Search Documents

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By V. A. Akinbinua

This work is intended to examine the relationship between rock fragments produced during compression tests using a soft testing machine, e.g. hydraulic press (the machine used in this work is Amlser rock testing machine), and the rock fragments size distribution produced by fragmentation of the same rock through application of explosive. The rocks tested are fine grained marble, medium grained tonalite and fine-medium grained granite, medium grained norite and medium grained gabbro. The rocks types are prepared according to ISRM methods to be tested for strength determination. The rocks are loaded at constant load until failure. The fragments resulting from the failure of each of the rocks types are collected for size characterization by sieve analysis. The same rocks tested under soft testing machine are also prepared into blocks of dimension 150 mm length x 100 mm width x 100 mm height for blasting by explosive application. Each block of the different rocks are drilled through with an 8 mm diameter drill to a depth of 80 mm. Each of the holes on the blocks is spaced from each other at 44.7 mm and with a burden of 28 mm. The holes therefore formed a rectangular blasting pattern. Each of the holes was charged with a 720 mg electronic detonator and fired instantaneously inside a cylindrical blasting chamber. After each shot, the fragments are collected for size characterization. The sizes distributions from blasting are compared with sizes distributions resulting from rock testing using the parameter Xc of the Rosin-Rammler distribution function (RR) and 75% cumulative percentage passing. The analysis and finding from this work is presented in this paper.

Jan 1, 2014

By R. D. Williams

In spite of the increasingly polarized and politicized view of climate science and climate change in the United States, many of the principles behind the ?theory? of Anthropogenic Global Warming (AGW) or Global Climate Change (GCC) are in fact firmly established both in fundamental physics and detailed observations and are widely accepted elsewhere. The discovery of the earth?s ?greenhouse effect? dates back nearly 200 years to the work of French mathematician and physicist Joseph Fourier in 1824 and 1827. In 1872, John Tyndall an English physicist and mountaineer, described the capacity of various gasses to absorb radiant heat. He identified water vapor and carbon dioxide as the principal ?greenhouse? gasses. The work of Fourier and Tyndall was the foundation for the theory that increasing carbon dioxide (CO2) in the atmosphere might be responsible for an increase in global temperatures developed by the brilliant Swedish chemist Svante August Arrhenius in 1896. This was backed up by the additional work of Gilbert Callendar in the 1930s, and Gilbert Plass, Hans Suess and Roger Revelle in the 1950s. There is little scientific dispute about the physics by which this occurs: carbon dioxide in the atmosphere absorbs long wave radiation that would otherwise escape into space, thus warming the lower atmosphere and respective temperatures worldwide. The Intergovernmental Panel on Climate Change (IPCC), approximately 2500 climate scientists from around the world, has concluded that increases in carbon dioxide resulting principally from the burning of fossil fuels are responsible for most of the continuing increases in global temperatures (IPCC, 2007). NASA?s Goddard Institute for Space Studies (GISS) states; ?The ten warmest years all occur within the 12-year period 1997-2008? (GISS, 2009). 2009 was the second warmest year on record and 2010 was tied with 2005 for the warmest year on record (GISS, 2010, 2011). The science is in fact settled; the earth has not cooled since 1998 as some have claimed. It continues to warm as evidenced by not only surface temperature records but also ocean temperature records as well as changes in physical and biological systems (IPCC, 2007).

Feb 27, 2013

By J. Utt

Recent developments in circulating fluidized bed (CFB) once-through supercritical technology (OTSC) have enabled this technology to be offered as a utility-scale alternative competing head-to-head with pulverized fuel (PF) OTSC offerings. One clear example is the CFB supercritical unit at the Lagisza Power Plant in Poland, owned by PoludniowyKoncernEnergetyczny SA (PKE). This unit has now been in commercial operation for three full years, exhibiting very good performance, and has validated Foster Wheeler?s performance model at this utility scale as well as for units in the 600 MWe and 800 MWe size ranges offering net efficiency of ~43 per cent (LHV basis). This operating unit has also proven the use of the world?s first FW/BENSON? vertical-tube OTSC low mass flux technology. Since the Lagisza original international tender specified OTSC PF technology, it is important to note that the alternative selection of CFB OTSC technology over conventional PF technology is of historic significance, not only for the validation of the CFB supercritical platform as a viable alternative to conventional PF technology, but it also positions the CFB OTSC with fuel flexibility for offering of sizes up to and including 800 MWe units. This paper explores the differences between CFB OTSC technology and standard PF OTSC in utility power generation. Selection criteria, fuel burning range in both technologies, and other selection drivers are discussed. Economic analysis of both technologies, based on existing cases, is also provided. Also discussed are the technical advantages and uses of each technology. Foster Wheeler has recently been awarded a contract for four units of CFB OTSC technology, which utilizes a 2 on 1 configuration of two 550 MWe CFB OTSC boilers on two single 1000 MWe turbines. Essentially this provides a fuel-flexible low-emissions alternative to a 2 × 1000 MWe solid fuel power block.

