Search Documents

By Nora M. Hutt, Kevin A. Morin

The Sobek humidity cell has been in use with minor modification for more than 30 years to determine bulk primary-mineral reaction rates. As a result, it has become a key tool for predicting the bulk rate of sulphide oxidation, the Carbonate Mole Ratio (CMR) of neutralization-potential (NP) consumption to sulphide oxidation, and the rates of metal leaching. Most humidity cells are operated for less than a year, with the resulting rates extrapolated into the future for years or decades. The validity of these extrapolations was tested by examining longer trends from cells that have operated for three to seven years, as found in the International Kinetic Database (IKD). Additionally, large batches of cells for two minesites in the IKD (45 and 46 cells each) were examined to determine if regular, predictable trends were obtained across ranges of geochemistry at a minesite. The long-term cells show that the rates of sulphide oxidation and acid generation, based on sulphate production, have a 50% chance of stabilizing within one year, with the remainder fluctuating significantly throughout their test periods. Despite the fluctuations, the CMR, which is critical for defining site-specific or rock-unit-specific ABA criteria, remains relatively steady in many cases between 1.0 and 2.0 as expected from principles of aqueous geochemistry. However, if the sulphate-production rate falls below 10-30 mg/kg/wk, the CMR value can increase significantly. At and below these low rates, physical factors like flow rates of surface waters and groundwaters will determine the rate of NP consumption, rather than geochemical factors. Also, if weekly rinse pH falls to acidic values, the CMR will decrease below 1 .O, reflecting the exhaustion of fast- neutralizing minerals. The two batches of multiple cells also confirm these trends across arange of geochemistry. The long-term cells show that copper leaching often stabilizes within a narrow range as long as rinse pH remains relatively constant. Also, there is no strong dependence of leaching on the sulphate rate. However, the rate of copper production often increases sharply if rinse pH falls to acidic values. This suggests the measured copper-production rate in some cases is not a true primary rate, but a lower secondary rate after secondary- mineral precipitation within Sobek cells. As with the long-term cells, the batches of multiple cells show that copper production often increases gradually with decreasing rinse pH, with no clear dependence on sulphate production. However, high rates can also occur at near-neutral pH, so secondary-mineral precipitation of copper is not necessarily common.

Jan 1, 2000

By J. C. Irvine

Meramec Mining Company, a joint venture by Bethlehem Steel Corporation and St. Joe Minerals Corporation, is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge Mine located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during an exploration program to discover new lead orebodies. An airborne magnetometer survey which was run by the U. S. Geological Survey, the Missouri Geological Survey, and several min¬ing companies was published in 1950 and showed an anomaly in the Pea Ridge area. Test holes drilled in 1953 and 1954 revealed the presence of a large orebody of probable commercial significance; additional drilling in 1956 and 1957 provided confirmation of this. Meramec Mining Company was incorporated in 1957 and shaft sinking began in the latter part of that year. The Pea Ridge orebody lies under about 1300 feet of sediments. It is tabular, about 2600 feet long and up to 600 feet thick, and lies in an approximate east-west delineation. The orebody dips about 800S and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite, The Pre-cambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 feet 1 inch in diameter and 2500 feet deep. No. 1 shaft, equipped with an "A" type head-

Jan 1, 1972

By Albert L. St. Peter

The "Old Reliable" four million pound blast in March of 1972 marked the opening, as far as is known, of serious efforts to commercialize the In Situ concept. That was a coyote shot, and it was followed by three blasts at McAlester Fuel's "Zonia" operation which were surface hole shots. As the only individual who had a principal part in all four shots, it seems to be appropriate to present experiences in the developments and evolutions of the in Situ method of ore extraction. Some of the problems will be described, along with proposals for management of such projects in the future.

