and laboratory) system to measure product qualities. The introduction of online analyser (OA) technology, applied in different configurations, creates a second source of measurement information for control decision making. The case study was done on the primary sample stream of the final product stream at Exxaro’s GG7 and 8 plants, part of the Grootegeluk complex. It explores the OLA system’s ability to meet the OEM performance guarantee, perform equally to the reference system without analytical delay time, and assesses the effort to achieve this performance in a by-line analyser (BLA) configuration. In the paper, a conceptual comparison of the two measurement systems is done and the theoretical and practical comparison of measurement performance is discussed. Results demonstrate that the OA outperformed the OEM’s performance guarantee and achieved similar levels of performance to the reference system without the response delay. Keywords: Online analyser (OLA), by-line analyser (BLA), coal quality measurement, measurement performance

Jan 1, 2020

By R. G. B. Pickering

Successful management of mining operations depend on the accurate and reliable measurement of performance as a monitoring instrument in a feedback and control loop. However, when changes are being considered, the probable effect of the change on bottom line results requires different measuring techniques incorporating an in depth understanding which can identify hot spots in the operation which exhibit strong sensitivity to change. The CSIR's Division of Mining Technology has therefore been devoting a considerable effort to the establishment of techniques which enable changes to be analysed in terms of their impact on the two key parameters describing mine performance, i.e. profitability and safety. This paper describes these techniques, outlines their application to some example situations and discusses planned enhancements. The first section of the paper addresses the profitability model, and this is followed by a section considering the mine safety model.

Jan 1, 1996

By M. Mpofu, G. Stenzel, F. Magweregwede, B. Maphalala, T. Kgarume

Surface coal operations in which mining activities are conducted above old underground workings experience hot holes after drilling. In a coal mine, hot holes are defined as shot holes, which after being drilled have an in-hole ambient temperature of 40°C or above or show a temperature increase of 3°C or more during monitoring. Hot holes and other cavities, such as cracks, pose health and safety risks to workers, such as exposure to hot air and high concentrations of noxious gases released from these holes. In addition, workers may be exposed to premature detonation of explosives caused by in-hole temperature increases and chemical reactions. To this end, Coaltech Research Association commissioned a project to develop a Best Practice Guideline for the management of hot holes. This paper is a compilation of the activities conducted in the development of the Best Practice Guideline between 2021 and 2022. The activities included a review of standard operating procedures and hot-hole temperature-measuring and -monitoring devices, and the assessment of current hot-hole procedures at selected mines. The results indicated that management of hot holes requires a focus on pre-emptive risk assessment of mining blocks, identification of hot holes using the correct temperature-measuring devices, and continuous monitoring of hot holes from the time of drilling until just before blasting. Hot-hole management accessories, such as polyvinyl chloride sleeves, were found to be effective in insulating the hot-hole emulsion from the rock mass temperature, thus preventing the potential for premature detonation.

