Search Documents

By S. Pinard, J. MacLellan, G. Ehlert

"The Kidd Creek concentrator is looking actively for alternative technology as means of reducing operating costs in their concentrate handling section. The use of pressure and vacuum filters to eliminate the multiple hearth dryers would have the most beneficial effect. The dryers which constitute the greater portion of concentrate drying costs consume about 35,000 m3 per day of natural gas.After the evaluation of various filters by Kidd's technology group, it was clear that, because of the low final moisture requirements of 5.5 to 6% H20, few filters were able to achieve this target economically. Lately attention has focused on the Andritz hyperbaric filter. Testwork has shown that target moistures can be achieved with an appreciable reduction in operating cost.1.0 INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of Timmins, Ontario. The ore is hauled by the Kidd Creek Railroad to the concentrator where it is milled to produce separate copper and zinc concentrates.Projected concentrator feed for 1991 is 3,750,000 tonnes of ore grading 3.3 % Cu and 4.7 % Zn. The concentrate production is expected to be 458,080 dry tonnes of copper concentrate at a grade of 25.7 % Cu and 265,020 dry tonnes of zinc concentrate at a grade of 54 % Zn.Currently, there is active investigation toward cost reduction through implementation of new technologies. One area which has been extensively evaluated is the concentrate dewatering and drying section. In that section, the multiple hearth concentrate dryers represent the largest source of operating costs, mainly through maintenance and energy costs (electricity and natural gas). The replacement of these dryers with filtration technology that could produce the required concentrate dryness would represent substantial savings.In September of 1990 filtration testwork carried out by Andritz Ruthner showed that Kidd Creek copper and zinc concentrates could be filtered to below 6 and 8 % moisture respectively. In late May 1991 the laboratory testwork was duplicated on siteand one month later a 5 m2 pilot filter was tested on site. Based on the pilot test results, an economic evaluation was performed. It indicated that a reasonable payback could be realized if hyperbaric filters were to replace the existing concentrate drying section."

Jan 1, 1992

By R. S. Simkus, J. R. Egan

"Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant test work conducted in 1990-91 indicated that concentrate grades would be substantially improved by reducing the particle size (P,0) of the lead from 38 to 15 µm and the zinc from 45 to 24 µm.Circuit revisions involved installation of major new equipment including: two GUO kilowatt Vertimills for regrinding, a 4 metre diameter column flotation cell and a 4 metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were reassigned.IntroductionThe Sullivan ore body is a massive sulphide deposit consisting of fine grained mixtures of sulphides, sometimes inter-banded with country rock and varying widely in their content of lead, zinc, iron and silicates. Principal economic minerals are marmatite and galena. Iron is mainly present as pyrrhotite (85%), and to a lesser extent as pyrite (15%) .The orebody has been actively mined since 1923, with 1992 ore reserves estimated at 15,800,000 tonnes with an average grade of 4. 7% lead and 7. 9% zinc. Current plans call for treatment of 1,600,000 tonnes/year, (7,000 tonnes per operating day), with flotation feed grades of 5.9% lead, 10.1% zinc, and 22.0% iron."

Jan 1, 1994

By Peter Wells, Laxman M. Amaratuga, Todd M. Kanhai

"Certain mining methods (eg. Cut-and-fill) result in the contamination of run-of-mine ore with shotcrete. This shotcrete remains mixed with the ore throughout processing. Experimentation performed by Falconbridge Limited revealed that underground contamination of ore by shotcrete (eg. as little as 1% by weight) has led to ill-effects on the nickel recoveries from the flotation process in the mill. The nickel recoveries of contaminated samples were lower than tests without the shotcrete Contamination.To optimize flotation circuits it is important to know why the contamination has created these effects and also to find a method to abate or remove them. Laboratory testing showed that the age of the shotcrete was a factor in it’s effect on nickel recoveries. Younger aged shotcrete gave nickel recoveries lower than baseline nickel recoveries with no contamination. Older shotcrete gave nickel recoveries similar to the baseline.Literature on other cementitious material contaminations on ore revealed that a possible means of remediating this problem is the use of acid in the flotation. The initial pH in the flotation pulp was designed to be pH 9.2, but with the young shotcrete contamination the pH was in the neighbourhood of 10.5. Acid addition may act as a means of lowering the pH to the optimal operational value. Laboratory test work showed that acid addition brought nickel recoveries closer to the baseline."

