Search Documents

By D. Xie, S. Sun

An overview of recent development of CSIRO?s Multi-Phase reaction models will be presented with examples comparing the calculated physico-chemical properties of metallurgical slags with the existing experimental data. The paper will also outline the development of a kinetically based model for molten bath reactors and its application to submerged combustion of coal in a slag bath as well as the reaction between the slag and injected coal particles. The plume model combines established models for the combustion of pulverized fuel with models for the growth and rise of bubbles from a lance or tuyere. This model predicts the extent of de-volatilization and combustion of the coal in the plume, the utilization of oxygen and the exchange rate of oxygen between the gas and the bath as well as the heat transfer rate between the gas bubbles and the bath. The slag reduction model brings together the recently measured rate data and fundamental understanding of the kinetics of CO-CO2reaction with iron oxide containing slags and predicts the changes resulting from injection of coal particles into molten slags. The top-space model covers reactions between gases and molten droplets in the post-combustion zone, where heat and mass transfer between phases results in higher utilization of the fuel values in the partly oxidized gases and transfer of heat to the molten bath. Keywords: Phase equilibria, viscosity, electrical conductivity, slags, kinetics, reaction rate.

Jan 1, 2004

By J. T. McLendon

As part of its research project in developing improved refractory materials for metallurgical applications, the Federal Bureau of Mines obtained hot modulus of rupture data at 1,500°,1,550°, and 1,600° C on samples of 13 refractory periclase materials produced from seawater, lake brines, and natural magnesite. The periclase samples also were characterized to establish chemical and mineralogical composition and microstructure. The results indicated that a high MgO content does not necessarily assure good hot strength and that an optimum and varying CaO-Si02 ratio exists for each individual periclase sample.

Jan 1, 1979

By Kazimierz Gwizdala

In recent years, in Poland the ATLAS piles have been successfully applied for some constructions near Gdansk. The piles have been used as foundations for housing and another areas of civil engineering, in delta Vistula geotechnical region, characterized by weak, highly compressible soils represented by mud and peat, lying in sub-surface layers, several meters thick. Usually below are dense sandy soils or gravel. In all cases, the base of ATLAS piles rested on sandy soils. The analysis of pile bearing capacity has been discussed and verified by static pile load tests (SPLT). The load-settlements characteristics obtained were satisfactory. In the paper, the results of geotechnical investigations as well as calculations and load tests are shown. The ecological aspects of ATLAS piles application within highly urban areas of the cities and complex geotechnical conditions are emphasized.

Jan 1, 2006

By Erich U. Petersen

Recognition of mineralogical and chemical zoning patterns associated with mineralization is an integral part of mineral exploration. Even though the origin of zoning may not always be known, zoning patterns as expressed by the systematic distribution of ore and gangue minerals, alteration or elemental assays (soil and rock geochemistry) have received much attention and are extremely useful in guiding exploration efforts toward locating economic mineralization. By contrast, the potential of using zoning information recorded in solid-solution minerals to address practical geological-engineering problems has received less attention. Solid-solution minerals can provide critical information for common problems faced in exploration, mine development and valuation. Mineral zoning information from solid-solution minerals can now be easily obtained because advances in electron microprobe instrumentation have made these instruments a most efficient, accurate, economical and practical tool for analysis of large numbers of samples. Now entire mines and districts can be studied in a timely and cost-effective manner as required by modern mineral exploration and mining practice. This article shows how knowledge of the composition of fahlore minerals can be used in addressing important problems in exploration, development and valuation. Situations are described in which drilling intersected "low grade zones" (Case one: Orcopampa, Peru, precious metal system) and where there was a need to determine the "lateral correlation of multiple ore intercepts" (Case two: Sheep Creek, Montana, sediment-hosted sulfide deposit).

Jan 1, 1992

By Thomas Donnelly

Introduction THE Province of San Cristobal is situated on the south side of the island of Santo Domingo about 25 miles west of Santo Domingo city, the capital of the republic. The copper mineralization is found about 1.-CAMP BUCARO. THE TOP OF THE RIDGE IN THE BACKGROUND MARKS THE CONTACT OF THE LIMESTONE AND TUFFS. S miles north of the town of San Cristobal, in the section known as Bucaro Hill; in San Francisco Hill; on the Nigua River; and on the Jaina (Liver. The district is reached by automobile from Santo Domingo city over an excellent road for 25 miles to San Cristobal, and then, by horse-back 6 or 8 miles up the Nigua River to what is locally known as "Camp

Jan 8, 1915

By Winfried Rosenstock

The development of electronic initiation systems has partially reached or will reach in a short period of time full reliability for general use without limitations. Unfortunately those systems meet with a fully unprepared mining community and is confronted worldwide with blasting procedures which are not suitable to exploit the full range of the electronic option. This is for the time being only belonging to quarrying and general surface mining, for the use in underground operations the detonator is still not yet competitive, apart from special cases. It is not to be taken in doubts that the introduction for underground purposes will follow in a less shorter or longer period of time.

