Search Documents

By Lester J. Crow

A preliminary survey was performed to investigate the impregnation of relatively weak, porous volcanic tuff and a relatively strong, dense sandstone with five different monomers. Increases in compressive strengths by factors of 2 to 5, and elastic moduli by factors of 2 to 3.5, are reported for natural rocks (tuff., sandstone, dacite), which were impregnated with five monomers (methyl methacrylate; chlorostyrene; 40 percent TMPTMA-60 percent styrene; 40 percent TMPTMA-60 percent chlorostyrene; 60 percent polyester-40 percent styrene); polymerization took place after monomers were forced into the rock. Impregnation was performed (1) by pressurizing rock specimens from one end, or (2) by a vacuum-soak operation. Polymerization was accomplished by either radiation or chemical initiation techniques. Strength improvement is dependent on (1) the type of monomer used, (2) the amount of polymer incorporated into the rock, and (3) the degree of water saturation of the rock. Water saturation strongly reduced the effectiveness of the method for the polymer systems tested. The more viscous monomers (for example, 60 percent polyester-40 percent styrene) were more effective in displacing the water from the rock, and compressive strengths of wet rock were doubled with these systems. Water saturations ranging from 25 to 100 percent of maximum saturation gave essentially identical results. Further tests on other types of mine rock; including shale and coal, are planned. Water-compatible polymer systems should be developed, or present systems should be suitably modified. For application to tunnel stabilization, design studies evaluating the improvement in rock strength and its influence on the support system are also recommended.

Jan 1, 1971

By Raymond P. Maloney

The Bureau of Mines investigated the White Mountain mercury deposit, in the Kuskokwim River Basin, to better determine the extent of mercury mineralization and to encourage its development by private industry. A program of diamond drilling, augering, bulldozer trenching, and sampling was carried on during four field seasons, from 1960 to 1963, inclusive. Significant amounts of cinnabar, with only trace amounts of arsenic and antimony, occur in dolomite over an area about 4,000 feet long and 1,500 feet wide. The deposit differs from other mercury deposits in the Kuskokwim River Basin by the absence of silica-carbonate and rhyolite intrusives. Small-scale mining was started in 1963 as the result of Bureau investigation and continued during the summers of 1964 and 1965. The investigations indicate that open pit mining might be the most feasible method of working this deposit.

Jan 1, 1967

By J. Pasini

The Bureau of Mines has investigated novel methods of stimulating petroleum production from reservoirs in the Appalachian Region. An important consideration in applying stimulative production methods is the control and removal of solid precipitates from the boreholes of production wells. Where paraffin-base crude oils are produced, as in the Appalachian Region, the accumulation of paraffin may be particularly troublesome. Paraffin deposition is a major production problem that has confronted the petroleum industry for many years. Although considerable effort has been expended by industry and government, a suitable solution has not been found because of the individuality and complex nature of the deposits. Remedial methods used to prevent or remove paraffin fall generally into four classes: (1) Chemical, (2) physical, (3) operative, and (4) combination. Each class has many subclasses that apply to particular problems in different oil- producing areas. Recently, chemical inhibitors and the sonic pump have assisted operators in preventing and removing paraffin deposits. Because these methods are relatively new, their degree of application has not been completely evaluated.

Jan 1, 1963

By Carlton E. Brown

Broom and Yant6/ recently described a. microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter) and the thermal precipitator8/ . This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a micrcprojection method for counting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the ventilation Department of the Anaconda Copper Miring Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By T. A. Evans

The Bureau of Mines conducted a Laboratory and pilot-plant investigation of the flotation of iron sulfides from zinc-lead mill tailings near Platteville, in south-western Wisconsin, at the North Central Experiment Station, Minneapolis, Minn. The procedures used and the results obtained in this investigation are described in this report. Samples for laboratory tests were obtained from each mill in the district, namely, Calumet & Hecla, Inc., Eagle-Picher Co., Vinegar Hill Zinc Co., and Tri-State Zinc, Inc. The sample fat pilot-plant work was obtained from the Davis Mining Enterprises mill.

