Search Documents

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete walls. PRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete wallsPRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By Eric Brandner

Expansive soil formations can be found throughout the United States. When subjected to wetting, many of these formations have the potential to swell and exert large uplift forces which can significantly damage lightly-loaded structures. Designing an economical foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material, or drilled shafts, can be costly and problematic. Piles made from recycled polymer materials may provide a solution. Due to a lower coefficient of friction along the interface than piles made from traditional materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure which minimizes the risk of significant structural damage. This paper presents the preliminary results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six 13 in. (330 mm) diameter recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. The piles varied in length from 15 ft. to 25 ft. (4.6m to 7.6 m). Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity, while the additional four piles are being subjected to long-term monitoring of uplift movement. A cast-in-place concrete pile, with a diameter of 6 in. (152 mm) and length of 15 ft. (4.6 m), was also installed at the test site for monitoring. The preliminary results indicate that the use of solid recycled plastic piles is a viable alternative for support of lightly-loaded structures in expansive soil environments.

Jan 1, 2009

By Aditi Sharma, Sumanta Haldar

Scouring of soil is the major concern forthe various hydraulic structures built in the flowing rivers since scouring impacts the bearing capacity of foundations. Hence, consideration of scouring in the design of foundations for hydraulic structures is crucial. Pile groups in bridges are subjected to combined vertical and horizontal loading due to self-weight, live loads, vehicular impacts, wind load, earth pressure, and current. Hence, an assessment of the combined bearing capacity of pile groups subjected to scour is essential for the safety of the structure. This paper aims to analyze the bearing capacity of pile group supporting the bridge under combined loading i.e., Vertical (V) and Horizontal (H) loading subjected to local scour. Three-dimensional finite element model (3D-FEM) of a 3 x 3 pile group embedded in homogeneous sandy soil is established in Abaqus (2018). Mohr-Coulomb plasticity model is used for the soil domain. The pile group is modelled as linear elastic. Finally, V-H yield envelopes are obtained with and without scour. The potential impact of different parameters, such as angle of attack, flow velocity, depth of flow, and different pile length-to-diameter ratios (L/D) and spacing-to-diameter ratios (S/D) of pile group on V-H yield envelopes is studied.

Sep 1, 2022

By Hyunsuk Yoon, Kiho Lee, Juhyng Lee, Younghoon Jung, Junboum Park

"The environmental double pile method is presented as a device to improve the engineering properties and to clean up contamination of low-permeability soil. This method is one of the novel technologies based on the concept of one step process. It can be applied to low permeable contaminated ground for site reuse. It uses piles to improve drainage, contaminant remediation, and bearing capacity of the ground. To evaluate the on-site applicability of this technology, drainage and strength properties of the environmental double pile were assessed by a series of experiments and numerical analysis. Environmental double pile was found to be a feasible alternative method to improve contaminated soft ground.Korea is a peninsula with many coastal industrial zones. These zones are located in regions mostly underlain by soft ground with low permeability and adjacent to industrial areas that can be contaminated. Therefore, a new region-specific remediation method is required to achieve environmentally sustainable development. This research introduces the Environmental Double Pile (hereinafter, refer to as EDP) for the lowpermeability contaminated ground and focused on both contaminant remediation and soft ground improvement. Basically, the EDP is quite similar to sand compaction pile (SCP). The SCP has been studied extensively to improve soft ground (Braja 1999; Hansbo 1994; Madhav and others 1978; Taylor 1948). But unlike SCP, EDP is filled with oyster shells instead of sand and an inner pile is inserted in the center of this oyster shell filled-zone. Therefore, it is a double pile consisting of the oyster shell pile and the inner pile, as depicted in Fig. 1."

Jan 1, 2005

By Edwin W. Hickey

This paper briefly discusses the geologic conditions in South Florida relative to the design, construction, and performance of deep foundations. The subsurface conditions in this area are unique in that the rock layers are highly porous and often very soft, and are sandwiched between layers of typically loose, uncemented quartz fine sands. Due to the high porosity of the Miami Limestone, 4-inch diameter rock coring is often required to obtain intact samples, and dewatering of excavations is sometimes difficult or impossible. The sand layers, typically tens of feet thick, are very loose to loose in relative density and have been the cause of unexpected large, deep foundation settlements. The engineering properties of the various geologic formations are discussed, along with typical deep foundation types used in the Miami area prior to and after 1980.

