Search Documents

By Braden Lusk

A typical rural house surrounded by a surface coal mine was instrumented in 2008. Information regarding ground vibration, airblast, and sounds inside the house was collected. Previous publications have included conclusions about this data with regard to blasting source (far-field or near-field) and results as to how the residents experience the blast were made. Several events were also recorded that were not related to blasting due to the nature of the trigger system. The trigger of the monitoring system was attached to one of the mid walls of the house, thus other normal daily events produced vibration levels significant enough to trigger the monitoring system.

Jan 1, 2011

By Alastair Torrance

The performance of commercial explosives is clearly influenced by the conditions under which they are used. Mining companies are supplied with Technical Data Sheets which provide details about explosive properties and its suitable application. These are generally produced using laboratory techniques which may not accurately reflect the quality and performance of the product in the field.

Jan 1, 2013

By Terry Matts, Bruce Ripley, Clark Fletcher, Paul Rapp, Stan Holtby, Jim Dent

The Stave Falls Project of BC Hydro, situated 65km east of Vancouver, BC, Canada, involved the construction of a new two-unit 9OMW hydro-electric facility to replace an existing powerhouse. The final phase of the intake excavation consisted of a plug blast to break the channel through into Stave Lake. The plug consisted of a rock and till wall topped with a fill cofferdam, about 51m wide and between 8 and 12m high. Total rock volume was approximately 2600m3, overlaid with about 4600m3 of till/fill. This paper describes the methodology and practical techniques used in planning and loading the blast, and the precautions taken to protect the new and existing structures and equipment. Blasting of the plug by the normal method using downholes would have required the placing of extra fill and much drilling through casing, so the contractor made the decision to drill horizontal holes from the dry, downstream side. Because of poor rock conditions, all 183 holes had to be drilled oversize at 3.5” dia. and fitted with 2.5” id. plastic pipes to keep them open. Hole lengths ranged from 2.5 to 18rn, with a pattern of 1.5m spacing and l.Om burden (with the holes slightly fanned vertically). Because of significant water exposure, a film-packaged emulsion explosive was used, placed using a pneumatic cartridge loader for maximum borehole compaction. The powder factor averaged 1.3kg/m3 (2.21bs/yd3, rock only). An initiation system of combination surface/downhole delay shocktube units was employed, with double and triple redundancy. The maximum number of holes firing in any 8ms window was limited to three (to minimize vibration), while the whole sequence was fully activated before the first hole fired. All shocktube connections were secured and covered over at the foot of the rockface before flooding the excavation downstream of the plug prior to the shot, To protect the powerhouse gates from hydraulic shock, all hole collars were grouted and an air curtain was provided. The blast was completely successful. A maximum vertical displacement of 6m was recorded, but no flyrock was evident. Readings for peak over-pressure and vibration were well below the allowed limits. Mucking proved to be easy, with fine fragmentation, full pull, and no tights.

Jan 1, 2000

By P. N. Worsey, M. Schmidt

Many advanced military systems and civilian power generation concepts postulate the availability of compact sources of electrical power capable of delivering gigawatts over microsecond time scales. For example, such a compact power source is essential for future practical pulsed high-powered microwave sources. An explosive-driven flux-compression power generator (EDPG) could fill this requirement. A basic strength of this concept capitalizes on the inherent high energy density storage capacity of modern chemical explosives. It relies on the physics of magnetic flux compression to convert that stored chemical energy into very large amounts of electrical power over short time scales. The generator also has the additional advantage of employing the same types of explosives that are already routinely used in conventional munitions. However, the self-destructive nature of this type of power generator places serious limitations on power pulse-lengths and ranges of applications. This paper describes how a multi-disciplinary team led by researchers from the University of Missouri-Rolla (UMR), Texas Tech University (TTU), and Texas A&M University was awarded a grant by the U.S. Air Force Office of Scientific Research to perform basic research to resolve several fundamental EDPG problem areas. Described are the utilization of UMR’s extensive explosives research expertise and facilities to investigate questions of energy conversion efficiency and the mechanics of energy production. Also, UMR explosives researchers will provide inputs to improved dynamic computer models of the complex, intertwined physics and chemistry operative in these devices. In addition to explosives expertise, UMR provides facilities for basic explosives material research, as well as the storage, machining, and formulation of explosives. UMR researchers are also using test facilities and data collection equipment at the Rock Mechanics and Explosives Research Center and at the UMR Experimental Mine to perform “proof of principle” and subscale tests of explosive-driven flux-compression power generator components. An integral part of the paper is a description of the development of an extreme intensity flash system by UMR and TTU to allow for the high-speed photography of EDPGs in operation. This multi disciplinary research program offers major advances regarding the size, weight, and electrical characteristics of compact EPDGs. Such breakthroughs could dramatically accelerate the practical realization of systems currently under study. Also, these power sources may have far reaching relevance to other Department of Defense and certain commercial compact power applications.

