Search Documents

By R. W. O. Kersten

"The aim was to investigate stable pillar design procedures currently in use on chrome and platinum mines, subject them to a critical appraisal, and review some of the alternatives proposed in the literature. It is concluded that these pillar design methodologies suffer from drawbacks that can be detrimental to the mining industry and that an improvement is essential.It was decided that the increased availability of analytical models and failure criteria could be exploited to update the empirical to an analytical/empirical method. The proposed methodology adopted FLAC2D simulations using the Hoek-Brown failure criterion to calculate full stress-deformation curves for typical pillars. The mine stiffness concept was introduced to determine the pillar load, integrating the influence of the pillar and strata stiffness and mining geometry.The proposed methodology was calibrated by comparing experimental and predicted deformations and failure depth of pillars in one hard-rock mine. The conclusion was that the methodology is an improvement over the one currently in use. An improved factor of safety is given by the intersection point of curves for the stiffness of the system and the pillar strength. IntroductionThe paper describes part of the findings of a PhD thesis (Kersten, 2016) on an alternative stable pillar design methodology. This publication contains sufficient information to implement the method for further interpretation and testing. A detailed comparison of measured and predicted data is dealt with in the thesis, and the results show that there is promise in the methodology.The design of stable pillars in mining is of fundamental importance, not only in the Bushveld Complex mines but throughout the mining industry. Wherever mining occurs, pillars are formed at some stage and it is essential to predict their behaviour, i.e. whether they will burst, yield, or remain stable. Although of crucial importance, pillar design still suffers from major shortcomings and weaknesses."

May 1, 2019

By Joseph A. Cybulski

In response to the mining of reserves with increasingly adverse round conditions and the roof support recommendations of current rock mechanics theories, roof support systems have continued to improve. A few of these newer bolting systems. while giving improved performance, require a new method to check bolt installation. Previous1 , a torque wrench had been the sole means to check the installed torque of a roof bolt. However, due to the characteristics of soma of the newer bolting systems which can prevent a reliable manual torque check and a recent change in the federal roof control regulations, an alternative method to a manual torque check is gaining acceptance. This alternative method improves monitoring the hydraulic pressure of the roof bolting machine torque circuit and provides a safe, reliable and quick wav to check bolt installation in those instance when an accurate manual torque check cannot be made.

Jan 1, 1990

Recent work has shown that, in at least some instances of regional metamorphism, metamorphic diffusion has been restricted to such relatively minute distances (of the order of 1.0 mm and much less), that there is no clear, direct evidence of prograde metamorphic mineral reactions, and that metamorphic equilibrium does not appear to have been attained through even very small domains.A number of stratiform orebodies and their immediate metapelitic environments exhibit very large, seemingly "disequilibrium", assemblages of regional metamorphic index materials. One such, in north-eastern Australia, includes laumontite, prehnite, chamosite, stilpnomelane and related hydrous iron silicates, primary chlorite, sericite-muscovite, epidote, actinolite, biotite, almandine, andradite, metamorphic hornblende and clinopyroxene, scapolite, staurolite and sillimanite, all within a 20 metres length of a single diamond drill core. In this and several related occurrences it appears that metamorphism has involved very small scale in situ transformation of pre-existing materials rather than large-scale diffusion and reaction, and hence that the observed metamorphic minerals have probably been derived directly from precursor materials of sedimentary/diagenetic origin.It is concluded that the fluctuating seafloor interplay between warm, acid, concentrated hydrothermal waters with cold, alkaline, dilute seawater during stratiform ore formation, together with diagenetic processes, leads to the formation of a wide range of clay, chlorite, mixed-layer clay and clay/chlorite, and zeolite precursor materials and hence, later, to the complex assemblages of metamorphic minerals closely associated with some stratiform ores. Commonly included in highly localized assemblages of this kind are various minerals which, in conventional regional metamorphic studies, are generally regarded as indicating widely different grades of metamorphism.

