Search Documents

By J. R. Thoenen

[Since the publication of the preliminary report on this subject in July, 1927, (The Wire Saw in Slate Quarrying, Preliminary Report, Serial No. 2820, by Oliver Bowles) the wire saw has been in constant daily operation at the quarry of the Colonial Slate Company. Luring this time between twenty end thirty successful cuts have been made varying in length from forty-five to ninety-two feet and in depth from six to ten feet. No accurate time records have been kept on these cuts but they have totaled over 12,000 sq. ft. of area and required 19,000 lineal fact During these cuts the average speed of cutting has risen from the 12.8 sq. ft. per hour obtained in the original recorded tests to between 15 and 20 sq. ft. per hour, with the present rate running very close to 20 sq. ft. per hour at this quarry.]

Jan 1, 1928

By James W. Vogh

The report covers initial findings in an experimental program to identify diesel exhaust odorants and determine their contributions to diesel odor. The approach was to isolate selected component groups from exhaust and to evaluate the contribution of each group to exhaust odor. Results were obtained for those carbonyls and phenols that could be isolated from exhaust through inter-mediate conversion to oxime derivatives. Unsaturated aliphatic aldehydes and sterically hindered carbonyls were not included. Hydrocarbons intermediate in the diesel range were "also evaluated and an odor contribution was found from those of the aromatic group. The evaluated carbonyls, phenols, and hydrocarbons were found to account for about 20 pct of the total odor in exhaust from an indirect-injection engine during idle. For exhaust from the indirect-injection engine operating under load and from a direct-injection engine at no load, these compounds were found to have no significant levels of odor.

Jan 1, 1972

By M. D. Schlesinger

Experimental data for coal hydrogenation are presented to show that when a vehicle oil produced from coal is present, coal is hydrogenated to the same high conversion whether molybdenum catalyst is impregnated on the coal or intimately mixed with the slurry. Differences in product distribution could be related to the severity of operating conditions. No minimum mixing time was established, but 2 hours was sufficient. Longer periods of mixing, to 14.75 hours, had no effect on the results. The hydrogenation conditions were in the pressure range of 8,500 to 10,000 p,s,i. at 400° to 500° C. Most of the experiments were made in duplicate. The results were obtained with molybdenum concentrations of 0.01, 0.1, and 1 percent. Al the mentioned pressure range and a time at temperature of 15 to 60 minutes, coal conversions higher than 98 percent were obtained.

Jan 1, 1962

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

By d&apos, Kathleen J. Amico

THIS SUAMMARY is shown in Minerals Yearbook volumes I and III of this series on mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and ex- ported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1962

By D. R. Flinn

The Bureau of Mines has studied the electrochemical parameters important to the preparation of coatings of the platinum-group metals. Using molten mixtures of sodium and potassium cyanides in an inert atmosphere, techniques have been developed that permit the preparation of baths for platinum, rhodium, and iridium electrodeposition. Cyclic voltammetric and slow sweep rate linear polarization techniques have been utilized to determine optimum potential and current values for preparation of plating baths and for the electrodeposition of coatings. Techniques are described for the deposition of platinum and rhodium coatings at near 100 percent anode and cathode current efficiencies, and for iridium at approximately 80-percent efficiency. Palladium deposition from these molten cyanide baths remains un-satisfactory. The chemistry of the palladium-containing cyanide bath is discussed. Examples of scanning electron microscope photomicrographs of typical platinum coatings are presented. Techniques are described for the preparation of platinum coatings on large objects.

Jan 1, 1982

The Technology Transfer Seminar on Mine Communications held on March 21-22, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

