Search Documents

By K P. Crameri

The Beta Hunt orebody is situated on the south western limb of the Kambalda dome. It is one of the nickel occurrences in the area which fall into the category of æKambalda Style OrebodiesÆ. These orebodies are renowned as being continuous uniformly mineralised ribbons of nickel sulfide mineralisation. Interestingly, Beta Hunt does not conform to this notion of continuity and uniformity and is in fact highly irregular in its ore distribution due largely to the influence of post depositional structure. In an attempt to understand the ore distribution at delineation stage rather than development stage a detailed footwall topography model is created using all available drilling data. To augment this drilling data, the routine use of downhole EM and borehole radar has been introduced to provide data beyond the confines of the drill core to enhance the geological interpretation of the footwall topography and the distribution of the mineralisation. The implementation of a detailed footwall model and the use of downhole geophysics has proved to be very effective in resolving the orebody complexity issues. Ongoing development of the methods used will continue to refine the interpretation of the geology to enable more efficient extraction of the orebody.

Jan 1, 2006

By P Holtham, R Dunne, D Stoll

Flash flotation is a process designed to remove coarse, liberated, fast floating minerals from hydrocyclone underflow. Irrespective of liberation, coarse particles would normally remain in a grinding circuit until they are reground fine enough to report to the hydrocyclone overflow. Additionally, minerals of high density also report to hydrocyclone underflow despite being fine in size and/or liberated because hydrocyclones separate on the characteristics of both particle size and density. Dense particles continually reporting to the hydrocyclone underflow can lead to over-grinding and the production of ultra fine particles. These particles exhibit slow flotation kinetics and thus are difficult to float in conventional flotation circuits. Therefore, removing coarse, liberated particles from the hydrocylcone underflow by flash flotation has the potential to improve recovery and can improve dewatering unit operations and reduce grinding costs.The impact on the overall performance of the flotation circuit by removing coarse, fast floating minerals prior to conventional flotation is not well understood. Ultimately, predicting the overall recovery improvement provides the justification for the installation of a flash flotation cell within the milling circuit. This paper will describe attempts to estimate flash flotation recovery improvements to the overall circuit using kinetic data from simplified batch cell flotation tests combined with limn-based modelling techniques.CITATION:Stoll, D, Dunne, R and Holtham, P, 2012. Modelling the impact of flash flotation from batch cell flotation tests using limn, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By J Pearce, M Barteaux, S Pearce

The prediction of how waste materials will evolve geochemically within waste storage facilities has been the subject of hundreds of thousands of hours researched by geoscientists globally. Despite the quantity of research there are a number of significant areas of uncertainty that remain as partially resolved issues. One of the most significant issues is the applicability of scaling laboratory test results to field conditions, and the use of laboratory data for predictive calculations to determine geochemical evolution of waste materials in the field. This issue has arisen predominantly as a result of the relative paucity of field monitoring data from waste rock storage facilities (WRSFs) and the fact that laboratory test methods are not typically linked to specific field conditions; rather they are based on generic standardised methods and designed primarily to simulate accelerated weathering conditions that do not relate to field conditions in a linear manner.To address these specific issues the authors have in the last two years made significant progress in the development and deployment of advanced field monitoring equipment within numerous WRSFs. O’Kane Consultants (OKC) has previously reported the findings from data collected from these monitoring installations in a number of papers presented throughout 2013–2014. This valuable site data has subsequently been used by OKC as the basis to design and engineer advanced customisable site-specific kinetic leach columns at OKC’s geochemistry research laboratory. These columns represent an important advancement in kinetic column assessment methodology as they have been designed to replicate the field internal conditions within waste facilities.Key features of the columns include their capacity, size and technical specifications; including fully programmable solenoid-controlled air supply with variable flow and pressure control and in-line heating option, automated temperature control and monitoring, automated oxygen consumption and carbon dioxide production monitoring, and soil moisture/matric suction monitoring.This flexibility of the design not only allows for more accurate field-based assessment of pyrite oxidation rates (POR) but also assessment of the potential effectiveness of waste management options such as deposition within a reduced oxygen environment, for example, as simulations of reduced net percolation rates or oxygen ingress rates can be accommodated.CITATION:Pearce, S, Pearce, J and Barteaux, M, 2015. Advanced customisable leach columns – a new kinetic testing method to simulate site-specific conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Kapoor M. L