Jan 1, 1982

By D J. Williams

Tailings management is typically constrained by many factors that are taken as given. These include the tailings production rate that must be accommodated, the desire to deliver the tailings cheaply and easily as a slurry using centrifugal pumps, and a tailings footprint limited by the desire to minimise capital costs leading to a rapid tailings rate of rise and a low settled density. Other constraints include wall raises being delayed due to limited capital, inadequate tailings water and rainfall run-off management, and the net present value (NPV) approach to capital expenditure that puts off expenditure at the expense of performance. All of these constraints result in the tailings occupying much more volume than is necessary, being difficult to rehabilitate, and not being capable of supporting a beneficial post-mining land use or function. Ultimately, such constrained tailings storage facilities will assume very large dimensions, but each will typically be developed as a series of smaller storages that are filled rapidly and added to progressively. The optimal stage to efficiently recover process water is in the process plant, but this is limited by the desire to use centrifugal pumps rather than the more costly positive displacement pumps, which also require greater management of tailings deposition. Process water can also be recovered from the tailings storage facility (TSF) decant. Tailings water that is not recovered from the plant or the decant will be lost to entrainment within the tailings, seepage to the foundation or through the wall, or evaporation. However, tailings water is not always suitable for reuse in the plant, particularly when it becomes contaminated by the processing, and it may simply be stored on the TSF. This will exacerbate the seepage of contaminated water to the environment, and will limit the densification of the tailings that would otherwise occur due to desiccation of the tailings on exposure. If a larger tailings footprint were developed early, cycling of tailings deposition in thin lifts between a number of cells could occur, maintaining the dormant cells dry to enhance desiccation and densification, and ultimate rehabilitation. The end result would be a much reduced stored volume of tailings, the potential for upstream raising, and ease of rehabilitation to a high level. The higher initial capital cost would be overtaken by reduced ongoing capital, operating and closure costs.CITATION:Williams, D J, ?2014. An alternative whole-of-life approach to tailings management, in Proceedings Life-of-Mine 2014 , pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Frederick Bacorn

THE paper of Reno H.. Sales on Ore Deposits at Butte, Mont.,' is a careful and painstaking work, an important contribution to the literature of the subject. As is almost inevitable in a work of such magnitude, a few misstatements occur; and some of these I shall endeavor to point out. Mr. Sales has also fallen into error, as I think, in the application of his theory of ore deposition; and while the modification which I venture to suggest is a minor one geologically, it is of great economic importance. I refer to Mr. Sales's idea of an outward migration of mineralizing solutions from a supposed central copper zone. In order that I may make myself plain, I must first epitomize the theory as a whole, which I understand to be this: All of the Butte ore deposits (save those along the Continental fault, not herein considered) are derived from solutions of magmatic origin, which, at the beginning of their ascent from a great depth, were, acid in reaction, hot, and were carriers of copper, zinc, manganese and other metals. As they departed from their point of origin they lost heat, and, because of reactions with the wall rock, became more and more alkaline. The metal deposited from these solutions in their hot condition was principally copper; and, as they cooled, they deposited less and less copper and more and more manganese and zinc, until the copper practically disappeared. With this theory in general I have no fault to find, nor have I, it must be stated, the qualifications necessary to enable me to pass upon it critically; but it seems to me to be reasonable and probable, and is one which I am quite willing to accept.

Jan 8, 1914

By J. G. Pippenger

The mining industry has been Australia?s major economic driver over the past decade, contributing 8% to Australia?s Gross Domestic Product and 26% of Australian Stock Exchange Market capitalisation. Australia is the world's leading exporter in coal, iron ore, alumina, lead and zinc; and second largest in gold and uranium. While driving the economy, this resource boom has also created a demand for professional and operating talent that has far outstripped the capacity of Australia?s 21 million residents. I moved to Australia some 10 years ago and have not looked back. This unique island continent with its mix of Indigenous and diverse immigrants ? many still proud of their convict ancestry ? has offered life long memories both professionally and personally.

Jan 1, 2011

By Eugene McAuliffe

HAVING reached the status of an octogenarian plus, I suddenly decided to take a trip to Great Britain by airplane, before the possibility of hardening of the arteries made such a program too precarious. Of thirty June and July days spent in the islands, five were spent in the south of Ireland, or Eire as the politicians like to call their country. On June 15 I arrived in Glasgow where a day was spent with old friends before moving on to Edinburgh, where the Institution of Mining Engineers was billed to hold its summer session. I had received a cablegram before leaving New York inviting me to attend the sessions which I accepted with avidity, spending three most enjoyable and informative days with old friends and the officers of the Institution, Douglas Hay, president; Ian McDermid, secretary; and members of the council.

Jan 1, 1947

An Ammonia Leaching-Solvent Extraction-Electrowinning-Flotation Process for Copper Oxidised Ore Treatment

Sep 13, 2010

By Christian Wawrzyniak

An analysis method for modeling compensation grouting based on the finite element method is presented. By this method the design parameters of compensation grouting, grouting pressure and grouting volume, can be evaluated. Also the subsidence of a building due to tunnel driving as well as the lifting of the building by compensation grouting can be simulated. The stress changes in the tunnel lining and in the foundation of the building are computed as well. The application of the analysis method is demonstrated on two examples for compensation grouting in combination with construction of tunnels.