Jan 1, 2003

By John A. Wells, Leticia Conca, Kenneth G. Thomas

"Since about 2002 there has been significant capital cost escalation, not inflation, in the mining industry causing turmoil for successful project completion. Project capital costs have more than doubled and some cases tripled in this time period. This has rendered many projects to be economically challenged and in some cases not viable. In addition higher than expected operating costs have further adversely affected project metrics such as NPV and IRR. Capital cost increases for projects have been widely reported globally. This current paper reviews three items. Firstly, why such capital increases and the various components that make up capital estimates. Secondly, it looks at reasons why preliminary estimates, for example at scoping and pre-feasibility level, have been lower than the ultimate constructed costs. Such increases and differences in estimates have caused major problems for mine builders and have led to a general nervousness on the part of those providing project finance. Thirdly, what discipline is needed in project execution in an attempt to mitigate such capital increases. The paper will hopefully give a better understanding of the various issues and factors involved for those in the mining industry.INTRODUCTION The years 2012 and 2013 were a turbulent time for the mining industry. The European economic crisis, politics, metal price volatility and a wave of changes of CEO´s in some of the major mining companies all contributed to a challenging couple of years. Two issues stood out. First, the huge increases reported in the capital costs of projects, where increases of 100% - 300% were not uncommon and in some cases exceeded that during the first decade of the 21st century. Second, company write downs related to takeovers during the boom and the stabilization/correction in commodity prices. These have led to great uncertainty, made it difficult (or impossible) to raise project financing costs, contributed to the changes at CEO level and placed many projects either on hold or cancelled altogether. It is commonplace now to read of companies talking of reduced capital expenditure and making a complete review of their projects and operations to contain costs."

Jan 1, 2014

By Steven A. Mathe, Seokbin Lim

Current analytical models can accurately predict the final velocity of explosively driven flyers and can somewhat predict the acceleration profile, but do little to address the deformation of the flyers. Explosive systems such as linear shaped charges and explosively formed projectiles, which can be described as multiple interacting explosively driven flyers, often involve interactions between the flyers that occur much before the flyers reach their predicted final velocity. In this regime, it is important to accurately understand both the acceleration profile and the deformation profile of the flyers, as both significantly affect the functioning of the explosive systems. Previous work proposed an analytical model to meet this need. As the expanding gas cloud of detonation products drives the flyers, rarefactions impinge upon the gas cloud from around the flyer edges, which produces a pressure difference across the back face of the flyer leading to deformation of the flyer. Previous research condensed the effects of the rarefactions into a single term, the pressure release ratio, ?, which was calculated based on hydrocode simulations of a block of explosive only and an assumption of isentropic expansion. This work intends to determine the value of ? for different explosive compounds. The results of this analysis were compared to hydrocode simulations of an open-faced sandwich configuration explosive/flyer system with an average accuracy of 15% across the tested compounds.

Jan 1, 2015

By Tadeu Messias Donizete Borba

A soldagem com elevado aporte térmico é uma das alternativas adotadas pelos estaleiros para aumento da produtividade nas operações de união de materiais. No entanto, os ciclos térmicos gerados durante a soldagem podem provocar transformações microestruturais prejudiciais à tenacidade na zona afetada pelo calor (ZAC). Este estudo teve como principal propósito realizar a caracterização microestrutural e avaliar as propriedades mecânicas da ZAC do aço naval Sincron EH36 produzido na Usiminas por laminação controlada seguida de resfriamento acelerado em comparação com um aço de mesma classe de limite de escoamento produzido convencionalmente, ambos soldados pelo processo ao arco submerso em dois níveis de aporte térmico: 76 e 130 kJ/cm. Foi observado que a presença de uma microestrutura mais refinada nas diferentes regiões da ZAC, associadas ao menor tamanho de grão do metal base e ao menor carbono equivalente, foram os principais fatores que contribuíram para a excelente tenacidade da ZAC do aço Sincron em comparação ao aço convencional. Os resultados obtidos mostraram que é possível obter juntas soldadas com excelentes propriedades mecânicas ao se empregar aço Sincron para a soldagem com altos aportes de calor, e sua utilização pode ser uma estratégia para otimização dos tempos e custos de fabricação na indústria naval.