Jan 1, 2000

By Tim Hughes, A. H. (Sandy) Gray, Jennifer Abols

"The selective recovery of gold and silver from solutions containing other metals such as copper is possible using AuRIX®100 resin in conjunction with the Gekko Resin Column. Selectivity is driven by controlling the solution pH, which enables activities such as loading copper, gold and silver and then selectively stripping copper before gold and silver. Alternatively gold and silver can be loaded and the copper left in solution. The selective loading of gold while reducing the silver loading has also been demonstrated opening the possibility of producing high grade gold doré from high grade silver pregnant leach solutions. This paper reviews the AuRIX®100 resin and Gekko Resin Column Technologies, discusses the uses of AuRIX®100 in the recovery of gold and silver and the chemistry relating to several projects for which AuRIX®100 is being tested.INTRODUCTIONGekko SystemsGekko Systems specializes in the design, development and distribution of innovative mineral processing equipment and systems with a particular focus on gravity separation for the gold and diamond industries. The company, which has been around since 1996, has five main products: the InLine Pressure Jig, the InLine Spinner, the InLine Leach Reactor (ILR), Gekko Resin Column and Modular Systems.The InLine Leach Reactor is an intensive cyanidation reactor that uses high cyanide (0.5 – 2 % NaCN) and high oxidant (20 ppm dissolved oxygen as O2 or hydrogen peroxide) to dissolve gold from medium and high-grade gravity or flotation concentrates. The ILR, which typically replaces a shaking table in the gold room, is available in both batch and continuous models. There are 42 installations worldwide. Further details on this technology can be found in papers written by Gray et al (2003) and Longley, McCallum and Katsikaros (2003). By replacing a shaking table with an ILR, the overall gravity and plant recoveries can be increased significantly. Other advantages include reduced security risks, lower operating costs, reduced operator involvement due to the automatic process and increased safety for gold room operators."

Jan 1, 2006

Operations and maintenance departments have had a long-standing adversarial relationship. The widespread evolution and adoption of modern management techniques, such as reliability centered maintenance (RCM) and Lean, however, has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance and are now adopting Lean throughout organizations. Such modern management initiatives explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in terms of people and methodology. One area that has lagged behind in supporting these developments, however, is information systems. Enterprise asset management (EAM) systems in maintenance and newer manufacturing execution systems (MES) in operations have not been truly integrated in the needed ways. Complicated plants, different software architectures, continually changing conditions and many other variables have led to systems problems, which have contributed to the maintenance/operations divide. Master data synchronization (the plant tree) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology, including web services and service orientated architectures. New technologies are coming on-stream to enable the final bridging of the gap.

Jan 1, 2009

By Martin Kesting

The world wide growth dynamics and the continuously growing demand for energy, results in increasing energy prices. Looking from this point, the efficient exploitation of fossil fuel deposits has become a more important factor to the production of energy raw materials than ever before. This shall be reached by an increase of the automation degree of the bucket wheel excavator in the open pit mining as well as a quality increase of the entire mining process chain. A further optimization of this operation can only be achieved by gathering additional information about the input parameters. The earlier and more exact the description of the input parameter, the greater the effectiveness of the entire process chain. To address this major issue, the RWE Power AG assigned the Institute for Transportation and Automation Technology with the research project "SIMT, Sensory Identification of Material Type and Detection of the Interfaces" [Kes07]. Presently, the control of the bucket wheel excavator is carried out manually by the operator, as well as the visual identification of the different geological layers and the energy raw materials. In this paper, a sensor-system is introduced, which was developed in order to transfer the manual material identification and detection of interfaces into an automatic online procedure. A special challenge and the main focus of this contribution is the integration of this sensor system into a bucket of the bucket wheel excavator. For measuring procedures where direct contact with the in situ material is necessary, the sensor has to be integrated into the bucket. Since direct contact with the material is not necessary, it can be integrated next to the bucket wheel. The results of a preliminary study show that although there is a broad spectrum of sensor technologies for material and interface identification, only a few are suitable for an application in on-line measuring at the bucket wheel excavator. Taking into consideration the demands on the sensor technology, the studies carried out and comparable applications of individual sensor technologies which have already taken place in practice, the integration of the following measuring systems have been realized: ground penetrating radar / reflection measurements, geo electric, resistance geo electric technology. The solution developed in the research project offers for the first time the direct integration of sensor systems into the bucket of a bucket wheel excavator. It will now be possible to test other measurement methods and sensors, not only for the ones already mentioned. As an example the integration of a triaxial accelerometer to measure the solid borne sound and vibrations concerning the cutting of different materials will be shown.

