Search Documents

By K. Freytag

The extraction of lignite in open-cast mines has a severe impact on the landscape. Proper landscaping after the shut-down of the mines has always been the statutory responsibility of the mine operator. The large area of the land used for open-cast lignite mining requires special regional planning procedures well in advance of the permitting procedure stipulated in the mining law. The lignite plan determines, among other things, the objectives of land reclamation. These objectives will then be outlined in more detail in the mine operation plans and implemented accordingly. Apart from the actual mining laws and regulations, a large number of environmental laws also determine the process of land reclamation. The success achieved in the field of land reclamation in all mining regions during the recent decades has shown that the lignite mining industry creates new landscapes that do not leave any scars in the countryside and merge very well with it.

Jan 1, 2005

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011

The Anshan Iron and Steel Co. (AISC) broke its steelmaking design capacity in 1978, bringing its total production of steel products to 6.86 Mt. Located south of the industrial city of Shenyang, Liaoning Province, in northeastern China, it is by far China’s most important iron and steel complex, ranking twentieth among world centers. The complex represents a unique blend of old ecluipment and new ideas for increased production and improved products. Under a state plan, the Chinese hope to raise capacity to almost 15 Mt/a in the future. Originally started by the Japanese in the early 1920s, Anshan has had a rather turbulent 60-year history. It was disassembled by the Soviets after World War II, only to be reassembled by them in the 1950s. Production was also suppressed during the Cultural Revolution. Since the present-day organization, AISC, emerged, the center has experienced progressively improving conditions as well as increased production. Today, the center includes 10 blast furnaces, 24 open hearths, and two basic oxygen units, designed for 7 Mt/a ironmaking and 6.5 Mt/a steelmaking. In addition, it has six batteries of cokemaking facilities with combined 4.4-Mt/a capacity. Solid Iron Resources Anshan’s iron resources consist of a proven reserve base of over 7 Gt of 30~0 Fe, according to Kao Yang, president of the Anshan Iron Mining Co., a subsidiary of AI SC, Most of that, he continued, is amenable to surface mining. Five major mines located to the north and northeast of the city of Anshan are the principal iron ore producers. These mines trend in a somewhat circular manner and combined, represent an estimated 28.6 Ylt/a of ore capacity. In addition, some 2.2 Gt of magnesite, a necessary ingredient in steelmaking, are also part of the reserve base, according to Kao. Annual production is around .2 Mt/a of 47% magnesite, well over the steelmaking center’s annual requirements, Excess production is shipped to other steel-making centers. The largest of Anshau’s open-pit mines is the Chitashan operation with a design capacity of 8 Mt/a. Ore reserves here are well over a billion tons of 30% Fe. Earlier plans to expand production at this mine to 15 Mt/a, with the help of US Steel, have been temporarily shelved. The other mines in the district and their rated design capacity are: Kungchangling, 7 Mt/a; Donganshan, 6.4 Mt/a; Dakushan, 4.2 Mt/ti; and Yenchienshan, 3.0 Mt/a. The Kungchangling mine is the richest in terms of ore grade at 6076 Fe. Reserves are somewhat smaller at 100 Mt. The unit also operates a small shrinkage stoping operation. Ore grade at the other mines is usually 30-327. Fe. Llost mines operated at reduced capacity during 1979 owing to a natural gas shortage at the mills. The general

Jan 3, 1980

By William R. Yernberg

The current state of the copper industry was the topic of discussion at the Copper 99 — Cobre 99conference held Oct. 10 to 13, 1999, in Phoenix, AZ. More than 700 copper-industry engineers, executives, consultants, academics, vendors and other interested parties attended. This successful and well-organized conference was the fourth in a series of international conferences devoted to the mineral processing and extractive metallurgy of copper. The 1999 meeting marked the first time that the conference was held in the United States. The meeting was co-organized by the Minerals, Metals and Materials Society (TMS); the Chilean Institute of Mining Engineers (IIMCH) and the Metallurgical Society of the Canadian Institute of Mining, Metallurgy & Petroleum(CIM). The meeting was also sponsored by The Society for Mining, Metallurgy and Exploration Inc.

Jan 1, 2000

By Steve Kral

U.S. mines are among the most efficient, productive and safest in the world. Much of that efficiency is due to the high-technology equipment and processes available to the industry. The U.S. mining industry can produce more material now with fewer people than it could a few decades ago. And that material can be produced more safely. However, the workforce is growing older and fewer young people are filling the holes created by retirements. Even though mining is one of the highest paid occupations in the United States, young people believe they can find jobs that pay almost as well without the risks and the often remote locations associated with mines.

