Search Documents

By Mustapha Zergoun

This paper presents the results of load tests to assess the vertical load carrying capacity of concrete expanded base piles, or pressure injected footings, for various projects located near Vancouver, British Columbia, Canada. The site subsurface conditions and load test methods are described for the Vancouver International Airport site and the test results are reviewed under both compression and tension loading conditions. The pile load tests at Vancouver International Airport are compared to load tests at other sites near Vancouver. The pile load test results are reviewed with respect to available methods of estimating the vertical capacity of this type of piles. The effect of ground improvement by densification on the load test results is considered. The limitations of tension load tests on single piles with respect to uplift resistance of pile groups under seismic conditions are pointed out. Recommendations are proposed regarding pile load test methodology to estimate ultimate vertical load carrying capacity of plies for limit state design.

Jan 1, 2004

By Maurice Bottiau

When dealing with displacement auger piling, some general and fundamental issues have to be considered, irrespective of the system. More than with other pile types, the interplay between the soil conditions and the design and execution is of outstanding importance. This paper intends to address these issues and to summarize some critical matters in terms of design, execution and control such as : ? Importance of a reliable soil investigation ; ? Summary of the design as it is addressed in Europe for this category of piles ; ? Criteria for a good choice and control of the correct asset of the piles ; ? Importance of the concreting phase; ? Relation between the power and the engine characteristics of the drilling equipment with the final bearing capacity. For each of these issues detailed examples will be given as well as results of load tests and in-situ control during execution.

Jan 1, 2003

By Ramdane Bahar

The new Algiers airport building is a reinforced concrete building of more than 80 thousand square meters of floor slabs. It is located at Dar-EI-Beida, near the old passenger terminal, about 20 km east of Algiers. The project is designed to receive about six millions passengers annually and leaves the possibility of future extension. Due to the presence of a top layer of compressible soil and great concentrated loads transmitted to the foundations, the building is to be founded on 1730 bored piles of 1.2 meter diameter varying in length between 14 and 28 m. Construction work started in 1986 and was interrupted in 1996 due to financial difficulties when the structure was almost complete. The structure was left unattended for more than three years without any weatherproofing and in 1999 a new firm was appointed to complete the work and hence an evaluation of the existing structure was necessary. This paper describes and discusses the foundation design, construction supervision, site quality control and assessment by the parallel seismic method of the deep foundations built in cohesive soils. The variation in soil conditions and identified geotechnical and hydrogeological problems associated with the development of the area, required a thorough knowledge of the soil conditions. A variety of tests, involving more than 200 locations, were carried out. The ground investigation, pile tests as well as different problems encountered during piles construction, are presented.

Jan 1, 2002

By Donald A. Deardorff

The capacity of a helical pile can be determined analytically using the individual bearing or cylindrical shear methods which are dependent on soil strength parameters and helical bearing area. The torque correlation method is widely used in the helical industry to determine the capacity during installation by monitoring torque during the final seating of the helicals. This method has been shown to be a better predictor of strength than the individual bearing or cylindrical shear methods. To determine capacity using the torque correlation method, the final average installation torque (ft-lbs) is multiplied by an empirical torque correlation factor (Kt, ft-1). Kt values have been well documented for square bar shaft helical products and can vary from about 3 to 20 ft-1 depending on pile geometry and soil type. A default value of 10 ft-1 is generally used for all square shaft sizes and soil conditions. Less research has been done on determination of Kt for round pipe shaft helical products. Studies have indicated that factors which affect Kt include soil type/strength, number of helical plates, helix spacing, helix pitch, depth of embedment, downward pressure (crowd), shaft diameter (round pipe) and load application direction while other studies have discounted some of these factors as inconsequential. This paper reviews past research findings regarding Kt determination for square and round pipe shaft helical products and presents a case history of round shaft helical pile installations in Chicago clay which resulted in much lower than expected Kt values.

