Search Documents

By W. H. Forbes

The prevention of accidents from falls of roof and coal requires a considerable amount of personal judgment , for conditions are different even in adjoining working places in the same mine , and conditions may change from hour to hour even in the same working place as the coal is shot down and loaded . Experience has shown that many men can not or do not exercise enough care to protect themselves from injuries ; moreover , where the foremen have been made directly responsible for the safety of the men under them , accidents from falls of roof and coal have , in many instances , been reduced as much as 50 per cent . There is now no question that careful , constant , and intensive supervision is essential in preventing acci- { dents and more especially accidents of this class . Falls of roof and of coal account for approximately 50 per cent of all coal mine accidents and annually result in the death of approximately 1,000 men and cause lost - time injury to approximately 50,000 men . These and other accidents are recurring with little or no diminution , usually not because of the lack of knowledge of safe and dangerous practices , or of the technique of safety , but largely because of the lukewarm interest of major executives in safety or the failure of mine officials to formulate and to enforce common - sense rules and regulations . When failure is the outcome of a sincere attempt of the managing officials to teach safety to the miner , the fault may usually be attributed to misguided effort . Various solutions for the problem of eliminating accidents from falls of roof or coal have been suggested , some of which are : Standard system of timbering for the specified mining districts ; departure from the room-and - pillar system to a more concentrated system of mining ; more intensive supervision - that is , 1 section foreman for every 25 loaders instead of 1 section foreman for 75 , 80 , or even more loaders the practice in most mining districts . - However , investigations conducted by the writer at numerous mines operated by a number of mining companies in several districts show that employees and officials alike are inclined to work under loose and unsupported roof , relying solely on the " drummy " sound and on their judgment and experience as to whether the roof will stay in place for one hour or for several hours . With but few exceptions , men who had been injured by falls of roof or ccal or were found working under loose and unsupported roof , admitted that they knew of the possibly unsafe condition , but it was their opinion that the roof or coal was not loose enough to fall for some time .

May 1, 1931

The Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining (hereafter referred to as the Panel or the TSP) was established by Section 11 of the Mine Improvement and New Emergency Response Act of 2006 (MINER Act). The Panel was charged with providing “independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant properties of belt materials in underground coal mining.” The TSP was impaneled by the Honorable Elaine L. Chao and commenced its work on January 9, 2007. At this first meeting, Mr. Richard E. Stickler, Assistant Secretary of Labor for Mine Safety and Health, asked the Panel to report on many issues including how recent technological advances could be applied to atmospheric monitoring systems, point-type heat sensors, current state of fire-resistant vs. fireproof belt materials, and belt fire suppression systems to improve miner safety. In addition, Mr. Stickler asked the Panel to review belt air velocity limitations. The Panel members attended 12 days of public meetings over a nine-month period. Three of the public meetings were scheduled for the Panel to hear from technical experts and those persons or organizations interested in providing input. The meetings were held in Coraopolis, Pennsylvania with emphasis on belt fires, belt maintenance, belt flammability and toxicity, ventilation, and escape issues; in Salt Lake City with emphasis on ground control and convergence issues; and in Birmingham with emphasis on fire detection, sensors and atmospheric monitoring systems. National Institute for Occupational Safety and Health (NIOSH) researchers, Mine Safety and Health Administration (MSHA) personnel, representatives of the major belt conveyor manufacturers and a representative of the National Mining Association provided discussions at the Coraopolis meeting. In Salt Lake City, Utah, MSHA district managers and ventilation specialists, a member of the Aracoma Mine No. 1 investigation team, a representative of the Bureau of Land Management, and industry and consulting representatives of the Utah Mining Association and the Colorado Mining Association made presentations. In Birmingham, Alabama, atmospheric monitoring system representatives, NIOSH researchers, representatives of coal mining companies, and UMWA workers from two Alabama mining companies made presentations. In addition, a staff member of The Center for Regulatory Effectiveness also presented comments to the Panel. In conjunction with the meetings in Salt Lake City and Birmingham, three-member subcommittees of the Technical Study Panel made field visits to the Skyline Mine, the Aberdeen Mine, and the Jim Walter Resources Mine No. 4. The mine visits were scheduled to see first-hand the mining conditions under which belt air was being utilized as an additional source of intake air for working sections.

