Search Documents

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

By Alexander E. Sobolev

The kinetics of oxidative dissolution of lead sulfide in solutions of nitric acid and sodium hypochlorite was studied using the rotating disk method and the factor experiment design. The dependences of the PbS dissolution rate on concentration of oxidant (HNO3 or NaOCl), temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific dissolution rate at any combination of values of the influencing factors were obtained. As a result of the complex analysis of kinetic parameters, the modes of the each process proceeding were established, their macromechanisms were determined, and the limiting stages of the oxidative dissolution processes were revealed. The dissolution kinetics of lead sulfide in solutions of nitric acid was found to have several regimes. At HNO3 concentrations below 0.5 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled. It is caused by low oxidative activity of HNO3 and considerable diffusional diffuculties at this acid concentration range. At the nitric acid concentrations more than 0.5 mol/L and less than 6.0 mol/L, the process was found to be kinetically controlled. The limiting stage of the interaction is the surface chemical reaction. The observed relatively high order of the dissolution rate with respect to the concentration of HNO3 was explained by the autocatalytic action of the acid reduction products. At nitric acid concentrations exceeding 6 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled, and the dissolution rate sharply decreased that was explained by a decrease in the solubility of reaction products. When lead sulfide is dissolved in sodium hypochlorite solutions, at first time the amount of PbS transferred into solution remains close to zero. Gradually, as time goes, this amount begins to increase sharply. The dissolution rate rises and reaches the maximum value, further remaining constant. At the steady-state regime, the dissolution rate is independent of the duration of interaction and disk rotation frequency. The process was found to be kinetically controlled. The limiting stage is likely to be chemical reaction on the surface of solid lead sulfide. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulfides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of lead-bearing ores and concentrates. Keywords: lead sulfide, nitric acid, sodium hypochlorite, hydrochemical oxidation, dissolution kinetics

Sep 1, 2012

By J. Jávor

The response of the air/water interfaces to deformation in presence of surfactants is affected by the adsorption/desorption rate, re-orientation and exchange rate of surfactant. These surface properties can be observed using equilibrium and dynamic surface tension and surface elasticity measurements. However, the effect of these parameters on bubble size in dynamic conditions has not been studied due to the difficulty in capturing freshly formed bubbles in dynamic conditions. The paper presents a new experimental set-up designed and built at the Aalto University, called Shear Force Observation Chamber(SOC). The setupallows the monitoring and analysisof freshly formed air/liquid interfaces in dynamic conditions and facilitates the study of the effect of dynamic surface tension and surface elasticityon freshly formed air bubblesin presence of surfactants. The method helps to establish correlation between bubble size and dynamic interfacial properties and bubble-bubble interaction in turbulent flow. Dowfroth 200, Nasfroth 240 and Dowfroth 250 commercial flotation frothers were tested in this study. The results show a marked difference between results obtained in dynamic conditions compared to the static conditions. The results are presented and the reasons and implication to flotation modelling are discussed in the paper. Keywords: shear force observation chamber, flotation frothers, flotation bubbles, critical coalescence concentration

Sep 1, 2012

By Chao Li, Kym Runge, Saeed Farrokhpay, Dee Bradshaw

"It is well known that froth phase has a controlling influence on the overall flotation performance. Froth recovery is expected to be affected by froth transportation behaviour. The latter has been represented by different volume balance and energy balance based models. In froth transportation models based on a volume balance, the froth phase is divided into different zones. The total froth residence time is the sum of the time spent in each zone and is dependent on the cell geometry, bubble burst rate and the position that bubbles enter into the froth phase. Alternatively, the froth transportation model based on an energy balance treats the froth phase as a block. In this model, froth height above the concentrate lip is being predicted by minimising the energy of the system which is dependent on the froth geometry, froth stability and froth rheology. The froth height can be used to calculate the froth efficiency of delivering mineralized bubbles from the pulp to the concentrate lip. This paper critically analyses the current models of froth transportation in flotation, and examines the limitations of these models. The importance of froth rheology, which is the resistance to the froth flow towards the discharging weir, in determining froth transportation, is also highlighted."