Jan 1, 2007

By Wolfgang G. Brunner

In the far north of Uttar Pradesh Province in the Indian Himalayas, the 280 MW Dhauliganga hydroelectric power plant is under construction by National Hydroelectric Power Corporation (NHPC), a state- owned enterprise, and a joint venture of Kajima Corporation of Tokyo and Daewoo Corporation of Seoul. This project sets out to develop the lower section of the mountain cascade of the Dhauliganga River, a tributary of the Sarda River, with a 311 m gross head. The 1360 km2 mountainous catchment area is bounded in the north- east by the Chinese border and in the south- east by the Nepalese border. The dam project is located in a remote area north of the principal town of Darchula of the upper Sarda valley, which is one of the seismically most active regions of India. The 56 m high rock fill dam, which will be the first of its kind in India, is faced with concrete and has a 1 m thick, at its crown 270 m long and over 70 m deep cut- off wall of plastic concrete below its toe. The cut- off wall, with a total area of 7500 m2, is constructed by a combination of Bauer hydraulic grabs, assisted by chisels and a Bauer BC 40 cutter which enables the overlapping joint system to be installed, guarantees optimum verticality and enables the cut- off to be keyed into the bedrock formation.

Jan 1, 2004

"Premissas BásicasCaracterísticas do concreto centrifugado(Spun concrete characteristics)Aplicação em obras de engenharia de fundações(Application engineering works foundations)Logística de fabricação e transporte(Manufacturing logistics and transportation)Emendas x uso de aplicação(Amendments x use application)Geologia brasileira, da região costeira a presença de grandes bolsões de argila mole(Brazilian geology, coastal region the presence of large pockets of soft clay)Influencia do sistema de cravação(Influence of driving system)Transferência da Energia Aplicada(Applied Energy Transfer)Estacas longas(long piles)Controles executivos (diagrama de golpes, nega, repique elástico, ensaios de carregamentodinâmico, provas de carga).(Executive Controls (blows diagram, sets, elastic rebound, dynamic load tests, load tests).)ECD – aplicação da metodologia do DIETECD - application of the methodology DIETBrazil has a highly variable geology all along its coast that directly influence the choose of foundation type, being too employed the use of reinforced spun concrete piles initially ranged in diameter from 60 to 80 cm. Over the past 10 years with the advent of investment in marine works projects began to demand a new range of piles with diameters greater than 100 cm and in the absence of amendments.On land is also very remarkable the presence of regions with large layers of soft clay, in prime areas that have been explored. A classic example is the Barra da Tijuca in Rio de Janeiro that has suffered from the housing boom growing toward these regions. In these regions it has been very common driven lengths of about 40.0 meters, which basically go through thick layers of soft material or unconsolidated and they will find strength in depth with residual soil layers or even the bedrock.The spun concrete has great qualities for application in deep cuttings resulting from the production process, which gives a redistribution of fresh concrete mass collaborating with the particle size distribution effective loss of water that is thrown to the center stake being subsequently discarded. Consequently this contributes to a reduction in the factor a/c that is directly connected to increase strength.The fact that there is a sort of concrete helps to reduce voids in the mixture, which increases the durability characteristics. This condition made it possible to employ the spin technique on poles, which are directly linked to aggressive media in large urban centers.Another very attractive feature is that the centrifuge process can work with concrete with the lowest percentage of mortar and more gravel. This concrete mix directly contributes to increasing the specific modulus of elasticity, thus allowing a greater capacity to absorb the energy of the blows transferred with less deformation.Despite the great potential of land application of prefabricated spun concrete stakes there are only three factories and its limitation is the cost of transporting manufactured for the various regions, since all transportation is done by road.For its transportation is carried out exclusively by trucks, this limits the size of cuttings being produced commonly in length from 11.0 to 12.0 meters in length and smaller compositions. For use in long piles of works is resorted to amendments in the form of metal rings, concreted near the ends of the stakes, with the transfer through steel bars in CA-50 welded to the ring. Usually run in steel ASTM A-36. Later in the work these rings are welded with coated electrode.In the case of maritime stakes are very used to drowned splicing technique, which basically consists during the spin process leave one end with the armor of the apparent stake and work together two elements and make specific, with superior resistance to the prefabricated stake.This study in addition to briefly introduce the process of manufacturing, design and logistics presents a detailed study of applicat"