Homans [1950] offered a working definition of group that is useful for this research: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at secondhand, through other people, but face-to-face." This chapter begins with a discussion of the group concept in reference to the hypothesized escape groups mentioned earlier. It then moves to an examination of analysis techniques used by the authors. Finally, the subjects themselves are profiled according to their demographic characteristics. The Nature of Groups Warriner [1956] took a realist approach to understanding groups: "(1) the group is just as real as the person, but (2) both are abstract, analytical units, not concrete entities, and (3) the group is understandable and explicable solely in terms of distinctly social processes and factors, not by reference to individual psychology." Warriner's realist position merely holds that "group" occupies a different domain in which it is no more or less concrete than "person." At this group level the unit of analysis will be those relations that indicate social rather than individual behavior. It is possible to investigate these group properties empirically-if a researcher avoids confusing conceptual entities with concrete ones. Most people seem to accept that group attributes must somehow be inferred, but think personal attributes will be directly manifested, requiring little or no interpretation [Snizek 1979]. In other words, nobody would equate physical components of an underground working section with the actual work group, yet social scientists (as well as laypeople) very often confuse real individuals with notions of the person. In actuality, neither groups nor persons are directly disclosed to the senses; both are inferred by experience and observation. One can "see" a group just as clearly as one can "see" a person, given the proper perspective from which to do so. It is necessary, in developing this perspective, to begin with a sound definition of the thing being examined. Besides communication, or more generally, social interaction, Homans [1950] included three other components of group makeup. "Sentiment" is characterized as the feelings people tend to form about one another when they interact often. These feelings include not only friendliness and dislike, but attitudes such as approval or disapproval. A "norm" is an idea, held in common by group members, that specifies how people ought to behave in given circumstances. In lay terms, norms are simply those informal rules individuals abide by in order to get along together in social situations. Finally, "activity" refers to those things persons do with others. In work groups, as an example, many of the activities are cooperative and goal-directed.

Jan 1, 2000

By C. A. Herbert

"The Workman's Compensation Law of Indiana, enacted in 1915, amended in 1917, 1919, 1923, and 1927, and in 1929 named the Indiana Workmen's Compensation Act of 1929, provides for a weekly compensation for disability due to accidents of 55 per cent of the average weekly wage of the employee, to start on the eighth day of disability. Compensation is computed from a maximum and minimum weekly wage of $30 and $16, respectively. Thus, the maximum weekly compensation is $16.50 and the minimum $8.80; the total compensation paid is not to exceed $5,000.In addition to the compensation the employer is required to pay all medical, surgical, hospital, and nurse fees for a period of 30 days and may be required to pay such fees for an additional 30 days at the direction of the Industrial Board of Indiana. In the case of fatalities the employer must contribute $100 toward funeral expenses.The law also stipulates that ""the employer shall keep a record of all injuries, fatal or otherwise, received by his employees in the course of their employment,"" also that the employer shall report within one week of their occurrence all accidents that cause either the death of the employee or the loss of more than one day's work. However, no standard form is furnished or required by the industrial board on which the employer shall keep a record of accidents, neither is he required to report the time of return to work of the injured employee unless the period of disability exceeds seven days and the accident thus becomes compensable. Hence, no record is kept of noncompensable accidents other than the first report sent to the industrial board by the employer.If the employer were required to keep a complete and concise record of all accidents, in duplicate, on a special form either furnished or required by the board, giving all of the essential data in regard to the accidents, and if he were required to submit a copy of this record to the board at the end of the fiscal year, the data thus assembled would not only be of material assistance to the board, particularly in making up its annual report, but would also furnish information of much value in the study of accident causes and what may be done to remove them.Those industries that have made marked progress in reducing accidents keep such records, as it is only through a full knowledge of how accidents occur that intelligent steps can be taken to prevent their recurrence. Unfortunately, the mining industry as a whole in Indiana has not kept pace with many other industries in reducing accidents, and it is urged as an aid to improvement that a thorough and complete record of mining accidents be kept."