By J. J. Bourquin, S. H. Katz

"Three types of respiratory apparatus namely, gas masks, hose masks, and self-contained oxygen-breathing apparatus - are now commonly used for protection from noxious gases, vapors, and smokes or ristes, but no particular type can be selected as best for all conditions. Many factors must be considered in connection with each situation, so that each must be considered as a problem in itself. Following are concise statements for comparing the types:Gas masks are the simplest and easiest to wear, also the least cumber-sore; but they protect only in comparatively low concentrations of noxious gases and should never be used where the air contains less than 16 per cent of oxygen. Special masks give protection from one gas or class of gases, but may give no protection against another gas or class of gases.Hose masks protect in any irrespirable atmosphere, but are somewhat cumbersome, the length of hose limiting the distance a wearer may go from fresh air. They are serviceable also where a supply of pure air moves with the wearer, as where a locomotive engineer in a smoky tunnel is using a hose mask supplied with air from the compressed air line of the locomotive. Hose masks consume no chemicals or materials and so are not limited in the time they may be used.Self-contained oxygen-breathing apparatus protect in any irrespirable atmosphere, but their weight is cumbersome, they can be used only by trained men, and frequent attention must be given them to maintain good working condition. On the other band they are the only safe means for exploring mines and other places filled with irrespirable gases in high concentrations."

Jun 1, 1923

By Joseph W. Town

The Bureau of Mines conducted studies related to SO2 air pollution to determine attritioning rates, SO2 sorption rates, and sulfur loads that could be obtained on commercial alkalized alumina sorbent pellets. Fluidized-bed attritioning rates ranged from 0.025 pct/hr for alkalized alumina with a crushing strength of 4 kg to 0.075 pct/hr for 0.5 kg crushing strength mate¬rial. Airlift attritioning rates ranged from 0.50 pct/hr for 3 kg crushing strength alkalized alumina to about 3 pct/hr for 0.5 kg material. Attritioning rates for the commercial alkalized alumina were comparable to those obtained for sorbent pellets prepared in the Bureau of Mines laboratory. Sorption rates were related to S02 concentration in flue gas, temperature, and presence of nitrogen oxides in the gas stream. Sorption rates at 300° C were 0.35 X 10-6 gS/gp/sec (grams sulfur per gram pellet per second) in 0.045 pct so, gas, 5.1 x 10-5 gS/gp/sec in 0.34 pct SO2 gas, and 65 X 10-5 gS/gp/sec in 10 pct SO2 gas. For the 0.34 pct S02 gas, sulfur loads of 0.10 gS/gp (the projected load for regeneration) were obtained in 47 min at 130° C and in 116 min at 300° C. The presence of either NO or NO2 in the 0.34 pet S02 gas increased the SO2 sorption rates 2 to 3 times at 300° C, but had no effect at 130° C.

Jan 1, 1969

By Charles T. Chislaghi

An economical, remotely operated (automated), temporary roof support (ATRS) has been developed by the Bureau of Mines for use on a single, fixed-head roof-bolting machine (squirmer) that operates in low coal seams (less than 42 in thick). The ATRS eliminates the need for squirmer operators and helpers to go under unsupported roof to set or remove temporary support prior to or during the roof-bolting cycle--a task that annually accounts for approximately 20 pct of all roof fall fatalities. The ATRS can be adapted to any squirmer used in the U.S. low coal fields. A prototype ATRS was field-tested at Imperial Colliery Co.?s Mine No. 20 in Eskdale, W. Va. The Mine No. 20 amended roof- control plan, which requires the use of the Bureau?s ATRS as temporary support during face bolting, has been approved by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor.

Jan 1, 1982

By Robert S. Sanford

The Broughton and Ring magnetite deposits in Essex County, N. Y., are thought to be in a mineralized belt that extends from the Lake Sanford mining district to Lake Champlain and passes through the Mineville district. The country rook is syenite-gneiss, similar to that in the Mineville area. The Bureau of Mines conducted a vertical magnetometer survey of the area. On the Broughton properties there are no indications, magnetically, of magnetite in any degree of concentration. 'On the ding properties a number of sharp, localized magnetic anomalies were observed. One core-drill hole was bored to a, depth of 48.3 feet, also, to test one of the strongest anomalies. The field work was in progress from December 1943 to July 1944. Although no iron ore was intersected by' the drill hole, it showed that the amphibolite rook, at a depth of 6 to 100 feet below the surface, contained enough magnetite and iron sulfides to account for the anomalies recorded by the magnetometer survey.

