Search Documents

By Shekhar Bhansali, Shyam Aravamudhan

"This paper reports on the design and simulation results of a silicon bulk-micromachined diaphragm-type piezoresistive pressure sensor capable of operating linearly over a wide dynamic range (0-1000 meters of water). The piezoresistor elements of the sensor are arranged in a wheat stone bridge configuration to achieve a higher output response. Simulation results (output voltage and sensitivity analysis) obtained using coupled MemPZR-MemMech module of the CoventorWare2003 Finite Element tool are presented. The effect of diaphragm size, diaphragm thickness and thickness of the piezos on output sensitivity were analyzed and optimized to get a linear response over the wide dynamic range.IntroductionThe physical and biological processes in the ocean are critically influenced by ocean parameters (pressure, salinity and temperature). Thus there is a need to develop inexpensive and reliable sensors to continuously measure large volumes of sea-space over long time spans. A key component in any such system will be a pressure/depth sensor. This sensor is routinely employed in marine applications such as wave and tide gauges, tsunami detection, platform leveling etc. More significantly, pressure measurement is needed for depth determination. Depth sensors are vital for remote operated vehicles (ROVs), profiling instruments and towed arrays.Several techniques have been routinely used in the past to measure pressure in the marine environment [1-3]. In general, the pressure sensor design is based on a flexible membrane as the spring element for the sensing pressure [4]. The deflection of the membrane, induced by the applied pressure, is converted into an electrical output through a component that is sensitive to diaphragm deflection (capacitive coupling) or associated stresses (piezoresistors, strain gauges). The temperature compensated pressure measurement can be readily converted to depth using"

Jan 1, 2004

By Joon H. Jang

At a selected pH, hydrothermal oxidation of chalcopyrite was carried out under controlled F+,, at elevated pressures and temperatures (172-200°C) by balancing the rate of oxygen injection against the rate of consumption. Chalcopyrite was converted to covellite (CuS) and digenite (CU1.8S) with rejection of iron and sulfur to the solution. Covellite forms in the first stage, followed by nucleation and growth of digenite in the second stage. The effects of rapid and slow injection of stoichiometric quantities of oxygen are compared. Both the covellite and digenite form a porous layer occupying the same volume as the original chalcopyrite grain. An electrochemical kinetic model is presented to correlate the observed results.

Jan 1, 1993

By Merete Tangstad, Fei Li

This paper studies the quartz and carbon black pellets at elevated temperature with varying temperature and gas atmosphere. High-purity quartz and commercial ultra-pure carbon black was mixed (carbon content wt.15%), and then pelletized into particles of 1-3mm in diameter. The stoichiometric analysis of the pellet during heating is studied in thermogravimetric analysis (TGA) furnace at different temperature in CO and Ar atmosphere. The microstructure, phase changes and element content of sample before/after heating is characterized by X-ray diffraction, scanning electron microscope, X-ray fluorescence and LECO analyzer. The reaction process can be divided into two stages. Higher temperature and argon atmosphere are the positive parameters for SiC formation.

Jan 1, 2016

By J. S. Pitsillos

A new furnace tapping technique involving the simulation of a control valve at the exit to a furnace is being investigated. The purpose of this new tapping technique is to regulate the flowrate of liquid furnace products( slags, metals and mattes). Numerical modelling and experimental work has been carried out on tapping of slags leaving a SIROSMELT reactor and the results found to be in good agreement. Numerical modelling has also enabled prediction of the important industrial conditions for the onset of blockage from the shape of the pressure versus flowrate curves. Slag launder experiments have been carried out and a one-dimensional heat transfer model was used to evaluate the effectiveness of launder covers and different coolants. From the experimental results and mathematical model some launder design guidelines such as inclination angle, covers and coolants have been developed.

Jan 1, 1991

By N. B. Gray, I. F. Taylor

"Gas injection to promote chemical reactions or mixing is a feature of many metallurgical processes. Often the aim of gas injection is to bring about a chemical reaction between the gas and liquid but most of the past physical and mathematical modelling work has ignored the influence of such reactions. In the work reported here, cold model studies have been conducted in which gas reacts with the liquid into which it was injected. The rate of liquid mixing has been measured as an indication of the mechanical energy transfer. It has been found that gas generated chemically within the liquid is significantly less effective at promoting mixing than the equivalent volume of inert gas. The relative ineffectiveness of chemically produced gas is thought to be due to smaller bubble sizes in comparison to the inert gas case. Small bubbles characteristic of chemically generated gas move with low slip velocities relative to the liquid and lead to different turbulence generation mechanisms.IntroductionIn processes such as steelmaking, copper conversion, bath smelting and ladle steel finishing gas is injected into liquid metal where it reacts chemically or simply serves as a source of agitation. An understanding of fluid flow phenomena in such situations is an essential pre-requisite to the calculation of process intensity and the optimisation of vessel productivity. Traditional physical cold modelling approaches to prediction of liquid flow in such situations are now often augmented by the techniques of computational fluid dynamics. Even with the availability of numerical modelling techniques cold physical models continue to have an important role for validation because it is generally difficult to obtain quantitative data from high temperature processes.Almost all previous cold modelling work has been based on the injection of an inert gas into water or some other non-reactive liquid. Such models do not include the significant increase in gas volume inherent in some processes. For example the oxidation of carbon in steelmaking leads to a twofold increase in molar gas flux through the reaction:"