Jan 1, 1976

By P. K. Muduli

The number and the type of trucks and shovels are two important factors in determining the optimal design parameters of an open-pit mining system. Characteristics of trucks' arrival and service-time distributions determine the performance measures of a truck-shovel system when it is modeled as a closed queuing network. In all of the previous analytical queuing studies of truck-shovel systems, trucks are assumed to be identical with respect to their arrival and service-time distributions. This assumption, although desirable for reducing computational difficulties, causes either underestimation or overestimation of the performance measures depending on the number and type of equipment used in the model. The relative error in performance measures could be significant when the number of different types of trucks and shovels is large. In this paper an analytical method is proposed to model the truck-shovel system as a multiple-chain closed queuing network. This approach would provide the capability of estimating system performance measures for planning purposes when the truck fleet is not necessarily composed of identical trucks. An example of truck-shovel systems is discussed to show how the incorporation of different types of trucks does affect performance measures.

Jan 1, 1996

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, bulk-mineable, open-pitable, heap-leachable, gold-silver deposit. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold occurs principally as electrum finely disseminated through intermediate tuffs, and associated with pyrite, at Santa Rosa. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1993

By A. Hekmatnejad

"The objective of this work is to validate a methodology for spatially predicting the fracture intensity, defined as the average fracture area per unit volume. First, using the observations from drill holes, the fracture intensity is directly inferred at the support of drill-hole composites based on a Terzaghi correction. Subsequently, the composite values are interpolated to larger blocks. The methodology is tested on sets of simulated fracture networks, in which each fracture consists of a disc with a random diameter, random position and random orientation. For each of these simulated networks, one can calculate the actual fracture intensity within any region of space, based on geometric considerations. A regular sampling mesh is then defined to emulate a set of vertical drill holes and the proposed methodology is applied to predict the fracture intensity, both globally and locally. The actual and predicted fracture intensities are finally compared, showing that predictions are unbiased, insofar as, on average, the prediction error is always close to zero. Also, the error dispersion increases when the support of the prediction decreases, which is consistent with the well-known support effect. In practice, the proposed methodology allows predicting fracture intensity based exclusively on drill-hole information, without the need for simulating fracture networks in space, hence its interest. INTRODUCTION The characterization of fractures in rock masses is an important part in the evaluation of mechanical and hydraulic properties of rocks. Fractures have a large impact in disciplines such as reservoir engineering, safety of underground storage of CO2 or of nuclear waste, assessment of high-enthalpy geothermal installations, safety of mining exploitations, efficiency of in-situ leaching operations or of extraction by block-caving. As a rock mass property, fractures must be characterized in the three-dimensional space, whereas observations are limited to 1D (drill holes) and 2D (outcrops, drift walls), moreover very often to rather short stations, so that the available data are subject to geometric bias, truncation and censoring. Fracture characteristics includes the number of fracture sets and, for each set, the number, orientation, spacing, location, shape and size of the fractures must be inferred from data sampling. Some important parameters that are considered nearly in all models are fracture intensity and fracture size."

Jan 1, 2016

By X. Y. Yu, X. A. Wei, A. Zeng

"The flotation behaviors of diaspore and three kinds of silicate minerals - kaolinite, illite and pyrophyllite - using an organosilicon cationic surfactant as collector were investigated as functions of reagent concentration and pulp pH. The results show that the organosilicon cationic collector QAS122 is a suitable collector for the flotation of aluminosilicate minerals but has weak collecting ability with regard to diaspore, enabling the flotation separation of diaspore from silicate minerals using QAS122 as collector. The flotation of a bauxite ore was then studied in detail. Finally, a reverse flotation separation process was used to process a low-grade bauxite ore. It was concluded that use of the organosilicon cationic collector is effective. A concentrate with aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, of 9.67 was obtained from natural bauxite ore with A/S of 6.07 at pH of around 11. The Al2O3 recovery rate was 81.72 percent. IntroductionChina has abundant bauxite ore resources, but more than 98 percent of the bauxite ores are the diasporic type, with the characteristics of complex mineral composition, low aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, and difficulty of processing. The gangue minerals in bauxite ores are mainly kaolinite, pyrophyllite and illite, containing titanium and iron impurities (Zong et al., 2008). It is known that high-grade bauxite ore, with A/S greater than 8, can be processed directly by the Bayer process (Papanastassiou et al., 2002; Ma et al., 1996). However, Chinese diasporic ores have been processed mainly by the sintering process, which is environmentally damaging and energy intensive. Increasing the A/S of the diasporic ores using a flotation method is needed (Xia et al., 2010).Froth flotation is one of the most widely used processes to concentrate valuable minerals in beneficiation ores. It is particularly useful for separating finely ground ores from their associated gangue minerals. For diasporic bauxite ores, flotation is applied to obtain high-quality material for the Bayer process by increasing the A/S. Direct flotation has been shown to be an efficient method for the desilicating of diasporic bauxite ore (Wang et al., 2004; Xu et al., 2004), but reverse flotation has more advantages for this purpose, including less collector consumption, less foaming product and less effect on metallurgy (Liu et al., 2007; Hu et al., 2003; Hu, 2003; Luo et al., 2001)."