Jan 1, 2015

By Charles G. Crans, Naresh Gurpersaud

"Toronto’s Union Station, a National Historic Site occupying an entire city block, is the busiest commuter rail transportation hub in Canada. An extensive project is being undertaken to revitalize Union Station while maintaining the historical significance of the building and minimizing disruption to commuters. A significant stage of the revitalization involves excavation indoors, to a depth of up to 5.5 m below the existing floor level to create space for a new transit concourse and a new lower-level pedestrian retail concourse. A hybrid excavation support system utilizing micropiles as soldier piles was constructed over an 18 month period between 2010 and 2011.Development and testing of connections between the micropiles, shotcrete facing, lagging, walers, and tiebacks presented significant challenges. The existing viaduct structure was constructed in the 1920’s on land reclaimed from Toronto Harbour, so there was significant (and ongoing) uncertainty with respect to buried obstructions including relic timber wharfs and abandoned steel and timber piles. Collectively all these conditions precluded the use of conventional methodology; new techniques, installed using modified equipment, and for the first time in the Greater Toronto Area, were required.Details of the existing site conditions, installation challenges, design, construction and performance of the hybrid excavation support system inside this historic structure are presented.INTRODUCTIONUnion Station in Toronto, Ontario is the busiest passenger rail facility in Canada, with 65 million passengers annually and an average of 200,000 passengers each day. Construction of the station was completed in 1920. It has been designated a National Historic Site of Canada and inducted into the North America Railway Hall of Fame in the Facility and Structure category.The Union Station Revitalization Project (USRP) was tendered in 2010 and awarded as a 6-year, $450M construction management / trade contract package. Included was a large scale grade reduction, referred to as “The Dig Down”, to create two basement levels and this required extensive excavation support constructed entirely indoors within the active station setting."

Jan 1, 2017

By Takashi Enomoto

"The cement deep mixing (CDM) method has a wide range of applications, both on land and at sea. This paper describes the features of the equipment on CDM vessels engaged in maritime construction in Japan: the DCM No. 3 barge, the DCM No. 6 barge, and the DCM No. 8 barge. The DCM No. 3 barge is a large vessel with a mixing area of 5.7 m2. The design of the elevator of the deep mixing unit on the DCM No.3 barge enables us to conduct deep underground/ sea operations. This enables us to conduct mixing at depths of up to 52.6 m below the seabed and up to 70.5 m from the water surface. Additionally, since the tower is installed on the center of the barge, it has excellent stability. The DCM No. 6 barge and DCM No. 8 barge are mid-sized vessels with a mixing area of 4.6 m2. The DCM No. 6 barge was fitted in 2013 with energy conservation equipment and upgraded to an environment-friendly CDM barge. The energy saving upgrade used electric power, instead of hydraulic power, by inverter controlled alternating current motor for both mixing unit and main hoisting winch. This enables the using on effective use of regenerative power when the deep mixing unit is lowered. A feature of the DCM No. 8 barge is that it has an inclinable tower located at the bow section for elevating the deep cement mixing unit. Since the tower can be greatly inclined, the hull has a lower center of gravity and greater stability when the vessel turns. This also allows the vessel to pass below bridges and simplifies cruise preparations, outfitting and dismantling work.INTRODUCTIONThe cement deep mixing method (CDM method) involves mixing and stirring a cement-based solidifier into soft ground to rapidly bring the ground to the desired firmness. This method is used to suppress ground shear deformation, increase strength, increase slip resistance, and mitigate liquefaction and subsidence. It has been recently used in Japan in the construction of revetments at controlled waste disposal sites, both to boost the strength of the seabed and to prevent the seepage of waste matter and other pollutants. Undertaking CDM construction work at sea requires specially constructed marine construction CDM vessels. Since CDM construction at sea entails many more restrictions on working conditions than construction on land, the vessels themselves sometimes need to be modified. This paper will describe 1) the remodeling of the turrets and mixing machinery for mixing to great depths in deep water (DCM No. 3 barge with eight axes); 2) the upgraded of equipment on board CDM vessels after accounting for environmental considerations (DCM No. 6 barge with four axes); and 3) the use of a inclinable tower (DCM No. 8 barge with four axes)."