Jan 1, 1996

By Larry M. Southwick

There is much ongoing work in research and development of new processes for the recovery and recycling of met.a.ls and other materials from various waste and scrap streams. Commercialization of such new technologies requires the bringing together and successful execution of a considerable effort involving a variety of activities. These include process conceptualization, research and development, detailed design and construction, and then plant startup and operation. Processes evolve through all of these steps by engineering due diligence, making objective and critical analyses of results, and troubleshooting processing steps to, hopefully, arrive at a sequence that has the best chance to succeed operationally and economically. After a summary review of the above steps, several processes will be described in more detail that provide mostly successful examples of the above procedures. Finally, some observations will be made on areas that will become critical in the near future to the success of new processes for wastes and residues.

Jan 1, 2000

By T. Wang, R. G. Reddy

"The corrosion of stainless steel SS316L in a low melting point novel LiNO3-NaNO3-KNO3- NaNO2 eutectic molten salt mixture was investigated at 695K. After long-term isothermal dipping corrosion experiments, the SS316L samples were analyzed using scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS) to determine the topography and corrosion products. Dense and protective lithium iron oxide scale formed on the surface and prevented the SS316L sample from further severe corrosion. Therefore, SS316L is considered to be suitable construction material for solar thermal energy storage materials containers.IntroductionMolten salt mixtures have been considered as potential candidates for thermal energy storage and heat transfer media in solar energy applications. To apply the molten salt in the energy transfer process, the standard pipes made of stainless steel must be utilized to carry the molten salt mixtures in parabolic trough system of solar power production. The pipes encounter continuous flow of hot and cold molten salt every day. Thus corrosion of stainless steel in molten salt mixtures becomes extremely essential for the long-term utilization of the thermal energy storage media. The corrosion of passivity materials inside high temperature molten salt systems have been studied which gives fundamental understanding of basic mechanism about the corrosion process [1-8].The corrosion behavior of Fe-Ni-Cr alloys in an equi-molar LiNO3–NaNO3–KNO3 mixture was studied [9]. According to the XRD analyses, the major phases in the oxide scales were identified as LiFeO2, Fe3O4 and Cr2O3. A HITEC® salt mixture (NaNO3–NaNO2–KNO3) was also tested as a corrosion medium for stainless steel [10] and the corrosion rate was found to be affected by the protective oxide layer. In most cases, the alloys having more than 10wt% chromium show high resistance to corrosion in molten salts."

Jan 1, 2014

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By W. G. Davenport

This chapter demonstrates how our matrices can be used for controlling a flash furnace. Specifically, it shows how we can determine the adjustments in industrial oxygen, air, oil and flux input rates that will; (a) correctly alter product temperatures and compositions to newly targeted values (b), maintain set-point product temperatures and compositions with varying feed compositions and feed rates. It also discusses corrective actions that might be taken when furnace temperature and matte grade unexpectedly change.

Jan 1, 2001

By J. P. Evans

The modem 'copper smelter today utilizes tonnage oxygen for smelting concentrates. ,generating a high strength S02 off-gas leaving the smelter vessel. This gas stream. which also contains any unreacted oxygen, plus CO2; N2 and H20. also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates, The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals, in the off-gas circuit. Depending on this history. the type and characteristics of the chemical and physical reactions which occur in the gas handling system 'can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries and design. on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data. several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By F. Ajersch, P: Tsantrizos, K: Shanker