Sep 9, 2024

Fathi Habashi, Chalcopyrite. Its chemistry and metallurgy. New York, McGraw-Hill, 1978. 165 pp. RI9,95. Loss prevention and safety promotion The Proceedings of the 2nd International Symposium on Loss Prevention and Safety Promotion in the Process Industries, Heidelberg, 6th to 9th September, 1977, are now available. Chemical reaction engineering The Proceedings of the 4th International/6th European Symposium on Chemical Reaction Engineering (4th ISCRE) held at Heidelberg, Federal Republic of Ge rmany, from 6th to 8th April, 1976, are available from DECHEMA Deutsche Gesellschaft fur Chemisches Apparatewesen, P.O.B. 970146, D-6000 Frankfurt/ Main, West Germany, at the price of DMlOO plus postage and packing. Books received The Institution of Mechanical Engineers Proceedings Volume 190. Tribos abstracts on friction lubrication wear. Published by BHRA Fluid Engineering, Cranfield, Bedford MK 43 OAJ England. Price £30 (UK), US$72 (Europe), Seawater corrosion handbook, edited by M. M. Schumaker. Noyes Data Corporation Publicity Department, Mill Road at Grand Ave., Park Ridge, NJ 07656. 494 pp. Australian mineral industry quarterly 31(1) 1978 and 31(2) 1978. Bureau of Mineral Resources, Geology and Geophysics, Box 378, Canberra City, ACT 2601 Australia. Subscriptions $8, individual number $2. Mineral and NIM reports Report no. 1996 The extraction of gold from chloride solutions. (10th Nov., 1978). Report no. 1898 Batch and pilot-plant tests on M erensky Reef ore from the Western Platinum Mine. (8th Jun., 1977; reissued 30th Jan., 1979). Report no. 1920 A mineralogical investigation of Mamatu'an and Wessels manganese ores. (15th Sep., 1977; reissued 3rd Jan., 1979). Report no. 1978 The preparation and certification of a referencesample of magnetite ore. (22nd Dec., 1978). Report no. 1998 Electrode response to the addition of zinc during the cementation of gold. (25th Jan., 1979). Report no. 2002 The spectrochemical determination of phosphorus, magnesium, and iron in phosphate rocks and sulphuric acid leach liquors. (26th January, 1979). Report no. 1992 The use of emission spectrometry for the determination of impurities in metals. (24th Jan., 1979). Report no. 2003 An electrodeless conductivity meter of improved sensitivity and reliability. (28th Feb., 1979). Report no. 2005 The spectrometric analysis of manganese-bearing materials with particular reference to ferromanganese slags and metals. (16th Mar., 1979). Report no. 2006 An examination of procedures for the analysis of dry powders by atomic-absorption spectrophotometry. (28th Feb., 1979). Report no. 2007 The instrumentation and computerization of a 25 MV.A submerged -arc furnace. (25th Mar., 1977; reissued 16th Mar., 1979). Corrosion The International Corrosion Council has decided to hold the next Internat ional Congress on Corrosion in Mainz, Federal Republic of Germany, from 6th to 11th September, 1981. Process control The First European Symposium on Real -time Datahandling and Process Control will be held in West Berlin from 23rd to 25th October, 1979. Geomechanics The 28th Geomechanics Colloquy, organized by the Oosterreichische Gesellschaft fur Geomechanik, is to be held at Salzburg on 18th and 19th October, 1979. Geosta tistics A short course on 'Geostatistics for exploration and production planning' is being conducted by the Applied Earth Sciences Department, Stanford University, California, from 27th to 31st August, 1979. Business administration The Twelfth Executive Development Programme of the Graduate School of Business Administration, University of the Witwatersrand, is to be held from 9th July to 17th August, 1979. The engineer and the law A series of four meetings on the above subject is being conducted by the Measurement, Computation and Control SubCommittee of The South African Institute of Electrical Engineers. Lead smelter for South Africa? The National Institute for Metallurgy and Gold Fields of South Africa are making a comprehensive joint investigation of the technical and economic viability of an integrated lead smelter. Conference on titanium The Fourth International Conference on Titanium will be held from 19th to 22nd May, 1980, in Kyoto, Japan.