Jan 1, 2000

By Dan McCutchen, Oettmeier

Kelly bar drilling and blasting is unique to Florida, the' Bahamas and other marine limestone areas in the world where blast holes are required but will not remain open for the loading of explosives. This type of rock formation usually yields 1.5 tons of recoverable rock compared to 2.2 tons per cubic yard for competent limestone. The loss of .7 tons per cubic yard is due to voids and sand in the formation. These deposits all contain water to the top of the blast holes which are collared only a few ft. above the ground water level. The working pit is a water filled lake which is excavated from the bank by draglines. These drills have been used in Florida for many years to depths of 65 ft or less.

Jan 1, 1991

By Zheng Shuangying

The vibration effect of the buried oil pipeline caused by tunneling blasting affects the pipeline safe transportation, tunnel construction schedule and its construction cost. The dynamic response characteristic of the buried pipeline under blast loads is the foundation of designing blasting scheme as well as the prerequisite to pipeline safety. Taking the blasting engineering of Xiannvyan tunnel passing through a buried oil pipeline of the high-speed railway from Xi’an to Chengdu as the background, according to the space relation between tunnel and pipeline as well as the charge structure of V-cut blasthole, the 3D non-linear dynamic finite element model of tunnel-pipeline was established in the light of the equivalent explosive. The vibration response of the ground surface over pipeline resulting from V-cut blasting was simulated by LS-DYNA finite element program. Comparing with the measured vibration velocity waveforms in site, the accuracy and reliability of the numerical model are well verified. On the base of the simulation method, the coupling dynamic response characteristic between buried oil pipelines and soil was further studied and the Von-Mises stress distribution of pipeline wall was obtained. The safety of buried oil pipeline was quantitatively analyzed through the inside stress data of pipeline given by the simulation calculation above. The analytic results show that the maximum vertical vibration velocity of pipeline on the interface between pipeline and soil is 1.62~5.07 times as large as that of soil. When the buried pipeline is located over the tunnel and 13 m (42.6 ft) away from tunnel, the maximum vertical vibration velocity of ground surface caused by V-cut blasting with charge weight 17 kg (28.6 lb) is 3.17cm/s (1.25 in/s) and the vertical peak vibration velocity of pipeline top is about four times as the ground location directly above the pipeline. Meanwhile, the peak dynamic stress of the buried pipeline caused by blasting vibration is only 2.35% of the allowable stress of steel pipeline. The maximum superimposed stress of the blasting dynamic stress and the hoop stress produced by the pipeline internal pressure is 242.56 MPa (35 180.36), which implies that the buried oil pipeline is completely safe under the conditions of the given tunnel blasting scheme.

Jan 1, 2015

By Billy Rosseau, Mike Cammack, Richard O’Meara, Gustavo Azpilcueta

During the summer of 2014, the U.S. Army Corps of Engineers (USACE) sought proposals to vastly improve and expand the small boat harbor in Valdez, Alaska. It would be a multi-year project, and construction was scheduled to begin in the spring of 2015. One aspect of the project was the construction of a 3,100 feet (1000 m) rubble-mound breakwater to protect a mooring basin. An estimated 208,500 tons (190,000 t) of rock, ranging in size from 160 to 3500 lbs (73 – 1600 kg), were needed to build the breakwater. The Glacier Point Quarry was selected as the rock source due to its proximity to the project and the quality of the rock meeting all of the USACE rock standards.

