Search Documents

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By J. C. Fowler

[This i.untra t hds bmii III c'IIILt fur till- past 1':?:u yrlr;, Till-- wurir pnrfor rw:it '. ,JS hlui.rn dawn Ilttf lit Iu i eel i ih?IS( S. 1 hesrt aIII, Phase I Candor tlri I a lest It) donurnSlrale SeiSrrlir nurihudS to hu USi!d lot ttlr? rti?tei thin and Iu" ainnl ul trapped rrlinc:rs hitting (-)it the roof with a harnrner, Phase I' Design and cunStrur.t a permanent Seismic monitor System to rrlunrtur roof (ails arm r:xploslun', III ,r 'Vol king mine. Phase III - Ire dII an an i i irr for sVstl rtl Ii i`'Smltur air quality in till, niitii iiH II ? ir,iti tin; niln !III ;I I ,, i; Phase I V - Conduct 11(21 d tests of the seismic IT IUnit UT ieq system fur a period nl two 11IUIIIIIS. Phase, V - Condirct three test periods of the seismic system over a period of six mimilis. Detailed reports covering the wurk. done in Phases I, 11, and IV have been i : . r tr I - i t report will, therefore, cuni.entrate on the work perfurmed in Phases III anti V.]

Jan 1, 1975

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957

By Reinhardt Thiessen

Views and conceptions of the origin, composition, and general nature of coal differ so widely that to determine the real extent of actual knowledge is no easy matter. The chemist finds difficulty in attacking the chemical problems and the engineer lacks a broad chemical basis for the study of his problems. Thus the economical and efficient utilization of coal in the industries suffers from a lack of knowledge of the composition of coal itself. Most scientists interested in this matter, as has been brought out in discussions during the recent investigation of coal problems, appear to have only a vague idea of the components of coal and their origin. Some are even in doubt as to whether substances derived from the wood and resins of plants form a part of coal; and few seem to have more than the dimmest idea of what are the components of coal, the condition in which these now exist, and the transformations that they haye undergone. Although during the paiilt century or more many co.rrect observations have been made and recorded, these were falsely or inadequately interpreted, so that many of the interpretations rendered are contradictory. As a result there has been great confusion. Many of the observations made in the past, although accurate and correct, could not be explained, because the principles involved in a correct solution of the problem were not then known. For example, Parkinson, Hutton, Petzhold, Guembel, and others made valuable discoveries regarding the processes by which plant substances are transformed into coal, but as the principles involved are those of colloidal chemistry, a science not known to the scientific world of that time, the observed facts could not be interpreted and the solution of the whole problem was blocked. The explanation of the true meaning of the alternating bright and dull bands so familiar in all ordinary bituminous coals afforCls another example. This banding has been observed and recorded from the earliest times, and has led to the forming of many false theories. Some gAologists, for example, have endeavored to explain the bands as due to alternating climatic conditions during the coal-forming period. Had the geologists known the true nature of coal they could not have made this mistake nor many others made in the past. To fill in a few of these gaps and to clarify some of the existing confusion is the aim of this paper. The immediate cause that led the author to investigate further the composition of coal and the origin and structure of its constituents was that when an attempt was made to discover the meaning of the coking and noncoking properties of coal a more exact knowledge of the nature of coal was required than was then available.

Jan 1, 1920

By Kenneth Wardell

Criteria have been fully developed for determining the optimum size of oil and gas well blocks. The criteria lead to the formation of well barrier pillars which are, of themselves, inherently stable and take account of variable mine roof and floor conditions. The criteria ensure, through considerations of ground movement, that strains transmitted to well casings, are within tolerable limits of casing specifications. The criteria cater for well barrier pillars in multi-seam mining situations and where previous old mining has taken place. The criteria maintain flexibility in being adaptable to local mine design situations. The criteria are applicable to proposed extraction thicknesses up to 15 feet at depths up to 2,400 feet. The criteria are related to producing wells and to abandoned wells. In the latter connection, various states of well abandonment are recognised.

Jan 1, 1980

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By Ellis S. Hertzog

The data published in this report cover only one phase of a special study of the physical and chemical properties of Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, end ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This paper makes available for the first tine fairly comprehensive information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors have included a complete description of it in this report.

Jan 1, 1938

By Corate L. Brierley

Low-grade porphyry copper ores containing chalcopyrite as the primary mineral was leached by two strains of acidophilic, thermophilic microbes belonging to the genus Sulfolobus. Leach tests were conducted in glass columns heated to 60-70° C. Pinto Valley and San Manuel ores sized to -1/2 inch + 50 mesh were effectively leached by the thermophilic organisms, but pinto Valley and Cyprus Bagdad ores sized to -2 inch + 1/2 inch resisted leaching. Aeration did not contribute measurably to bacterial copper extraction, since two columns, one inoculated and one sterilized, having a rest/ leach cycle without recurrent aeration exhibited copper extraction patterns similar to those of the aerated columns. Distilled water can be substituted for 9K medium without diminishing copper extraction. Decreasing the pH of the leachate to about 1.8 enhanced the extraction of copper from pinto Valley ore with the thermophilic microbes. Thiobacillus ferrooxidans was found to be relatively ineffective at copper extraction from pinto Valley ore. Of eleven solvent extraction reagents tested, Adogen 364 and Warsol at concentrations of 0.1% and 0.012 were inhibitory to oxygen uptake by the two Sulfolobus strains. Di-2-ethyhexyl phosphoric acid at concentrations of 0.1%, 0.01% and 0.001% were totally inhibitory to the respiration of both organisms.