Jan 1, 2014

By C. Y. Sun

Flotation of chalcopyrite and unactivated malachite with xanthates (ethylxanthate, butylxanthate, octylxanthate and dodecylxanthate) is studied in this paper. Minerals interacted with xanthates are detected by FTIR, and simulated by molecular mechanics. It shows that chalcopyrite can be floated with 4 kinds of xanthates, and unactivated malachite can?t be floated with ethylxanthate but can be floated directly with later 3 kinds of xanthates while characteristic absorption peaks of those four kinds of xanthates are all detected by FTIR on chalcopyrite and malachite surface. After simulating the interaction between xanthate and mineral, it shows that H2O and OH-can interact with chalcopyrite and malachite, and their interaction energy may be so called energy bulwark which must be overcome by collector when collector interacts on minerals; the two sulfur atoms in xanthate group interact with copper and neighbor iron atoms on chalcopyrite. It also shows that molecular mechanics results with logP of collectors can interpret the mechanism of xanthate-mineral on atom scale.

Jan 1, 2014

By Yuriy V. Gulyaev, Galina V. Sedelnikova, Valeriy D. Lunin, Valentin A. Chanturiya, Igor J. Bunin

"Probable mechanisms of disintegration of mineral particles in gold-containing sulphides and benefication products exposed to high-power electromagnetic pulses are discussed. Experimental data are presented to confirm the formation of breakdown channels and selective disintegration of mineral complexes as a result of pulse irradiation, which makes for efficient access of lixiviant solutions to precious metal grains and enhanced precious metal recovery into lixivia during leaching. Experiments with different gold-containing products revealed a synergetic effect of high-power electromagnetic pulses with widely varying parameters and moisture in mineral pores on breaking-up and gold extraction processes for various resistant goldcontaining mineral products.Several series of tests performed in IPKON RAS, IRE RAS and TsNIGRI yielded an absolute gain in precious metal recovery, up to 30-80 % for gold and 20-47 % for silver, with resultant gold recovery as high as 90 %. An essentially new, environmentally safe and energy-saving breaking-up technology has been developed for resistant gold-containing products. This new method would shorten the way from raw minerals to final products and help significantly reduce the cost of these products as it obviates the necessity for using the expensive procedures of energy-intensive and environmentally hazardous oxidative roasting and autoclave breaking-up for ore concentrates."

Jan 1, 2003

By Di Liu, Yongjun Peng

"It was identified that clay minerals adversely affect fine coal flotation through slime coatings. In the study, it was interesting to find that an anionic polymer dispersant, lignosulfonate, successfully mitigated the negative effect of clay minerals in coal flotation using fresh water, but in saline water, it exacerbated coal flotation.In order to understand the mechanisms underpinning the different behaviour of lignosulfonate in coal flotation using fresh and saline water, the adsorption isotherm, and dynamic light scattering (DLS) measurements were conducted in this study. While DLS monitored the molecular conformation change (swelling or shrinking) of the polymer in fresh and saline water, adsorption isotherms enabled polymer adsorbed amount on clay and coal mineral surfaces to be determined. It was found that lignosulfonate adsorbed on the coal and clay mineral surfaces providing effective electrostatic repulsions and resulting in a mitigation of clay minerals from coal surfaces in deionised water. In the presence of saline water, however, polymer molecular conformation changed. Polymer molecules were compressed and adsorbed in form of aggregates. The adsorption amount of lignosulfonate on clay minerals increased in saline water. A low dosage of lignosulfonate could not provide sufficient electrosteric repulsion to disperse clay minerals. Moreover, the high adsorption amount of the polymer on coal and clay surfaces led to a more hydrophilic coal surface, and coal flotation was therefore depressed in saline water. This study provides a new insight into understanding the role of anionic polymeric dispersants in mineral flotation using different quality water."

