Search Documents

By Z. D. Hora

Sand and gravel resources of the southern coastal region of British Columbia may be linked to various episodes of Wisconsin glaciation. During Wisconsin and probably earlier times, the Fraser Lowland and coastal areas were subjected to repeated glaciations separated by non-glacial intervals. Each major glaciation was accompanied by isostatic and eustatic changes in sea level up to 200 m or more. As a result, the Lowland was covered by the sea during much of Quaternary time. Because the Fraser Lowland is surrounded on two sides by high mountain ranges, glaciers terminated in the sea during their maximum advance. Therefore, meltwaters released during deglaciation, together wit h retreating glacier ice, could produce widespread and extensive sand and gravel deposits both along the coast and throughout the Fraser Lowland and adjacent areas.

Jan 1, 1984

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By John Stoten

"The 1980s have proven extremely difficult years for many resource-based organizations. Mining companies have learned how to weather the negative effects of inevitable economic cycles. However, with some notable exceptions, such as gold mining companies, the mining industry has faced a broader and deeper round of cutbacks than any experienced since the 1930s. Downsizing has been a major issue for many mining companies as they have faced the need for dramatic staffing cost reductions in the recent past.The continuing current rapid rate of change in technology and the marketplace, coupled with increasing merger and acquisition activity, will provide an on-going need for some companies to face major reorganization. This inevitably will involve down-sizing activity in some instances.Given this scenario, it is worth reviewing the industry's past experiences to identify approaches and techniques that could prove of value in handling a future staff downsizing challenge. This paper is based upon a downsizing consultant's experiences with the mining industry and other sectors, and highlights what appear to be key staff reduction planning and process issues.Planning for DownsizingA review of companies' downsizing activities of the last few years reveals four key activity stages which need to be addressed to ensure a successful transition. These stages are:1. organization planning;2. developing cost reduction strategies;3. implementing downsizing; and4. building for the future.A business situation that is severe enough to require drastic staff cuts typically affects all aspects of a company's operations. Most mining companies have reviewed cost efficiencies in many operational areas. However, these reviews often have been short term in focus . As a result, some companies have experienced multiple downsizing; each event a response to an immediate economic threat. This has sometimes resulted in an unstable organizational environment, with severe stresses on staff morale and productivity.In the long term it is more efficient and less stressful to the organization to adopt a more comprehensive and longer-term strategy. Especially in capital intensive mining operations, it makes sense to review all areas of business activity, not just staffing."

Jan 1, 1989

By C. O. Stee

IN the October, 1936, issue of the Canadian Mining Journal there was published a series of very comprehensive and exccellently illustrated papers by Mr. C. O. Stee and members of his staff dealing with Siscoe operations and ore-bodies. These were, in the order in which they appeared: Geology of Siscoe Gold Mine, by O. L. BACKMAN Diesel Power at Siscoe Gold Mines, Ltd., by C. O. STEE andE. A. BLOMQUIST Mining at Siscoe, by L. T. POSTLE and W. F. Engineering and Surveying, Siscoe Milling Practice, Research and Testing Laboratory, Assaying of Mill Tails and Solutions, BROWN(6) by P. A. TEEPLE (7) by L. E. DJINGHEUZTAN by L. RIVETT (8) by G. IRWIN (9) The Editor of the Canadian Mining Journal cordially assented to our suggestion that these papers be reviewed at the 1937 Annual General Meeting of the Institute, and the authors very kindly accepted our invitation to present such reviews . Of these courtesies, full acknowledgment is here accorded. To our readers, we commend the original papers in the Canadian Mining Journal. The summaries presented at the meeting follow. EDITOR. THE GEOGLY OF THE SISCOE MINE The Siscoe gold deposits lie in and near a stock of granodiorite, related to the Bourlamaque batholith, which has intruded highly folded Keewatin volcanic rocks .. The volcanic rocks lie to the north of a belt of Timiskaming sediments.