Jan 1, 2017

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By David Hersey

The Paseo Bridge was located at the I-29/I-35/US-71 Missouri River Highway Crossing. It was built between 1952 and 1954 by Massman Construction Company. The 1,232 foot long, self-anchored suspension bridge was the longest of its type when built. On Jan. 22, 2003, a connector pin designed to allow the bridge to expand and contract during temperature cycles seized and caused a portion of the bridge deck to raise up and block traffic. This marked the beginning of the end for the old Paseo Bridge.

Jan 1, 2013

By Corry Goumans, Ron J. Elliot

This paper discusses the challenges encountered in drilling and blasting of a small diameter shaft underneath a parking garage in historic Gastown, Vancouver, BC. This project involved drilling in a restricted headroom area, blasting in a confined space environment, and excavating using a novel vacuum technique. The 1.2m x 1.2 m x 8.5m deep shaft was required for installation of a hydraulic piston for a show lift. The project called for very accurate drilling through inter-bedded sandstone and siltstone within the water table. Development of a unique blast design was required for blast vibration control on a historic structure located just 15.8 meters away. The shaft was successfully completed without damage to any of the surrounding structures.

Jan 1, 2004

By Andreas Bienz

The safety of persons from accidental explosions and fires during manufacture, storage, transport etc. of explosives, pyrotechnics, propellants, firework and ammunition is most commonly assessed according to prescriptive rule-based approach: Safety is given when all requirements which are listed in numerous regulations and directives (such as e.g. safety distances, limited quantities, protective installations etc.) are complied with. Such a deterministic prescriptive rule-based approach is quite easy to apply but has got disadvantages, however: The actual state of safety in a specific case is not explicitly and quantitatively expressed, and it is not distinguished between the endangered individuals and the whole group. As a result, the effects of the safety measures cannot be measured. This is why uneconomical and in the worst case useless safety precautions cannot be avoided. In addition, waivers are difficult to negotiate, meaningful and sound arguments for pro and con being lacking.

Jan 1, 2007

By M. Oguz Ozkazanc, Gulsev Uyar Aldas

Because of its safety, being easy to handle, relatively inexpensive and containing a lot of energy, ANFO is the most popular and widely used explosive in Turkey as well as other countries in the world. According to change dated May 14th 1999 on the regulation 87/12028 related with explosives, blasters are not allowed to mix ammonium nitrate and fuel oil in the tield to make ANFO. Instead of this, they have been forced to use the ready ANFO prepared by explosive producer firms. As a result of this obligation, the use of technical nitrate for agricultural purpose and mixing AN and fuel oil in unsuitable conditions have been prevented. Indeed, wrong mixture means waste of energy and money.

Jan 1, 2001

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

Test blasting was carried out to study the flying characteristics of rock mass caused in bench blasting. The quantity of explosives was increased from 7.6kg to 9.1kg and the Minimum burden was changed from 131mm to 451mm. The effect of condition for the characteristics of fly rock were considered. The fly rock was observed using the high-speed camera and video to study the flying characteristics of the rock mass caused in the bench blasting. Numerical simulation of fly rock was carried out using DDA (Discontinuous Deformation Analysis) method. It was clear that the DDA method can be applied in the simulation of fly rock caused in bench blasting.