Jan 1, 2014

By M. Canbazoglu

In this study, optimum sulphuric acid leaching parameters of zinc and other valuable metals from two different waelz clinker samples were researched. Origins of the samples are electric arc furnace dust and original non-sulphite zinc ore waelz clinkers. The main zinc mineral determined as zincite in these samples. Collective dissolution of zinc and other valuable metals in waelz clinkers can easily achieved by sulphuric acid leaching of them. 96% of zinc can be dissolved at 80 ºC, 60 g/L sulphuric acid concentration, 60 min. leaching time and 1/5 solid/liquid ratio. Almost 90% of Cd, Cu and Co in clinker dissolved at these conditions while dissolution of Fe was almost 20%. The consumed acid amount for dissolved per ton of zinc is approximately 1.7 tons at these conditions.

Jan 1, 2014

By Masakazu Niinae, Kenji Aoki

"Electrokinetic soil remediation by electroosmosis and ionic migration is restricted to soluble substances. At a higher pH, the soil particles sorb more heavy metals than at a lower pH and the precipitation of heavy metals are promoted. Both mechanisms make heavy metals immobile, rendering cleanup more difficult and electrokinetic extraction inefficient.In this study, the effectiveness of introducing a complexing agent to enhance the removal of cadmium from kaolinite in the region of neutral pH by ionic migration is examined. The complexing agent selected was ethylenediaminetetraacetic acid (EDTA). The investigation was carried out in a laboratory-scale column containing kaolinite contaminated with cadmium. As the results of the study, cadmium migrates toward the anode without accumulation of cadmium and is successfully removed at the anode reservoir."

Jan 1, 2003

By A. R. Videla, P. R. Brito-Parada, I. Mackay

"Linking results from laboratory scale experiments to industrial flotation behaviour is challenging. Typically, such experiments involve batch tests in which the system does not operate at steady-state, making it difficult to infer the effects that operating conditions have on flotation performance. In order to overcome this limitation a 4-litre recirculating tank was previously developed at Imperial College London. This tank is capable of reaching, and operating at, steady-state by recycling overflowing concentrate back into the feed. As well as instruments to control operating conditions, it is fitted with a system of sensors that allow the surface of the froth to be dynamically monitored. From this information, it is possible to measure the air recovery—a proxy for froth stability. Thus, this bench-scale tank can be used to understand the effect of differing operating conditions on flotation performance at steady state. However, so far, this cell has only been used to investigate idealised systems with only one or two species.Reprocessing of tailings dams is not only environmentally desirable but also increasingly economically feasible due to the declining head grades of primary deposits. There is also the added benefit of no further milling being required prior to flotation. However, the effects of fine and ultrafine particles on froth stability are not yet fully understood. In this work, the bench-scale continuous tank has been used for the first time to determine the flotation response of a complex feed, consisting of samples from a copper tailings dam, to changes in operating conditions. It was shown that the froth stability in the system is comparable to that of previous work and industrial tests, with a peak in air recovery being found at a superficial gas velocity of 1.13 cm/s. There is scope to optimize the froth stability of tailings flotation for enhanced metallurgical performance."

Jan 1, 2018

By N. Naude, W. P. Roux

"Traditionally minerals processing equipment, such as jigs, are studied by characterising the feed and products from these processes. With this approach important details on the mechanisms of a process can be overlooked since assumptions have to be made on the internal operations of the equipment. Positron Emission Particle Tracking (PEPT) is a non-invasive technique that can be used to track a particle’s movement inside a closed vessel. PEPT makes it possible to observe the inner workings of a process, providing new information that was unattainable only a few years ago. Jigging has long been considered as one of the most difficult mineral processing techniques to model, due to the complexity of the mechanisms contributing to the separation of minerals during the jigging process. In this investigation PEPT was used to study the particle flow inside a laboratory batch jig. The aim was to determine if the particle trajectories could provide new insight into the jigging and its mechanisms. Three dimensional particle trajectories were observed with spatial and temporal resolution high enough to see details of the individual pulses during jigging. It was found that the pulse height is very dependent on the position in the jig bed. The vertical component from the trajectories showed the rate at which particles move through the jig bed (stratification rate) and it was seen that the density of a particle affects the stratification rate more that the particle’s size and that the shape in the range that was tested had little to no influence. Other phenomena such as a circular flow pattern was observed inside the jig and it was found that smaller lower density particles are affected by this circular flow pattern which tend to disperse these particles throughout the jig bed. Visualising the flow inside a jig by means of PEPT has shown to be instrumental in the deeper understanding of the process."