Jan 1, 1979

By W. K. Brinsden

In August 1965, the late Mr Alan Smith, then Mill Superintendent at Gold Mines of Kalgoorlie (GMK), Australia, asked me to investigate the planting of vegetation on the GMK slimes dams in order to ease the dust problem in urban and industrial areas-a problem that is caused largely by dust from these barren slimes dams. My early sources of information were the comprehensive papers in various issues of the Journal of The South African Institute of Mining and Metallurgy. However, the climate of Johannesburg differs from that of Kalgoorlie. The average Johannesburg rainfall, which falls mostly in summer, is 730 mm, and the average maximum summer temperature is 26°C (top 34°C). The winters are cool, the average maximum being 18°C (low -7°C). Kalgoorlie, on the other hand, receives, on average, 257 mm of sporadic rainfall, has hot dry summers with an average maximum of 35°C (top 45°C), and cool winters with an average maximum of 18°C (low -2°C). My obvious choice was to look at established trees growing on the GMK lease. A number of Athel pines were growing vigorously adjacent to the Oroya mining and geology offices and also on a nearby sand dump. The Athel pine (Tamarix aphylla), which is native to North Africa, Asia, and India, was originally introduced into Australia in 1936 by Mr Essington Lewis, then manager of BHP. His cuttings were planted in Whyalla, where some difficulty had been experienced in finding trees and shrubs that would flourish despite the district's low rainfall. In August 1965, cuttings of approximately 20 cm length and 1 cm diameter were taken from the GMK trees, stripped of leaves, and placed in jars of water in the sun. When the cuttings had sprouted both leaves and roots, they were planted in local soil in tins (about 20 cm high and 10 cm in diameter), and watered daily. In October 1965, when the new shoots were about 8 cm long, the trees were transplanted onto a lower flat section¬approximately 30 m wide, 30 m long, and 2 m high-of the Trafalgar slimes dam. No additional soil or fertilizer was used, and the trees were planted in their tins, the bases of which had been removed (the tin would eventually rust away). A few common varieties of non-prickly cactus and two native salt bush (spp Atriplex) were also planted, but did not survive, probably because of the acidity of the slime. During the summer of 1965/1966, Kalgoorlie's rainfall was 88 per cent above the average, and this probably helped the trees to survive. The moisture content was usually about 2,5 per cent from about 10 cm below the surface, and the pH value of the slime (d80 approximately 75 µm) was about 6. The trees were watered twice a week for the first four months and then left untended. By 1974 they had grown to only about 0,7 m, which indicated that their growth in slime was very slow. Other Athel pines were planted on the wall of the dam, but did not survive beyond 1974, probably because of the steep (about 500) slope and the hardness of the walls, which were initially formed by hand-shovelling of the slime as the height of the dam was raised. Five of the six Athel pines planted in 1965, which probably reached maturity (approximately 5 m in height) in 1981-16 years after being planted-have survived. In the early 1980s, waste rock had to be dumped on the dam, but the management of KMA (now KCGM) took care to ensure that the trees were not buried. Trials are being conducted on other tailings dams so that the performance of cuttings taken from the trees on Trafalgar dam can be compared with that of cuttings taken at various sites in Western Australia. It might also be worth while for an attempt to be made to strike cuttings from Trafalgar dam in pots containing different mixtures of soil and slime.

Jan 1, 1991

By G. L. Dyer, R. D. Alorro, R. E. Browner

A potential new rare earth extraction process has been suggested (Lazo, et al., 2017) (Lazo, et al., 2018) based on converting the rare earth elements to solid phase rare earth oxalates in an oxalic acid leach. Oxalic acid consumption is a significant issue in the process, therefore to improve the viability of this proposed new extraction method, a process to recover oxalate from the leach solution and recycle oxalic acid is required. A review of the literature and confirmation through thermodynamic analysis of the potential options identified precipitation of calcium or ferrous oxalate as the best potential options. The use of metallic iron to both provide ferrous ions as a precipitant and reduce ferric ions in solution would provide the most economical option, however slow kinetics and unreacted iron created significant issues with this process. The direct use of ferrous ions, while faster and more efficient, produced a precipitate with relatively poor solid/liquid handling characteristics and would require an intermediate stage utilising calcium in regenerating the oxalate. Utilising calcium chloride and oxide created very similar precipitates with better physical properties than the ferrous oxalate and that a reasonable proportion of the oxalate could be recovered before neutralisation of the solution induced precipitation of other phases such as iron oxy-hydroxides and calcium phosphate. The produced calcium oxalate was easily converted to oxalic acid and gypsum via immersion in sulphuric acid. It was also found that there is a significant loss of oxalic acid due to factors other than rare earth oxalate precipitation during leaching. This leads to a maximum oxalate recovery in the range of 50 %.