Jan 1, 1957

By Carlton E. Brown

Brown and Yant6/ recently described a microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter7/ and the thermal precipitator8/. This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a microprojection method for courting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the Ventilation Department of the Anaconda Copper Mining Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau's measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau's investigations. Typical comparative data are included.

Jan 1, 1986

"INTRODUCTION These safety standards for anthracite mines have been prepared for use as a guide for Federal inspectors. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7282 issued in May 1944 and used as a guide in Federal inspections. No provision made in these safety standards should be construed or operate to nullify any existing State statutes; they are intended to supplement the State statutes in the interest of increased mine safety. Mines are inspected in accordance with the Federal Coal-Mine Inspection and Investigation Act of 1941, Public Law 49, 77th Congress, H. R. 2082. Any unusual hazard noted by an inspector and not covered by these standards will be discussed in the inspection report, and suitable remedial procedure will be recommended.ARTICLE I. - SURFACE STRUCTURESSection 1. Breaker and cleaning plant.Electric switches and controls in breakers and cleaning plants should be enclosed.Where coal is dumped at or near air-intake openings, reasonable provisions should be made to prevent the dust from entering the mine.Section 2. Lamp houseNaphtha or other flammable liquids in lamp houses should be kept in approved containers or other suitable dispensers.Flame safety lamps should be permissible and maintained in permissible condition.Flame safety lamps should be properly cleaned, examined, and assembled by a qualified lamp attendant or other competent person before each period of use. Lamp assembly should again be checked by the person using it immediately before he enters the mine.When not in service, methane indicators, flame safety lamps, and electric cap lamps should be in the custody of competent persons responsible for maintenance and testing."

Feb 1, 1948

By Danton L. Paulson

Elevated temperature electrical resistivity measurements were made by the Bureau of Mines on arc-melted, spin-cast, and hot-pressed columbium carbide¬carbon (CbC-C) and zirconium carbide-carbon (ZrC-C) materials up to 2,000° C. The CbC-C materials displayed electrical resistivity values ranging from 35.20 microhm cm at 23° C for hot-pressed material containing 12 wt pct carbon to 242.64 microhm cm at 1,622° C for arc-cast material containing 17.0 wt pct carbon. Electrical resistivity values ranged from 29 microhm cm at 20° C for arc-cast ZrC-C containing 16 wt pct carbon to 279 microhm cm at 1,951° C for hot-pressed ZrC-C containing 21 wt pct carbon. Data from a previous report were included to establish comparison between the electrical resistivities of the CbC-C, ZrC-C, and HfC-C systems.

Jan 1, 1969

By Robert K. Koch

The Bureau of Mines investigated separating HF from HF-SiF4-H2O mixtures by passing the mixed gases through a sodium fluoride slurry in an airlift scrubber and forming a mixed precipitate of NaHF2 and Na2SiF6. The oven-dried precipitate was thermally dissociated in two stages. The first stage was carried out at 400° C and dissociated NaHF2 to NaF and HF. Condensation and analysis of the evolved HF proved it to be 97 to 99 weight-percent HF containing 0.79 to 0.99 weight-percent H2O and 10 to 93 ppm silicon. The second stage was carried out at 700° C and dissociated Na2SiF6 to NaF (for recycle) and SiF4. The quantity of HF recovered from gaseous HF-H2O-air mixtures decreased with increasing relative H2O concentrations. Air was beneficial when scrubbing extremely dilute wet HF gases. At HF partial pressures of 0.24 and 0.013 mm Hg in the scrubber entrance gases, HF partial pressures of 6.2 x 10-4 and 9 x 10-6 mm Hg were obtained, respectively, in the scrubber exit gases. Scrubber efficiencies were 99.7 and 99.3 percent.