Jan 1, 2018

By C. P. Lowes

"The REFLUX™ Classifier (RC™) consists of a fluidized bed housing, with a system of parallel inclined channels above. This system performs a simultaneous gravity separation and desliming of the feed material, utilising the inclined channels in order to retain the relatively fine dense particles. These particles promote the formation of an autogenous dense medium within the fluidized bed. Relatively large, low density particles are displaced from the fluidized bed and conveyed upwards through the inclined channels reporting to the overflow with other finer particles. Given the hydrodynamic role of both the particle size and density in determining the particle transport through a water based suspension, all gravity separators operate over a limited size range. In the case of the REFLUX™ Classifier, efficient separations can be produced across a very broad size range, from nearly 10 mm down to 10 m, however, for a given application the size range is much more limited. This study was concerned with the processing of dense minerals over a broad size range, and the need for multistage processing. Here the overflow from the first stage cascades to the second stage, incorporating coarse gangue rejection. This approach is shown to deliver remarkably high grades and recovery.INTRODUCTION The performance of the REFLUXTM Classifier (RC™) in beneficiating fine coal is well documented (Galvin, 2012). Although the technology can be applied to relatively fine particles below 0.1 mm, or coarser particles below 2.0 mm or even 8.0 mm (Galvin et al., 2010), in each case the technology is applicable to limited particle size ranges. In coal preparation, the most common size range is 0.25 to 2.0 mm, covering an eight-fold range in the particle diameter. Coal has a relatively low density, typically below 1600 kg/m3, with a significant portion below 1400 kg/m3. In water, the buoyant density difference (~ 400 kg/m3) is therefore low compared to that of gangue minerals (1600 kg/m3) by a factor of 4, enhancing the potential for separation. Thus, in coal preparation, the technology can be applied over a commensurately broader size range, typically up to eight-fold."

Jan 1, 2018

By P. Harris, D Bradshaw

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003

By Silvia França, Hudson Couto, Renata Barbosa

"The flotation process, largely used for mineral concentration processes, which is based on air bubble adhesion to the dispersed solid phase, is also being used for wastewater treatment purposes. Dissolved air flotation (DAF) is based on the separation of the solid-liquid phases with the aid of small air bubbles (10-100 µm), with high values of interfacial contact area, improving the process efficiency. In the process, the air bubbles and particles or flocs form aggregates, which rise to the surface of the flotation cell to be collected. The advantage of producing small bubbles is directly related to the fact that smaller bubbles result in greater bubble-particle interaction. Wastewater produced in alumina refinery - from the red mud filtration step - has a red colored aspect due to the presence of very fine particles of red mud and also dissolved matter that still remain in the filtrate. This wastewater might be treated, aiming to reuse the water in the refinery or discharge it properly in the environment. The aim of this study was to evaluate the DAF process efficiency for the treatment of red mud wastewater in order to decrease suspended particles and dissolved solids contents, in addition to mitigate the high causticity of this wastewater. The process efficiency was evaluated by comparing turbidity removal and total solids concentration in the treated wastewater to the feed. The influence of important variables of the DAF process as type and concentration of coagulant and flocculant were evaluated. It was possible to obtain good turbidity removal efficiencies (up to 90%) using low concentrations of coagulant (50 mg/L) and flocculant (0.5 -1.0 mg/L). In addition, for most of the experiments, the specification for effluent diposal, according to the Brazilian environmental regulation 430 (Conama, 2011): pH range 5 to 9 and turbidity < 40 NTU, was attained. These results emphasize the possibility of using the DAF as an alternative technique to settling and filtration process, that are traditionally used, for treating wastewater from the alumina industry, allowing the reuse of water in the plant or adequate discharge with less environmental impact."