Dec 1, 1932

This chapter analyses the parameters influencing initial design of communication systems, for new mines and upgrading existing systems. Paragraph 5.2 outlines those variables that must be taken into account during the design stages of a new wired phone system. Recommended features, general requirements, and how they can be implemented are treated in this section. Paragraph 5.3 describes ways of improving or extending the range of trolley carrier phone systems and pager phone systems already installed in the mine. 5.2 New Phone System Design The task of designing an adequate communication, control, and monitoring system for an underground mine must be addressed on a system basis. In addition to insuring that effective voice communication is established, any new system should take into account present and future requirements of remote control and monitoring functions. Chapter 4 illustrated the drastic savings in response time that can be realized when remote control and monitoring are integrated into the overall communication system. The importance of including control and monitoring in the overall design plan for any system cannot be overemphasized. Because each mine is unique, and thus usually has its own special operating characteristics and communication requirements, there is no such thing as "the one best system" to meet the requirements of all mines. The optimum communication, control, and monitoring system for a mine must be one that has been tailored to meet the special requirements of that particular mine. Factors that must be considered during system design include- a. Type of mine and mining methods (low- or high-seam coal, deep hardrock mine, stope caving, longwall, room and pillar, etc.). b. Maximum number of working sections. c. Expected mine growth rate and eventual maximum size. d. Haulage methods (tracked trolley, diesel, belt, etc.). e. Underground power distribution system (dc, ac, or both). f. Features desired (two-way radio paging, private line capability for emergency use, etc.). g. Redundant or backup systems for use during outages of the normal system. Although no two mines are alike, the following items have been established as the main characteristics desired for any underground communication system: 1. Multiple Communication Paths to Outside--the objective here is to give all telephones a second method of communicating with the surface. 2. Audible Emergency Signaling--the communication system provides the main means of alerting miners during emergencies. The system should include means to broadcast distinct audible signals for emergency signaling. Initiation of these signals should probably be controlled from. a central outside point, such as a surface control room. 3. Emergency Override--provisions should be included to permit any conversation to be overridden with emergency communication. 4. Selective Area Page--as mines grow larger it is apparent that the entire telephone system paging mode need not be activated each time a call is initiated. When the general area of a

Jan 1, 1984

By William H. Pomroy, Shail J. Butani

"This Bureau of Mines publication presents a statistical analysis of official U.S. Mine Safety and Health Administration (MSHA) metal and nonmetal mine fire reports from 1950 through 1984, plus accounts of selected nonreportable fires (less than 30 min and no injury) and opinion data on fire hazards from mine safety directors. Fires were analyzed by time trends, ore type, ignition source, burning substance, location in mine, equipment involved, means of detection, duration, number of injuries and fatalities, mining method, and successful extinguishing agent. The leading ignition sources were electricity in underground fires and engine heat in reported surface fires. The most frequent burning substance was combustible liquids for all nonreportable fires, reported surface fires, and reported underground fires from 1978 to 1984. For underground fires reported prior to 1978, timber was the leading burning substance. Mobile equipment was the type most frequently involved in both underground and surface fires. Underground fires occurred most often in haulageway or drift areas, and reported surface fires occurred most often in plant and mill buildings, while most nonreportable surface fires occurred in other areas. The most common methods of extinguishment were water hose lines for reported fires and dry chemical handportable extinguishers for nonreportable fires. INTRODUCTIONIn support of the Bureau of Mines research on mine fire protection, two separate baseline studies on mine fire incidents have been prepared. The first study addressed coal mine fires. The results of that study are summarized in the Bureau's Information Circular 8830, ""A Statistical Analysis of Coal Mine Fire Incidents in the United States From 1950 to 1977."" This second report, addressing metal and nonmetal mine fires, is the companion to IC 8830. Together, these two reports provide a comprehensive, factual summary of the mining industry's fire experience.This report, like IC 8830, covers (1) MSHA fire incident reports, (2) records of nonreportable fires (less than 30 min and no injury), and (3) mine safety directors' opinions on fire hazards. The MSHA fire reports provide the most reliable, objective, and accurate historcial record of the major noncoal mine fires that occurred during the study period (1950 through 1984). However, MSHA fire reports alone understate the true magnitude of the fire problem because metal and nonmetal mines have been legally required to report fires to MSHA only since 1968. Although some fires were reported prior to 1968, doubtless a great many were not. Also, the reporting regulations that took effect in 1968 specify that only fires lasting 30 min or longer or involving an injury need to be reported. MSHA fire reports are thus limited in scope by MSHA's legal authority. In order to provide a more comprehensive data base, it was also necessary to gather and analyze mine company records of nonreportable fires."

Jan 1, 1986

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By Noel N. Moebs

The Bureau of Mines conducted five reconnaissance magnetometer traverses across a small abandoned chromite mine in the State Line district of Pennsylvania and Maryland to determine the geophysical response of the area. The results indicate that more extensive geophysical surveys of the region might establish some worthwhile guidelines for chromite exploration. While chromite only rarely can be detected directly by magnetic methods, there is a possibility that geophysical signatures in the adjacent host rock could provide some guidelines for further exploration. Prior to 1875, all the chromite produced in the United States came from the State Line district, and the potential for discovering additional podiform deposits could be significant. Virtually no state-of-the-art geuphysical or geochemical studies have been conducted in this district since World War II and sizable areas remain undeveloped and suitable for exploration. While the results reported in this paper are not supported by drilling, it may encourage others to investigate the area more fully for improved methods of detecting subsurface podiform chromite deposits. New theories on the emplacement of ophiolites also could contribute to an assessment of the chromite potential of the serpentinite belt.