EMF measurements were performed in the temperature range of 933-1095 K to determine the thermodynamic properties of oxygen dissolution in liquid lead and lead-tin alloys with tin in the dilute concentration range of 0 to 6 atom per cent. The oxygen in the Pb-O system was varied by equilibrating with (PbO) slag, and that in the Pb-O-Sn system was varied with the addition of lead oxide. Wagner's interaction parameter approach was used to evaluate the self interaction parameter and ternary interaction parameters at different temperatures, to yield: E8(pb) = 97.35 - 113.27 x 103/t Eo(pb) = 139 - 20.616 x104/1' Quasichemical formulation was employed to yield Inf to reveal the effect of tin on oxygen in lead. Results have been predicted on the basis of classical models and those obtained using the QCT approach of Alcock and Richardson at Z=2 have been found to agree with the experimental Data.

Jan 1, 1992

By M S. Cassola

It’s expected that the world economy will face a stable and continuous growth in the demand of iron ore, reaching more than two billion tonnes per year within the next year. After decades exploiting resources with high content of iron ore, now the industry faces the challenge to exploit and beneficiate more complex ores.According to the industrial practice, the flotation technology is one of the most important and effective beneficiation processes to deal with low-grade iron ores around the world. However, even with this, it is still necessary to search for new processing routes or promote the optimisation of the existing circuits.The broad application of this technology is an outcome that deeply relies on the proper selection of flotation chemicals specifi cally designed for each system. New collectors are in continuous development as flotation performance significantly relies upon their optimisation.The reverse iron ore flotation in Brazil, mainly constituted by haematite and quartz, uses ether amines as collector for silica minerals and caustic corn starch as depressor for haematite. The process selectivity is highly impacted by the features of the etheramine, such as:• mono or di-etheramine,• neutralisation degree,• chain length,• branched or linear chain,• the flotation pH, and• the size distribution of the flotation feed.This paper describes the experience obtained from laboratory and industrial trials on different ores, conducted to improve the selectivity and recovery in the reverse iron ore flotation by selecting the required collector for low-grade ores.

Jul 11, 2011

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By Kajioka H, Nakamura Y

Na2CO3 is a powerful flux for both dephosphorization and desulphurization in oxidizing atmospheres. In order to study refining with Na2CO3 and the nature of the Na2CO3 slag itself, hot metal (4Kg) was melted in Al203 crucibles in a high frequency induction furnace and oxidised with oxygen under Na2CO3 slag. The behaviour of Na2CO3 at high temperature was observed by thermobalance. It was found that dephosphorization ceases in a few minutes and [,P] after refining is easily lowered to less than 0.010%. [%P] after refining is affected by [Si], [P] of hot metal, the refining temperature and the consumption of Na2CO3. Desulphurization also ceases in a few minutes but it shows curious behaviour, increase of [S], decrease of (S) and increase in sulphur lost, during the latter half of run. [%S] after refining is also affected by [P] of hot metal, the refining temperature and the consumption of Na2C03o

Jan 1, 1980

By Matsuo T, Uga Y

The tunnelling work to construct a sewage trunk line designed by the Sewage Bureau of Kobe City along north side slope of Rokko mountain range incorporated an all ground condition type (broad spectrum) TBM with slurry transport system with jet pump manufactured by Kawasaki Heavy Industries, Ltd. Boring dia. of the tunnel measured to 2.0 m. The construction planning and implemen- tation were done by Ohbayashi Corporation, the general contractor. The heading way was 3342.4 m in overall length.; construction work ran from April '84 to June '85. The max. daily progress marked 31.9 m and the max. monthly progress 493.1 m according to the relevant record. The machine proceeded with the work under geological conditions featured with conglomerate, rhyolite, tuff breccia and slate, whereby soft soil zone mostly of clay was encountered in a limited area. In the latter case, however, steel segments were substituted for supporting steel ribs. The tunnel was routed beneath a meandering road with the result that more than 40% of overall length show a curvature of 50 to 200 m radius.