Jan 1, 2014

By Venkataramana Runkana, Shantanu Maheshwari

As the world reserves of high quality ores are getting depleted at a rate higher than ever, the liberation of valuable minerals from low grade ores is becoming more and more relevant and imperative. But, liberation of minerals from low grade ores requires grinding of ore to extremely fine sizes. High energy milling in a planetary ball mill is one such option where one can produce particles in the nano-meter range. Although planetary mill is employed extensively for ultrafine grinding, dynamics of grinding inside the mill is not fully understood because of the dependency of grinding kinetics on many interconnected phenomena like collisions between media, particles and wall, time dependent rheology, adsorption and desorption of dispersant, abrasion of media, agglomeration of particles, etc. It was well articulated in literature that media motion and number of media collisions have strong effect on grinding kinetics and final product size distribution. Simulations were carried out using the discrete element method (DEM) to compare the performance of a planetary mill with a ball mill, with and without lifters, in terms of impact energy and number of collisions and it was found that number of collisions is considerably high in the planetary mill. The high number of collisions might be the reason for production of ultrafine particles in the planetary mill. We have also fitted a population balance model (PBM) to experimental data from a laboratory scale planetary mill for prediction of particle size distribution. Unlike previous models, we have incorporated functional forms for the selection function and the breakage distribution function so that the number of parameters in the PBM is just five. The predicted product particle size distributions at different grinding times are in reasonably good agreement with experimental data.

Jan 1, 2014

By Kaiwen Liu

Activated carbon is widely used in the removal of organic and/or inorganic contaminants from waste water due to its high surface area, porous structure, and specific surface reactivity. However, in practical applications, it is difficult to recover the activated carbon completely by screening or classification. In this project,we prepared a magnetic form of activated carbon (magnetic activated carbon or M-AC) by precipitation of iron oxides on the surface of activated carbon. The M-AC can be easily separated from effluents by applying an external magnetic field, thus it can be recycled and regenerated for reuse. M-AC was characterized by X-ray diffraction (XRD), specific surface area measurement, and scanning electron microscope (SEM).XRD results show that the major phase of coated iron oxides on activated carbon is magnetite (Fe3O4). The specific surface area of activated carbon was found to be reduced after the impregnation of magnetite particles on the surface. The SEM micrograph shows the aggregation of the iron oxides on the surface of activated carbon. M-ACwas found effective in removing DETA (diethylenetriamine) species and metal ions from solutions. Cu (II) with initial concentrations from 5 ppm to25 ppm in solution is removed by more than 99% with the addition of 0.1 wt.%ofM-AC. For the removal of 25 ppm DETA species from solution, an addition of 0.5 wt.% of M-AC is required due to the larger size of the DETA molecule. Moreover, M-AC showed a good loadingproperty for nickel and gold ions from solutions. M-ACshows a better adsorption capacityover activated carbon and its potential applications in carbon-in-pulp for gold leaching and waste water treatment. Keywords: magnetic activated carbon (M-AC),diethylenetriamine (DETA),metal ion,adsorption

Sep 1, 2012

By Danuta Szyszka

This paper presents results of tests performed to determine minimum concentration of a surfactant used at which coalescence of air bubbles during flotation has low probability to occur. The measurements of the critical coalescence concentration, also known as CCC, were carried out in a device consisting of glass cell into which air was pumped by peristaltic pump through capillaries. The flotation foam was recorded with a high resolution digital camera. Basing on the video records, average diameters of the air bubbles were measured and the values obtained were subsequently used to determine the CCC values. The author of paper determined the CCC values of surfactants tested using the linear regression method, and subsequently analyzed the results obtained. To define initially the capability of a tested surfactant to flotation, efficiency of multiparticle model flotation and flotation of individual size fractions were determined in a flotation apparatus for laboratory use in the presence of only foam making agent at CCC value pre-determined during the tests previously carried out. The tests of coalescence phenomenon were carried out with use of selected flotation frothing agents.