Jan 1, 1997

By A. Andrades, E. Arias, Y. Pizarro, J. Alarcón

Division Ministro Hales - Codelco (DMH) is located at 2600 meters above sea level, 10 km north of the city of Calama, Antofagasta region, Chile. In operation since 2010, it corresponds to a porphyry copper deposit that is exploited by the open pit mining method. The ore is mainly composed of sulfides, which is concentrated by comminution processes such as crushing, SAG milling and ball milling to liberate the mineral particles, and then separated from the waste (concentrate) in flotation stages, including a concentrate regrinding stage. Reports from the DMH processing plant area have identified a decrease in fine copper recovery, with the first hypothesis being the high percentage of ultrafine particles (% <45µm) in the flotation feed. Due to the above, DMH & Orica decided to carry out activities to identify the controllable variables that can impact the generation of low size particles in ore and adjust them to reduce the percentage of fine material generation, with special focus on the Drilling and Blasting processes. Based on the data provided by DMH, we evaluated what could be integrated to make an analysis. The different attributes associated with the ore and their effect on copper recovery were evaluated. In parallel, at the mine, a fragmentation measurement campaign was carried out at the loading faces and granulometric analysis of the drill cuttings. Once the correlations between the attributes and copper recovery were identified, hypotheses were established and reviewed with the Drilling & Blasting, Geotechnical, Geology and Process Plant areas. With the validations of the hypotheses and the results of the in-mine (cutting) measurements, we proceeded to review the criteria for the classification of Blastable Geotechnical Units and their associated D&B designs. Using software and the Crush Zone Model (CZM) tool, which considers rock and rock mass parameters, scenarios for various D&B design proposals were simulated with the objective of reducing the generation of ultrafine particles from the blasting process. Next steps include trial blasting with the D&B design recommendations, which will require follow-up to the flotation process to identify the impact on the reduction of ultrafine material from blasting.

Jan 1, 2024

By Q Liu, P D. Katsabanis

The energy output of crushed AN/FO, crushed AN/FO mixed with Aluminum (5%, 6.4% and 9.4% A1 by mass) and a commercial emulsion explosive has been measured using a detonation calorimeter. The charges had a diameter of 10 mm and were heavily confined by a 11 mm thick copper shell. In order to achieve stable detonation glass microballoons were used in the explosives so that the density of the AN/FO charges would be around 1.1 g/cc. The charges were detonated in vacuum and the detonation products were analyzed using gas chromatography. It was found that energy values were very close to calculated values obtained by ideal detonation codes.

Jan 1, 1993

By Don Larson, Gordon Coleman

The United States Department of Energy, through its contractor Lawrence Livermore National Laboratory, has entered into a contract with Alpha-IRECO, Inc. for the emplacement of approximately 2.9 million pounds of a 50% RX-MD emulsion 50% ANFO blend into an underground chamber for initiation to produce the 12 trillion caloric equivalent of 1,000 metric tons of TNT. The detonation will be closely monitored to determine the characteristics of a large chemical explosion for comparison with data collected from previous like-sized nuclear events in the same location. This data will be shared with former Soviet block countries to facilitate enforcement of the various non-proliferation treaties currently being negotiated between the countries.

Jan 1, 1994

By Neal Lee

Often the effects of wet boreholes are not taken into consideration when designing a blasting program to exhibit a certain amount of explosive energy per unit of rock such as design by powder factor, expressed in lbs./bcy (pounds explosives per bank cubic yard) or kg/bcm (kilograms per cubic meter), often the effects of wet holes are not considered. This paper examines different methods of loading wet holes and the effects they have on actual explosive quantities/unit of rock. In particular, we are looking at the amount of water trapped within the explosive column (bulk loading from the collar), or the annular space left void of explosives product around and between cartridges (wet-bags) with many of the current wet hole loading methods in use. We will focus on the effect this has on actual powder factor relative to “as designed” dry hole loading values, as well as the effect on performance of the explosives.

Jan 1, 2011

By Jan Westberg, Roger Holmberg, Bernt Larsson

Over the last couple of decades there has been an increased demand from the market for precision detonators, partly because of a need for better blasting results and partly because of a need for better vibration control. Today's detonators have a pyrotechnical delay element which gives a relatively high time scatter, increasing with the length of the delay time.

Jan 1, 1988

By Ph. D. Favreau, Favreau Patrice B. Eng, R. F.

Geology is important in mining by helping to identify the rocks which contain sufficient valuable ore to justify their excavation. Geologists give a geological name to each rock type, so geology is a player in blasting; when a blaster has successfully blasted rock of a given geological name at a former site, and he later has to blast rock at another site whose rock has the same geological name, then his first trial often is the same method as he used at the former site, since the geological name of the rock is the same

Jan 1, 2019

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002