Jan 1, 2020

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

By N. du Preez, J. Christie, F. Crundwell

Precipitation is a key process in the recovery of copper and cobalt. While there is a wealth of experience in operating precipitation steps, improving their performance remains challenging. Chemically, the reaction might be controlled by reaction kinetics, be limited by oxygen mass transfer, or be at equilibrium. In this paper, we examine these different operating regimes and demonstrate how they can be identified from plant operating data, process modelling, and pilot plant test work

Jan 1, 2023

By T. R. Marshall

SAMREC (The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves) Clause 7 notes that ‘Documentation detailing Exploration Results, Mineral Resources and Mineral Reserves from which a Public Report is prepared must be prepared by, or under the direction of, and signed by a Competent Person.’ Similar statements with respect to Competent Valuators (CVs) and Qualified Reserves Evaluators (QREs) are contained in the SAMVAL (South African Code for the Reporting of Mineral Asset Valuations) and SAMOG (South African Code for the Reporting of Oil & Gas Resources) codes respectively. What does it mean to be a Competent Person (CP) in the context of compiling/signing-off on SAMCODE (South African Mineral Code) compliant documents? What do the registration and experience requirements mean? Who is ultimately responsible for the report and what does such responsibility prescribe?

Sep 1, 2021

By G. C. Lindeque

"A downward trend in tyre life on haul trucks at an open pit iron ore mine prompted an investigation into the current tyre management strategy in order to improve tyre life. ‘Best practice’ was compared to the current tyre management strategy at the mine to determine aspects that could be improved. Aspects that showed significant room for improvement included employee tyre awareness, tyre pressure maintenance, and road conditions. For each of these aspects a plausible alternative was suggested.A new tyre management strategy was formulated as a step-by-step guide on how to implement the proposed changes. Each step introduces new initiatives but at the same time builds on the previous step’s success. A sensitivity analyses was performed to determine the impact of the proposed changes, with the variables being the reduction in the percentage of premature tyre failure, and the reduction of the site wear rate.The ‘most likely’ scenario showed an increase in tyre life of 41% for the Komatsu 730 trucks and 105% for the CAT 777 trucks if the entire tyre management model is implemented. This would result in a possible annual saving related to tyre usage of R9.2 million. OverviewThe study focused on the tyre life on the main haul fleet at an open pit iron ore mine. The haul fleet consisted of 17 Komatsu 730 (180 t) haul trucks and 12 CAT 777 (90 t) haul trucks.The haulage operation consists entirely of tyre-based haul trucks. Five per cent of the total mining budget is related to tyre costs. Since 2012 there has been a steady decrease in tyre life as measured in operating hours (Figure 1) due to the high percentage of tyres that fail prematurely. In 2014 a total of 41% of all tyres failed prematurely and 61% were classified as ‘worn out’."

Jan 1, 2016

"SAMPLING: THE IMPACT ON COSTS AND DECISION MAKING1. INTRODUCTIONFor years those in the minerals industry have been taking samples to assist them in making decisions; whether they be about investing billions of rand in a new mining operation, or simply whether a truck load of mineralised material should go to the mill or the waste dump, - we need a sample to help us make our decisions. This paper emphasises the importance and significance of sampling as a process, some of the associated technical problems and some of the advantages, especially in the light of traditional approaches that has usually left mine sampling to the least educated and lowest paid individuals on the mine. Perhaps the most important aspect that requires attention is the variability, usually measured in terms of precision, that tends to infect the sampling procedures. Francis Pitard 12 has stated: ""There is no such thing as reliable feasibility studies, unbiased ore grade control, accurate environmental assessments or effective process control, if you cannot identify and minimize the seven (ten) major sources of sampling variability. "" It is these ten sources of sampling variability and the way they arise that are briefly investigated. Variability is measured in terms of variances and rather than being self-compensating, there is good evidence to indicate that they are in fact additive at every step in the sampling and analytical process."