Jan 1, 2014

By Rodolfo Silva, Antonio Peres, Afonso Martins, Gilberto Ramalho, Mario Cabello

The consumption of aggregates in civil construction has increased considerably in Brazil for the last years. The extraction of sand and gravel generates significant environmental impacts. As the quarries and sand deposits are getting exhausted near the big cities, the price of aggregates is increasing. Meanwhile, the extraction of quartzite (dimensional stone) in the state of Minas Gerais has been done mostly in small quarries, with very low recovery, generating approximately six million tons of wastes a year, which causes pollution, increases final prices of products, decreases the life time of quarries and ends up in the closure of enterprises. The government agencies and the quarries’ owners understand that only by finding applications to wastes there will be development to the sector. The aim of this investigation was to study the application to the quartzite wastes as aggregate in the civil construction. Samples of quartzite wastes collected in a quarry were characterized by petrographic analyses. Laboratory tests of crushing and grinding were done to analyze the viability of reducing the size of coarse material to a finer one to be used as raw material in industrialized mortars and concrete pre-molded components.

Jan 1, 2014

By A. Collings, A. Farmer

Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation. This effect may be utilised in lowering the level of iron contamination in silica sand used for glass making, in improving the sharpness of electrostatic separation of heavy mineral concentrates, in shortening the time of leaching of minerals and in improving the selectivity and recovery of flotation processes. Parameters affecting the efficiency of these processes, such as input power and levels of reagent addition, are discussed. In particular, we present data showing the relationship between power input and the particle size of surface coatings removed, which can be explained by the Derjaguin approximation for the energy of interaction between a sphere and a flat surface. Pilot scale studies, using commercially available components, are currently being used to assess process viability and will be compared with laboratory scale results.

Jan 1, 2003

By A. Morrison, D. Mesa, P. R. Brito-Parada

"Froth flotation is the most widely used mineral separation technique. It is based on the relative hydrophobicity of valuable and gangue particles. In a flotation tank, two distinct zones can be identified: the pulp and the froth. The pulp is a turbulent region in which hydrophobic valuable particles attach to air bubbles while hydrophilic gangue particles remain in the slurry. As the particle-laden bubbles rise, a mineralised froth zone is formed that overflows as a concentrate. Although the process is more than a hundred years old, there remain many aspects that are not completely understood, particularly for the froth zone. Thus, the rules governing the design of flotation tanks tend to focus on pulp zone parameters, which are largely based on operating data. An example of this is the design and operation of impellers. These tend to be designed paying attention to hydrodynamic phenomena in the pulp zone, but their effect on the froth zone has not been completely addressed. The role of impellers in a flotation tank is to break the air bubbles in order to generate smaller ones and to provide an environment that enables the collision between those bubbles and the particles in the slurry. This usually creates turbulent regimes that can affect the pulp-froth interface, destabilising the lower regions of the froth and affecting the overall performance of the process. Different impeller designs and retrofit modifications have been proposed in the past, addressing some of those issues. However, there is no systematic study of the effect of different impeller designs on the bubble size in the pulp and its links to the stability of the froth. This work tested the impact of an impeller designs combined with the use of a stator on the performance of an 87 litres continuously operated laboratory-scale flotation tank, with a focus on bubble size in the pulp and froth stability. The results showed that the implementation of a stator system decreased bubble size and increased froth stability. That resulted in an increase of mass pull, measured as a proxy of metallurgical recovery."

Jan 1, 2018