Jan 1, 2015

By A. Jahedsaravani, M. Massinaei, M. H. Marhaban, N. Mehrshad, M. I. Saripan

"It is well known that froth visual features reflect the operating conditions of the flotation process, so that being able to accurately obtain the froth properties is the most significant criteria to optimize and control this process. Froth segmentation is a useful procedure that can determine the bubble size distribution. Several algorithms have been proposed in this field, but marker-based watershed transform shows the best performance. In spite of this fact, the algorithm suffers from oversegmentation in cases when the flotation froth includes large bubbles along with small ones. In the paper, the marker-based watershed method is modified to prevent oversegmentation of large bubbles. The developed algorithm is validated using some froth images captured at different operating conditions, so the results indicate that the method can segment the mixture of big and small bubbles effectively.IntroductionFroth flotation is a widely used process for separating valuable from gangue minerals. Effective control of flotation circuits has a dramatic effect on overall performance of a mineral processing plant. In most flotation plants, process operators monitor the froth surface visually and make adjustments to process parameters based on their interpretation of the surface appearance and their idea of the appearance of an ideal froth. However, due to natural complexity of the flotation process, achieving optimal control is often not possible for human operators.In recent years, attempts have been made to control the flotation circuits using machine vision systems (Moolman et al., 1995; 1996a,b; Bartolacci et al., 2006; Kaartinen et al., 2006; Vanegas and Holtham, 2008; Aldrich et al., 2010). The froth bubble size distribution is the most significant control variable that reflects the operating conditions in a flotation machine. To date, a number of approaches have been proposed for bubble size measurement from froth images, including segmentation (Sadr-kazemi and Cilliers, 1997; Wang et al., 2003; Mehrshad and Massinaei, 2011), texture spectrum (Nguyen and Thornton, 1995), wavelet (Liu et al., 2005), an improved texture spectrum approach, a method based on binary images (Lin et al., 2008) and, finally, using interfacial morphological information (Yang et al., 2009)."

Jan 1, 2015

My "outside exploration" began in November 1908, only 16 months after I had come to Bisbee as a raw engineer. The well publicized reputations of eminent engineers up to that time, including John Hayes Hammond, Herbert Hoover, James Douglas, D.C. Jack- ling, J. Park Channing, and a few others had been due to new mines they had found or brought to successful operation. And here was I, a mere youngster, given a chance to join the group. I knew there would be disappointments but I had no idea how many of them. In spite of the many prospects that turned out to be worthless I never looked at a new one without the feeling that this one might turn out to be the big success. This confidence, blind as it was, gave every arduous examination a zest and it made me climb every mountain on which the owner said there was something worth seeing, or on which T could see a distant staining that might mean ore. If I looked at every showing the owner suggested he at least would think I was honest and would bring other properties to our attention. This reputation of never refusing to go to see an outcrop, no matter how hot the desert sun or how rough the terrain, was probably one of my best assets. High as my hopes were at the start, they proved not to be exaggerated and if I were given a chance to do it again I would not hesitate, in spite of the jaundice, rheumatic fever, and other maladies that beset some of the expeditions. On the whole the results have equaled all my hopes. Toward the end of my years of active exploration I totaled up the score. Out of the prospects submitted to us about two out of three were eliminated after questioning the owner or prospector, without an examination. This left about a 1000 mines or prospects that seemed worth at least a preliminary look. One out of seven of these was worth a little development and a seventh of this seventh turned out to be a modest success or better. And nine or ten in all, or one out of 1000