Jan 1, 1949

By Joseph E. Matta, John C. LaScola, Fred N. Kissell

The Bureau of Mines investigated coal storage silos to determine how gassy coal must be for methane accumulations in a silo to become hazardous and where such accumulations are likely to occur. Methane concentrations were measured in the open space above the stored coal pile, in the pile, and in the reclaiming area. No methane layering was found in closed-top silos. Reclaiming areas were as gassy as the top part of the silos. Coal samples were collected from the conveyors entering the silos in order to assess the gassiness of the coal. No simple correlation was found between the gassiness of the coal stored and the measured methane concentrations. However, at mines where the average 24-hour gas emission from the conveyor belt samples was 14 ft3/ton or more, fans or open tops were used. It appears that a large fraction of the methane released during storage remains in the void space between the coal particles.

Jan 1, 1981

To provide a method for locating trapped miners promptly and accurately. The Approach: Develop a wireless emergency system that is intrinsically safe, compact, easy to operate, reliable, sturdy, and economical. How It Works: A (one transmitter has been developed under Bureau of Mines contracts. The transmitter weighs only a few ounces, is powered by a cap lamp battery, arid can be carried on the miner's belt. A compact loop antenna, which could either be carried by the miner or strategically located in the mine, is used to generate a magnetic field that is sensed by a mobile receiver on the surface. When needed, the antenna is deployed to form a single loop. In mines where the overburden is less than 600 feet, a loop of No. 19 wire approximately 30 feet in circumference is normally adequate. This antenna weighs less than one half pound. In deeper mines, a heavier wire and bigger loop is required; a No. 10 wire deployed around a pillar has been used.

Jan 1, 1974

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Ahmed, M.,• "Development of an Integrated Control System for Mine Ventila¬tion and Firedamp Drainage," Mining Engineer, Vol. 127, No. 91, April, 1968, pp. 382-392. Andrews, J. W., "U. S. Mine Ventilation Standards," Paper presented at the International Mine Ventilation Congress, Sept., 1975. Boyle, J. A., and Conn, 0. S., "The Control of Mine Ventilation Utilizing Multiple Main Fans," Paper presented at the Seventy-second Annual CMIA Meeting, Pittsburgh, December 1958. Collinson, P. L., and Vance, W. E., "Mine Ventilation Planning," The Mining Engineer, Volume 121, No. 14, 1961, pp. 141-156. Committee on Industrial Ventilation, Industrial Ventilation, 12th Edition, 1972. Grever, R. E., "Automatic Monitoring of Ventilation Conditions in European Coal Mines," Symposium on Engineering Systems Design for Mine Safety, Michigan Technological University, August 1973. Hall, C. J., Airflow in Mines - Thermodynamic and Motive Column Analyses, The Book Concern, Printers, Inc., Hancock, Mich., 1967, 263 pages. Hargraves, A. J., "Planning and Operation of Gaseous Mines," Canadian Mining and Metallurgical Bulletin, Vol. 66, No. 731, March 1973, pp. 119-128. Harris, E. J., "The Fluid Network Analyzer as an Aid in Solving Mine Ventilation Distribution Problems," SME-AIME Transactions, Vol. 228, 1963, pp. 391-395 Higgins, J., and Shuttleworth, S. E. H., "A Tracer Gas Technique for the Measurement of Airflow in Headings," Colliery Engineering, November 1958, Vol. 35, pp. 483-487. Kaiser, K. M., and Bhowmick, B. C., "Recent Developments in Mine Ventila¬tion Instrumentation," Journal of Mines, Metals & Fuels (INDIA), June 1974, pp. 155-162. Kalasky, J. D., and Krickovic, S., "Ventilation of Pillared Areas by Bleeder Entries, Bleeder Systems, or Equivalent Means," Trans¬actions AIME, Volume 254, December 1973, pp. 284-291. Mahajan, J. K., "Ventilation Planning for a Deep Metal Mine," Min. Geol. Met. Inst. India, Volume 69, 1972, pp. 31-38.

