Search Documents

By Zhang Qin

Dolomite is main impurity mineral in phosphate ores. In practice of phosphate ores production, the grade of concentrates is only containing P2O5 31-32%.In this study, even the increasing of floatation reagent consumption and decreasing of floatation recovery, economic performance is estimated high according to the decreasing of H2SO4 consumption in subsequent production of phosphate fertilizer and the increasing of products value. In floatation stage, influence factor include the synergism impacts of floatation collector, the stages, time, concentration of ore pulp, which were discussed respectively in this paper. Raw material is characterized by mineralogy, chemical analysis, the grain size analysis and milling test . The results show that the grade of concentration can reach to P2O5 36% by deeply de-magnesium oxide from phosphate ores by floatation , which yield a high added value.

Jan 1, 2009

By Nils Eivind Kamfjord, Roar Jensen, Ingeborg Solheim

"SINTEF has carried out several pilot scale silicon process experiments in the past, but always with an open off gas system. In order to test the possibilities in running a semi closed furnace operation, a new off gas hood has been designed and tested. The off gas hood is designed to collect all off gases to gain insight into the phase compositions in the off gas and at the same time have the opportunity to monitor and maintain the charging/stoking of the furnace. The furnace hood has regulation and control of the air inlet into the combustion zone in two different heights. The off gas temperature and composition was continuously monitored and analyzed during the experiment. In order to expand the knowledge on NOx- formation in silicon metal production, such information is vital.IntroductionBecause of the negative environmental impact, the attention towards all kinds of NOX emissions increases in Norway. The authorities’ demand towards better surveillance and control of emissions increases as well.Earlier and new industrial measurements in FeSi- and Si-metal furnaces reveal quite high NOX-emission. The measurements also show that the NOX formation (mainly as thermal NOX) is distinct connected to the formation of dust (SiO?SiO2) in the combustion chamber above the furnace surface, when the temperature is high and the access to N2/O2 is good. This means that stoking, charging and temperature straight above the furnace surface is important factors for the NOX formation."

Jan 1, 2012

By Norihiro Murayarna

Hydrothermal synthesis of K type zeolite was carried out by using coal fly ash as a raw material and KOH as an alkali source. The change in various physical properties of the obtained zeolite, such as the kind of zeolite crystal, cation exchange capacity, surface structure of zeolite and particle size distribution were investigated through the overall reaction of zeolitization. The reaction mechanism of K type zeolite from coal fly ash was investigated from these results in this study

Jan 1, 2002

By R. Padilla

The reaction of chalcopyrite with gaseous sulfur has been investigated in the range 350-450 °C in order to transform this mineral into a more acid soluble copper sulfide and insoluble iron sulfide. The results of thermodynamic analysis of this system as well as the X-ray diffraction analysis of the reaction products showed that in the temperature range 350 400°C the sulfidation reaction proceeded without formation of intermediate copper-iron sulfides according to: The effects of temperature and time on the conversion of chalcopyrite were studied. Conversion of chalcopyrite reached about 80% very rapidly with increase in temperature up to about 400°C. The recovery of copper from the sulfidized samples was determined by leaching in oxygenated 1.2M H2S04, 2M NaCI solution. Copper recoveries over 90 % were obtained from samples sulfidized for 30 min at temperatures lower than 400°C.

Jan 1, 2001

By J. D. Miller

Air-sparged hydrocyclone (ASH) flotation is a high-capacity flotation technology originally developed in the Department of Metallurgical Engineering at the University of Utah for processing mineral resources. However, the technology has been found to be useful in industrial waste processing, in the recycle of secondary resources, and in remediation of environmental problems. For example, areas in which the ASH technology is expected to have potential application include cleaning of waste coal fines, air stripping to remove volatile organics from drinking and process water, water disinfection by ozone or chlorine sparging, dispersed oil removal from water, and contaminated soil remediation. Recently, the ASH has been studied extensively for deinking flotation in the wastepaper recycling industry and has been shown to have excellent efficiency/capacity. In fact, a 20-million-dollar plant has been in operation since June 1992. The ASH technology can provide a specific capacity hundreds of times more than that which can be achieved with conventional flotation equipment and in certain instances is expected to provide superior separation efficiencies when compared to other technologies. The design and principles of ASH flotation are described. Experimental data for fine coal flotation, volatile organics stripping, and deinking flotation for paper recycle are presented and discussed. Finally, other potential areas of application for environmental technology are considered.