Jan 1, 1966

By Chester L. Arnold, Reinhardt Thiessen, Alexander Lowy

"INTRODUCTION Peat is the accumulated mass of plant materials that remain after partial decay under specific conditions. In the swampy peat bogs dead material which falls on the surface immediately is attacked by fungi and aercbic bacteria. Decay under these conditions is rapid, but of relatively short duration, since the constant addition of new material soon forces the older layers below the water level, in this position, without access to oxygen, the plant constituents are attacked mainly by anaerobic bacteria, and decomposition proceeds slowly. The largest part of peat is contributed by the woody tissues of plants, the chief constituents of which are cellulose and lignin, together with a small proportion of hemicelluloses. During the normal process of biological decay celluloses disappear more rapidly than lignin. The result is a complex substance known as humin, from which the humic acids may be extracted.In 1826, Sprengel 5 found that when decayed plant materials were extracted with alinnli and the resulting black liquid acidified with mineral acid a brown gelatinous precipitate was formed. To this product, which was a brown amorphous powder when dry, he gave the name ""humic acid'. Since that time, chemists have used the name rather loosely to designate products which have been isolated by very diverse means from soils, decayed woods, peat, lignite, and coal. An excellent review of the early work on humic acids was published by Baumann 6 in 1909. This publication aroused the interest of Oden, who then investigated the humic acids. An account of Oden’s work, as a good survey of the literature, is contained in his monograph “Die Huminsauren”. 7"

Nov 1, 1934

By Adrian J. Mathias

This report presents the results of an investigation of a mine production-scheduling model and a critical path analysis for long-range mine planning. An example is given to illustrate how these techniques might be used to plan long-range development and production scheduling for a large underground mine. The model, based on estimated ore block grades and tonnages, and on designed mine development layout, simulates mining of ore blocks in a sequence necessary to fulfill mill requirements for ore tonnage and grade evaluation within pre-established system restrictions. Simulated production schedules are obtained as output from the model. These production schedules are then incorporated into a critical path analysis to determine the sequence for the long-range development work so as to fulfill the production schedules and thereby meet the ore grade and tonnage requirements of the mill.

Jan 1, 1967

By P. L. Sibrell

Electrorefining of Ti in nonaqueous solvents has been studied by the U.S. Bureau of mines as a method for recycling impure scrap Ti. Electrochemical behavior of Ti species was investigated using cyclic voltammetry. Research results showed that Ti metal can be dissolved in polar solvents such as dimethylformamide or dimethyl sulfoxide. However, deposition of Ti from these solvents was not successful. Several solvent systems were investigated for electrodeposition of Ti but no deposits were obtained. Reduction of Ti4+ complexes to Ti3+ proved to be straightforward, but reduction to lower oxidation states could not be confirmed. In dimethylformamide solutions, cyclic voltammetry results demonstrated the reduction of Ti to an oxidation state of less than three, but no Ti metal was identified. In dimethyl sulfoxide solutions containing LiCl, it was possible to deposit Li metal. After adding Ti salts to the solution, electrolysis quickly passivated the electrode. Deposition of Ti was also investigated in solutions of dimethoxyethane and propylene carbonate but, again, no reduction of Ti to oxidation states of less than three occurred. Therefore, the prospects for a nonaqueous electrorefining system for Ti metal do not appear promising.

Jan 1, 2010

By W. F. Netzeband

This paper, which describes mining methods and practices at the Rialto zinc-lead mine American Zinc, Lead & Smelting Co., in northeastern Oklahoma, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States, The Rialto mine is in the SE1/4 SW1/4 sec. 20 and the NW1/4 sec. 29, T. 29 N., R. 23 E., Ottawa County, Okla. (fig. 1). The 200-acre property is southwest of and adjacent to the town of Picher in the central part of the Picher field of the Tri-State zinc-lead mining district (fig. 2). Other mines of the company adjoin the Rialto on the east and south. Zinc-lead ores have been mined almost continuously from the Rialto tract since 1916. The property was acquired by American Zinc, Lead & Smelting Co. late in 1951, and the mine was operated thereafter by the Nellie B Division of that company until the end of 1955, when it was subleased to the Residue Mining Co.