Jan 1, 1991

By Oliver A. Dibble

This paper it one of a series being prepared for and published by the United States Bureau of Mines, describing mining methods and costs at clay pits throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The open-pit recovery of clay for cement plants is a comparatively simple operation in comparison with underground mining of clays; nevertheless, it represents an appreciable factor in the cost of cement manufacture. The following report deals specifically with the methods employed by the Aetna Portland Cement Co., which operates cement mills at Fenton and Bay City, Mich., in recovering clay from their pit at Corunna, Mich., on the Grand Trunk Western Railway.

Jan 1, 1932

By H. H. Hill

"The wide publicity that is given to the discover; of new oil fields has led many people to believe that our supply of crude petroleum is practically in- exhaustible and that in order to keep pace with the demand for petroleum products, it is only necessary to drill a few more wells in some of the south-western states. It is not generally realized that, although many famous fields have been developed in Oklahoma, Kansas, Texas and Louisiana during the past few years, the production of crude oil in 1919 was not sufficient to meet the demand and it was necessary to import approximately 53,000,000 barrels from Mexico.Continued efforts are being made to recover a larger percentage of the oil underground by improvements in methods of drilling and in handling producing properties. Improvements are also being made in methods for handling the oil after it has reached the surface which will result in reducing losses through leakage and through evaporation. These methods for cutting down waste in production and storage, if universally adopted, will no doubt result in appreciable increases in our supply of crude oil."

Nov 1, 1920

Track and control the tram maneuvers of continuous mining machines by developing and evaluating a laser sensor system. Background Progressive technology has the potential to greatly improve mine-worker safety, helping to create a safer, better working environment for mine workers by keeping them away from the dangerous face area. To benefit from such technology, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A cornerstone for computer-assisted operation is an effective guidance system. Since there are no guidance systems on any commercial continuous miners (CM's), the Bureau it-self developed and tested a laser-based sensor system, based on a commercial sensor called Lasernet. The laser-based guidance system employs four laser scanning sensors at fixed locations in a mine entryway to report the angular coordinates of two cylindrical retro-reflective targets mounted on a CM. Using triangulation, a real-time microcomputer system processes the sensor data and updates the xy position and heading (h) of the CM five times per second. Using a simple control algorithm and communications interface to the CM control computer, the system also controls rotational and translational tram maneuvers.

Jan 1, 1992

By Clyde E. Eilliams

In recent ye.ars much intere,t has been centered on the possibility of pro­ducing alumina from clq, a.nd proposed methods tor the recove:r,v of alumina are appearing constantly in parent lit,erature, As a good· grade of clay contains from 30 t<> 40 per cent of al"WDina, the prospect of tecovering it is alluring, al though obviously ditfieul t. A patent typical of m projected thermal processes is that 0£ Paul Migu.et, (U, S, Patent No, l,376,563) entitled nprocess for the preparation of pure alkaline alu:ninates.'' Re proposes to prepare alkaline a.luminate by fusing clay, lime, and acrap iron with a reducing aget in the electric furnAce, thereby reducing the silica a.r.d formin1s calcium alumina.te and ferrostlicon, The calcium aluminate, being lighter, would. float on top substantially free from foreign oxides, It could. then be tapped ott, cooledf ana later crushed and leached with aodium carbonate solution to torm, by double decomposition, sodium aluminate, and calcium carbonte. The fonMr is soluble and yields readily aluminum hydroxicie. 'l'he ferrosilicon wo'Uld be r,covered as such and sold at a profit.

Aug 1, 1922

By John B. Shutack

In an effort to improve the performance of the explosive-anchored rock bolt, the Bureau of Mines studied the effect of the detonation velocity of the explosive and type of charge (linear or nonlinear) on the fracturing tendency of the anchor tube. Also, different types of tubing were compared to determine the one most suitable for use as an anchor tube. The Bruceton up-and-down method was applied in tests in which steel shooting blocks having boreholes ranging from 1-3/8 to 2-1/8 inches in diameter were used. Of the four types of tubing evaluated, a welded A-178 tubing that was drawn over a mandrel and renormalized gave the most promising results. The A-179 seamless tubing that is normally used with the explosive bolt was the most inferior. Both types, however, gave significantly better anchorage than the conventional shell when tested in both laboratory and underground experiments. Within the range of velocities studied (5,000 to 7,000 m/sec), the type of explosive showed no significant effect on anchor-tube performance. In general; linear explosive charges provided better anchorage than nonlinear charges.