Jan 1, 2014

By W. A. Hustrulid

CONTENTS PART I The theory of percussive rockdrill operation. Blow frequency Piston impact velocity and blow energy Thrust requirements Prediction of penetration rate Drillsteel life Bit wear PART II Measurements of percussive rockdrill performance Thrust-penetration rate measurements Blow frequency Piston impact velocity and blow energy Prediction of penetration rates The effects of hole diameter Thrusts applied by men Bit wear Appendix I Experimental procedure and rockdrill and drill steel specifications Appendix II Piston impact velocities and energies PART III Practical implications. Provisions of adequate thrust Conclusions INTRODUCTION In South African gold mines some 100 million tons of rock are broken each year by drilling and blasting. Only minor improvements to this method of rockbreaking have been made since the general introduction of pneumatic rockdrills for stoping 50 years ago and, more recently, of drillsteels tipped with tungsten carbide. The combined total cost of drilling and blasting amounts to almost R0,50 per ton of rock broken, which is just short of one quarter of the direct cost of stoping or development. Rockdrilling accounts for about R0,25 of the total cost of rockbreaking, of which RO,12 represents labour costs and R0,13 the cost of drillsteels, rockdrill spares and power. Mine air compressors use over 7 X 108 kWh of electric energy a year, amounting to 7 percent of the total electric power used by the gold mining industry. The efficiency of percussive rockdrilling is, therefore, of considerable significance to mining costs. Over the past four years the Mining Research Laboratory of the Chamber of Mines of S.A. has been engaged in experimental studies of percussive drilling. These experiments were conducted at test sites on Robinson Deep Gold Mine and Vlakfontein Gold Mine, made available by Gold Fields of South Africa, Limited. Three rockdrills, designated types A, Band C, of different manufacture, were used in the experiments which involved the measurement of the following operating characteristics: 1. Throttle air pressure 2. Applied thrust 3. Penetration rate 4. Air consumption 5. Blows per minute 6. Drill steel revolutions per minute. The results of these investigations are presented in three parts. Part I, "The theory of percussive rockdrill operation" which provides a concise, mathematical description of the performance of a percussive rockdrill in terms of its principal mechanical dimensions and operating conditions, and an analysis of the bit and gauge wear of drillsteels. Part II, "Measurements of percussive rockdrill performance" in which the experimental results are presented in terms of thrust-penetration rate curves at different throttle air pressures and throttle pressure-air consumption curves, which are shown to agree well with the predictions of theory. In addition, data relating gauge wear on the drillsteel and penetration rate to the distance drilled are discussed. Part III, "Practical implications" in which an analysis of the status of thrusting devices is made and the benefits that would derive from using uptimum thrusts are discussed.

