Search Documents

By Eberhard Rother

El presente trabajo describe el trabajo de perforación y disparo realizado en la mina de Toquepala. Debido a la configuración del depósito, el yacimiento de Toquepala debe ser trabajado por tajadas verticales. El espaciamiento entre taladros varía por diversos factores como la naturaleza de la roca, la configuración del terreno (cresta y talud de los niveles) y las condiciones de operación. En ese sentido, los taladros son cargados diariamente, exceptuando solamente los huecos húmedos con agua. Por ello, se debe analizar el carguío de taladros con explosivo, disparos primarios, perforación y los disparos secundarios.

Nov 1, 1970

A wide-ranging base of jig data was collected from various types of commercial jigs in 9 coal preparation plants in China, and a complete data analysis was made. It was found that the sharpness ofseparation was very variable, which demonstrates the complex interplay of the many factors which influence jig performance. Tests showed that there exist optimum frequency ranges in each compartment of a jig. Stepwise regression analysis indicated that the sharpness of separation is most sensitive to the intake fraction ofthe air cycle, the frequency, and the feed rate. By means of non-linear curve fitting techniques and statistical analysis, several mathematical models were developed to describe both partition curve and the jig performance, for simulation purposes.

Jan 1, 1986

Resolution Copper Mine is planned to be a 2000 m deep panel cave mine with virgin rock temperatures above 80°C in rock with a high crystalline silica content. The planned run-of-mine production rate is 120 kt/day. The project is in prefeasibility evaluation. This paper discusses features of the ventilation system design, which include multiple ventilation shafts with total flow of about 3000 m³/s and both surface and underground refrigeration systems with more than 140 MW total capacity. This will be a very challenging mine to ventilate, but this work has demonstrated that it will be technically achievable with the application of existing technology.

Jan 1, 2014

The Detachment of Coarse, Composite Particles from Bubbles

Sep 13, 2010

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

By D. M. Doyle

"The Strathcona Concentrator operations, the application of control systems in the crushing, flotation and tailing fill sections, and current and future computer control concepts are described in this paper.The computer has been used for reporting and monitoring roles and operating the on-stream analyzer since start up of the mill in 1968, while over the past twenty months, it has been used for process control. The systems which have been developed include:1. The blending of pentlandite concentrate with pyrrhotite concentrate to produce a special product of constant nickel analysis.2. The blending of cement with tailing fill to produce backfill of consistent cement content.3. The supervisory control of xanthate, frother and pH to the flotation circuits to maintain the nickel copper concentrate grade within narrow limits.IntroductionThe Strathcona Concentrator is currently treating 7,200 tons per day of an ore which contains nickel associated with the minerals pentlandite (28 -32% Ni) and pyrrhotite (0.3 -1.0% Ni). The ratio of the nickel minerals varies from 4 to 15 parts of pyrrhotite to 1 part of pentlandite over the orebody. The production of a high grade concentrate re4uires the separation of this small quantity of .oentlandite from the much greater proportion of pyrrhotite and gangue and is complicated by the presence of two pyrrhotite minerals differing in nickel content, floatability and magnetic susceptibility."

Jan 1, 1974

By D. Scott Scovira, Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance.

Jan 1, 2010

By R Hardie, J Crerar, J Merritt, B Kirsch

Longwall mining and related subsidence, and watercourse diversion for surface mining operations have the potential to impact on fluvial geomorphic processes and the health of river systems. This is evident in the Isaac River in central Queensland. The scale and likelihood of these impacts are a function of the extent of existing and proposed mining developments and of the ongoing geomorphic, hydrologic and ecological processes within the Isaac River. Understanding the objectives for the river, the past and ongoing processes at work, the cumulative impacts of longwall mining development and the options for managing those impacts is essential for the development of an effective strategy to manage the health of the river system. An assessment has been undertaken to identify and understand the cumulative impacts of mining subsidence and other mining influences on geomorphic processes and waterway health in the Isaac River over a river length of approximately 100 km near Moranbah in central Queensland. The assessment included the development of a vision and objectives for waterway health. The assessment has identified mining and landuse changes that have impacted on the hydrology, geomorphology, ecology and hence the health of the Isaac River. The assessment has then sought to identify the cumulative impact of longwall mining and related subsidence on current stream condition and the proposed vision for the system. The primary impact of longwall mining on the river was found to be associated with sediment transport. The investigation included assess- ment of total sand available for transport, the volume of sand transported annually and the fluvial process response to subsidence. Recommendations have been developed for the management of the system and for longwall mining to increase system robustness and achieve the river health objectives.