Oct 1, 2009

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

By David R. Skuse, Jacek A. Kostuch, Steven M. Fortier

"Particulate ground calcium carbonate (GCC) is used as a filler and coating pigment in a wide range of applications including papers, paints, plastics and films. In this paper we will overview the requirements for GCC used in both filling and coating applications in the paper industry and highlight the processes used in the production of these materials.INTRODUCTIONCalcium carbonate is both abundant and very widely distributed occurring most commonly as limestone, marble and chalk (Harben 2002). Given, the high purity, whiteness and relative inertness of these materials it is not surprising that they are heavily utilised in a range of industrial applications. Worldwide ground calcium carbonate (GCC) capacity is estimated at 50.5 million tonnes per year (Roskill, 2002). This usage is divided between relatively coarse materials that are used in applications such as landscaping, cultured marble and carpet backing and finer grades that find application in plastics, rubbers, inks, paints and paper. Given the usage of calcium carbonate products across a very wide range of consumer products, the outlook for GCC is very promising with growth expected in many markets. Growth is anticipated across many applications in the emerging nations and more specifically in paper applications on a global basis.Over the last several decades the GCC processing industry has evolved to be well adapted to both the cost effective production and delivery of standard products and the production of high performance speciality products. Many of the standard unit operations found in the metaliferous raw material processing industry are also used, albeit in some cases in modified form, in the processing of GCC. Coarse products (diameter > 3 - 10 µm) are typically produced by dry processing routes. Whereas, the finer products are typically produced by a combination of wet and dry processing."

Jan 1, 2004

By Jerry J. Ran

In open stope mining borehole deviation is one of the main factors affecting the blasting results. Though previous research has identified some actual deviation patterns, these studies are unable to relate the hole deviation pattern with the blasting results and therefore it is not possible to modify the design or take remedial measures based on the prediction of the blasting results. An alternative to the conventional method for borehole surveying is the in-hole probing techniques. With their inherent errors, it is important to evaluate these surveying systems under conditions of different mine sites. The lack of available assessment methods has limited the application of these techniques. In this paper some of the characteristics of the actual hole deviation pattern are discussed based on data from surveying production holes in six stopes. A method of predicting the blasting results is proposed by considering the borehole deviation pattern. Based on the prediction stope design can be modified or further surveying is carried out to improve the blasting results. The tolerable error is introduced to relate the surveying error with the drilling pattern and therefore it is possible to assess various in-hole-surveying techniques.

May 1, 2002

By Paul Staples, Fred Woodcock, Robert Grant, Mike Cooper

"Noranda's Brunswick Mining Division, near Bathurst, New Brunswick, processes 10,500 TPD of complex Cu-Pb-Zn bearing ore. Brunswick uses conventional rod and ball milling techniques to achieve a flotation feed size of 75% passing 400 mesh. Over a two year period, testwork was performed using a Marcy pilot plant ball mill to assess the impact of several key variables on secondary grinding efficiency. Four graded mill charges were used to compare balls and slugs at 25 and 29 mm sizes. Data was evaluated by determining grinding rates using a commercially available steady state simulator. Results were critical in Brunswick's efforts to achieve finer grinds while minimizing cost per tonne.IntroductionBackgroundThe Brunswick orebody is an extremely fined grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite.Size reduction at Brunswick is performed by three separate parallel lines consisting of rod mills, primary and secondary ball mill circuits, all in series. The line 3 grinding circuit is presented in Figure 1."

Jan 1, 1997

By P. K. Frempong, S. D. Butt

"A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine.The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semivariogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates."

Jan 1, 2004

A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine. The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semi- variogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates.