Jan 1, 1968

By Carl E. Norman

An investigation of geologic structure on macroscopic, mesoscopic, and microscopic scales was conducted on near-surface igneous and metamorphic rocks in which the existing stress field was determined by in situ methods. A consistent NE-SW orientation of the maximum compressive stress in the horizontal plane at four of five test localities appears due to the intrusion of NW-trending diabase dikes. Structural features at the mesoscopic scale show no consistent directional relationship to determined stress directions. Petrofabric diagrams of open microfractures show preferred orientations, but these are not consistently related to the orientations of larger structural features, such as joints, foliation, or mineralized shear zones. However, at five of six test sites the preferred direction of microfractures occurs nearly perpendicular to the maximum principal stress directions; an anomalous parallel relationship exists at a test site in an intrusive rock body. The results suggest that the open microfracture subfabric may provide a means for gaining information on the directional properties of stress fields. Such information can be obtained from oriented cores taken from holes which exceed the approximate 100-foot depth to which other in situ methods are presently limited.

Jan 1, 1970

By William D. Monaghan, Thomas H. Dubaniewicz, Kenneth L. Cashdollar

Emerging laser technologies are quickly gaining acceptance in the industrial workplace. Besides the risk of human exposure, one safety concern with the more intense lasers is the potential for ignition of flammable gases, vapors, dusts, fibers, or flyings often found in hazardous (classified) industrial settings. In underground coal mines, lasers are being considered for remote measurement of explosive methane gas. Current federal safety regulations for underground mines contain no specific guidance for evaluating the safety of optoelectronic components such as diode lasers. The National Institute for Occupational Safety and Health is conducting research to help provide a scientific basis for developing appropriate safety guidelines for optical equipment in the presence of flammable methane gas and/or coal dust. One phase of the study is an experimental evaluation of methane-air ignition by laser heated small particles. Minimum observed igniting powers for laser energy delivered by 200-, 400-, and 800-um core diameter fiber optic cables and directed onto selected targets in methane-air atmospheres were 0.6, L l, and 2.2 W, respectively. Comparisons are made with other ignition phenomena, including heated wires.

The largest producing coal field in Alabama, the Warrior Coal Field, was discovered in 1821&apos;. Since then, coal has become Alabama&apos;s leading industrial mineral, both in production and income. Alabama has traditionally been one of the nation&apos;s major coal-producing states. This level of production is expected to continue due to Alabama&apos;s high-quality, low-sulfur coal. Alabama produces both bituminous and lignite coal. The bituminous coal is mined by underground and surface methods from four major coal fields in 24 counties. Alabama&apos;s lignite deposits, which are located in the southern part of the state, are not presently being mined. However, Alabama lignite is high-grade, and deposits are very shallow and easily surface-mined. Alabama gained primacy when its regulatory program was conditionally approved May 20, 1982. The program was fully approved July 5,1984. Alabama&apos;s Abandoned Mine Lands program was approved May 20,1982, and its emergency program was approved January 23, 1991. Although a Federal Lands Cooperative Agreement between Alabama and OSM became effective August 30,1985, no coal mining is currently taking place on federal lands in the state.9

Jan 1, 1992

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under parent regulations may not limit cable temperatures to less than 90 °C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, ell carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine foes. This paper describes a method of measuring the conductor temperature of untie trailing cables during no anal operation. The temperature is measured using a 50/175 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements arc made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA&apos;s Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

By Edward A. Mihok

Laboratory batch-flow tests conducted on a highly ferruginous acid mine water with an activated carbon showed that ferrous iron is rapidly oxidized. This indicates that air oxidation of ferruginous acid in mine waters is catalyzed by activated carbon. The ferrous iron content of an acid mine water flowing through an aspirated activated carbon column was reduced from about 700 to about 10 parts per million in less than 1 minute. Highly efficient ferrous iron oxidation was achieved by conditioning the activated carbon by repeated treatment with acid mine water and air. The reaction proceeds rapidly in the acid environment (pH about 2.5) engendered by ferrous iron oxidation. The activated carbon was used repeatedly with little loss in efficiency, no discoloration, or solids deposition. In these batch tests, about one-third of the iron was adsorbed by the carbon, but with continuous flow, little iron adsorption is expected. Incorporating a catalytic oxidation step in the treatment of acid mine waters containing ferrous iron would greatly facilitate neutralization--precise control of pH, lower reagent costs, elimination of aeration equipment, and smaller holding ponds.

Jan 1, 1969

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976