Jan 1, 1993

By Xinghui Meng

The leaching behavior of platinum powder in .iodide solutions under oxygen pressure in an autoclave was investigated. Ammonium salts were added to the leaching solution at neutral pH as a key lixiviant for platinum. The effect of temperature, partial pressure of oxygen, concentration of iodide and of arttmonium salts on the dissolution rate of platinum was examined. Under experimental conditions, the leaching behavior of platinum powder exhibited a complex reaction mechanism. A precipitate was found during the leaching process and was identified to be platinum ammine iodide, Pt(NH3hI4. The dissolution rate was controlled by a series of chemical reactions, the equilibrium concentration of the platinum ammine iodide being responsible for the ultimate limit to the recovery.

Jan 1, 1996

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting, lime roasting, is being tested fro retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04), oldhamite (CaS), calcium sulfite (CaS03), hematite (FenOs), magnetite (Fe304), and minor amoupts of pyrrhotite (Fel.,S) and pyrite. At 600°C, 650°C and 700°C the main constituents are anhydrite, oldhamite, and hematite. At 750°C, 800°C, and 850°C anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides, calcium sulfite, hematite, and minor oldhamite, magnetite, and pyrrhotite. At 650°C 700°C 750°C and 800°C, anhydrite, oldhamite, arsenic sulfides, and hematite are present. At 850°C, the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CLM) in the determination of the calcium-sulfur- oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RLM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1993

By L. J. Lutz

The U.S. Bureau of Mines has developed an electrorefining process to recover Ni, Co, Cr, and other metals from mixed and contaminated superalloy scrap. The superalloy scrap is cleaned then directly electrodeposited as a Ni -Co deposit. The process recovers approximately 90 pct of the Ni-Co available from the scrap as a 99t pct pure Ni-Co alloy. During electrorefining the electrolyte undergoes a purification process which results in Cr and other refractory metals reporting to the purification residue. Operating data is given for a 3-L compartmented electrolytic cell. Techniques for the removal of Fe, Cr, and trace impurities from the recycled electrolyte are outlined. The economics of a facility producing 15 mt/d of a Ni-Co alloy are also discussed.

Jan 1, 1993

By G. G. Richards

"The slag fuming process has operated for close to 70 years to recover zinc from lead blast furnace slag. The process is normally carried out through the batch treatment of slag by submerged injection of coal and air. Within the bath the coal acts as both a reductant, to reduce Zno to zinc vapour, and a fuel, to maintain bath temperature during the endothermic reduction process. The partition of coal between the slag, combustion and bypass is dependent on factors such as bath depth and injection pressure. The option of continuous fuming has been pursued at the D. Blagoev smelter in Bulgaria using heavy fuel oil as reductant/fuel. There has, however, been little attempt at commercial continuous fuming with coal. This paper presents an analysis of a coal-based continuous slag fuming furnace. The data on the Plovdiv fumer is used as a reference point. Critical design criteria for continuous fuming include the slag feed rate, degree of coal combustion and furnace size. Mathematical modelling analysis suggests that continuous fuming with coal can achieve respectable zinc/coal ratios.IntroductionThe slag fuming process was developed in the early part of this century to recover zinc from non-ferrous smelting slags [1-3]. The majority of installed furnaces were put in place to fume zinc from lead blast furnace slag on a batch basis. In most cases coal is used to effect reduction of zinc oxide, but one furnace uses natural gas [4] and, in a curious twist, a continuous fumer was developed based on fuel oil [5].Given the general nature of blast furnace lead smelting, it is not surprising that slag fuming has remained a batch process, in spite of the advantages that could be gained by moving to continuous fuming. Blast furnaces are usually operated as relatively independent units, and tapping has traditionally been done into ladles. The presence of a crane aisle makes direct coupling of the blast furnace to a slag fumer difficult, especially in a retrofit situation. Furthermore, steady-state blast furnace operation is not easy to achieve. The size of these furnaces and the nature of their feed make it difficult to guarantee constant operation."

Jan 1, 1996

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Jie Qiu, Yun Chen, Kai Tang

Isothermal reduction kinetics of CF2 by 30% CO and 70% N2 at 1123, 1173 and 1223 K was investigated by TGA in this study. The reduction rate analysis indicated that reduction of CF2 comprises three stages during the whole reduction process, Apparent activation energy of samples CF2 reduction is 34.37 kJ/mol. The ln-ln analysis implied the reduction of CF2 was expressed initially by a 2D subsequently by 3D shrinking layer reaction.