Jan 1, 1937

By M. A. Creaney

"The Construction Group is responsible for the construction of all of Placer Dome’s major projects and contributes to the development of most major feasibility studies. This group includes an international collection of Placer Dome people who have built mines in Papua New Guinea, Australia, Chile, the United States and Canada. This paper outlines the changing role of the Construction Group from the early days of single projects to today, when several projects are in various phases from feasibility to construction. The projects’ total annual budgets have from time to time exceeded one billion dollars. IntroductionAs the competition increases globally between the major gold mining companies, the impetus continues to build mines at the lowest cost with the shortest construction schedule. Placer Dome has more than met that challenge by building mines around the world at a pace that was not contemplated 15 or 20 years ago. Since 1960, Placer Dome has built 30 mines and expansions at a cost of nearly 4.5 billion dollars.In the last six years alone, Placer Dome has built 14 mines and expansions, worth 2.6 billion dollars. The company’s success is due primarily to Experience, Innovation, People and Standards.The diversity between projects, let alone the pace, has been a challenge. Placer Dome has built mines around the world in a variety of extreme climates and distinctive cultures. The construction experience gained from these projects has allowed Placer Dome to develop an extensive knowledge and data base making it easier to “fast track” projects.Through the years Placer Dome has developed a human resource base. It now has an experienced and adaptable core team of people able to set up construction projects and build mines anywhere in the world. By developing standards and systems to support the projects they can act as soon as a new project is approved, and complete the projects quickly and effectively. The result is that Placer Dome now has the construction expertise to build its own mines, giving them the competitive advantage that allows them to design and construct a mine in the least time at the lowest capital cost. This was demonstrated in March 1997 with the completion of the construction of two new mines in 12 months."

Jan 1, 1998

By G. H. Montgomery

THE PROPERTY of Aunor Gold Mines, Limited, consists of eleven claims, located in Deloro township, approximately three miles southeast of the town of Timmins. Production began in 1940 and currently the mine is operating at a rate of 485 tons per day. GEOLOGY AND MINE DEVELOPMENT The ore zone at Aunor occurs in altered lavas bounded on either side by soft talc-chlorite schist, locally known as 'soapstone'. The zone has a strike of N.80°E, dips 60° North, and varies in width from 0 to 250 feet. Within this zone the main orebody has a westerly plunge, away from the No. 1 shaft area (Figure 1). The mine is developed by a vertical three-compartment shaft from surface to the 3,082-foot horizon. Working levels are spaced at 125- foot intervals from the 625-foot to the 1,625-foot horizon, from which to tl1e 2,125-foot level the interval is 250 feet.

Jan 1, 1957

By C Carbonneau

In order to successfully produce columbium pyrochlore concentrates, St. Lawrence Columbium and Metals Corporation had to face two principal problems met in several new operations but possibly made more acute than usual owing to the newness of the project. 1.-The ore is particularly complex, as it is made up of an elaborate intermingling of carbonates and discontinuous ultra-alkaline rock bodies of various ages and types in which no less than seventy mineral have been re-ported. Obvious petrographic or structural controls are lacking. Ore boundaries have to be defined on the basis of assay results and the determination of several minerals which occur in trace amounts. 2.-The pyrochlore concentrates produced had to com-ply with a set of stringent specifications. This fact, combined with the low Cb205 content of the ore, necessitated the use of a beneficiation process that would have to operate at a concentration ratio greater than 100:1. A brief description of the mill circuit is given. Mill stability was obtained through extensive mineralogical study of the mill feed coupled with close geological and engineering control of the mining operations.

Jan 1, 1965

By Wayne N. McKee, Scott A. Lewis

"Introduction to the Syncrude OperationSyncrude Canada Ltd., located 42 km north of the city of Fort McMurray, Alberta, (Fig. I) is an integrated operation that has produced synthetic crude oil from the Athabasca oil sand deposit since 1978.The operation, consisting of a surface mine, an extraction plant, a bitumen upgrader, and a utilities plant, is currently capable of producing over 60 million barrels of crude oil per year. Production is expected to increase to 70 million barrels of crude oil per year over the next five-year period with no major changes to equipment or process planned.The Syncrude surface mine, producing a total of 675 000 tonnes of ore and waste per day, rates as one of the largest mines in the world. A strip mining method is utilized, with two or three operating benches necessary to excavate a total depth varying between 60 m and 70 m. The 20 m to 30 m of overburden is removed by electric and hydraulic shovels and 200-ton haul trucks, and dumped in the mined-out pit for final storage. The overburden operation creates a flat bench near the top of the ore zone on which the four 60 m3 draglines operate. The draglines excavate interbanded ore and waste in the highwall, with ore placed on the operating bench in windrows, and waste returned to the mined-out pit. The windrowed ore is reclaimed by four bucketwheel reclaimers, and discharged onto a conveyor system for transfer to the extraction plant."