Jan 1, 1958

By David E. Fogelson

The breakage of rock by explosives depends largely on the ability of an explosive to transfer its stored potential energy to the rock as strain energy. Therefore, the relative rock-breaking abilities of explosives can be determined indirectly by determining the relative amounts of strain energy transferred to the rock at the time of detonation. This report presents experimental data on the strain energy contained in explosion-generated strain pulses in a granite gneiss. Six explosives were tested. The scaled total radial strain energy Es/W flowing outward through a spherical shell of scaled radius R/W1/3 surrounding the point of detonation was found to follow an exponential decay propagation law of the form [ ]

Jan 1, 1959

By R. V. Higgins

A computer program is presented to calculate the shape factors and volumes of cells from a potentiometric model, using coordinates of the inter-sections of the stream lines and equal potentials and a few additional coordinates. Shape factors are used in flow computations when the geometry is complicated. The program also includes computer instructions to divide the channels into cells of equal volume and to obtain the shape factor for each of these equal volume cells. An illustrated example using the potentiometric model for the waterflood of a seven-spot well-spacing pattern is presented. The information contained in the report is of value not only to those allied to the subject but also to others, because many of the techniques can be conveniently used in formulating other computer programs.

Jan 1, 1966

By K. J. Miller

A laboratory electrophoresis column was designed to separate pyrite from fine coal by utilizing an observed difference in the electrophoretic mobilities of the two materials in water. The apparatus worked well when tested with synthetic mixtures of coal and pyrite, but some modifications in design and procedure were necessary to provide a sharper separation. After these changes were made, the column was tested with a high-pyritic-sulfur raw coal sample. The column successfully fractionated the sample, removing not only the pyritic refuse, but a siliceous refuse as well. The invest ion demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis.

Jan 1, 1970

By A. Gene Collins

Rapid, sensitive, and precise methods of determing major, minor and trace constituents of oilfield brines are needed. Several methods have been developed or adapted by the Federal Bureau of Mines at the Petroleum Research Center, Bartlesville, Okla. The following methods are described in this report: Spectrophotometric and volumetric for iodides and bromides; potentiometric for pH, alkalinity, acidity, borate boron, total boron, and organic boron; gravimetric for potassium; disodium ethylenediaminetetraacetate (EDTA) volumetric for total hardness, calcium, and magnesium; spectrophotometric for fluorides; and color comparison .for arsenic. Adequate sensitivity, precision, and accuracy were obtained for each method. The Bureau of Mines pioneered in research on the analysis of oilfield waters (2, 46, 47).6 However, several of these early procedures were quite time consuming. Also, they did not include methods for determining trace and minor constituents of brines.

Jan 1, 1961

By Donald W. Mitchell

Certification tests for urethane-foam systems and techniques for apply-ing foam safely in mines are described. Fire hazard from foam exists if flame propagates beyond the ignition source or penetrates the foam. Foam that passes the certification tests can be applied on stoppings, continuous sections of ribs of relatively wide passageways (with no foam on the roof), short sections of roof such as overcasts, roof cavities, and intersections (with no foam on the ribs), and between buntons on one wall of a shaft. Foam on the ribs and adjoining roof presents a fire hazard. Stoppings covered with foam passing the certification tests are resistant to penetration of heat, flame, and smoke than similar stopping without foam. Flame propagation can be arrested by water sprays. Spontaneous ignition of foam can be prevented.

Jan 1, 1966

By H. R. Babitzke

To develop alloys suitable for use at elevated temperatures, columbium and tantalum were combined with tungsten, hafnium, vanadium, zirconium, and titanium, and the resulting alloys were evaluated with respect to fabricability, hardness, Electrical resistivity, strength at elevated temperatures, oxidation resistance, and bend transition. Of the 23 compositions tested, Cb-2OHf-5W-10Ti exhibited superior high-temperature properties. A recrystallized sample of this alloy was fabricable at room temperature, had a strength of 44,000 psi at 1,200° C, and had an oxidation rate of only 7.7 mg/cm2/hr at 1,000° C.

Jan 1, 1966