Jan 1, 2015

By W. Morgan NeSmith

A drilled displacement pile program was utilized for the expansion of an existing power plant in Cohasset MN adjacent to the Mississippi River. The drilled displacement (DD) pile is an innovative foundation type that provides exceptional value in some geologies. In the U.S., DD piles have typically been used in coarse-grained soils due to the large friction capacities that can be generated by the piles in these conditions. This project was the first large scale experience for the project team where it was anticipated that significant portions of the DD pile capacity would be developed in primarily fine-grained soils. The project site consisted primarily of variable amounts of fill overlying predominantly low plasticity alluvial silts. In some cases, alluvial silty sand layers were encountered within the expected pile installation depths. Alluvial sands were typically encountered below the silts, in some cases within the expected pile installation depths. The project team developed a probe and pile load test program to address the variable subsurface conditions across the site. The program included monitoring various parameters (including applied torque and tool penetration rate) during the drilling portion of the pile installation using recently developed data acquisition techniques. This data was used to estimate the rig energy, or Installation Effort (IE), required for pile installation. IE profiles from the test and indicator piles were compared with subsurface data available from a number of previous site characterizations. Additionally, Cumulative IE values were compared to an in-house database of IE vs. DD Pile Capacity. Final production pile toe levels were based primarily on IE values selected from this comparison. The IE data collected during production was also used to address large variations in pile-cutoff elevation (relative to a fairly uniform ground surface elevation).

Jan 1, 2008

By Narong Thasnanipan

Performance of diameter 1.5 m toe-grouted bored pile founded at depth 44 m in sand-gravel formation of Chiang Mai City is presented in this paper. Toe grouting was applied by using tube-a-manchette method. Effectiveness of toe grouting was observed from the standard penetration tests conducted immediately below pile toe through grouting pipes at two stages, prior to grouting and three weeks after completion of grouting. Improvement of pile end resistance by toe-grouting is demonstrated with a series of back analyses carried out by load-transfer method employing hyperbolic transfer function. Construction experience of large diameter deep-seated bored piles in multi-layered subsoil and practical aspects of toe-grouting are also briefly discussed.

Jan 1, 2002

By Tony Suckling

"As we head toward the United Nations Climate Change Conference in Copenhagen in December, the environment and sustainability will become headline news for a while. Governments are expected to agree to a set of binding targets to reduce carbon emissions probably before 2020, and certainly before 2050. This will, in effect, initiate a low carbon economy in many parts of the world. Sustainability has mainly been rhetoric so far, the exceptions being projects for those looking to the long-term future and not for short-term financial gains.The probabilities and consequences of negative impacts on the environment and on society over the short term and in the long term can be assessed and mitigated, but mitigation often adds cost. Also, we cannot know what technologies will be available, say 1,000 years into the future, which is about 40 generations of our society. It is easier to have a connection with 100 years into the future, which is only about 4 generations. Individuals may have a different sense of sustainability, and place a different value on mitigation, its cost, its importance and its potential impacts.Sustainability means different things to different parties on a construction project. For example, a land developer is likely to have a different view on the design in terms of sustainability than that of the designer. The developer may also likely to be more interested in sustainabiliy if there are tangible economic benefits that might accrue. Achieving sustainability on any project, leads to conflict between competing interests or demands cooperation between the economic and technical sectors involved. The foundations for a building or bridge, by definition, need to interact with the ground whose behaviour cannot be dictated by man. The aims of sustainability are the same as for the building or bridge, both of which are constructed of manmade materials, but it is less clear how they should be achieved. An example is the driven pile that does not produce spoil waste, but is likely to be too noisy to be acceptable in an urban environment. This then begs the question, should the public accept the nuisance of short-term pile driving to achieve a more sustainable foundation? Additionally, the question has to be asked, can the deep foundations industry develop its techniques and products to help make them more acceptable and appropriate more often than is possible now?"

Jan 1, 2009

By Anand J. Puppala

This paper provides information on various evaluation studies conducted to assess the CPT based interpretation methods. Salient findings from these evaluations are summarized. Additionally, a comprehensive evaluation study on both LCPC and European methods was performed on twenty-four driven piles selected from four different states. This evaluation showed that the LCPC method predictions are close to measured pile capacities. The European method provided good predictions for driven steel piles. Overall, both methods' predictions show high values of coefficients of variations, which are in agreement with other studies. Overestimation of driven concrete pile capacities is attributed to large estimations of unit point resistance. Suggestions to consider appropriate CPT based pile capacity interpretation methods are presented.

Jan 1, 2002

By K. C. Foye

Use of load and resistance factor design (LRFD) of foundations is growing, from offshore applications to bridge applications and beyond. The development of load and resistance factors for design has traditionally relied on calibration to traditional factors of safety. This technique, however, offers little insight into the challenges of pile design. This paper discusses an approach to LRFD factor development that seeks to isolate the various sources of design uncertainty. Using this approach, reliability analysis is used to develop resistance factors for the design of driven pipe piles in sand. These findings shed light on many aspects of the ongoing discussion of how LRFD can be successfully applied to pile design.