Aug 8, 2018

By A. L. Worthen

This is one of a series of pacers being published by the United States Bureau of Mines, describing mining and milling methods at crushed-stone plants throughout the United States. These pacers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. Although the publication of total production cost might not be advisable in some instances, yet a knowledge of operating costs is essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called o this differentiation in order that there will be no misunderstanding of the scope of the cost tabulations. This paper deals with the quarrying and crushing methods used at the Plainville plant of the New Haven Trap Rock Co., which produces annually between 275,000 and 300,000 tons of trap rock, Although pct the largest quarry operated by the company, it typifies the standard methods used by all the quarries in producing crushed stone and has one or two rather unique operating features. The cost of production at this plant is close to the average cost at all quarries of the company.

Jan 1, 1936

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975

This is the seventh in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covering 1,875 samples represents the products of 83 companies plus those from the Pacific coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. For the regular grade 985 samples consisting of 73 different brands are averaged. The premium grade consists of 489 samples of 40 different brands. The third grade has 401 samples averaged from 51 different brands. In this report the districts have been reduced to 21 by combining North and South Texas into one district. Fl Paso samples are reported with the South Rocky Mountain district, and Amarillo, Tex., has been included with the Middle Rocker Mountain district. In the present survey samples from Fort Smith, Ark., have been included in the Tulsa area, Indianapolis has been included in the St. Louis district. Cleveland represents the State of Ohio. Samples from Little Rock, Ark., and North Carolina have been included in the Memphis district. The Pittsburgh district includes samples only from this State and Wheeling, W. Va. The actual sampling points in each area are indicated an table 1.

Jan 1, 1939

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Lutz Markworth, Evren Ören

"The worldwide demand of ores and the depletion of the high-purity deposits make it necessary to recover ores in increasingly finer size fractions in the feed material. The flotation technology of more than 40 years old plants was not able to recover the ultra fine material. Those slurry tailings ponds now have the chance to be re-processed with PNEUFLOT® technology.The bubble sizes of different flotation technologies have a huge influence of the results especially regarding the recovery of the ultra fine particle sizes.PNEUFLOT® technology of HUMBOLDT WEDAG Coal & Minerals Technology GmbH in Germany was applied to ultra fine Phosphate, Copper and Platinum ores. The results will be presented in this paper.Conventional technology like agitator flotation has its limits in the flotation of fines due to turbulences in the cell. The position of the agitator influences the recovery of the fines. A deep impeller generates a higher froth zone. This helps to catch the medium fines. Due to the static head of the slurry inside the cell, compressed air is required for such cell designs.Column flotation is well known for a good selectivity without having in the first cell a good recovery. This leads to invest in several cleaning stages to reach an acceptable recovery. Further more, compressed air is required to generate the air bubbles to the flotation process, which are much bigger than with PNEUFLOT® technology applied.INTRODUCTIONHigh metal prices are actually the basis to invest in poor deposits or deposits with very fine intergrown ores which have to be milled down to ultra fine powders less than 60 micron. The liberation grade has to be determined by a mineralogical analysis. Polish sections have to be prepared and interpreted by using of a microscope. Figure 1 and figure 2 are showing polish sections of a platinum-nickel ore from Petchenga Nickel at Zapolyarni Mine in Russia. The head grades for rich ore are for copper between 0.05 – 0.15%, for nickel between 3 – 7% and for platinum group minerals approx. 0.15 oz/t. With an efficient flotation technology it can be upgraded to 20 oz/t."

Jan 1, 2009

By P Fullagar

Automated multi-sensor core loggers (MSCL) measure petrophysical properties of diamond drill cores, including gamma density, P-wave velocity, electrical conductivity and magnetic susceptibility. A Geotek MSCL system has been used to record petrophysical data on archival drill core from Cadia East Au-Cu porphyry deposit, New South Wales, Australia, for correlation with metallurgical parameters. P-wave modulus, calculated from density and P-wave velocity, exhibits a correlation with small-scale crushability (A*b) test results, and hence offers a means for æcontinuousÆ characterisation of ore crushability at Cadia East. Magnetic susceptibility has proved to be a good indicator of alteration styles, and is a possible indicator of crushability.