By N. D. Wineinger, J. Jodouin

"An Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) case study was completed for a mine in Ontario, Canada by SRK Consulting, Inc. The purpose of the study was to analyze the ventilation system to determine whether and which system improvements could reduce the overall electrical power demand of the mine. Financial incentives are offered by the IESO IAP grant program to help cover the capital costs of these improvements. This study included the completion of a full mine ventilation survey as well as measurement of a full suite of electrical parameters of the surface and underground ventilation fans. After these measurements, a base ventilation model was created and established as the system baseline. Changes to the ventilation system were modeled, and their effects on the power demand were projected. The results of the study showed that several improvements were possible which may significantly improve the efficiency of the ventilation system and reduce mine electricity demand.INTRODUCTIONIn 2017, a ventilation study was conducted in accordance with the Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) at a mine in Ontario, Canada. The IESO IAP is designed to assist eligible transmission-connected Canadian companies operating in Ontario to fast track capital investment in major energy conservation projects. The program will provide financial incentives to encourage investment in innovative process changes and equipment retrofits to reduce electricity consumption on the provincial system and to help companies become more competitive by positively impacting their bottom line. There are now four initiatives under the Industrial Accelerator Program:1. Retrofit2. Process & Systems, including Small Capital Projects3. High Performance New Construction4. Energy Managers – a new initiative under the Industrial Accelerator ProgramWithin the program, companies may propose energy saving changes to their current systems where applicable and appropriate. Companies may then be awarded funding to implement the proposed changes. The program allows partial financial compensation to implement certain energy saving changes that would otherwise not be considered due to high capital costs. For larger projects, such as underground mine ventilation systems, a detailed engineering study must be submitted. This study must detail each energy saving change or measure, its savings, and calculate the financial incentives using the IESO IAP Payment Structure. The payment structure for a project is an amount equal to the lowest of the following (Independent Electricity System Operator, 2015):"

Jan 1, 2019

By Jr. Wallace

This paper describes an analysis performed to determine the cool-down time of drifts in the prospective commercial nuclear waste repository in volcanic tuff at Yucca mountain, Nevada. Two emplacement methods are currently being considered at Yucca mountain. The reference configuration stores the high-level waste in short vertical boreholes, and the alternative configuration stores the waste in long horizontal bore-holes. After emplacement operations for each emplacement drift are complete, the drift will be closed off from continuous ventilation. Given time, the radioactive decay of high-level waste will increase the rock temperature around access and emplacement drifts. Air cooling may be required to re-enter these drifts. The paper discusses the analysis procedure and computer programs used to evaluate the time to cool a drift to acceptable environmental conditions 50 years after emplacement of high-level waste. Key assumptions to the analysis are presented. The results of the study show that cooling either vertical or horizontal configuration emplacement drifts is possible in a reason-able period of time.

Jan 1, 1988

By R. Frank Chiappetta, E. B. Wilson

"The maintenance records for AL-60 airlegs at Falconbridge Ltd. are used to demonstrate some of the procedures for the analysis of such data.The data are not representative of pure failure s of one type or another. In fact, the records are for the undefined pseudo-failures which are usually found in industrial operations. However, because the machines are brought to the shop only when inoperative, the individual recorded components are treated as failures. Manual calculations are conducted to show the analysis of variance (ANO VA) approach to determine whether certain data can be combined; only a limited number of the 206 machines being considered. The manual procedures continue with the weighting of the suspensions; i.e. terminations f or reasons other than the failure of the given component. After the data are sequenced in the proper order, the nature or pattern of the data is determined using the Kolmogorov-Smirnov (KS) test.It is recognized that these manual examples must be replaced by compute r methods 10 process voluminous data of this nature. Such programs are developed and available. However, a program called RELCODE is used in this case to correspond to the manual examples and to take into account the suspensions. These analytical procedures form the basis for those studies required for good maintenance management."

Jan 1, 1985

By Harry Verakis, Thomas Lobb

Over the past decade, approximately 5.1 billion pounds of explosives were used annually, on average, in the United States. Most of the explosives were used by the mining industry. The coal mining industry was and still is the dominant user of explosives. About two-thirds of the explosives consumed was used in coal mining.