Jan 1, 2012

By Isaac Minaya, Jhonny Torre, Mario Carpio, Jesús Fuentes

El litio se considera un elemento estratégico debido a sus diversos usos en industrias tales como la electrónica o la automotriz. Por ello, se debe entender cuáles son los ambientes geológicos (pegmatitas, ambientes volcánicos, ambientes metamórficos y cuencas endorreicas en relación a salares y salmueras) asociados donde alberguen los minerales de litio (silicatos, sales y/o salmueras). Para llegar a ello, se deben conocer las características macroscópicas geológicas de campo y fundamentar su interpretación por medio del apoyo de la instrumentación en los tipos de análisis químicos, mineralógicos, las características microscópicas petrográficas y la caracterización puntual de algunas muestras por la microscopía electrónica de barrido (SEM). Por tanto, en esta publicación se presentan datos preliminares de ocurrencias con valores anómalos de litio en afloramientos de rocas volcánicas, intrusivas (graníticas), aplíticas y metamórficas dentro de las unidades morfo estructurales del Altiplano y la Cordillera Oriental, ubicadas en las regiones de Cusco y Puno. En la zona de Corani (Puno) afloran rocas volcánicas tipo tobas de lapilli con altos contenidos de litio entre 2815 a 3070 ppm, cuya presencia se relaciona a los minerales de micas de litio, denominado lepidolita, como constituyentes inmersas en agregados granoblásticos de cloritas y silicatos, perteneciente al miembro Sapanuta de la formación Quenamari. Por su parte, en la zona de Ocongate (Cusco) las ocurrencias con anomalías de litio (1096 ppm) se encuentran asociados en clinocloros y/o amorfos asociados como constituyente dentro de cuerpos de areniscas, con presencia de vetas de cuarzo, sulfatos de cobre, óxidos de hierro, trazas de pirita y calcopirita, pertenecientes a la formación Ananea.

Sep 20, 2019

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

By Alain Blanchier, Gilles Gomez

Neighborhood pressure on quarries has become urgent to deal with quarry managers and operators must apply the most recent technologies and communicate it for long shelf life time exploitation, the quarry in which the work is located in urban or suburban environments needs to take into account blasting rules as well as site environment. The main problems to be addressed are:

Jan 1, 2009

By N. Charue

An international prediction event was carried out within the framework of a 30-pile testing program organized in a sandy soil in Belgium (Limelette). That program called upon sev­eral testing methods: static load tests, Statnamic testing, and dynamic testing. This paper provides a summary of received predictions and results obtained from the static pile load tests, which were carried up to failure of the instrumented piles. The comparison between predictions is made using load-settlement curves with reference to the results of the static load tests. The predictions are based on a geotechnical approach using an extensive soil investigation program and a dynamic approach using the dynamic load test data.

Jan 1, 2002

By P. W. Godbehere

"INTRODUCTIONMagnetic mill linings have been developed from an invention by Mr. Bertil Brandt, the originator of the Skega rubber lining. The OREBED magnetic mill lining is a concept in which rubber covered strontium ferrite permanent magnets are arranged on the inside wall of a mill shell so that they attract magnetically susceptible material be it ore, media or tramp, to form a protective layer over the magnets and to serve as an operating surface with indefinite life.Noranda Mines Ltd. through its associate Norcast Division of Noranda Metal Industries formed a joint venture with the inventors to market magnetic mill linings in North America. For the past twelve months trials have been undertaken in conjunction with Orebed Inc. to test and develop these linings for grinding mill applications at the Horne Concentrator. Two independent milling circuits are currently being operated, one treating a siliceous gold ore and the other a copper slag.This paper presents the results of the magnetic lining test programme to date."