Jan 1, 2009

By Tiago Rafael Ferreira de Brito

O presente trabalho comparou o desempenho do fosfato de zinco e do microfosfato de zinco, ambos com tecnologia dry-in-place para verificação do comportamento destes revestimentos frente à conformação mecânica, por meio do ensaio de embutimento Erichsen, método Nakazima e curvas limite de conformação (CLC). Foram estudadas chapas de aço-carbono grau EM e grau EEP G4 eletrozincadas e fosfatizadas. As chapas foram fosfatizadas empregando-se dois banhos: fosfato de zinco e microfosfato de zinco, ambos com tecnologia dry-in-place. A caracterização da morfologia dos fosfatos estudados por microscopia eletrônica de varredura mostrou que as camadas de fosfato de zinco não apresentaram formação de cristais, quando aplicadas por roll coater e as análises por EDS comprovaram a presença do elemento fósforo. O ensaio de embutimento Erichsen somado aos resultados obtidos nas curvas CLC demonstraram que o microfosfato exibiu desempenho melhor em comparação ao fosfato. A diferença entre os dois tipos de fosfato foi mensurável e evidenciou que a tecnologia dry-in-place colaborou com a produção de camadas fosfatizadas adequadas para a lubrificação durante o processo de conformação mecânica.

Aug 16, 2017

By Woodcock J. T, Sparrow G. J, MacRae C. M

The external urfaces and interiors (as polished sections) of particles of coconut hell and extruded peat activated carbons taken from everal Australian carbon-in-pulp operations were examined with an optical micro cope, a scanning electron microscope, and an electron microprobe.Calcium carbonate (calcite) precipitated from the pulp was the major inorganic material on the external surfaces of the carbon particle, but several ore minerals, including quartz, hematite, pyrite, arsenopyrite, and clay minerals were also identified, along with trona, gypsum, a nickel cyanide, and a magnesium salt. Sections of carbon particles showed that calcite was virtually the only introduced inorganic material inside the carbons.It was distributed in the pores and cracks throughout the coconut shell carbon particles but tended to be concentrated in the outer layers of the extruded peat carbon particles. The mechanism of calcite formation and deposition is uncertain. Gold X-ray dot maps showed that gold was distributed through to the centre of coconut shell carbons and to a depth of at least 500 µm in extruded peat carbons. The distribution of gold within the carbon particles was similar to that of calcite.

Jan 1, 1988

By Unknown

Blast Site Security Involves: * Clearing the area * Controlling Access * Warning Signals

Jan 1, 2003

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By C Vuillier, A Roshdieh

Water is the main medium for removing impurities from iron ore during wet processing to achieve a higher quality product. However, there is a substantial increase in freshwater consumption due to an increase in demand from the following two factors: in the past 55 years the world population has doubled from 3 to 7.5 billion and crude steel production has increased five times from approximately 350 to 1662 Mt/a (IISI, 2008). Furthermore, social development in developing countries exacerbates water consumption making freshwater an increasingly valuable resource with an average distribution of 70 per cent for agriculture, 20 per cent for industry and only ten per cent for domestic consumption (Hourtolle, 2005; OECD, 2009). Rapidly changing regulations over the access and preservation of water across the world indicates the growing importance of this issue, so the mining industry must adapt to this continual change and must be committed to increasing the efficiency of water usage.Tailings dams receive most of the water used by the process plant. In arid regions where evaporation is high and availability of water low or non-existent, technical solutions other than the conventional tailings dam, such as thickened and/or filtered tailings, exist to optimise the recovery of water and reduce the need for external water consumption. However, these solutions present additional challenges, such as energy consumption and transportation from the process plant to the ultimate storage area.This paper considers a range of alternatives covering thickening and filtering, transportation and storage, water return, closure and rehabilitation. Mining projects in the future will be more affected by the rising cost in water and tighter regulations in accessing water and energy. Good tailings management can contribute significantly to reducing the dependence on these two key commodities (water and electricity), improving the resilience of iron ore projects especially in arid regions and areas with high competition for water.CITATION:Vuillier, C and A Roshdieh, A, 2017. Minimising the water loss associated with mine tailings disposal, in Proceedings Iron Ore 2017, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006

By R. D. Leitch

Spontaneous firing of coal during storage end even during shipment has long been a serious problem, especially in some regions and with some coals, and methods for preventing such firing have been investigated at intervals for more than 70 years. Spontaneous or other firing of coal waste, either outside or inside mines, has also been a problem probably for as long as mining has been practiced extensively. Much trouble has been caused by such fires, and much money has been spent in attempts to extinguish them. It is known generally that surface waste banks in bituminous-coal fields are very likely to take fire sooner or later, but it is not known so generally that anthracite refuse-bark fires also are common and that at least some of them are more serious in their effect and results than being regarded merely as a nuisance. There surface refuse fires probably would have attracted much more than local attention long ago had it not been that they usually cause no more serious trouble than air pollution. A few supposedly effective methods of preventing or extinguishing spontaneous fires have been reported rather recently. Unless one or more of these prove to be widely applicable, methods of solving these problems are no more certain today than they have been for many years.

Jan 1, 1940

By Don M. Coulter

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these holes, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By Reginald S., Dean

The commercial availability of electrolytic manganese has greatly changed the position of manganese as a nonferrous alloying metal. Manganese metal commercially available up to about ten years ago was reduced with either silicon or aluminum and contained substantial amounts of the oxides of these metals and other impurities. Manganese was accordingly not available as an alloy base and its addition to copper-base and nickel-base alloys was generally limited to a manganese content of a few per cent. Several special alloys like manganin contained up to 12 pct of manganese.

Jan 1, 1953

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By I. L. Whyte

apparent density and drag coefficient of porous ores on

Apr 1, 1995