Jan 1, 2003

By A. Partos

It was decided to build a fourteen-storied office building over a six-storied garage and a four-storied office building. The high vertical and horizontal loads required foundations on rock approximately 18m below street level. Drilled piers (caissons) were selected. Eight caissons (1.98m diameter) were installed through the six-storied garage and four caissons from a temporary deck at the location of a former two-storied building. Excavations were done by the slurry method. Proof testing of rock was done before construction by test borings and during construction with a core barrel of small diameter. Quality control measures included telecommunications between ground crews and the equipment operator on the garage roof; records of field observations and testing of bentonite slurry and rock; and a continuous evaluation of all information. Instruments were installed in one caisson to monitor load distributions and curing of concrete.

Jan 1, 2010

By H. R. Masoumi

This paper presents a numerical model for the prediction of free field vibrations due to vibratory and impact driving. As the focus is on the response in the far field, where deformations are relatively small, a linear elastic constitutive behavior is assumed for the soil. The free field vibrations are calculated by means of a coupled FE-BE model using a subdomain formulation, proposed by Aubry and Clouteau (1992). The model is validated by means of the results of Kaynia and Kausel (1991) for the impedance of a single pile. First, the case of vibratory pile driving is considered, where the contributions of different types of waves are investigated for several penetration depths. The results show that in the near field, the response of the soil is dominated by a vertically polarized shear wave, whereas in the far field, Rayleigh waves dominate the ground vibration and body waves have been importantly attenuated. Second, the case of impact pile driving is considered. A linear wave equation model is used to estimate the impact force during the driving process. Furthermore, it is investigated how the soil stratification influences the ground vibration considering the case of a soft layer on a stiffer half space. The results show that when the penetration depth is smaller than the layer thickness, the layered medium has a small influence. However, when the penetration depth is larger than the layer thickness, these effects become more significant. Finally, the computed ground vibrations are compared with experimental data reported in the literature.

Jan 1, 2006

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

By Xuhui

Pile foundations are underground projects which are carried out under complicated site conditions, so it is difficult to summarize their characteristic patterns from the everchanging practical pile foundations. In combination with theories, the paper analyses the effects of sound reinforced concrete piles and various types of defective piles on the propagations of stress waves. Through testing on prototype pile models, by use of the transient dynamic method and comprehensive analysis in both time domain and frequency domain, their reflection characteristics and patterns are acquired. In addition, discussions are carried out in combination with some real projects. Our model tests include comparison of large scale pile models of 20X20cm in cross section, 5. 0m in length respectively in air, standard sand, and natural stratum; prototype model tests of digged piles of 0. 7-1. 2m in diameter, and 18m, 30m in length; prototype model tests of bored piles of 0. 6m, 0. 8m in diameter, 12-20m in length. Test results show that no matter in air or buried in medium, the intrinsic characteristics of sound piles and various types of defective piles are fixed. In their time domain waveforms and spectral diagrams, obvious regularity are shown, which proves that the relations between the pile natures and their dynamic responses are fixed, which provide basis for correct judgement of pile soundness and natures of defective piles.

Jan 1, 1991

By Lisheng Shao

Soil mixing and jet grouting have been widely used to support heavy structures such as tanks, cement silos, and storage buildings. Although the installation methods vary between soil mixing and jet grouting, the end product of soil-cement columns behaves similarly in supporting structure loads. In many cases, soil-cement mass treatment offers the owner savings over driven/drilled piles. This paper discusses the design methodology, production work, and quality control, with supporting figures, of a recent large complex tank farm project. The project consisted of constructing six above-ground steel storage tanks and an approximately 700-foot-long fill slope. The tank farm site is located in an industrial area of southern California, with highly variable subsurface conditions consisting of compressible soils and buried construction debris. The compressible soils necessitated that the new tanks be supported on deep foundations. A test pile program performed previously at the site showed that conventional driven concrete piles were not feasible because of buried construction debris, therefore a soilcrete system was proposed. Site design included evaluating the total and differential settlement and column group bearing capacity under both static and seismic loads. Extensive field and laboratory testing confirmed the design soil-cement strength and modulus of both the soil mixed and jet grouted soil-cement columns. The project operation and quality control programs are also included in this paper.