Jan 1, 1983

This paper summarizes the progress of geological exploration at North Broken Hill Ltd.The North Mine orebodies occur in knots of minor folds on a simple limb structure which is itself highly folded, giving rise to two distinct orebodies pitching N. at av. 42° down to 2,920-ft. level, where the pitch steepens to near vertical as a result of complementary shear movement on the Globe-Vauxhall Crush Zone.The lack of adequate marker beds and top and bottom relations makes the resolving of the complex structural environment of the orebodies most difficult.To test the deeper ground of each side of the De Bavay Fault on the 2,600-ft. level the footwall drive was extended 3,556 feet and over 20,000 ft. of drilling completed from three transverse fans, only one of which intersected the orebodies due to steepening of pitch.The problem of locating the North Mine orebodies N. of the DeBavay Fault remains speculative because the exact position of them S. of the fault is still unknown. Exploration beyond the fault in the search for ore had two lines of mineralization to consider, an eastern one through Cosgroves-Round Hill, long regarded as the continuation of the main lode, and a western one passing through Silver Hill Silver Peak.From surface 45,000 ft. of drilling was completed in five sections, establishing that the structure was dominantly synclinal with a flatdipping E. limb, the W. limb and adjoining structures being involved in the Globe-Vauxhall Crush Zone. Mineralization, though weak, was remarkably persistent but the economic mineralization exposed at surface has not persisted with any continuity.Deep exploratory drilling below the bottom level (3,370 ft.) has established high-grade ore to a depth of 4,095 ft. and also has proved its existence within the Globe-Vauxhall Crush Zone.INTRODUCTIONThis paper summarizes the progress of geological exploration at North Broken Hill Limited from the inception of the Geological Department in 1941 until the end of 1955. The writer has drawn freely on departmental records for the period prior to 1947.

Jan 1, 1956

By Peter Fischer

Between 45,000 and 50,000 claims for subsidence are submitted each year to the German hard coal industry. In order to improve the service to claimants a quality management was established in 2005. This paper describes the process now used for handling these claims. A quality check has also been carried out by way of a customer survey, which was performed by an independent research agency. The results of the survey are presented in this paper. In Germany, research into mining subsidence mainly involves the prediction of ground movements caused by deep mining operations. Special areas of research are subsidence reducing aspects of the extraction panel planning, especially from the point of view of mining dynamics, as well as securing and restoration measures. This work seeks to prevent or minimize mining-induced damages close to the surface, for instance, buildings or infrastructure installations (such as pipelines), or underground mine openings (e.g. shafts). Roof collapses and surface fractures caused by shallow mine workings of an earlier era currently constitute a special area of investigation.

Jan 1, 2006

By Hernando Valdivia

La compañía minera Antamina tiene doce años de operación, los cuales han significado un esfuerzo para la concentración y separación de minerales de cobre, zinc, molibdeno y plomo-bismuto. Sin embargo, es necesario elaborar un plan de minado donde se resuevan problemas como: leyes de cabeza de alta variabilidad, transición y alteración litológica, brechamientos mineralizados y no-mineralizados, cuerpos intrusivos de baja ley, zonas de enriquecimiento y oxidación, entre otros. En este sentido, el presente texto describe una alternativa al procesamiento de minerales oxidados de cobre que responda al plan de producción 2013 en la compañia minera Antamina. Así, la alternativa de utilización de stockpiles con mineral de baja ley de cobre se presenta como una de las más viables donde se obtuvo resultados metalúrgicos favorables, los cuales permiten reemplazar la fracción de mineral Usupallares con el uso de stockpiles muy antiguos. Así también se realiza blending de minerales de Usupallares en proporción de 25% y 50% con minerales transicionales tipo cobre bajo molibdeno, de altos contenidos de bismuto, para mejorar la flotabilidad de este.

Sep 21, 2013

By H. Zhu

Coal desulphurization by flotation is often difficult due to the surface oxidation of coal pyrite. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were adopted to obtain detailed information about the surface oxidation of pyrite. Fresh pyrite surfaces were found to be hydrophilic, and to turn hydrophobic after initial oxidation, with oxidized products such as polysulphide FeSx and free sulphur. The oxidized products on the pyrite surface were reduced by an electrochemical method, returning the surfaces to a hydrophilic state and thus increasing the separating efficiency of coal from pyrite by flotation. Key words: surface oxidation, pyrite, SEM, XRD pattern, electrochemical modification.