Jan 1, 1976

By R. D. Rein

The Henderson mine is a large continuous panel caving operation in central Colorado. The orebody is roughly 760 m by 910 m and will be extracted from two production levels. Each level is divided into three north - south panels 244 m to 317 m wide. The general arrangement of a production level and its associated undercut drifts is shown in Figure 1. The production drifts (3.6 m by 3.7 m) are spaced 24 m apart center to center and have undercut drifts (3.4 m by 3.8 m) 17 m directly above them. The production drifts are interconnected with drawpoint crosscuts (4 m by 4.3 m) driven on 12 m centers. Drawpoint crosscuts receive substantial brow steel and concrete support prior to undercutting. The brow steel is a 15 cm by 46 cm wide flange beam with a 2.5 cm wear plate to box in the 'cave' side of the beam. The concrete is a minimum of 0.3 m thick and the batch design results in 27 500 kPa strength. The finished drawpoint opening is 3.7 m by 3.2 m with a choke area of 3.7 m by 2.4 m. (Figure la) Undercutting and bell formation is accomplished by blasting rings of 7.6 cm holes drilled from the undercut drifts. The rings have a burden of 2.0 m and six rings develop one complete bell.

Jan 1, 1985

By L. Blain

In practice, geochemical analyses can be grouped in two broad categories according to their aim. Those that seek to determine the exact chemical composition of geological materials fall under the heading of assays, whereas applied geochemistry concerns itself with the detection of anomaly contrasts. Recent trends have blurred the distinction between both approaches for many users, as methods that were traditionally used for assays are being adopted in applied geochemistry and assays make increasing use of instrumental techniques. Nevertheless. it is important to keep a clear distinction between the two types of analyses because it has immediate practical consequences, cost is the most obvious, as well as fundamental implications. In the broadest terms, the goal of geochemistry is to strike an optimal balance between throughput and accuracy, at the lowest reasonable cost, while assays strive for accuracy. Traditionally, complete silicate analysis has been the concern of assayers whereas exploration geochemists have been more interested in base metal analyses where acid extractions of the elements, without dissolution of the silicate matrix, has been the norm. This kind of distinction is less realistic now, especially with the growth in lithogeochemical studies, and some overlap in methodology is unavoidable. However, where such overlaps occur the distinction remains in the emphasis of the work. A commonly used example is that although HF acid preparations are used by both, the emphasis in applied geochemistry is on sample throughput and batch analysis, whereas assayers are more concerned with the range of elements to be determined (Thompson and Walsh, 1983).

Jan 1, 1993

By R. R. Godard

The practice of dust abatement or control is not new to any operation of United States Steel Corporation. This report will review those activities, past and present, within the five operating districts of United States Steel-Coal Operations with specific reference to mechanical and continuous mining, and including both the health and safety aspects of the problem. Obviously, the first principle of dust control is to inhibit its formation If this is not practical, steps may be taken to prevent its becoming airborne. Airborne dust control can be realized by either collecting it at the point of generation, diluting it with large volumes of air to reduce concentration, settling it by various means, or with reference to ignition hazard only, render it incombustible by neutralization with an inert material. These basic principles have been verified by the work of many, including the Bureau of Mines, U. S. Department of Interior, Bituminous Coal Research, Inc., and the Mining Research Establishment of the National Coal Board of Great Britain. Their application to every day mining problems is best illustrated by the following examples.