Jan 1, 2010

By Sebastian Lobo-Guerrero

Welcome to DFI45! our first on-line annual meeting. We cannot deny the severe impacts that the COVID19 pandemic is having in our industry and our lives. We extend our support to all of our members that have been impacted in many different ways. But through the middle of this difficult and challenging times, our beloved annual conference emerges, trying to re-unite our industry and remind us why we love what we do so much. DFI45 was not originally planned to be delivered virtually, but as our world changed, we adapted. Adversity became an opportunity to re-invent our annual conference. Thanks to the vision of our Organizing Committee, we saw the amazing new possibilities and DFI45 is today a reality. Our theme for this year is People + Purpose + Passion. This theme was decided before the COVID 19 pandemic started, but today it is more relevant than ever before. We are a group of very diverse people at DFI. Our organization includes Contractors, Consultants, Suppliers, and Academics just to name a few sub-groups. But we all have a common purpose and try to find common ground. We are all extremely passionate about what we do, and this excitement is really what makes this organization what it is today. This conference celebrates this passion as you can see in our three main Keynote Sessions. On a local scale, we want to go back and remember the contribution of our industry to our beloved National Monuments in Washington D.C. On a national scale, we want to explore and recap the development of Government Guidelines and Specifications that became the world standards. And finally, we want to close the conference with a session celebrating the family legacy and share amazing stories of families with multiple generations working in our industry. Besides our Keynote Lectures, the conference is full of exciting content such as several case histories, experimental research in deep foundations, applications of new technologies, business aspects and risk management considerations for deep foundations, just to list a few. We also have our now traditional events such as the Hal Hunt Lecture, Awards Reception, DFI Educational Trust 5K Fundraiser, etc. For the first time, all this content will be delivered using different virtual formats, including on-demand presentations, plenary sessions, interactive chat rooms, etc. We are excited about these possibilities. To conclude, we need to recognize the people that against all odds made this conference a reality. First our sponsors, they adapted to the most abrupt change never thought before, and they always stayed there with us, providing unconditional support. Without them no conference is possible. Next, our Organizing Committee that re-invented the concept of an annual conference and found new and exciting ways to make this happen! Our Technical Program Committee led by our Technical Program Chairs, Jennifer Nicks and Gregg Piazza, showed us that nothing is impossible. And last, but not least, the amazing DFI staff that make dreams reality. It has been an honor to serve as the Conference Chair for DFI45. It is an experience that will stay with me for the rest of my career. Conference Chair: Sebastian Lobo Guerrero, Ph.D., P.E. American Geotechnical and Environmental Services (A.G.E.S.)