Jan 1, 1993

By J. A. Abols, P. M. Grady

Recovery via gravity is one of the oldest mineral processing methods available. Unfortunately, the use of gravity techniques for gold recovery has been in decline for the past century as more effective chemical processes such as flotation and leach/CIP have been developed. Recently, with the push towards more sustainable environmental outcomes, the benefits of gravity separation have become more apparent. While gravity as a unit process is not usually capable of achieving as high a recovery as flotation or whole ore cyanidation, a combination of gravity devices alone or in conjunction with these processes can offer significant advantages to the operator. This paper reviews the range of gravity devices available, their application and the results that can be achieved by maximizing gravity through the use of a combination of gravity recovery devices. Three case studies are provided.

Jan 1, 2005

By Elma van der Lingen

Gold is considered the most inert of all metallic elements, but the metal can show catalytic activity when prepared by specific techniques. Preparation techniques being used to prepare gold catalysts systems mainly involve precipitation methods incorporating gold compounds or complexes. This paper introduces a totally different method for the preparation of gold-based heterogeneous catalysts that can be used for oxidation and reduction reactions, as well as electrocatalysts. The method involves alloying of gold with a less noble metal, such as aluminium, to form a gold-containing intermetallic precursor. AuAl2 was produced by melting gold and aluminium together in a vacuum arc furnace under a protective atmosphere. The aluminium is then dissolved from the AuAl2 precursor by means of NaOH to produce a highly porous gold structure. The paper also reports on a method of incorporating transition metal oxide(s) with the porous gold to form an active heterogeneous catalyst. Promoter elements can also be melted with AuAl2 to improve catalytic activity. Alloying has the advantage that the promoter element can be in contact on atomic level with the gold. In-situ xray photoelectron spectroscopy (XPS) studies have also been done on the porous gold catalysts to further clarify the CO oxidation mechanism on gold-based catalysts.

Oct 1, 2003

By w. w. Fraser

"In late 1985, Hudson Bay Mining and Smelting Co., Limited announced the Namew Mine/Mill project. Environmental baseline monitoring and planning began in early 1985 while a major drilling program was under way to delineate the ore deposit. This paper overviews the environmental assessment work conducted for the mine/mill operation, and outlines the tailings and water management practices.Planned environmental works and approach were affected in late 1988 when a massive water problem was encountered in the mine. The requirement to depressurize the rock surrounding the underground workings led to the need to develop, on short notice, an environmentally-acceptable procedure to dispose of a large volume of slightly-saline water.Biological toxicity tests performed on the depressurized effluent proved the effluent to be non-toxic and thus allowed resolution of the disposal problem. This resolution includes the conversion of a large water body from native fish species to a rainbow trout fishery."

Jan 1, 1991

By Julien Rivard

Au printemps 2011, la Corporation minière Osisko met en production le gisement Canadian Malartic, qui devient la plus importante mine d?or à ciel ouvert au Canada. Pour lui faire place, elle a déménagé un quartier de 205 maisons et construit 6 nouveaux bâtiments institutionnels. Les démarches ont commencé en 2006. La compagnie a d?abord établi l?emplacement du nouveau quartier résidentiel, en collaboration avec la Ville de Malartic, puis fait la conception de ce quartier de manière à refléter au mieux les caractéristiques du quartier à déménager. Elle a ensuite effectué une opération d?assignation consistant à proposer à chaque propriétaire intéressé un lot dans le nouveau quartier. Au total, 140 résidences ont été déménagées en 2008 et 2009 et 65 été rachetées par la compagnie, le tout par des ententes de gré à gré sauf pour un seul cas. La réussite d?une opération d?une telle importance sociale n?a été possible que parce que la compagnie s?est assurée d?un soutien massif de la population et des autorités pendant tout le processus. Cette expérience peut être fort utile pour les nombreux projets miniers dont l?insertion dans la communauté est un enjeu important.