Jan 1, 1987

By Miller JD, Ye Y

The Air-Sparged Hydrocyclone (ASH) has been developed for the fast and efficient flotation of fine mineral particles in a centrifugal field during the past decade at the University of Utah. Over the years, the air-sparged hydrocyclone unit has shown promising potential for the flotation of copper porphyry ore, low-grade placer gold and auriferous pyrite ores, various industrial minerals, and fine coal cleaning. Many fundamental studies including the X-ray computed tomography (CT) analysis have been carried out in order to understand the multiphase fluid flow phenomena associated with ASH flotation. With data available from these studies, it is now possible to construct more accurate ASH flotation models for different applications in order to analyse the behaviour of the system and to optimise design and operating variables. The ASH flotation model developed in this paper is based on the data given in `Air-Sparged Hydrocyclone/Advanced Froth Flotation Fine Coal Cleaning', Final Report, DOE Contract No DE-AC-88PC88853, submitted by Pennsylvania Electric Company (PENELEC), December 1989. Data from several hundred experiments with the two-inch ASH-2C air-sparged hydrocyclone (capacity 0.1 - 0.3 tph dry coal) are available from the report and have been used for this analysis. In the past, a preliminary model based on limited data had been developed. The current study, however, emphasises the global behaviour of the ASH system by utilising almost all the data from the report for the purpose of scale-up and industrial application. There are two parts in the current modeling and analysis effort for ASH flotation of fine coal. The first part is the modeling/analysis of dimensionless ratio of overflow opening area to underflow opening area, A*, and the dimensionless ratio of air flowrate to slurry flowrate, Q . The second part involves the modelling/analysis of all other variables in the system and an expert system for operation and control is introduced.

Jan 1, 1993

By Ishijima Y, Goto T

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic ar- ray. Location of microseismic events and in- tensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the inten- sity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increas- ing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are con- sidered. Observed and predicted displacement of the shaft axis agreed well.

Jan 1, 1992

By Wu Y, Qu Q

The Central Coal Mining Research Institute has developed the MAE acoustic emission monitoring system, the BD4-1 portable acoustic emission monitor and the MRB rock burst monitoring system. In the MAE system there is an IBM-PLAT, a receiver and 16 channels and the investigating range is 100 m. The main functions are detecting acoustic events from the working faces, periodically making statistics, prints, displays and storing of the results, and performing the off-line process such as drawing the curves of acoustic activity. The BD4-1 instrument has four channels, it works for more than 24 hours continuously, and keeps the data for more than 30 days after power tum-off. The BD4-1 is suited to the monitoring for a long or a short time as a fixed point where the system is invalid, especially to the monitoring of the acoustic activity promoted by the blasting. There is an IBM-PC/AT, a receiver and 16 channels spread 10 km in the system MRB. The system could on-line collect microseismic events throughout the whole mine, calculate the source location and the energy, and off-line draw the seismic activity draft of time-based or distribution in space. In practice, the forecasting is successful by using the acoustic emission and microseismic monitoring system and the portable instrument.

Jan 1, 1991

By Biao Q, Mizuta Y

Thermal constants such as thermal con- ductivity and thermal diffusivity of rock and coefficient of heat transfer of airway wall are the most important characteristic values which decide accuracy of prediction calcula- tion. However, quality of rock is not homoge- neous and water content in rock varies with location and so, a method for in-situ measure- ment of thermal constants must be taken in. The method developed by us is to measure in- situ rock temperatures at two different depths from airway wall. It is simple and we found its accuracy is good enough in the engineering Sense.

Jan 1, 1988

By Higuchi K, Sekimoto Y

In this report,the results of the large diameter drilling tests in coal seams assisted with water jet are described. The stress relief in coal seams by this new method is as effective as by the conventional method and the penetration speed by this method is 1.5 times as fast as by the other method. 1 Introduction The average mining depth of Japanese coal mines has already attained about 700m from the surface. Almost all coal mines are suffered from occurrence of coal and gas outbursts. To prevent outbursts, some countermeasures are taken generally. In particular, large diameter stress relief borings have been carried out quite often at Akabira coal mine located in the northern part of the Ishikari coal field in Hokkaido,JAPAN. These borings have had successful results but the drilling work of such large diameter

Jan 1, 1987

By Yamamoto Y, Ohyama H

In case of NATM, mechanical cutting is desirable in view of the original purpose of not spoiling natural ground. As typical tunnelling machines, there are two (2) kinds available: one is "Full Face Excavator" known as TBM (tunnel boring machine), and the other is "Roadheader" known as Part Face Excavator. By the use of the former, accurate profile cut is made possible, but there is a limit in the shape of a cutting section. By the use of the latter, cutting of various sections is made possible, but in order to cut a section economically and accurately, operators are required to have a high level of skill. In this text, we introduce Automatic Controlled Profile Cutting System (hereafter "ACPC" System) developed as a roadheader.