Jan 1, 1967

By T. Reed Scollon

Before we can attempt to answer the question of what can be expected from coal research, let us examine why research is done in other fields and what others expect for the money they spend on research and development. Up to 1900 almost all organized research was carried out at universities. Most of the support came from the university, and by present standards the amount of research was extremely small. The motivation for university research was basically discovery of new phenomena, with the objective of advancing knowledge. Side by, side with this organized effort was that of individual inventors who were primarily responsible for applying this new-found knowledge to useful purposes. During this period inventors were rarely supported by anyone, and experimentation was carried out either in their spare time or at the expense of earning a living. Men like Edison, I believe, were the first to demonstrate on a large scale that one could systematically apply newly discovered scientific principles to inventions that would serve useful purposes and would return a profit to those engaged in the effort. The tremendous expansion in research therefore began with the realization and demonstration that the scientific discovered could be applied in such a way as to return a' handsome profit to those who invested in it. The motivation of many of the research personnel however, remained the satisfaction associated with new discoveries, The money to support their efforts came from those interested in a return on their investments. Since the First World War and a rapidly accelerating rate since the Second World War another important motive for supporting research has appeared--the needs associated with national defense; this type of research has been supported almost exclusively by the Government.

Jan 1, 1959

By M. Laliberte

"Gold-mine effluents are often characterized by high concentrations of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While not acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be nonlethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25°C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.IntroductionThis paper will demonstrate that gold-mine effluents, which are toxic to fishes and invertebrates, can be made nontoxic by using a combination of chemical precipitation and biological oxidation.The typical composition of gold-mine effluents will first be described. The applicable legislation will then be introduced, with its requirement that the treated effluent be nontoxic. The toxicity of a typical untreated effluent will then be confirmed, and the sources of the toxicity identified. After that, a number of toxicity reduction treatment methods will be presented, and the selected method will be described.The lab tests that confirmed the efficiency of the treatment method will be presented, with three phases of testing as the understanding of the process gradually improved. Toxicity test results showing that the water is nontoxic after treatment through the temperature range will be presented."

Jan 1, 2015

By Jan Visman, James W. Parkinson

GENERAL INTRODUCTION Sample collection, preparation and analysis are all steps in a single process designed to provide information about a much larger amount of material than the sample itself. For example, information about the ash content of a unit train load of coal may be derived from a single, relatively small sample of perhaps a few hundred pounds (liters) extracted from the entire shipment. These three steps can be thought of as links in a chain, allowing the simple analogy that the strength of the chain, or, in other words, the value of the information is only as strong as the weakest link. Sample collection, discussed in Part 1 of this chapter, is critical because analytical procedures can do no more than reveal the characteristics of the sample presented to the laboratory. If that sample does not properly represent the population to be characterized, neither will the analysis of that sample. Sample preparation is also a critical part of the chain. Any change in the nature of a sample between the time it is collected and the time it is analyzed will appear to reflect the nature of the population. For example, sample preparation procedures that allow air to partially dry the coal sample before reaching the laboratory will cause the sample analysis to indicate a lower moisture content than the sample originally had. Other changes can be more subtle. Second only to moisture loss, oxidation reactions generally cause the greatest problems. Oxidation of a coal sample can alter surface properties, changing flotation response. In extreme cases, combustion parameters, such as caking or agglomerating properties or mineral composition, such as pyrite content, can change. Water samples can also be altered by oxidation. For example, ferrous iron can oxidize to ferric iron, possibly changing water quality parameters such as pH. Sample analysis, the subject of Part 2 of this chapter, is the final link in the chain. Obviously, no laboratory procedure can correct for problems created by improper sample collection and preparation. At the same time, poor analytical techniques will create incorrect information about the total amount of coal from which the sample was extracted (the population) in the same manner as improper sample collection and preparation. The key to gaining correct information about the population is to view these three steps as parts of a single process. Following proper techniques through only one or two steps of the process will not produce accurate information.