Oct 27, 2020

By Michael D. Justason

"In January 2009, long-time competitors, Anchor Shoring & Caissons Ltd. of Toronto and Bermingham Foundation Solutions of Hamilton, joined forces to tackle one of the Greater Toronto area’s largest deep foundation projects: the West Toronto Diamond Rail Grade Separation. The two companies formed the “West Diamond JV” and succeeded in winning the contract from the Canadian National Railways. This deep foundations work was the first and most significant part of the $300-million-plus rail grade separation project. A big part of the job turned out to be dealing with local government regulations and citizens’ concerns with noise and vibration.The project is approximately 10 km (6 mi) northwest of downtown Toronto in an area of mixed-zoning including light industrial, commercial and residential buildings. The area is commonly called the “The Junction,” because of the heavy rail- traffic. The “West Toronto Diamond” refers more specifically to the railway junction where the North-South tracks of Canadian National (CN) Railway meet at a level crossing with the East-West tracks of the Canadian Pacific (CP) Railway. The goal for this part of the project was to convert the West Toronto Diamond into a grade-separated junction by depressing the CN lines under the CP lines, thus allowing commuter rail carrier, called GO Transit, intercity carrier VIA Rail, and CN freight trains to pass through the new underpass.Dawn Tattle, president of Anchor Shoring & Caissons says, “not only is the site in a densely populated area adjacent to homes and businesses, the crews worked adjacent to active rail lines with numerous trains passing daily. During the 7-hour working day, approximately 60 trains passed through the site in very close proximity to working crews.” Safety was paramount. While trains were passing through the site, it was a railroad requirement that all equipment and men stop working. In addition, at those times, all personnel were required to stay 6 m (20 ft) from the tracks and were required to face the tracks. For the faster commuter trains, this work interruption could last as little as 2-3 minutes, while interruptions caused by the slower freight trains could last as long as 25 minutes. The most disruption to the site occurred during the morning commute between 7 to 9 a.m., so work did not really get underway until after that time. Once work finally commenced the race was on to finish as much as possible before the afternoon commute – hence the shortened work day. The amount of disruption caused by the trains was a big unknown faced by the JV going into the project, but crews adapted quickly to the very unusual work environment"

Jan 1, 2012

By Danny Déry-Chamberland, Peter Bowman, Michael Byle

"The Barrage des Quinze dam is a concrete sluice dam consisting of 19 spillway sections, each of which is approximately 7.6 metres wide and 14.5 metres deep. Rehabilitation efforts being performed on the dam including demolition and improvement of the roadway and spillway sections and grouting to mitigate underseepage. Initially, conventional cement grouting was attempted and was successful in 14 of the spillway sections, but unsuccessful in 5 of the sections due to the high water flows which washed the grout away. The removal of the roadway and portions of the piers during construction temporarily reduced the stability of the structure limiting grouting pressures that could be applied. This and the substantial high water flows (leakage) beneath the dam between the concrete/rock contact and within fractures in the upper rock formation created a challenging situation to create a cutoff.A grouting solution was developed that involved implementing several different grouting methods and materials including balanced high mobility grouts (HMG); low mobility grouts (LMG); polyurethane grouts; and sodium silicates. Because of the critical scheduling for the work, multiple approaches were planned and made available on site so that the work could proceed with the best technology with little, if any, time loss. The end goal of the grouting program was to create a seepage cutoff beneath the 5 sections of the dam in a stepwise process. The initial step was to fill the large openings and create a grout barrier to reduce the high water flow. The second step was to seal the contact between the base of the dam and the bedrock; and the third step was to complete closure by grouting a deep grout curtain into the underlying rock. Other features of the work included an extensive grout mix testing program, water pressure testing, borehole camera survey, and monitoring of the grout injections."

Jan 1, 2016

By John C. Ryan

The Emeca Pile Splice, an innovative mechanical prestressed concrete pile splice, is the first robotically welded splice to be fabricated in the United States. An analytical and experimental study was conducted to establish the capacity of the standard splice for 12-in. and 14-in. square piles. The study illustrates compliance of the splice with International Building Code (2006) requirements. A case study for a large petroleum tank foundation project in Port Canaveral, FL is presented, demonstrating the efficiency achieved through use of spliced-piles. For the case-study project, single-piece 18-in.-square, 100-ft-long piles were replaced with 12-in.-square, two-piece, spliced piles. As a result, a significant reduction of material, labor, handling, and equipment was documented for the project. Savings realized on the installed pile cost was estimated to be in excess of 30% by the owner.

Jan 1, 2010

By Donald T. Robertson

This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.