Jan 1, 2009

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships'!'. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, ' it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980

A 3-D computerised model of the southern part of Greymouth Coal Limited's Coal Mining Licence area has recently been completed. This model, and associated 3-D CAD tools, has/is being used to optimise drillhole spacing during exploratory data collection and as a visualisation and interpretation aid. This model will also provide the basis for future mine planning, with the emphasis on an optimal mine outline to maximise safety and profitable coal extraction. Previous use of computer techniques was restricted to drillhole database entry, storage and log production. Recently a 3-D geological/structural model was created for the Southern Rapahoe Sector of the Greymouth Coalfield. Geostatistical analysis of the database highlights the inadequacy of the present drillhole spacing for preliminary mine planning. The sparsity of hard data at depth results in a lower level of confidence in the accuracy of the 3-D model. Nevertheless, the model and 3-D CAD techniques has been used to target and refine ongoing resource evaluation, and provides the basis for initial reserves. In the future the geologic model will be used as the basis for preliminary and later (optimal) mine planning. It is also expected to accommodate other forms of data input in seam drilling and seismic. Development of the 3-D computer model was a first in the Greymouth Coalfield and highlights both the use of computerised techniques for resource evaluation and mining, and the effects of wide spaced drillhole data on model accuracy. The computer will continue to provide the most efficient and cost effective tool for optimal resource evaluation and mine planning as Greymouth Coal Limited moves from feasibility/mine planning to full production. The increased use of computer-based methods for mine planning should be seen as part of 'The Changing Face of West Coast Mining' in line with the theme of this Conference.

Jan 1, 1996

By Doug Bartley, Roy McKinstry, John Floyd

In March of 2001, Barrick Goldstrike became the first surface gold operation in North America to evaluate the advantages of electronic detonators. A detailed study was conducted to quantify the benefits of the use of electronic detonators to the downstream excavation, crushing and ore processing operations. The following methods were used to quantify blast performance:

Jan 1, 2003

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

In order to appreciate fully the place of palaeontology within the general framework of the geological sciences, consideration must be given to the time, about 150 years ago, just before the study of fossils was beginning to be applied to geological problems. At theend of the eighteenth century, almost all geologists recognised that fossils were the remains of animals and plants that had lived at the time when the rocks in which they occur were formed. It was also realized that many-some geologists thought all-rocks hadbeen formed under water, but as regards the order of succession in which these rocks had originated, and the relative ages of rocks found in different parts of the world or even of one country, only the haziest and most contradictory ideas existed.Around the turn from the eighteenth to the nineteenth century, a widely taught system of theories was that of the German professor, Abraham Gottlob Werner, who believed that the surface of the earth had once been covered by a universal ocean at whose bottom all rocks had been deposited. As the level of this ocean gradually subsided, older rocks-so Werner taught-are now generally found in the mountains or at great depth below the younger rocks; this was his "Primitive Division" which included granite, gneiss, schists, slates, basalt, porphyry and other igneous and metamorphic rocks, all of which he believed to be of sedimentary origin. Younger rocks, according to Werner, were formed at successively lower levels as the water receded. Next in age he placed a "Transition System" of limestones and greywackes; still younger the so-called "Floetz Division," which included sandstone, limestone, gypsum, salt, coal, but also some basalt, porphyry and other rocks; youngest were the alluvial deposits of recent clays, loams, sands and gravel. Thus, in the Wernerian system the age of a rock was determined on the basis of its petrographic properties and the height of its occurrence relative to sea-level.Here and there these ideas survived well into the nineteenth century. As late as 1825, Charles Darwin listened to lectures by Professor Jamieson, one of the last proponents of Wernerian theories in England. The fact that entirely different kinds of fossils occurredin rocks which were regarded as contemporaneous did not worry the theoreticians.It is, therefore, noteworthy and significant that the value of fossils for the interpretation of geological events was demonstrated to the geologists by an engineer and surveyor, WiIIiam Smith, who, although no professional geologist, has often been called the "Father of English Geology." His professional work, which was mainly concerned with drainage and irrigation projects, took Smith to all parts of England, where he sometimes journeyed as much as 10,000 miles in 11 year. Smith was a keen observer and, unhampered by theoretical speculations, he noted the occurrence of fossils and collected specimens wherever he went. Before long he realized that the same kind of fossils followed each other in successive layers of rocks in much the same way in different parts of England, and soon he was able, by looking at fossils collected by other people, to tell from what...

Jan 1, 1950