Jan 1, 2002

By S. E. Phillipson

The Mine Safety and Health Administration?s (MSHA) Roof Control Division (RCD) collects a variety of geological and engineering information pertaining to mining conditions in surface and underground mines throughout the United States. Recently, lineament analyses, trends of geologic structures, and inferred stress directions based on mapping at mines with problematic ground conditions, have been integrated into a GIS. The incorporation of different kinds of information into the same geographic coordinates and map projection, placed on digital geologic maps, allows site specific data to be evaluated in a regional geospatial context, identifying trends in the orientation of horizontal stress or patterns of structural geologic features. As more information is collected, the GIS will evolve as a tool for district- and basin-wide evaluations of controls on ground instability, and may evolve into a predictive tool for some kinds of geologic hazards. In addition to the geologic and geotechnical evaluations, the GIS also serves as a searchable database of previous mine investigations. The database can be searched for a variety of criteria, and the results displayed in real geographic coordinates to find the locations of previously visited mines or to evaluate mine fatality and injury data. This not only allows old reports to be found, but also places the information in a geospatial context with respect to neighboring mines or geographic areas. The GIS also has the capability to serve as a digital mine map repository, where maps can be stored in digital, georeferenced format for display in relation to each other and various themes of interest. This allows evaluation of multiple seam mining interactions and proximity to other mines, and on a national level could serve as an abandoned mine map database.

Jan 1, 2008

By M. Valdebenito, J. Rajala

An OCS Expert control system was implemented by Svedala Cisa at the Minera Maricunga Refugio Crush-Leach Operation near Copiapo, Chile. The purpose of the Expert system was to maximize production through the primary and secondary crushing circuits and help balance crusher usage between each stage to maximize total plant production. Interesting aspects of the control strategies are discussed. Benefits of the control were verified through a randomized On/Off test program. Tonnage increases ranged from 5% to approximately 20% at good confidence intervals. Benefits analysis results are discussed. The crushing plant at Refugio is very remote and is located at approximately 15,500 ft. This poses many challenges. The effect of altitude and remote location on plant operation are discussed.

Jan 1, 2002

By R. Thornton

Montana Tech is located in the historic mining town of Butte, MT and is adjacent to the Orphan Boy mine. This abandoned underground mine will be the heat source for a down-hole heat exchanger (DHE)/heat pump system. The mine was abandoned in the 1950?s and has since filled with water to within approximately 30 m of the surface. The shaft is composed of a 245 m vertical shaft connected with horizontal crosscut drifts at 60 m and 150 m below the water level that connect to a large stope with approximately 1250 million liters of water at a consistent 75-78°F temperature. The intent is to build this heating system to augment or fully heat a newly built 2,000 m2 building on the Montana Tech campus. As designed the system uses ?off-the-shelf? parts making the basic configuration straightforward with the exception of the DHE?s which need to be placed into the vertical shaft. Because there is little or no examples of placing the heat exchangers in a vertical shaft, the primary focus of this work was to model the heat exchanger placement and configuration in the vertical shaft such that thermal currents develop between the stope and vertical shaft in, via the horizontal crosscut drifts, in order to move the water and thereby provide the required energy. This study includes the modeling of water flow, temperature profiles, and the heat contribution from the surrounding rock walls.

Feb 27, 2013

By J. C. Willett, J. R. Sanfilipo, P. D. Warwick

The U.S. Geological Survey has conducted an assessment of the Nation’s coal deposits that potentially could be mined during the next 30 or more years. For the Gulf Coastal Plain region, the assessment includes reviews of the stratigraphy, coal quality and resources, and coalbed methane potential of the Cretaceous, Paleocene, and Eocene coal deposits in the region. The results of these efforts are a series of digital maps, text, and tables published in CD-ROM format. Although abundant coal resources are available in the Gulf Coast region, coal quality issues may limit large-scale development in the future. Additional data are required to better evaluate the coalbed methane resource potential for the Gulf Coast region.

Jan 1, 2001

By R. Steele

In addition to compliance with government emissions and reporting requirements, mining and mineral processing companies are increasing energy efficiency to reduce costs and become more competitive in the global marketplace. One of the major obstacles to identifying opportunities for increased energy efficiency is the lack of readily available data on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. As well as energy reduction, mining and mineral processing companies often struggle with the prediction of energy use, and are often penalized for under or over forecasting. Once again, it is the lack of timely information that makes this prediction difficult. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify energy reduction opportunities, reduce energy costs, and better predict energy use in a mining and mineral processing operation.