By Massimo Poggio, Gabriele Balconi, Andrea M. R. Pettinaroli, Mario Ruggiero, Riccardo Castellanza

Grouting technologies are ground treatment techniques used for modifying the behaviour of a mass of soil or rock by injecting a mixture. The sleeved port pipes (also called Tube A Manchette) are highly diffused for grouting treatment of coarse soils and fissured rocks. This paper describes a combination of jet grouting and rock grouting with MPSP (multiple packer sleeve pipe) technique that has been used to realize waterproof curtains under fluvial structures for a cascade hydro-power plant. This is composed by five mini hydro-power plants, placed along the Iskar River, in Bulgaria, and composed by a penstock followed by the power house, a spillway, and an earth dam containing the reservoir. The geology of the site is characterized by an upper alluvial deposit lying over the bedrock. In each site, similar treatments were carried out: an impervious curtain along the plant section, obtained by executing jet-grouting columns in the surficial alluvial layers and grouting the underlying fractured rock by means of port pipes. The temporary embankment, built during the works for protecting each site from the possible river floods, has been waterproofed and stabilized by reinforced jet-grouting columns. The grouting processes have been controlled and monitored by a computerized system. INTRODUCTION The Iskar river cascade hydropower plant is situated northern of Sofia, Bulgaria, and it is composed by nine plants. Actually five of them have been built and produce energy. Each plant is composed by a penstock followed by the turbine building, a spillway, and an earth dam that contains the reservoir. The Iskar rivers runs in a narrow valley characterized by diorite or diabase rocks, with an upper deposit of alluvial soil, composed mainly by gravel and sand. Each plant requires an impervious curtain under the structures and in correspondence of the earth dam: this has been obtained by means of a jet grouting treatment of the alluvial coarse soil, and a grouting treatment with cement mixtures of the underlying rock using the MPSP technology. During the construction of the structures, the site has been shielded from the river water by a temporary earth embankment that has been statically improved and waterproofed by jet grouting columns reinforced with steel tubes; this allowed to work without interruption even in case of flood of the Iskar river.

Jan 1, 2019

By George Burke

Of the three projects, particularly the extensive Nimitz II (downtown) project, a single system, which was part of the operation, was used to control the spoil. Spoil control was continuous with the work since a vacuum truck and crew was used to suck up the spoils as they came out of the borehole. So, the whole job was kept clean both during operations and at the end of the shifts. On the Sand Island project, a double system was used. Larger spoil quantities were contained within the shaft limits during the work and the cleanup or disposal of the spoils was performed during excavation.

Feb 10, 2003

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003

By George Filz, Peter R. Cali

"Unnecessarily restrictive specifications could be limiting the cost effectiveness of deep mixing (DM) applications and therefore limiting use of DM on projects where there are other options. Excessively restrictive standards demanded for strength and permeability certainly increase contractors’ bid prices, and costing the owners and, in the case of Government projects, the taxpayers more than necessary. Yet, lax or ineffective specifications often exist for some vital components of the quality assurance and quality control. In this paper, specifications for key elements of DM design and construction are examined. Recommendations are made to improve and streamline DM specifications to better serve the common objective of constructing a safe and cost effective ground improvement project.INTRODUCTIONSpecifications should, at their best, convey the project design requirements and provide clear direction to the contractor regarding requirements for submittals, materials, execution, measurement, schedule, and other aspects as necessary. The specifications should not be overly conservative, restrictive or ambiguous, and they absolutely should not be deficient in measurement of quality. Guide specifications or recycled sections from previous projects often form the template for new project specifications. But standards that appear in guide specifications or from former successful construction should be critically scrutinized by the designer for relevance before using the copy/paste functions of the specifications writer’s keyboard. Because work does not always go as smoothly as planned, specifications for remediation of non-compliant construction should be clearly stated and enforced. Often, non-compliancy is reviewed after-the-fact and deemed to have met the design intent, indicating that either the specifications were too restrictive or the enforcement too weak.The Federal Highway Administration Design Manual: Deep Mixing for Embankment and Foundation Support, October 2013, was written by a panel of DM expert design practitioners and contractors. Guide specifications are included as Appendix C of the FHWA manual. Those guide specifications have been updated in the deep mixing section of the www.GeoTechTools.org website, and the updated specifications represent the most complete and authoritative compilation published to date. Although the specifications for DM at www.GeoTechTools.org are current and complete, and they portray the state-ofthe- practice, they too must be modified to fit specific DM applications, project needs, and site conditions. The keys to a good set of specifications are to prescribe construction only to the level that is required to meet the design intent, to require appropriate quality control and quality assurance (QC/ QA) activities, and to clearly address remedial measures required for non-compliant work."

Jan 1, 2015