Jan 1, 1979

By Lowell B. Moon

The Stange and Byrnes Heirs manganese mines, adjoining properties in Bland and Giles Counties, Va., have produced at least 20,000 long tons of concentrates containing 8,000 long tons of manganese. They were selected as the site for a strategic-mineral development project because of the existence of geologic possibilities for extensions of the known ore body. In plan, the long dimension of the ore body parallels the axis of a major anticline. Localization apparently is due to longitudinal and transverse fracturing incident to two-way folding. That the manganese oxides were deposited by downward-moving solutions is suggested by the fact that mineable concentrations are confined to a coarse, porous sandstone under-lain by impervious silt and clay. Bureau of Mines project work began on January 15, 1941, and was completed on April 23. The work sampling the faces of the pit, bulldozer trenching, and churn drilling. Pit sampling consisted of 132 channel samples usually 5 feet long and taken at 20-foot intervals. Seventeen trenches aggregating some 4,500 feet in length were dug by the bulldozer. Trenches averaged 12.6 feet in width and 5 feet in depth. A total of 1,978 feet of churn drilling was done in 33 holes. In preparation for churn drilling it was necessary to construct roads to 21 of the 33 sites. A total of 2,867 linear feet of road averaging 13 feet in width was built.

Jan 1, 1950

To develop more accurate means of measuring low ventilating air velocities in underground mines to facilitate compliance with ventilation standards. The Approach: A commercially available vane anemometer which produces an electrical, rather than a mechanical, output was coupled to electronic circuitry to produce the Bureau's Digital Low Velocity Anemometer (see photo). [ ] How It Works: The experimental instrument has a vane anemometer head which produces an electrical output signal with a frequency directly proportional to the rotating speed of the vane anemometer shaft. The commercially available ABBIRKO FLOWMASTER anemometer head was used in this instrument. In the signal conditioning circuits the electrical signal from the anemometer is converted into pulses, which are counted during either 3-second or 1-minute intervals, depending on the position of the operator's control switch. (Readout is either "instantaneous" or averaged for a period of one minute.) The number of pulses counted is then translated (integrated and divided by a constant) in the logic circuits to get average speed. Average air velocity in feet per minute is displayed in illuminated digits. (See simplified diagram of circuitry.)

Jan 1, 1975

By Beatrice Lukens, David Schlain, John D. Prater

"The electrolytic manganese process4/ developed by the Bureau of Mines involves the electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell. Metallic manganese is deposited on the cathodes, and sulfuric acid is produced at the anodes. The spent electrolyte contains, in addition to the sulfuric acid, approximately 40 percent of the manganese sulfate and most of the ammonium sulfate originally present in the feed solution. This spent solution is used to leach fresh ore that has previously been subjected to a reducing roast. The resulting leach liquor is purified and returned to the cell.Manganese of very high purity is produced by the electrolytic process. The properties of this metal are so different from those of the best grade of manganese that can be made by any other commercially feasible process that it is virtually a new material. Electrolytic manganese has been used in the preparation of new high-manganese alloys with valuable properties.3/ and further developments are to be expected. The electrolytic manganese process not only results in a product of superior qualities, but is applicable to large tonnages of domestic ores that are unsuitable for direct use in producing ferromanganese.The future industrial use of electrolytic manganese is of course, related to its cost. Decreases in the cost of production will lead to wider use of the metal; conversely, increases in the volume of production made possible by greater demand will bring further .decreases in cost."

May 1, 1946

By Robert H. Ridgway

Chromite has been produced commercially for slightly more than a century. Developed, at one time, chiefly as a chemical pigment raw material, it has subsequently found extensive application in other chemical industries - as a refractory material for furnace linings and as the sole source of the metal chromium. For some years prior to 1914, its use as a refractory predominated; but post-war development in alloy steels, principally stainless steels, enhanced the metallurgical demand in the form of ferrochrome with a consequent increase in the demand for chromite. More recently direct reduction of chromite in alloy-steel manufacture has been applied to a limited extent. Alloy steels containing varying amounts of chromium, with or without other alloying elements, now find extensive use in a ride variety of ways - in structural material, machines, industrial equipment transportation by land, sea, and air, sanitary equipment, food preservation, and a multitude of other uses. In recent years chromium plating has had wide application and has become important. industrially, but the amount of raw material consumed

Jan 1, 1936

By Peter P. Kopas

Study, analysis, fabrication and testing for canopies on Roof Bolters and Shuttle Cars in coal seams under 48?.