Feb 1, 2004

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By S. Cossio, J. L. Noyola, R. Espinosa

"Minera Penmont’s La Herradura is a joint venture between Industrias Peñoles, S.A. de C.V. and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with a two-stage crushing plant and heap leaching facility. Gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130 000 oz gold per year and its treatment capacity is approximately 22 000 t/d. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to coarse visible gold, which in some cases ranges from 100 to 600 microns.Sampling and assaying protocols were established during exploration and prior to start-up of operations, based on nomographs developed from early heterogeneity tests. However, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block consisting of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to start-up of operations (existing) and the new protocol (leaching). In the existing protocol, sub-sampling is done through riffle splitters, and coning and quartering. Fire assaying was used to estimate the gold content on a 50 g sample. In the leaching protocol, a 12 000 g sample of bottle-rolled cyanide was leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this rotary sampling protocol and for comparison purposes, gold assays were also repeated using the leaching protocol.Test results were compared in three groups: < 0.3 g/t (below cut-off), 0.3 to 0.8 g/t, and >0.8 g/t. Overall, results show that the protocol established prior to start-up of operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2004

By H. Ewaschuk

"INTRODUCTIONRio Algom's Stanleigh Mill in Elliot Lake began production in June of 1983. The highly instrumented mill treats uranium ore at an average rate of 3900 metric tons per day. To help ensure a good start-up and low operating costs, an extensive training program was undertaken prior to and during start-up. This presentation describes how an unconventional operating crew were combined to form an operating unit with a high efficiency in terms of production and labour utilization. I would like to point out at the outset that the operating philosophy, and the role of the supervisors and the operators as set up at Stanleigh is not unique. Indeed, I have seen the same results at a couple of small plants where efficiency meant survival. However, these situations appeared to be the exception, and it was not readily apparent how similar results could be obtained in a larger plant. A factor that existed at the time was low labour turnover. As in most parts of Canada, jobs were easy to get in the Elliot Lake camp in the late 1970's. This, and other factors, contributed to an unusually high labour turnover. This changed dramatically in the early 1980's. Indeed, Rio's two other operating mills, Quirke and Panel reduced crew sizes at this time to reduce operating costs. As a result all of Stanleigh's operators came from Quirke and Panel with experience varying from 4 to 7 years. The experience that operators had was obviously of benefit and served to reduce the scope of the training program from what would have been required with inexperienced personnel."

Jan 1, 1985

By R. E. Michelutti

"The Sudbury area environment became drastically altered commencing in 1871 with lumbering, repeated fires and early open roasting operations from 1887 to 1929. These combined factors had such a pronounced effect that approximately 24 square miles were totally denuded of any vegetation and 87 square miles were semi-barren to somewhat stressed.The two nickel producing companies in the area have reduced the sulphur dioxide emissions considerably over the years. Falconbridge Limited, alone, reduced sulphur dioxide emissions by 77% from 1971 to 1984.These reductions have resulted in improvements to the air, soil, lake and vegetation quality in the Sudbury area.INTRODUCTIONThe Sudbury area environment became drastically altered commencing in the 1870's with lumbering, repeated fires and early open roasting operations from 1888 to 1929. These combined factors had such a pronounced effect on the Sudbury environment that approximately 24 square miles (64 sq. km.) were totally denuded of any vegetation and 87 square miles (225 sq. km.) were semi-barren.Over the years, the Sudbury area environment has improved considerably. This has been due to emission cutbacks by both Inco Metals and Falconbridge Limited, coupled with industry, government and community reclamation programs. Before the improvements are discussed, a better understanding of the historical degradation is required."

Jan 1, 1986

By Jom Kresta

Fundamental changes in the Bitumen Production process at Syncrude have led to the integration of Mining and Extraction operations. Successful operation of the integrated process requires the coordinated effort of several business units. Hence, decision-making has become increasingly more complex and better tools are required. IO2 is a collaborative effort to develop a proof-of-concept prototype of a distributed decision-support system for integrated short-term production and maintenance planning with fleet allocation and dispatching. The prototype includes three main modules (planning, dispatch, and maintenance), a shared database, and a simulation module. At this stage, this prototype is used to plan and operate a simulated mining operation. It is used to demonstrate the viability of the chosen systems architecture and algorithms, as well as the information flows and interactions necessary for improving the overall performance of the integrated operation. While the problem is demonstrated using Syncrude?s site, the methodology is applicable to most integrated resource allocation problems.