1. New books Extractionmetallurgy'81. London, Institution of Mining and Metallurgy, 1981. 441 pp. $40. Structures and properties of engineering alloys, by W. F. Smith. London, McGraw-Hill, 1981. 512 pp. R89,65. Rock and mineral analysis, by W. M. Johnson and J. A. Maxwell (editors). 2nd ed. New York, Wiley, 1981. 424 pp. $40. Mining methods and equipment, by Mining Information Services. London, McGraw-Hill, 1981. 218 pp. International directory of acronyms in library, information and computer sciences, by P. M. Vaillancourt. New York, Bowker Publishing Co., 1980.516 pp. 2. New journals Trends in analytical chemistry (TRAC), Amsterdam, Elsevier, 12 issues per year. Subs. for Volume I (16 issues) D.H 95.50. Engineering management international, Amsterdam, Elsevier, 4 issues per year. V.S. $32.50, D.H. 70.00. 3. Mineral policy sector publications Mineral Bulletin MR 188. Vanadium: an imported mineral commodity. $3.60. Mineral Bulletin MR 190. Canadian mines: 1980 perspective. $3.00. Canadian mineral survey 1980, by the staff of Mineral Policy and Energy Sectors. $1.00. 4. NIM reports Report 2090 Observations made during the dig-out of a 48 MV A ferrochromium furnace. Report 2110 The investigation of a fracture on one side of a skip bridle in a mine shaft. Report 2111 Pilot-plant tests for the recovery of chromite and the noble metals from the UG-2 Reef at Maandagshoek. Report 2112 The behaviour of UG-2 chromite concentrates during smeUing. Report 2113 M uUivariable control of a milling circuit at East Driefontein Gold Mine. Report 2115 Estimation of material variation in powdered materials Report 2116 Optimum operation of a direct-reading spectrometer with excitation by a 5 kW inductively coupled plasma torch. Report 2121 Five robust indicators of central value. Report 2124 The direct determination, by differential pulse anodicstripping voUammetry at the thin mercury-film electrode,of cadmium, lead, and copper. Report 2127 The preparation of a reference material of South African zirconium concentrate from Richards Bay. Report 2128 The determination, by differential pulse anodic-stripping voltammetry at the thin mercury-film electrode, of cadmium and thallium in six NIMROC reference materials Report 2130 The organizing of conferences. Research grant The Board of Directors of International Precious Metals Institute in conjunction with Gemini Industries, Inc., a California-based refiner of precious metals, recently announced a Gemini Research Grant of $3000 will be awarded annually to a graduate student who is pursuing studies in metallurgy, chemical processes as it pertains to precious metals, or materials sciences, and who is performing or planning research studies in the precious metals. Accidents and diseases The Third International Colloquium for the Prevention of Occupational Accidents and Diseases in the Iron and Metal Industry is to be held on 15th and 16th June, 1982, in Palma de Mallorca, Spain.

Jan 1, 1981

1. Journals Marine Geotechnology, edited by R.C. Chaney. London, Taylor & Francis (Rankine Road, Basingstoke, Hants RG 24 OPR, OK), 1988. vol. 8, $50. Published quarterly. Mineral Resources Engineering, edited by C.T. Shaw. London, Taylor & Francis (address as above), 1988. vol. 1, $99. Published quarterly. 2. New publication World mining map of non-ferous metals (with 4 regional maps and a booklet). Reinhard Ryborsch (Postfach 2105, D-6053 Obertshausen bei Frankfurt am Main, West Germany). International edition: bilingual, English and German. 7 colour-print: Size (unfolded) 138 X 100 cm. US$ 19 (excl. mailing) for folded map with hard cover (Order No. 61-4); US$ 25 (excl. mailing) for unfolded (flat) map with hanging strip (Order No. 62-2). 3. Mintek reports Report M326 Crevice corosion and other localized corosion behaviour of 3CR12 corosion-resisting steel in synthetic minewaters, by D. Howarth. May 1988. 28 pp.Report M332 The carbon-regeneration furnaces at Mintek, by P.M. Cole and P.J. van Staden. Nov. 1987. 31 pp. Report M344 The flotation of pyrite with amine colectors, by R.D. Hil, E.W. Giesekke, and P.J. Haris. Mar.'1988. 25 pp.Report M345 The substitution for chromium in steels: Progress and trends, by M.B. Cortie. Mar. 1988. 14 pp.Report M346 The direct reduction of sulphur dioxide to elementalsulphur, by I. Henderson. Mar. 1988. 30 pp.Report M349 The optimization of a process using weak-base resin for the recovery of gold from plant solutions and pulps, by A. Mehmet. Apr. 1988. 17 pp. Report M353 The determination, by ion-interaction chromatography, of sulphur species in cyanide solutions, by Pohlandt-Watson, M.J. Hemmings, D.E. Barnes, and a.w. PansL Jun. 1988. 7 pp. Report M355 A laboratory-scale continuous-feed resistance furnace, by K.P.D. Pery, A.S.E. Kleyenstiber, andC.T. Logan. May 1988. 9 pp. Report M357 The determination of minor and trace elements in activated charcoal, by RT. Eddy and G.J. Wal. Jun. 1988. 14 pp. Report M358 The sensitive determination of germanium by atomicabsorption spectrophotometry using electrothermal atomization, by G.D. Marshal. Jun. 1988. 11 pp. Report M92D The recovery of tin and tungsten from various zones of the Van Roois Vley deposit, including setling and filtration, by C.F.B. Coetzee. First issued Apr. 1983; reissued Apr. 1988. 40 pp. World Environment Day Symposium* Mintek auditorium in Randburg was the venue on Thursday, 2nd June, 1988, for more than 200 interested delegates at the annual World Environment Day Symposium, organized jointly by the Federation of Societies of Professional Engineers (FSPE), The Environmental Planning Professions Inter-disciplinary Committee (EPPIC), The Habitat Council, and The Associated Scientific and Technical Societies of South Africa (AS&TS). The theme 'Cultural and Historical Conservation' was adapted from the theme of the Department of Environment Affairs for the 1988 Environment Week.