Jan 1, 2003

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

By Lynch A. J

Comminution within rod mills has been investigated by use of a matrix analysis of breakage processes. A parameter, the number of breakage stages, has been introduced and comminution within all rod mills has been expressed in terms of the number of grinding stages and a function which describes the feed rate, mill diameter, and mill speed. The effect of variation in feed rate, feed sizing analysis and mill speed on the number of breakage stages is discussed, but no general relation is proposed because more study is needed.INTRODUCTIONRod mills are normally used as the first unit of multi-unit systems for the grinding of metalliferous ores and the cost of operating rod mills may be considerable. For both economic and metallurgical reasons, it is therefore necessary that the mills should be operated efficiently and that a knowledge of the mechanism of the size reduction process within rod mills should be as complete as possible. While a qualitative assessment of the process may be of some value, a quantitative assessment gained by describing the process in mathematical terms can be of much greater use because it may also be used for design and control purposes.In this paper, an empirical mathematical model is postulated to describe the size reduction process within rod mills and it is used to analyse the effects of variations in both rates and size distributions of the feed to the mills.GRINDING CHARACTERISTICS OF ROD MILLSMyers (1953) discussed the grinding characteristics of rod mills and suggested that a pronounced screening effect, resulting in the preferential grinding of the coarser particles, occurs within the mills. This is illustrated in...

Jan 1, 1964

By Changwoo Lee, Jan M. Mutmansky

"This paper results from the research at The Pennsylvania State University into establishment of standard procedures for characterization of respirable coal dust performed by the Generic Mineral Technology Center for Respirable Dust and supported by the U.S. Bureau of Mines and the Mining and Mineral Resources Research Institute at The Pennsylvania State University. The research performed within this particular project is oriented primarily toward standard methods of sampling and characterizing respirable coal mine dust underground so that the chemical, physical, and morphological characteristics are known and can be related to the incidence of coal workers' pneumoconiosis (CWP) in Pennsylvania.The research was initiated by con¬ducting a search of the literature to determine what coal and geologic variables may be related to CWP. The effects of coal rank, free silica content, the mass of respirable dust, and the level of trace elements were the major variables studied. It seems to be evident that the free silica content, the rank of coal, and the mass of respirable dust are the major concerns in defining the causes of CWP. However, based on the literature survey, the authors have concluded that verification of the causes of CWP is a multivariate problem and must be analyzed in an appropriate statistical manner.The results of a multivariate analysis of ten trace elements recorded on Pennsylvania coals are presented. Five of these trace elements were found to be of use in differentiating one coalfield from the others. Of these five elements, chromium and zirconium showed a strong positive correlation with the rank of coal while strontium showed a negative correlation.The design of the field sampling work and its application in future research is the final topic discussed. The sampling plan is oriented toward continuous miner sections with eight-stage impactors as the collection equipment. All of the field work will be conducted in the coal measures of the Allegheny Formation and above with both dust and channel samples being collected in the same mines.Coal workers' pneumoconiosis has been an important topic of concern to miners, mining engineers, and epidemiologists for decades. The general cause of the dis¬ease, the inhalation of coal mine dust, is well known, but the specific coal and geologic variables that affect the incidence and severity of the disease are still subject to debate and study. The primary objective of this study is to identify those variables of Pennsylvania coals that contribute to the CWP problem. To accomplish this task, a field sampling program is to be conducted to relate the characteristics of the coal dust, the coal seam properties, and the geologic variables to the occurrence of CWP.The first year of this study has been involved with both a literature review and experimental work oriented toward identification of causal variables related to CWP. The results of this work are presented here along with plans for implementation of the findings in future research.The previous studies of CWP causal variables have been conducted by scientists, engineers, and medical personnel. Many different types of studies have been performed with emphasis on interpreting the effects of dust mass concentration, mineralogy of the coal, the rank of the coal, and trace element concentrations upon the incidence of CWP in various coalfields. Most of the research has been conducted during the last two decades, with the British Isles, West Germany, and the United States being the primary countries involved.The review of the literature was conducted to determine which variables are likely to warrant further study in Pennsylvania. Previous research studies have related CWP to free silica and other mineral content, the rank of coal, the mass of dust in the working place, and the trace elements in the coal and lung dust. In the following sections, each of these topics will be discussed and analyzed."

Jan 1, 1988

The use of controlled recirculation can be dated back to the early 1930s. Although this method has been applied in many mines since then, a generalized comprehensive network analysis is still lacking. This paper presents a unique approach in which the ventilation network with a controlled district recirculation is divided into two subsystems: a main subsystem and a recirculation subsystem. The subsystems are analyzed individually and the results and their relationships are then integrated into discussions of the total ventilation system. The analysis of the recirculation subsystem is facilitated by introducing a non-dimensional parameter A, which represents the ratio of the air quantity for the working face to that for the subsystem. As a result, fan and regulator pressures and air power for various recirculation arrangements can be effectively expressed as a function of A and the subsystem air quantity. Numerical examples are included.