May 1, 2002

By M. Massinaei, M. R. Yarahmadi, S. Zeidabadi, M. Oliazadeh

"Although the majority of new flotation column installations continue to be for cleaning or recleaning, an increasing number of flotation projects are specifying columns for roughing or scavenging duties. NICICO has recently installed flotation columns operating in rougher, cleaner and re-cleaner circuits at three new copper concentrators; Miduk, Sungun and Sarcheshmeh. Miduk is probably one of the unique operations that use flotation columns in a rougher circuit. The Miduk rougher circuit comprises five CISA parallel columns. The rougher concentrate constitutes 88% of final concentrate and reports to concentrate thickener. The rougher tailings are scavenged with ten 50 m3 mechanical cells. The scavenger concentrate is then reground and cleaned in three 3.2 m columns in parallel. The cleaner tailings are scavenged in six 50 m37mechanical cells. The cleaner tailings along with the rougher scavenger constitute final tailings.In Sarcheshmeh, the cleaner concentrate is re-cleaned in a column. The column tailings are sent back to the cleaning circuit and the concentrate is reported to the concentrate thickener.This paper reviews performance details of the flotation columns utilized in rougher circuits at Miduk and compares their metallurgical performances in an industrial scale with columns at cleaning circuits for copper flotation. Practical limitations for applying the flotation columns in rougher circuits will be discussed in details.INTRODUCTIONThe use of flotation columns has grown rapidly since the first successful commercial application at Mines Gaspe, where columns were used in a cleaning circuit to float molybdenite. Early applications of columns were restricted to replacing or adding final cleaning stages in existing circuits. Columns can achieve superior cleaning as compared to conventional cells due to their ability to support a large froth depth and the use of water for washing froth. Wash water travels down through the froth and crosses the pulp/froth interface, replaces the entrained particles reporting to the froth from pulp and improve the concentrate grade."

Jan 1, 2011

By R. Venugopal, Saxena. V. K., U. Sankrityayan

"There is a dire need of a technology which can break the mineral interfaces to enhance liberation with minimum energy consumption in mineral beneficiation processes. Understanding of mineral crystal system and interfaces is essential to develop such methodology. So, this study is carried out to find out the role of mineral crystallography in milling and liberation. Data related of mineral crystallography, Vickers Hardness Number, Bond Work Index and beneficiation processes were collected from literature and detailed statistical analysis has been carried out to establish a correlation among these parameters. It was found that atomic weight and cell parameters shown statistically significant relationship with Vickers Hardness Number of minerals, which controls the milling characteristics of ores. Liberation characteristics of five different kinds of ores were analyzed considering the types of interfaces between valuable and gangue minerals. It was found that phase interfaces play vita role in liberation and coarser liberation can be achieved in the minerals of incoherent crystal systems like manganese and zinc ores. Study of this subject can help us to understand the effect of stress wave propagation in solids and its effect on crystal interfaces. It can also help us to design a technology of future to break the mineral interfaces.INTRODUCTIONCommunition is energy intensive mineral processing operation and consumes up to 2% of the total electric power generated in the world. Energy consumption due to comminution is increasing every year as there is growing needs to exploit lower grade ore bodies and process rejects (Blazy et al., 1994; DOE, 2005). Low grade ores require crushing and grinding to liberate the valuable minerals which are further separated from gangues by various beneficiation methods like gravity separation, floatation, leaching etc. Currently, comminution methods are selected based on the reduction ratio and energy consumption but effect of grinding methods on subsequent processing methods specially on liberation also need to be studied to optimize the entire beneficiation process. Most of the attempts made in past to minimize the energy consumption in milling to enhance the mineral liberation were focused on compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Kilpelm and Austin, 1982; Norgate and Weller et al, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang el al., 2011; Singh et al., 2012). But the role of mineral crystallography on milling and liberation behavior of minerals not fully explored yet."

Jan 1, 2013

By Richard Burt

"In seeking to supply the ever increasing needs for raw materials, the mining industry has been required to develop lower grade resources in increasingly remote regions of the world. This has resulted in the extension of many frontiers, both technologically and geographically.The accent of mineral processing research over the last few decades has been to “do existing things better”. There have been many breakthroughs in equipment and processes; however in general the accent has been to increase capacity of existing unit processes, often by orders of magnitude, or to refine the process itself by basic research and development. This has lead to added sophistication, enabling the process engineer to maintain optimum performance of his equipment while reducing the cost, and the amount of labour needed to operate the plant.While much of the increased requirement for resources is handled by the development of ever larger, lower grade orebodies, a significant portion still comes from the small miner - even the artisanal miner - operating in remote and often politically sensitive parts of the world. For them, innovation and simplicity are the keys, not sophistication.The tension between sophistication and simplicity - or research and reality - is specially evident in the area of gravity concentration of rare metals, such as tin and tantalum. This paper looks at this tension, primarily from the eyes of an operator and seeks to put into perspective the two paradigms."

Jan 1, 1999