May 1, 2011

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By M. O. Pekguleryuz, D. S. Aydin

The high temperature oxidation and ignition resistance of Mg-(0-6) wt% Nd alloys have been investigated via isothermal and continuous heating experiments conducted in air atmosphere. Alloy composition is observed to be effective in low levels (~ 0.5 %) in the ignition temperature (Ti) of the alloys; the Ti of pure Mg increased from 630 °C to 770 °C with 0.5 wt% Nd addition. However, no noteworthy improvement was achieved with further additions up to 6 wt% Nd. The initial microstructure was observed to determine the oxide structure on the surface due to the differing oxidation behavior of the phases (a-Mg + Mg12Nd intermetallics). It has been found that the formation of a Nd-depleted region at the subsurface due to extensive Nd oxidation at the oxide/intermetallic interface lowers the protective ability of the oxide scale.

Jan 1, 2015

By Rick J. Chalaturnyk

In Alberta, oil sands bitumen is utilized for synthetic crude oil production by surface mining, bitumen extraction followed by primary (coking) and secondary (catalytic hydrotreating) upgrading processes, or by catalytic hydrocracking and hydrotreating replacing the primary and secondary upgrading processes. Oil sands tailings, composed of water, sands, silt, clay and residual bitumen, is produced as a byproduct of the bitumen extraction process. Several processes have been proposed for the treatment of oil sands tailings, resulting in different recovered water characteristics, consolidation rates and consolidated solid characteristics, which may have effects on the performance of the overall plant operations. A process for the same purpose has been developed by treating the oil sands tailings with CaO lime and CO2 and thickening it using a suitable thickener. In this process a release water of acceptable properties is recovered in a short retention time, which makes it possible to recycle the recovered water, probably after a reconditioning treatment, as warm as possible to improve the thermal efficiency of the extraction process. The paper presents the theory and laboratory results for the CaO and CO2 thickening of low temperature flotation tailings. The water release rates, segregation potential of the thickened underflow and chemistry of the release water are shown and discussed. It is suggested that in using the proposed process, the thickened tailings underflow can be disposed for further consolidation, or combined with the coarse tailings to produce Blended Composite Tailings, corresponding to the Composite Tailings process in the existing hot water extraction plants.

May 1, 2002

By X. Cao, J. J. Jonas, Wanjara. P., J. Gholipour, E. Dalgaard

The linear friction welding (LFW) behaviour of near-ß titanium alloy Ti-5Al-5V-5Mo-3Cr (Ti- 5553) was investigated. Microhardness measurements were performed in order to evaluate the mechanical properties of the welded material. The linear friction welded (LFWed) Ti-5553 was examined with optical microscopy and scanning electron microscopy (SEM) to evaluate the microstructure’s response to the thermomechanical conditions. Characterization of the welds included analysis of the microstructural features of the weld region and thermomechanically affected zone (TMAZ) in relation to the parent material.

Jan 1, 2010

By Harry R. Oldale

This paper first covers the general and economic geology of the Coxheath Hills area, and then outlines the exploration and mining development that has been carried out since the first discovery of copper in the area in 1875. The work of Mariner Mines Limited from 1963 to the present time is detailed, particular attention being paid to the recent discoveries of copper, silver and lead mineralization that have greatly enhanced the potential of the area.