Jan 1, 1991

By C Rutter, N Shea, K Kolobe

The Henderson mine, a panel cave mine in Colorado, has undergone multiple ventilation system changes to meet dynamic airflow needs. This paper explains the ventilation designs for different production panels, the challenges faced, and the modifications made to optimize the ventilation systems. The study highlights the importance of a robust ventilation system for safe and productive mining.

Mar 2, 2022

By T. J. Durbin

At some surface and underground mines, control of ground-water inflow involves significant costs. These costs include the capital costs for installing a dewatering system, power and other costs to operate and maintain the system, and costs to treat and dispose of the water that is collected. To minimize these costs, design of a dewatering system utilizing wells has been formulated in terms of a nonlinear operations research problem using quadratic programming. Using this formulation, the locations, depths, pumping rates, and pumping schedules of wells are selected so as to minimize the total costs of the dewatering system.

Jan 1, 1993

By G. B. Walker

The success of Heavy Media Separation, the static sink-float process, is evidenced by the operation of an estimated 300 installations treating many millions of tons per year of a wide variety of mineral products ranging in value from gravel to diamonds. The static heavy media process is usually limited to the treatment of plus 1/4 inch material. Mr. Victor Rakowsky, who was largely instrumental in the development and application of heavy media separation, recognized the need for a new apparatus and process which would extend the application of heavy media into the finer size range without placing a restrictive limit on the top size of the feed. He recognized the requirement for the application of centrifugal force to augment the force of gravity in separating fines by sink-float techniques.

Jan 1, 1966

By David Chastka, Isidro Rivera, Shawna Von Stockhausen, Idit Zarchi

The City of Santa Cruz Water Department is replacing the existing Newell Creek Dam inlet/outlet works at Loch Lomond Reservoir in the San Lorenzo Valley. The project will improve the City’s overall operational efficiency, improve system performance, and improve the safety and reliability of storage for the City’s drinking water supply. The project comprises new inlet works* (three new inlets that control and convey flows into and out of the reservoir, and an intake control building), an inlet/outlet tunnel with a 48-inch conduit to convey flows into and out of the reservoir, and a new outlet structure at the toe of the dam. The outlet structure includes a release point for energy dissipation of emergency drawdown flows, a connection to Newell Creek Pipeline, and beneficial releases into Newell Creek. The project also includes a new dam seepage collection and monitoring system and appurtenant structures such as a culvert bridge over the spillway plunge pool to improve access to the new outlet. Notable complex project components include in-water work to connect the new intake shaft pipes to the three new inlets. The project includes one major milestone with a work window regulated by environmental permits that could only be amended/ extended with approvals from those agencies. If not met, the milestone work would have caused significant delays (potentially up to one year) to the project.

Jun 13, 2021

By Brett P. Spigarelli

"To meet the growing need for CO2 capture and storage technology, Michigan Technological University is studying CO2 capture using alkali-based solvents. The objective of the present study was to find a way to increase the absorption rate of CO2 into an alkali solution without reducing the absorption capacity of the solution. One approach to increasing absorption rate is to use a surfactant to chemically alter the gas bubble size. The surfactant chosen for the study was a neutral-charge polypropylene glycol methyl ether (PPGME) with a molecular weight of 200. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations. Results showed that as the concentration of PPGME increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 x 10-3 mol/min CO2 at 0g/L PPGME to 3.92 x 10-3 mol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in the absorption capacity of the solution. IntroductionChemical absorption using an amine solvent is currently the most mature carbon capture and storage technology available. Amines are advantageous in that they have a fast CO2 absorption rate, which leads to a high CO2 removal efficiency. However, amine absorption has some considerable drawbacks, such as high energy requirements, high equipment corrosion rates, amine degradation in the presence of oxygen, high waste generation and a large increase in plant footprint if new equipment is constructed (Herzog and Golomb, 2004; D’Alessandro et al., 2010). Due to these drawbacks, Michigan Technological University (MTU) is studying CO2 absorption using alkali-based solvents, which address the above disadvantages of amine solvents."

Jan 1, 2015