Jan 1, 2008

By Denis Huber

The technical assessment of the final works on the "Stéphany Palace" project at Menton in France's Alpes-Maritimes region shows the importance of daily project monitoring based on the observation method recommended by the European standard Eurocode 7 which applies to Foundations and Geotechnical Engineering. Excavation operations to a depth of 10 m near the France-Italy railway track and adjacent buildings required precise observation of land deformations, regular piezometric monitoring as well as special design arrangements. Temporary active tie-rods were thus placed in phases in order to control deformations in the retaining structures resulting from excavation operations. The Menton region, terminating the Alpine arc of mountains, naturally required the consideration of seismic forces in phase in the lower floors of the building, directly linked to the buried walls. These calculations were carried out in accordance with the PS69/92 rules, calling for an increase in dynamic thrust under the effect of gravity field rotation.

Jan 1, 2002

By Trent Dreese

For critical velocities in gravel units we use Bush-Luckner, Sichardt, other empirical equations, and equations derived from laboratory experiments too. On the base of these, we compiled critical velocity - permeability coefficient dependencies. Under the lower border of these dependencies sand particles can't be moved, and thus they are stable. For critical velocities in the fissures of flysh and volcanic rocks we use Ronzhin (1974) criteria derived from laboratory experiments in Russia. Maximal filtration velocities measured by tracer methods in gravel soils and in fissured rocks have smaller values then the critical ones.

Feb 10, 2003

By Waddah Akili

This paper describes the steps taken in planning, developing, and executing a case study/ case history course in geotechnical/ foundation engineering at an international university. The paper sheds light on: how a “workable” format for the course was arrived at; the organization of the course; and the results of evaluating the effectiveness of this approach versus traditional lecturing. Problems and challenges that could arise when offering the course for the first time are also addressed. Embedded in this experience and its related protocols are: the emphases on engineering design and the practice, teamwork and leadership development, organizational management, and oral and written communication skills. The paper concludes by confirming that discussions, through an open forum, are judged to be superior to traditional lectures in improving critical thinking, cultivating desirable personal attributes, and acquiring problem-solving skills.

By S. Y. Zhou

Excavation with earth retaining is one of the main technological means in deep foundations and underground engineerings. Several construction methods which have been used in China are introduced here with some examples from engineering practices in Shanghai, including foundation pit protected by steel or RC sheet piling or D-walls, open caissons and pneumatic caissons, shield tunnel and pipe jacking, etc. This paper also discusses the prospect in development and utilization of underground space in China and the challenge to which the engineers specialized in deep foundations have to face.

Jan 1, 2010

By W. H. Craig

Techniques have been developed for installing model piles into beds of soil under high sustained acceleration levels aboard a centrifuge. These piles have been subjected to static and/or cyclic lateral loading in order to assess their performance and provide a data base for assessment of various design techniques for laterally-loaded single piles. From measured bending moment profiles the so-called 'p-y' curves have been deduced using fifth order splines for curve fitting, followed by subsequent differentiation and integration. The results show some divergence from the predictions of the semi-empirical designs, but these latter are generally found to be acceptable.

Jan 1, 2010

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects, derive p-y curves for reinforced concrete fixed head piles and to validate currently available p-multiplier models. The piles are identical in diameter of d=2 ft and were tested in similar soil conditions. The single pile as well as in three piles within the pile group were instrumented with internal sensor instrumentation to record pile curvatures. External instrumentation was used to control and measure the lateral displacement of the specimens. Experimental studies were supported with analytical models to enable comparisons and offer design recommendations. All test specimens were tested to structural failure and group interaction factors ranged between 0.8 at small displacement levels and increased towards unit near structural failure. A set of p-multipliers was found to reproduce an accurate fit to the available test data.

Jan 1, 2010

By Willie M. NeSmith

In the Metropolitan Atlanta Area today, augered, cast-in-place (ACIP) piles will be considered on most projects where deep foundation support is required. ACIP piles were first used in Atlanta in the late 1960s, and application began to blossom in the mid-1980s. Current design practice for ACIP piles is addressed in another paper in this conference. This paper describes the evolution of the ACIP industry in Atlanta, and details the use of ACIP piles on major projects in the Atlanta area.

Jan 1, 2003