Mar 1, 2017

By W. L. Dalmijn

The processing of scrap and scrap cars starts with size reduction by a hammermill, or shredder. After the liberation the magnetic fraction is removed. The remaining non¬magnetic fraction mixed with other materials is screened and each fraction is processed separately. The increased use of plastic has a negative effect on the recovery of metals and waste production. At Huron Valley, Belleville Michigen, USA, the non-ferrous fraction from 5 million obsolete cars per year, containing 200,000 tons of non-ferrous metal, is processed. Aluminium Is recovered with a heavy medium separation process and concentrated with eddy current separators. The remaining heavy non-ferrous fraction is concentrated by a new combination of eddy current separation and image processing. After this separation process the zinc fraction is melted and refined and the copper, brass, stainless steel and other high-quality concentrates are sold to the secondary industries. The recycling of car scrap has become an important source of metals and materials for the secondary. materials processing industry.

Jan 1, 1995

By Steven R. Izatt

IBC Advanced Technologies, Inc. (IBC) has developed a mercury selective product, which can be used by sulfuric acid producers as either a polisher, or as the primary technology for mercury removal from sulfuric acid. The Molecular Recognition Technology (MRT) separations material selectively binds Hg2+, and to a lesser extent Hg+, out of concentrated sulfuric acid. Mercury output levels of less than 0.1 ppm can be attained by the MRT system. Pilot plant tests have been successfully conducted at base metal smelting operations. A large-scale commercial plant is due for commissioning in 2003. Results from these projects will be discussed.

Jan 1, 2003

By Kenneth P. Michalek, James E. Kelly, Jonathan A. Dantzig

"Many investigations have been reported regarding the simulation of continuous casting with emphasis on in-mold heat transfer. These analyses have been limited, however, because they require either estimation or measurement of the characteristic heat transfer between the ingot and the mold. In this paper, a self-consistent model 'is presented for calculating the heat transfer between a solidifying continuous casting and the mold, in the context of the continuous casting of steel. Using both thermal and stress analyses, the air gap formed during continuous casting is calculated and used to compute the heat transfer coefficients. Iteration between the thermal and stress analyses is used to determine a self-consistent solution. IntroductionThe continuous casting process for steel is illustrated schematically in Fig. 1. Molten steel is tapped into a tundish from which it flows at a controlled rate into the continuous casting mold. The initial shell of the casting forms in the mold by transfer of heat from the metal through the mold wall to the cooling water. The remainder of the casting is solidified by application of water sprays, and/or radiation cooling below the mold.Heat transfer in the mold portion of the process is important because it controls the formation of various defects which are deleterious to subsequent processing. Examples of defects formed in this region are surface irregularities, such as cold folding and oscillation marks, and more serious defects, such as longitudinal or transverse cracks. A more catastrophic problem which may occur is a breakout, in which the shell ruptures and molten steel is discharged in an uncontrolled way."

Jan 1, 1986

By J. A. Bustnes

The present work deals with kinetic studies of the reduction of molybdenum- and tungsten oxides by hydrogen. The experimental method used was therrnogravimetry under isothermal as well as non-isothermal conditions. The non-isothermal kinetics in the case of the reduction of MOO, to Moo2 has been modeled considering surface reaction as rate- controlling. In the case of the reduction of W02 to W a model was developed on the basis of the movement of the reaction front. The activation energies calculated on the basis of the models were in good agreement with those derived from isothermal experiments.

Jan 1, 1994

By Ray Y. Lin

This study explores the formation of sodium pyrosulfate in molten sodium sulfate resulting from dissolution of SO3 at temperatures between 1160 and 1250 K. Solubility of SO3 in Na2SO4 melts at temperatures between 1160 and 1250 K under gas mixtures of SO2, O2 and argon was investigated applying a thermogravemetric analysis (TGA) technique. The activity of Na2O in the melt was determined with a high temperature electrochemical cell (ECC). Results showed that the SO3 solubility in molten Na2SO4 increases with decreasing temperatures and increasing SO3 partial pressures. Enthalpy of SO3 dissolution in molten Na2SO4 was calculated to be -119 kJ/mol for infinite dilute solutions. Thermochemistry of Na2SO4-Na2S2O7 melts was analyzed based on information obtained from both TGA and ECC techniques. Detailed examinations of the earlier low temperature measurements in the Na2SO4-Na2S2O7 system along with data from this study reveal that the solution behavior between Na2SO4 and Na2S2O7 can be satisfactorily treated as regular with the interaction parameter, , being 2.7 kJ/mol. The phase diagram and the field of SO3 partial pressure has been generated with the thermodynamic calculation using a regular solution approach.