Jan 1, 1980

By Harold J. Bennett

This study was performed by the Bureau of Mines to evaluate the potential supply of primary copper from domestic resources. A tonnage-price relationship was developed indicating the quantity of copper that could be produced economically from known deposits at various copper prices and at various rates of return on the required capital investment. Costs of production are based on estimated capital and operating costs for mining, concentrating, smelting, and refining the copper. Total known recoverable copper resources are 189 million short tons of which 83 million tons could be economically recovered assuming a price of $0.50 per pound of copper, credit for the recovery of byproducts, and a 12-percent rate of return on capital investment. The quantities of recoverable byproducts associated with the 83 million tons of recoverable copper are molybdenum, 1.8 million tons, gold, 43 million troy ounces, and silver, 740 million troy ounces.

Jan 1, 1973

By R. V. Ramani

This report is volume 2 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Geology and Reserves subsystem of the Master Design Simulator. The two functions of this subsystem are: 1) the design of a geological data library to provide input to the other subsystems of the simulator; and 2) the calculation of coal reserves and associated values and grades under various user-specified conditions. The subsystem uses a weighted moving average method to interpolate between the borehole values, and provides output in report format, graphical plots and/or storage on magnetic tape or other storage devices for later retrieval. The application of the subsystem as an independent model with test results and comparisons with other methods of computing reserves is also presented. The appendix comprises a users manual for the model, and includes a program listing.

Jan 1, 1974

By Eugene W. Bartel

This report describes in detail the circuitry used in the Automated Time Domain Reflectometry System and the testing and modification done to the system to improve the units performance and consistency. The analog ATDR software is described and explained in detail. Also attempts to implement the same Assembly Language program in a higher level language (PLM) are documented along `h two versions of the PLM program - one which uses a data filtering approach to limit noise and another which uses data averaging to reduce noise. The field testing of the analog and digital ATDR units is described along with the hardware modifications that resulted. The analog unit has been abandoned and the digital unit adopted for most field tests. Tests indicate that the digital units are much more consistent and less confusing for the lay-person to operate. The results indicate that the it can locate an abnormality in a test cable to within 5% of the true location (provided the cable phase velocity is known). The units can consistently locate shunt type faults which are less than 300 ohms and series type faults which are greater than 30 ohms.

Jan 1, 1980

The U.S. Bureau of Mines conducted a laboratory study to determine what effect use of water-jet-assisted cutting has on frictional-ignition suppression. A single bit with a steel tip, installed on a rotating drum, repeatedly made 22-in-long cuts in a block of Berea sandstone. The drum was operated in an enclosure that contained an explosive methane-air mixture. High-pressure front-mounted water jets operating at 2,000 to 5,000 psig and low-pressure rear-mounted sprays operating at 80 psig were used; the number of ignitions that occurred with each type of spray was compared. The rear-mounted spray was more effective for preventing frictional ignitions than the front-mounted water jet.

Jan 1, 1989

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1986 was $405.2 million, a slight decrease from that of 1985. Alabama was second in the Nation in production of bauxite, crushed marble, and ferroalloys; third b fire clay; fifth in masonry cement and lime; sixth in total clays; and seventh in recovered sulfur. Alabama ranked 19th nationally in value of nonfuel minerals produced. Cement, clays, lime, sand and gravel, and stone were the major commodities produced.

Jan 1, 1988

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936, and their rapid development have brought the problem of brine disposal to the foreground in that State. The ultimate magnitude of the problem is not yet known, but already it is treat enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field b brines in Illinois rend has studied in detail three subsurface disposal systems.]

Jan 1, 1940

By John C. Machisak

The Nation's mining and quarrying industries have again met the annual challenge to their ingenuity--that of reducing disabling work injuries among their employees. The effectiveness of management in facing this problem and in meeting this responsibility from the results of the 1961 National Safety Competition. Three hundred ninety-three or 45.3 percent of the mines and quarries participating in the competition established a new record number of participants operating throughout the competition year without a disabling work injury. Another record established in the 1961 contest was the number of participants (868) enrolled in the competition. This annual safety competition was begun in 1925 and is conducted by the Bureau of Mines, U.S. Department of the Interior. It provides for six bronze Sentinels of safety trophies which are awarded each year to the winning participant in each group. Since its inception, the competition has exerted a strong influence in the field of safety promotion. The statistical record of its accomplishments over the years gives strong support to the theory that well-organized and well-administered safety programs are effective tools to be used to reduce the number of disabling work injuries. It stimulates and holds the interest of employees and management in accident prevention. Because of this, mines and quarries participating in the contest have a more favorable safety record than those operations not enrolled.

Jan 1, 1963