Jan 1, 2011

Coal bursts are one of the least understood yet the most critical hazards in underground coal mines. The ground motions induced by seismic events can trigger unstable failure of coal and rock mass and degrade the surroundings of an excavation. Therefore, the characteristics of ground motions should be fully investigated for an improved burst risk management. This paper analyzes ground motion features of a longwall panel from a typical underground burst-prone coal mine in China. The results showed that most of the ground motions on roadways were hardly initiate coal bursts due to insignificant energy input to the damage. The intensity of ground motions in near-field zone were nearly 20 times higher than those in far-field zone. The strongest vibration on roadway was induced by a coal burst with energy of 28,600 kJ, which can cause ground motion of 0.77 m/s and equivalent dynamic stress of 14.69 MPa. The findings of this paper can improve the assessment of seismic risks and its management.

Jan 7, 2020

By Guosheng Zhan

The Homestake Mine included the open cut and underground workings up to 2,484 m (8,150 ft) deep. The mine ceased mining activities in December 2001 after 125 years of operation. Pumping from the underground workings continued for 18 more months until June 10, 2003. Homestake had completed a comprehensive hydrologic evaluation on post-closure underground flooding prior to the shutdown of pumping. After closure, the mine was selected by the National Science Foundation as the site for the Deep Underground Science and Engineering Laboratory (DUSEL). An interim laboratory facility will be set at the 1478 m (4850 ft) Level. The final facility will be set at the 2256 m (7400 ft) Level or deeper. Pumping from the underground workings began on June 5, 2008 by the South Dakota Science and Technology Authority (SDSTA). During the period of June 2008 through March 2009, the pumping rate increased from 41 L/s (650 gpm) to 81 L/s (1,290 gpm) with an average rate of 60 L/s (950 gpm). As a result, the water level had been lowered more than 95 m (310 ft). It was found that the observed rebound and later decline to date is in close agreement with the model projections. Because of this, the authors of this paper reject claims of a lack of sufficient measurement devices in place and a lack of understanding of the hydrologic system at the Homestake Mine prior to shutdown of pumping in 2003 (Davis et al, 2009). Furthermore, it is believed that this validated model can serve as a useful tool for the SDSTA to manage future underground dewatering for the DUSEL operation. This paper evaluates the hydrologic conditions in the Homestake Mine area and projects the post-closure groundwater rebound and decline due to DUSEL pumping.

Jan 4, 2010

By Hyung-woo Kim, Sup Hong, Sung-Soo Kim, Chang-Ho Lee

A deep-seabed integrated mining system, which consists of four subsystems such as riser pipe, buffer, flexible riser, and tracked vehicles, is presented in Figure 1. In order to collect more manganese nodules, multiple tracked vehicle systems should be used in a deep-seabed integrated mining system.

Sep 1, 2014

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

Jan 1, 2005

By R. Hipsley, D. Arbonies, P. J. Dobak, M. Visher

The Storm deposit is a high grade breccia hosted “Carlin-type” gold deposit located at the north end of the Carlin Trend. Storm consists of 3 smaller deposits: 1) 49er Zone, 2) End Zone, 3) Discovery Zone. Structural intersections and favorable stratigraphy at the Paleozoic Popovich/Rodeo Creek formation and Bootstrap limestone formation contact are the primary known controls to gold mineralization at Storm. High grade silica-sulfide breccia occurs in the footwall of the north-south trending, dike filled, Dee fault. This mineralization cross-cuts silicified heterolithic breccia zones localized above the Bootstrap limestone where northwest, dike filled, reverse faults cut this structural-stratigraphic horizon. 40Ar/39Ar dates of 37.57+ 0.34 Ma (basalt dike) and 162 Ma (lamprophyre dike) have been obtained from dikes in the Dee pit which are locally mineralized by the same event as Storm. This paper will focus on the descriptive aspects of the Storm deposits.

Jan 1, 2001

By T. McKeon

Gravity separators are commonly used in multistage cleaning and scavenging circuits to improve the quality and/or recovery of the final concentrate. Unfortunately, studies suggest that many industrial plants are poorly designed in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiencies of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Jan 1, 2005

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Jan 1, 2006