Jan 1, 2002

By M. Kumral

A mining system consists of many sub-systems such as drilling, blasting, loading, hauling, ventilation, hoisting and supporting. During mining operation, these sub-systems may experience various problems that stop the operation because of possible environmental equipment and safety issues. In order to ensure delivery contracts in the required quality and safe mining medium, the operation should be, at least, performed in the specified reliability level of the system. If the system reliability decreases below the specified level, there will be safety and financial losses for the mining company. Therefore, the mine should be maintained by a reconstruction procedure to guarantee the operation continuity. Given that each sub-system has a different reliability function and maintenance cost, the determination of reconstruction time will be a complicated decision making problem. In this paper, the determination of reconstruction time is formulated as a nonlinear optimization problem and solved by genetic algorithms (GA). A case study was conducted to demonstrate the performance of the approach for an underground operation. The results showed that the approach could be used to determine the best action time. Keywords: mining system; genetic algorithms; reconstruction time; reliability analysis

Jan 1, 2009

By S McKinley

"The White Mountain sediment-hosted gold deposit is located in north-eastern China. Mineralisation is associated with silica–hematite–altered polymict breccias that occur within dolomite at or near the contact with overlying sandstone. Economic gold grades are controlled by the distribution of the polymict breccias and can transition rapidly to low or zero grade over short distances. This results in sharp and highly irregular ore contacts on whose accuracy proper stope design and ore control is reliant at this blasthole underground mine.Short-term planning and ore control utilise a grade control model created from infill drilling and grade control sampling (ie face and wall sampling). Typically, the grade control model was maintained by time-consuming manual editing of earlier made contacts to incorporate any new data. This approach also was quite error-prone due to: the complexity of the breccia and ore grade contacts irregularly oriented and/or insufficiently dense drill holes inconsistent incorporation of grade control sampling. These errors resulted in unplanned dilution and ore loss due to inaccurate interpretation of the ore contacts.The primary advantage to implicit geological models over conventional, manually-built wireframe models is that they can be updated very quickly and frequently. In a mine setting, the power and efficiency of using an implicit model is greatest where the use of manual inputs or editing can be minimised. Recently a workflow was set-up for the mine geology team to create an implicitly-modelled ore shape for short-term planning needs by using all data, especially all grade control samples. The resultant 3D shapes provided metre-scale accuracy and consistently reconciled complex ore geometries much faster and to a higher degree of quality relative to the wireframe model. The mine stakeholders can now obtain an accurate ore model that will always be in sync with available data.CITATION:McKinley, S, 2017. Application of implicit geological modelling to improve the grade control process at White Mountain gold mine, Jilin Province, China, in Proceedings Tenth International Mining Geology Conference 2017, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By A. Demirag, F. Burat

"The most important metals in the jewelry sector are undoubtedly gold and silver. As a result of workmanship work done in the jewelry industry, the tiny metal and jewel fragments and metallic powders are scattered. Given the prices of gold and silver on the market, the dust that emanates from these workshops is of great importance. Gold recycling has become as important as raw material production within the mass market and gold production industry. In 2016, 29% of the world gold supply has been obtained through recycled gold production. Waste derived from jewelry activity is included in this category, and represents an essential component of this percentage. In the scope of this study, the recovery possibilities of Au and Ag from jewelry sweeps floor sample was investigated using flotation method. In the experiments, optimum pH value, particle size, the effect of dispersant, type and amount of reagent were investigated. As a result of these studies, it was determined that the optimum pH value was 6.5 and the particle size was -212 microns. It was observed that the most suitable reactive combination was Aero 242 and Aerophine 3418A and Na2SiO3 has no positive effect on recovery of Au and Ag as a dispersant agent. As a result of tests, a final concentrate containing 268 ppm Au and 2122 ppm Ag was obtained with 81.4% and 74.5% recovery respectively. INTRODUCTION Because of the softness of pure gold, it is usually alloyed with base metals for use in jewelry, altering its hardness and ductility, melting point, color and other properties. On the other hand, gold has some special chemical properties which in normal conditions, don’t react with water, dry or humid air, oxygen, ozone, nitrogen, hydrogen, fluorine, iodine, sulfur and hydrogen. In these days, gold is used in different sectors like jewelry, electronics, finances and investing, dentistry, medicine, aerospace, awards & status symbols. According to Deutsche Bank Research, the primary usage of gold is jewelry. It has been used to make ornament and jewelry for thousands of years. In this sector craftsmen learned that alloying gold with other metals like copper, platinum and silver to increase gold’s durability. Alloying gold with other metals changes the color of the products. Another significant sector of gold is electronics. Modern electronics want the use of noble metals, like gold, especially in the areas of information processing, telecommunications, and military and space electronics (Habashi, 1997). Electronic devices use very low voltages and currents which are easily interrupted by corrosion or tarnish at the contact points. Gold is the highly efficient conductor that can carry these tiny currents and remain free of corrosion. Electronic components made with gold are highly reliable. Gold is used in connectors, switch and relay contacts, soldered joints and connecting wires. Every sophisticated electronic device have a considerable amount of gold. This includes cell phones, calculators, personal digital assistants, GPS units, and other small electronic devices. Most large electronic appliances such as television sets also contain gold. Humankind has known silver since prehistoric times like gold because silver occurs in native form. The metal is found in the Earth's crust in the pure, free elemental form native, as an alloy with gold and other metals, and in mineral such as argentite. Most silver is produced as a byproduct of copper, gold, lead, and zinc refining. Silver is very soft metal like gold also, it is the highest electrical conductivity, thermal conductivity, and the lowest electrical contact resistance of all metals (Habashi, 1997). Silver is used in different sectors like industry, jewelry, electronics, photography silver good, and coins. The main usage of silver is supplied by electronics. Silver's unsurpassed thermal and electrical conductivity among metals means it cannot easily be replaced by cheaper materials. In addition to silver is using in ener"