Jan 1, 1988

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017

By P. L. Moolman

An approach to the design of a tailings disposal system is presented using an example from a platinum project on the eastern limb of the Bushveld Complex as a base case. The design is driven by two inputs: namely, maximizing water recovery and minimizing power cost, expressed as cubic metres and kilowatts per ton of solids deposited on the tailings storage facility respectively. The approach considers low-, medium-, and high-density platinum tailings and uses material-specific aspects such as thickening and rheology to determine the most economical option. An analysis based on direct capital and operating cost (water and electricity) shows that the medium-density scenario results in the lowest total cost per ton of tailings deposited, even though this system results in the highest electricity consumption per ton of tailings deposited. As the cost of water and electricity is likely to increase in the future, the higher-density tailings disposal options become more economical, with the paste option the preferred option.

Jan 1, 2012

This paper describes the extraction of gold, as the anionic aurocyanide complex, from solution by strong- and weakbase anion-exchange resins. The effects, on the rate of extraction and the loading capacity for gold, of parameters such as pH, temperature, ionic strength, agitation, and the presence of competing anions are reported. The elution and regeneration of strong- and weak-base resins will be examined in a second paper. A third paper in this series will present the results of several smallscale pilot-plant investigations carried out with strong- and weakbase resins In cyanide pulps from various South African gold mines, and will compare the metallurgical performance of resin-In-pulp with that of the carbon-in-pulp process.

Jan 1, 1984

By R. Kumar, N. R. Mandre

"The beneficiation of iron ore slimes by selective flocculation was studied. Polyacrylamide (PAM) and guar gum were used as flocculant, along with sodium hexametaphosphate (SHMP) as a dispersant. The samples collected were initially subjected for chemical and mineralogical studies. The mineralogical studies indicated the presence of haematite and goethite as the principal iron-bearing minerals, with quartz and kaolinite as gangue minerals. The selective flocculation tests showed that the Fe grade can be enhanced from 58.24% to 64.60% Fe at a recovery of 66.33% using polyacrylamide as the flocculant. A Fe grade of 63.20% at a recovery of 68.04% was obtained using guar gum as flocculant. The efficacy of the studies was analysed using a separation index, which indicated that the higher separation index was obtained with the tests employing polyacrylamide as the flocculant. IntroductionIndia is endowed with huge reserves of highgrade iron ore and is one of the prominent producers in the world. As the high-grade iron ores have been exhaustively mined, it has become imperative to use low-grade iron ores, fines, and slimes to meet the growing demand. Also, generation of fines and slimes during mining and processing contributes to loss of minerals to the extent of 30% of the total value (Mandre and Panigrahi, 1997). These fines/slimes are often discarded as waste into tailing ponds, containing considerable amounts of iron. Therefore beneficiation of tailings/slimes has become necessary for optimal utilization of the resources.In recent years, interest in recovery of valuable minerals from low-grade ores, slimes, and tailings has increased worldwide. These activities are initiated not only to recover minerals but also to address various environmental issues associated with fine particle treatment. The literature reveals that several technologies have been employed in this regard, including flotation, advanced gravity separation, and high-intensity magnetic separation. However, these processes are found to be ineffective for fine particle treatment due to lower collision probability in flotation, decreased gravitational effect in gravity separation, and reduced drag force in magnetic separation, among other factors (Batisteli and Peres, 2008; Das et al., 2007; Dworzanowski, 2012; Rocha, Caneado, and Peres, 2010). Therefore, it is in this regard that selective flocculation has gained importance in treating slimes in recent years."