"TiN films have been deposited on various substrates by a novel reactive plasma technology. In this process, a nitrogen source (NH3 or N2) and TiCl4 are reacted in the jet of a plasma torch, and are deposited onto a substrate forming TiN films at a high growth rate ( > 2µm/min). It was found that the process parameters strongly affect the microstructure, thickness, density, and growth rate of the TiN films. These parameters include source of nitrogen (NH3 or N2, N/Ti ratio, temperature of substrate, and spray distance. In general, it was found that thick and dense coatings were deposited when the N:Ti ratio was kept low, and the substrate temperature was high. Also, for the series of conditions investigated, NH3 was found to give much better results than N2•. The limitations and advantages of this technique are also discussed in this paper.IntroductionTiN is an extremely hard material and is used in many wear applications, particularly as a protective coating on cutting tools to extend their Iife(1.2). Owing to its excellent chemical stability, TiN is also frequently used as a diffusion barrier in the electronics industry for sub-micron Al/TiN/Si ohmic contact systems (3) or as a coating on high-temperature resistant alloys in gas turbine applications (4), based on its good resistance to oxidation. Other applications include decorative coatings in the jewelry industry, and specialized applications such as solar energy absorbers and transparent heat mirrors(5).TiN films can be deposited/formed using various techniques. The main techniques of deposition are CVD (Chemical Vapour Deposition) and PVD (Physical Vapour Deposition). Each of these techniques can have many variations in equipment characteristics, reactants as well as a range of process parameters (pressure and temperature). In the CVD process, TiN is generally deposited onto a heated substrate where a chemical reaction takes place. The reaction can be one of reduction(6) (e.g.: TiCI4 + 0.5N2 + 2H2 --> TiN + 4HCI), of thermal decomposition(7) (e.g. decomposition of titanium dialkylamide), or of displacement (e.g. TiCI4 + NH3 --> TiN + 3HCI + 0.5CI2)' The displacement and reduction reactions are the most common."

Jan 1, 1994

By B. C. Blakey

Unlike most hydrometallurgical slurries, those containing significant concentrations of goethite are typically highly viscous and shear-thinning, even at solid volume fractions below 5%. The viscosity may also depend upon time. These characteristics must be taken into consideration in slurry transport and heating. The technical literature is replete with apparent contradictions regarding the viscous behavior of these slurries, which may be due, in part, to variations in viscosity-measuring techniques. We present techniques that yield consistent results suitable for use in process design. A striking degree of time-dependent behavior is demonstrated for a laterite slurry. Reliable methods to design and analyze tubular transport and heating systems for time-independent slurries are summarized. Rules of thumb are then offered to account for the effects of time-dependency.

Jan 1, 2000

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By Z. M. Zheng

Cyclic voltammetry, potential step, and ac impedance techniques were applied to study the electrochemical reaction of arsenopyrite in chloride solutions. The relationship between anodic current density and time in potential step measurements indicates that the oxidation of arsenopyrite is irreversible. The results of the constant potential coulometry show that the stoichiometric factor of the total electron involved in the overall reaction is 14. It is proposed that the dissolution of arsenopyrite is retarded by coverage of sulfur produced in the reaction as an intermediate product. The measured results of ac impedance strongly support the proposition. The proposed reaction mechanism also explains satisfactorily the charging current density and Tafel slopes measured in potential step measurements.

Jan 1, 1995

By Terry Gerritsen

Electrode control systems regulate power by physically positioning electrodes. Due to the size and weight of the electrodes, this is a slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +I- 20% around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicans's laterite nickel furnace, yielding excellent results with a 3 to I reduction in power fluctuations. Keywords: SPLC, AC Power Supply, Electric Furnace

Jan 1, 2004

By Tim B. Vander Wood

Standard methods of determining clay mineral powder aspect ratios involve manual scanning electron microscopy analyses of shadowed particles in order to measure both platelet thickness and diameter. We present a method whereby the diameters of platelets are quickly determined by automated scanning electron microscopy and their images are recorded and digitally transferred to a transmission electron microscope equipped for parallel electron energy loss spectroscopy. Thickness' of platelets whose diameters are known from the previous analyses are determined by measurement of the ratio of scattered and unscattered electrons in the beam after it has been transmitted through the platelet.

Jan 1, 1995

By Carlos Maurício Fontes Vieira, Sergio Neves Monteiro, Diogo Neves Henriques

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850 to 1100oC. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at temperatures above 1000 ° C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antônio de Pádua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antônio de Pádua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption and low mechanical strength [3,4]. To avoid these problems, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2008

By Isrun Bohlinger

Resources recovery of brasses for semifinished products often results in the formation of hard spots impairing the quality of following abrasive and/or surface finishing processes. A short survey is given on the recycling processes, followed by the actual knowlegde of genesis, composition, and possibilities of avoidance of hard spots. Informations on genesis and composition of hard spots are completed by data from recent experiments.

Jan 1, 1998

By Stephanie Trant

Montana Tech has been engaged in fundamental research on the processing of critical materials for more than a decade. Efforts include examining novel reagents for the flotation of Rare Earth Minerals (REMs). For this paper, research results on a collector, salicyl hydroxamic acid (SHA), are presented. Various REMs were examined and include the rare earth oxides (REOs), carbonates (RECs), and phosphates (REPs) of a suite of Rare Earth Elements (REEs). Differences are attributed to solution and surface chemistry, coordination number, and ionic diameter. SHA adsorption follows an ion-exchange process that leads to chemisorbed and surface-precipitated states, depending mostly on pH. Many effects are directly attributed to lanthanide contraction. Results should also be applicable to other REM/collector systems and further suggest that REM flotation should consider dual collectors.