Jan 1, 1995

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990

By Baokuan Li, Fang Wang

"Comparing with the single electrode in electroslag remelting processes, two series-connected electrodes have the advantage of little inductance, lower power consumption and higher melting rate, which was widely used to produce superalloys and specialty steels. Detailed understanding of the electromagnetic field distribution is essential for both improving ingot quality and saving electric energy. In the present work, a 3D finite element model was developed for the magnetic field, electromagnetic force, current density and Joule heating field of electro slag remelting processes (electrode, slag and ingot) with two series-connected electrodes using Maxwell equation, Lorentz law and Joule law. The results show that the maximum current distribute occur at the middle of electrode, due to the interaction of selfinduced and mutual-induced of two series-connected electrode; associated magnetic flux density on the inner side of electrode increase and the outer decrease; The maximum joule heating is at the interface of slag and electrode. The parameter study shows that if the current frequency is greater than 35Hz, the current density in inner electrode tend to linear distribution; with the increasing of original current, The maximum current density near the wall in electrode will increase linearly; with the increasing of electrode innnersion depth and decrease of slag cap thickness and the maximum of the joule heat in slag will increase.IntroductionElectroslag remelting processes(ESR) are widely used to produce superalloys and specialty steels [l-3l_Two pair, four pair or six pair electrodes in electroslag remelting processes is common in casting large scale ingot, which has the advantage of little inductance, lower power consumption and higher melting rate, comparing to singe electrode. They have the same essence with two electrodes in ESR.Compared to the single electrode ofESR, the other electrode is added which can decrease the reactive resistance and power consumption in the two electrodes of ESR. It is a complicated metallurgy process with a series physical and chemistry phenomenon from the molten of steel to the solidification of ingot [4-71_ These physical and chemistry phenomenon originated the effect of alternating current of high intensity. The rule of the alternating current of high intensity which revealed the law of physical and chemistry phenomenon in ESR is the precondition of improving ingot quality and saving electric energy. Jihe Wei and Yongli Ren[S-9lstudied the distribution of electromagnetic field in single electrode ofESR with Maxwell equation and relative electromagnetic theory. It had the limitation that take the electrode and mold as infinite conductivity. A detail analysis of Electromagnetic fields in ESR had been conducted by Patel A D [JO-llJ using general stream-function formulation. It is difficult to extend to three dimensions which could not be used widely. Daniel V [lZJ and Kharicha A [BJ only analysis the current density associated magnetic flux density field and temperature field without the whole irlformation of electromagnetic field. Maopeng Geng [l4J considered the current density and temperature field of the real and fake electrodes in ESR without skin effect. As to the complication of the two electrodes of ESR, it is rarely reported the electromagnetic field and Joule heating field of the two electrodes in ESR. The rule of effect of electromagnetic and modification of numerical simulation should be studied in depth."

Jan 1, 2011

By D. C. Mahon, P. G. Sagert, M. R. Legeyt

INTRODUCTION Public opinion, over the effect of industrial development on the environment, has required government to institute guidelines for the protection of the environment both during the development of and after the decommissioning of mines. In no other area of mining has this requirement been more consistently applied in recent times than in the development of uranium mines. Uranium mines have been a focal point because of the very real uncertainties associated with the detrimental effects of radionuclides and the possible hazards of radiation. In order to determine if there is an environmental effect caused by a development or the storage of the mine waste as tailings, it is necessary to know what the quality of the environment was prior to the production of the tailings. This is the reason for baseline data programs. It is neither technically nor economically feasible to completely define the environment in any given region. Therefore, judgement decisions must be made prior to the development as to what aspects of the environment are more likely to be affected by the presence of the tailings, and to what degree. These decisions have evolved over a period of time based on information generated from existing facilities, scientific research, and the development of strong public opinions. This process is not static, but evolves with the growth of information and the technological developments which permit greater control of industrial pollution and waste management. A well-designed baseline program will reflect changes in science, technology and public attitude, even in advance of government regulations to enforce policy changes. RATIONALE FOR PREOPERATIONAL BASELINE STUDIES There are three distinct phases to be considered in the construction of an environmental assessment for a uranium mine tailings containment facility. I. Pre-operational 2. Operational 3. Post-operational (decommissioning and long term).

Jan 1, 1980