Jan 1, 2006

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Army Research Laboratory (ARL) has an interest in the recovery and processing of rare earth elements. At Montana Tech, elevated temperature chlorination of rare earth oxides is presently being investigated as a potential methods leading to the selective separation and recovery of rare earth elements from mineral ores and concentrates. After preliminary evaluation, ytterbium oxide was selected as a representative surrogate material for more extensive chlorination studies. Methods used to determine the conversion and recovery include X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis. These data have been used to establish and confirm process conditions that consistently yield high conversion efficiencies. Based on the promising results, further experimentation is underway to ascertain the metallurgical response of other rare earth oxides and carbonates to the roasting process. The end goal is to create a robust process for industrial application that has greater efficiency and reduced costs as compared to current practice.

Jan 1, 2015

By Tam Tran

Over the last decade, halide (chloride, bromide and iodide) systems have been evaluated as alternative lixiviants for the processing of gold to replace cyanidation which has been widely used in commercial practice. This paper first reviews the development of processes promoted by Kaljas Ltd / Lachlan Resources (Australia) and Great Lakes Corp (USA) using different bromide/bromine systems in the early 1990's. Several research groups subsequently evaluated the use of iodide/iodine and chloride/chlorine for gold extraction, showing similar characteristics of gold/silver dissolution and recovery. A critique is :given on the advantages and the ,shortfalls of halide systems as alternative lixiviants. The stability of gold? halide complexes is discussed, based on practical experience and thermodynamic modelling of their speciation, The iodide system provides the most stable gold / silver complex for easier handling. However, the cost of iodide inhibits its application for are processing. In this critique, emphasis is given on the cheapest system, which involves the use of chloride for leaching (in conjunction with an appropriate oxidant). However the chloride-base leachant has a major drawback which is related to the unstable nature of gold chloride in a reducing environment.

Jan 1, 1998

By Hector M. Henao

The FeOX-CaO-SiO2 base slag at intermediate oxygen partial pressures is very often used in non-ferrous smelting processes. This slag would also contain Al2O3 and MgO because these compounds are normal components in the ore and the refractory of a furnace. The objective of the present work is to determine the effect of Al2O3 or MgO addition on the liquidus temperatures of the plain FeOX-CaO-SiO2 slags in the atmosphere between intermediate pO2 of 10-6 and that of iron saturation at 1250 and 1300 °C. The experiments were carried out at given mass%CaO/(mass%CaO+mass%SiO2) ratios ranging from 0 to 1 and at spinel-tridimite double saturation. The experimental results show that the effect of Al2O3 or MgO addition on the plain FeOX-SiO2-CaO slag is not uniform and depends on the content of Al2O3 or MgO, the oxygen partial pressure and the mass% CaO/mass% SiO2 ratio. It is apparent that Al2O3 or MgO addition enlarges the spinel or wustite saturation area at almost all the oxygen partial pressures and temperatures of this research. The obtained phase diagrams will be useful in the metallurgical industry to assist in the selection of slag chemistry, operation condition and development of new processes.

Jan 1, 2006

By Xuyang Liu, Xuewei Lv, Chenguang Bai, Meilong Hu

"The electro-deoxidation process for ilmenite concentrate in molten salt was studied by cyclic voltammetry and AC impedance spectroscopy. The results from cyclic voltammetry are consistent with those of AC impedance spectroscopy. The results showed that the electro-deoxidation process for ilmenite concentrate consists of two steps. In the first step, Fe is reduced from the ilmenite concentrate. The second reaction is the decomposition of TiCh. CaTiCh is an intermediate product. At low voltage, the electrochemical reaction is the main step. With the increasing potential, the diffusion of ion is the main rate controlling step for the electro-deoxidation of FeTiO3.IntroductionTitania and titanium-rich products are mainly prepared from ilmenite concentrates (FeTi03), which contain about 40%-60% T1O2 after ore dressing and other physical or chemical processes [1]. At present, the main methods to prepare titania are the sulfuric acid process and the chloride process, but the sulfuric acid process consumes a large amount of sulfuric acid and the materials requirements for the chloride process are strict [2], Since the Electro-Deoxidization in Molten Salt (FFC) method was put forward in 2000, many researchers have successfully extracted the metal and alloys by this method, such as Ti, Cr, Tb, Si, Al-Si, TiV, FeTi, etc. [3-7], FeTi alloy is a typical hydrogen storage material, and because of its favorable properties, the preparation of FeTi alloy has become a hot research topic [7-9]. However, the mechanism of electro-deoxidization has not been studied thoroughly [10-11]. Therefore, in this study, the electro-deoxidation process for titanium concentrate was investigated by electrochemical methods, and the study makes a contribution to improving the current efficiency of the electrolysis."

Jan 1, 2012