Jan 1, 1977

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Air Moving and Conditioning Association, Fan Application Manual Part 1, Fans and Systems, AMCA Publication 201, 1976a. Air Moving and Conditioning Association, Fan Application Manual Part 2, Troubleshooting, AMCA Publication 202, 1976b. Air Moving and Conditioning Association, Fan Application Manual Part 3, Field Performance Measurements, AMCA Publication 203, 1976c. Air Moving and Conditioning Association, Directory of Products Licensed to Bear the AMCA Certified Ratings Seal, Edition 27, August 1, 1975. Allan, A. L., Hollwey, J. R., and Maynes, J. H. B., Practical Field Surveying and Computations, American Elsevier Publishing Co., Inc., New York, 1968. American Society of Heating Refrigeration and Air Conditioning Engineers Std. 51-75, Air Moving and Conditioning Association Standard 210¬74, Laboratory Methods of Testing Fans for Rating. Anderson, T. C., and Nugent, J. W., "Mine Ventilation Pressure Differentials with a Programmable Hand Calculator," MESA Informational Report 1050, 1977. Atkinson, J. J., "On the Theory of the Ventilation of Mines," Trans. N. E. Inst., Vol. 3, 1854, pp. 118. Barnes, E. L. S., "Mine Ventilation Network Analysis," International Mine Ventilation Congress, Marshalltown, S. Africa, Sept., 1975. Boshkov, S, and Amontree, B., "How Operator Proximity Affects Anemometer Readings," Coal Age, Vol. 55, No. 5, 1950, pp. 85-56. Boshkov, S., and Wane, M. T., "Errors in Underground Air Measurements," Mining Engineering, Vol. 11, No. 7, November, 1955, pp. 1047-1053. Briggs, H., "The Underground Leakage of Air, Investigation of the Porosity Coefficient," Transaction of the Institution of Mining Engineers, Vol. 82, pp. 111-121. Brown, J. R., and Hinsley, F. B., "The Flow of Air in Bends and Straight Airways," Transaction of the Institution of Mining Engineers, Vol. 116, July, 1957, pp. 845-867. Burrows, J., "Measurement of Fan Pressures," Journal of the Mine Ventila¬tion Society of South Africa, Volume 27, No. 4, April 1974, pp. 57-63.

Jan 1, 1977

By Maria I. De Rosa

The U.S. Department of Energy Pittsburgh Research Center2 conducted experiments with mine conveyor belt samples in a 20-L furnace and in a laboratory fire tunnel to measure and compare the major toxic gas concentrations evolved during the combustion of the materials. The toxic gas concentrations, measured simultaneously through a multiport sampling device and treated as yield values, included hydrogen chloride (HO), hydrogen cyanide (HeN), oxides of nitrogen (NO, treated as NO), and carbon monoxide (CO). The data obtained from the two experimental systems were in good agreement. Correlations were developed for the toxic gas yields as a function of the percentage of chlorine (for HO gas), nitrogen (for HCN and NO, gases), and carbon (for CO gas) contained in the original materials. The toxic gas yields were also used to calculate a toxicity index (TI) parameter to assess the potential gas toxicity of belt materials during a fire. Furthermore, the TI and the mass loss burning rate values were used to calculate a toxicity hazard (TH) parameter to estimate the toxic gas hazard produced by a burning belt in a ventilated system. Results show that polyvinyl chloride (PVC) belts released higher HC1 concentrations because of the higher chlorine content; styrene-butadiene rubber (SBR) belts released higher CO, HCN, and NOz concentrations because of the higher carbon and nitrogen contents. The TI's, however, were greater for the PVC belts due primarily to the higher levels of HC1 produced. The fire tunnel data indicate that the SBR belts can bum with higher mass loss rates than the PVC belts, resulting in a potentially higher toxic hazard (higher TH values) even though their TI values were lower than those of the PVC belts.