Jan 1, 2018

By Hamed Khodadadi, Hamid Ghadiri

In this study, a fuzzy logic self-tuning PID controller based on an improved disturbance observer is designed for control of the ball mill grinding circuit. The ball mill grinding circuit has vast applications in the mining, metallurgy, chemistry, pharmacy, and research laboratories; however, this system has some challenges. The grinding circuit is a multivariable system in which the high interaction between loops, the variation of the system parameters with time, and time delay are some of the problems that pose a challenge. Since the controller parameters are determined offline in classic PID control, these gains are unchangeable and cannot overcome the mentioned challenges in this system. Hence, a fuzzy logic self-tuning PID controller, which is a combination of fuzzy logic and a conventional PID controller, is proposed to control the grinding system, especially in the presence of model mismatch and disturbances. In addition, in order to solve the system challenges, a multivariable control approach based on an improved disturbance observer is proposed to suppress the effects of the disturbances. The most important feature of the algorithm proposed in this paper as the combination of fuzzy logic self-tuning PID and improved disturbance observer is its ability to eliminate system interaction, attenuate internal and external disturbances, and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit. Simulation results in the cases of the set-point change in particle size and circulating load in the presence of model mismatch and external disturbances confirmed the controller performance compared to other controllers.

By Hamed Khodadadi, Hamid Ghadiri

In this study, a fuzzy logic self-tuning PID controller based on an improved disturbance observer is designed for control of the ball mill grinding circuit. The ball mill grinding circuit has vast applications in the mining, metallurgy, chemistry, pharmacy, and research laboratories; however, this system has some challenges. The grinding circuit is a multivariable system in which the high interaction between loops, the variation of the system parameters with time, and time delay are some of the problems that pose a challenge. Since the controller parameters are determined offline in classic PID control, these gains are unchangeable and cannot overcome the mentioned challenges in this system. Hence, a fuzzy logic self-tuning PID controller, which is a combination of fuzzy logic and a conventional PID controller, is proposed to control the grinding system, especially in the presence of model mismatch and disturbances. In addition, in order to solve the system challenges, a multivariable control approach based on an improved disturbance observer is proposed to suppress the effects of the disturbances. The most important feature of the algorithm proposed in this paper as the combination of fuzzy logic self-tuning PID and improved disturbance observer is its ability to eliminate system interaction, attenuate internal and external disturbances, and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit. Simulation results in the cases of the set-point change in particle size and circulating load in the presence of model mismatch and external disturbances confirmed the controller performance compared to other controllers.

By O. A. Bascur

The lack of integration of mining and metallurgical information with sufficient detail for analysis causes inefficient operation and hence sub-optimal energy and water use. It is difficult to analyze the performance of mining and metallurgical processes without an integrated view of mine transactions, stockpile inventories, process flows and assays. To take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. This paper presents an infrastructure with advanced tools that sift through available data, identify and eliminate gross errors, and transform the data into business information for continuous improvement and optimization. Collaboration is a key component of improving efficiency of energy and water use, and the evolution of Web technology enables collaboration and troubleshooting of plant information to more quickly act on issues to reduce wasteful operation. Keywords: Mine Concentrator Optimization, Real Time Performance Management, Data Unification, Integration of Operational and Business systems, Mass and Energy Balances, Real Time Web Services, Equipment Availability, Efficiency.

Jan 1, 2009