Jan 1, 2017

By J. O. Roux

The Impala Platinum Limited Base Metals Refinery in Springs, South Africa, refines convertor matte containing base metals and PGM?s (platinum group metals) using a hydrometallurgical process. In addition to a PGM-rich concentrate that is further refined, the Base Metals Refinery produces nickel (in powder or briquette form), copper cathodes and cobalt powder. Five leaching stages are utilized to remove the base metals and impurities from the PGM concentrate. The project described in this paper involves a radical redesign of the second stage leach autoclave with the aim of reducing maintenance costs and downtime, increasing throughput and ensuring a safer working environment. The second stage leach process at the Base Metals Refinery, produces a PGM-rich residue through the extraction of copper and any remaining base metals from the first stage leach solid residue material. Leaching is performed in an autoclave operating at a pressure of 600 kPaG and a temperature of 140°C to 150°C. Concentrated H2SO4 is added to the feed to produce a solution with a free acid content between 10 and 30 g/L and a pH of less than 2. Oxygen is passed into the 1st and 2nd compartments of the autoclave. As a result of the aggressive, highly oxidizing conditions within the autoclave, the original design utilized a heavy wall carbon steel shell with lead lining and two layers of acid bricks. The bricks acted as a wear resistant material and ensured a low surface temperature at the skin of the lead lining, whereas the lead lining acted as a corrosion barrier to protect the steel shell. These brick lined autoclaves were heavy, maintenance intensive and prone to catastrophic failure. A radical autoclave redesign was needed to reduce the high costs of manufacturing, installation and operation. Finite element modelling was used to optimize the design and various high alloy materials were investigated for the application. Based on extensive test work, the carbon steel shell was replaced with duplex SAF 2205 stainless steel in the new design. The use of this highly corrosion resistant material, eliminates the need for the lead and brick linings and reduces the wall thickness requirements substantially, resulting in an increase in the available volume for the same external shell dimensions. The vessel is welded in circular sections to form an elongated, impermeable, cylindrical body, with several agitator nozzles and compartments. The first new duplex stainless steel unit has been in continuous operation for more than 24 months and its performance has exceeded the highest expectations. The design was so successful that a patent has been registered. The major benefits of the new stainless steel design include increased throughput, improved performance, less downtime and a safer working environment. Lead has been eliminated and replaced with a more environmentally safe material, and the total lifespan of the vessel has been extended. In addition, the autoclave project has made significant developments in advancing the field of welding and optimizing the integrity of welding quality standards in South Africa.

Jan 1, 2009

By I. Mitov, A. Stoilova, D. Krastev, B. Yordanov

We present three technological scenarios for the recovery of valuable components from gangue, stored in the tailings dam at Kremikovtzi metallurgical plant in Bulgaria, into marketable iron-containing pellets. In the first approach the iron concentrate was recovered through a two-stage flotation process, desliming, and magnetic separation. In the second proposed process, the iron concentrate was subjected to four sequential stages of magnetic separation coupled with selective magnetic flocculation. The third route entails the not very common practice of magnetizing roasting, followed by selective magnetic flocculation, desliming, and magnetic separation. The iron concentrate was pelletized in a laboratoryscale pelletizer. Each technology has been assessed with regard to the mass yield of iron concentrate, the iron recovery. and the iron, lead, and zinc content in order to identify the most effective route.

May 1, 2021