By C. W. Davis

"A copper-palladium-gold-silver ore is being mined at Salt Chuck, Prince of Wales Island, Alaska, from which a concentrate is produced that contains 40 to 50 per cent copper, and considerable amounts of palladium, gold and silver. There has been much difficulty in obtaining assays for palladium, gold and silver from the mine, smelter, sampler, and umpire that check within reasonable limits. While the results for copper content have not been unusual, the results for palladium have varied as much as 0c8 oz. on 3 oz. material, results for gold differed by 0.1 oz. on 1.6 oz. materials, and for a silver content of 7 oz., results differed by as much as 4.0 oz.The Bureau of Mines was requested to determine the causes of variation in the results of the different assayers, and to develop a satisfactory procedure for analyzing such ore.Three samples of concentrate were received for analysis, two small lots that had previously been assayed by the various laboratories, and one large sample. The large sample was dried and ground in a ball mill, put through a 150-mesh screen, and then returned to the ball mill for thorough mixing. The small samples were ground to pass a 150-mesh screen and then mixed on a mixing wheel.The large sample (No. 1) was analyzed by five different procedures, one of the small samples (No.2) by three procedures, and the other (No. 3) by two procedures (the two small samples being too small for further tests). The different procedures tried and the results obtained arc presented below. The samples of concentrate were from ore mimed and milled by the Alaska palladium Co. at Salt Chuck."

Feb 1, 1926

By S. H. Katz

"At the annual meeting of the International Association of Fire Engineers at Kansas City, Mo., in June, 1919, the Bureau of Mines offered to cooperate with municipal fire departments for the purpose of obtaining information regarding composition of the air in burning buildings. (Katz, S. H., Statement made at Convention of International Assoc. of Fire Engineers: Fire and Water Eng., vol. 66, July 16, 1919, pp. 129-30, also Fireman's Herald, vol. 78, July 12, 1919, pp. 48.) The gas-mask laboratory of the Bureau's experiment station at Pittsburgh sent vacuum bottles for taking samples to fire chiefs in twenty-five cities, who had signified their intention to aid in this work. It was hoped to obtain one hundred or more samples, because statistics in quantity are necessary for drawing reliable conclusions concern-in the likelihoods of encountering irrespirable as in burning buildings. This far, eleven samples have been received by the laboratory. Results of analyses and pertinent data regarding these samples are given in the accompanyingEight of the eleven samples contained, no carbon monoxide; seven of the eight were taken above the ground level and one below ground. One sample taken above ground contained 0.03 per cent carbon monoxide, and this quantity is not dangerous to breathe for a limited time. Of the three samples taken below ground, one contained no carbon monoxide; the other two contained 0.10 and, 0.35 per cent, respectively. This indicates that in a burning building, the hazard from carbon monoxide is much greater below the ground level. The cause undoubtedly lies in the poorer ventilation that is usually found in cellars or basements. Abundance of ventilation provides the necessary air for complete combustion, or if incomplete combustion does occur, the carbon monoxide generated by the fire is greatly diluted with fresh air and swept away by the current. It may be noted that the highest proportion of carbon monoxide was found in a cellar where a fire as burning among piled cases. The difficult access of air to the burning parts facilitated the formation and lib ration of carbon monoxide. The smoke here was very light and no difficulty was experienced in breathing. Some of the air containing dense smoke showed little change from normal air by analysis. Thus the density of smoke or the irritation and difficulty it causes in breathing are no indication of the presence of poisonous gas. None of the samples shows important oxygen."

Nov 1, 1920

By Walter C. Lorenz

Samples of materials containing pyrite from various coal mines and coalbeds were studied to compare their compositions and oxidizing characteristics. Pyrite was the only form of iron sulfide identified, but X-ray diffraction, emission spectrography, and microscopic analyses revealed similar suites of minerals and trace elements. The pyrite occurred usually in spherical clusters of very small crystals. The oxidation of pyrite in solutions of PeSO4 and Fe2(SO4)3 and in the presence of an iron oxidizing bacterium Ferrobacillus ferrooxidans, was studied through a manometric technique. FeS04 or Fe2(SO4)3 solutions had no appreciable influence on pyrite oxidation under the test conditions, The bacterium acted as a catalyst, greatly increasing the oxidation rates; however, in three samples that also contained calcites, bacterial oxidation was greatly reduced. The oxidation rates also increased approximately as the percentage of pyrite in the samples increased. For the series of samples studied, there was no definite correlation of the results with the location of the various mines nor with the acidity of alkalinity of the mine drainage.

Jan 1, 1963