Jan 1, 1987

By Y Hansen, J Petrie

Life Cycle Assessment (LCA) is increasingly being used as a decision-support tool within mining and minerals processing and metals production. However, a number of initiatives have highlighted the current limitations of LCA to accurately reflect the environmental performance of minerals and metals. These programs include:the Mining, Minerals and Sustainable development project (Stewart, 2001); the United Nations Environment Programmme/Society for Environmental Toxicology and Chemistry (UNEP/SETAC) workshop on LCA and metals (NRCan, 2002); the UNEP SETAC Life Cycle Initiative; and the review of the existing ISO 14 040 set of environmental management standards. Together, these initiatives highlighted concerns relating to the ability of LCA to engage with and support metals recycling, to adequately reflect the impacts associated with products from a multi-product orebody, the ability to adequately reflect the toxicity potential of metals in the natural environment and the fact that resource depletion focuses on mining (and not consumption) as the depleting activity in the life cycle of a metal. Additional impact categories to be included in LCA were also suggested. In this paper we demonstrate how existing initiatives are addressing LCA limitations. Finally we present the state of the art in Life Cycle Impact Assessment (LCIA) for two impact categories:resource depletion; and impacted land footprint for solid wastes.

Jan 1, 2004

By D Baas, Y Atasoy

With increased pressure for companies to cut costs during design of new mineral processing plants, overall plant design has changed over the last decade with less design for feed blending and less installed surge capacity. This has changed the operability of new mineral processing plants, where disturbances due to variable ore types have resulted in the evolution of new control techniques. These techniques are necessary to maintain stability and optimise the performance of these new plants. This paper describes the benefit of applying these new control techniques in a new mineral processing plant in Australia utilising RockwellÆs ControlLogix system architecture.

Jan 1, 2008

By Hayashida O, Numata Y

Ultraviolet and infrared spectroscopic analyses and the extended lluckel molecular orbital method were applied to determine the electronic and binding states of 2-mercaptobenzothiazole and the adsorption system of 2-mercaptobenzothiazole on pyrite. 2-mercaptobenzothiazole exists rather in thione form than in thiol forru and the two adsorption peaks in solution were assigned to both 7t--?rt* transitions. 2-mercaptobenzothiazole chemically adsorbs on pyrite mainly due to forming the bond between iron (pyrite) and sulphur (2-mercaptobenzothiazole).

Jan 1, 1993

By T Medhurst

Recent developments in geophysical borehole log analysis using the Geophysical Strata Rating (GSR) are now routinely used in a number Australian coal mining operations. This allows development of 3D geotechnical strata characterisation models for a range of purposes. The availability of this data provides a means to identify relationships between ground conditions and ground behaviour. As a result, several new design methods have been developed to assist in the strata management process such as roof support, longwall shield design and shaft stability assessment. This paper outlines these methods and provides examples of their application. CITATION:Medhurst, T, 2018. Geotechnical strata characterisation using geophysics and its application for coal mine design, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 420–433 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Thompson P, Sharma Y

The paper describes the methodology and results from a study carried out by Telfer Gold Mine to optimise the materials and costs involved in construction of the pad for their dump leach operations. The investigation involved large-scale field testing of five different types of liner and a number of different cushion and drainage layer configurations. The aim was to identify the most cost effective construction methods to allow the final dump height to be increased from 45 in to 60 in without causing significant damage to the liner. The effects of dump height on permeability were also investigated. These methods are described and results presented. The findings indicated that modifications to the existing liner/cushion layer/drainage layer configuration used previously at Telfer would actually reduce overall construction costs rather than increase them despite an increase in overall dump height. Relative construction costs are presented.

Jan 1, 1994