Jan 1, 1967

By C. J. Newman, K. Molnar, A. G. Storey, G. Macfarlane

"The Kidd Creek copper smelter started operation in June 1981 using the Mitsubishi Continuous Smelting Process. A steady increase in plant production rates has been demonstrated, and the annual tonnage of concentrate smelted is now double the original design rate. This paper summarizes recent modifications made to increase concentrate feed rates, increase on-line time, reduce copper losses and control the impurity level in anode copper. It includes improvements made to furnace design, improvements to reduce downtime f or boiler cleaning, and improvements made to the acid plant to allow handling of increased gas flowrates and higher gas strengths while maintaining low acid plant emission rates. IntroductionThe Kidd Creek Division of Fal conbridge Limited operates a base-metal mining and metallurgical complex, located in Timmins, Ontario, which includes an underground mine, a 13 500 tonne/day concentrator, a 130000 tonne/year zinc plant and a copper smelter and refinery, The copper smelter and refinery were commissioned in 1981, with an installed capacity of 59 000 tonnes/ year of cathode. The smelter, utilizing the continuous smelting technology of the Mitsubishi Process, has subsequently been expanded in production capacity, and in 1991 produced 113 500 tonnes of blister copper The capacity of the refinery, which uses Onahama No. 3 tankhouse technology, has been increased to 96 000 tonnes/year of cathode. The capacity increase at the smelter has been realized through the input of additional oxygen to both the smelting and converting furnaces, without increasing the process off-gas flowrate through the associated waste heat boilers.In this paper, a brief review of smelter operation and modifications in the period 1982 to 1987 is presented, together with a more detailed discussion of operation during 1988 to 1991, and a discussion of future planned improvements."

Jan 1, 1992

By G. J. Kipouros, W. Judge

"The prevalent metal extraction processes for most reactive metals are fused salt electrolysis and metallothermic reduction. The feed material for both of these processes is the anhydrous chloride of the metal under consideration. Dehydration of the feed material is then a critical step in the production of most reactive metals and requires rigorous thermodynamic analysis. Thermodynamic data for most of the reactive metal chloride hydrates have not been measured. Improper dehydration of the metal chloride may lead to a prohibitive amount of hydroxychloride, oxychloride, and oxide. To prevent hydrolysis a certain pressure of hydrogen chloride is required. An estimation and prediction model is presented for the vapour pressures of reactive metal chloride hydrates in an attempt to deduce the conditions necessary for dehydration to proceed without hydrolysis. Thermodynamic data including heat capacities, standard entropies, and standard enthalpies are estimated/predicted for all conceivable intermediate hydrate compounds. Estimations are based on published data as well as trends proven in similar systems. The thermodynamic estimations and predictions are presented for the magnesium, neodymium, praseodymium, and dysprosium chloride hydrates. INTRODUCTIONThe high reactivity of metals such as the alkalis, alkaline earths, and lanthanides prevents their reduction by traditional pyro- or hydrometallurgy. In their elemental form, these metals are raw materials in the manufacture of intermediate products such as alloys and electronic components. Currently the only two viable metal production methods are fused salt electrolysis and metallothermic reduction. Various feed materials have been proposed for these processes. Using the chloride of the metal as a feed material offers advantages in separation and purity of the final product, as well as lower energy input. Chlorides, however, are hygroscopic and must be dehydrated before use. Improper dehydration will lead to a prohibitive amount of oxychloride which will lower efficiencies and contaminate the final product.Optimum conditions for proper dehydration of MgCl2•6H2O to produce pure MgCl2 without hydrolysis have been calculated from existent thermodynamic data and have been reported previously (Kipouros, 1987; 2001). Calculations were also performed for the case of production of pure anhydrous NdCl3 from NdCl3•6H2O (Roy, 1997)] and the mechanism of dehydration was elucidated. Some thermodynamic studies on the dehydration of chlorides of the rare earths have also been conducted (Sundstrom, 1997; Hong, 1997; Aschcroft, 1968; Haeseler, 1965; Ukraintseya, 1989)."

Jan 1, 2012

By Yongjun Peng, Yufan Mu, Rolf A. Lauten

"Chalcopyrite, a major source of copper, is commonly found associated with iron sulfides, particularly pyrite. The separation of chalcopyrite and pyrite by flotation is difficult due to the galvanic interactions between pyrite and chalcopyrite during grinding and flotation. Galvanic interactions may cause oxidation and dissolution of chalcopyrite, copper activation of pyrite and the formation of hydrophilic iron hydroxide coating. The overall effect may change the floatability of the components and lead to the misplacement of pyrite into chalcopyrite concentrate. The objective of this study was to investigate the effect of lignosulfonate-based biopolymers on the depression of pyrite in the flotation of chalcopyrite with xanthate as collector and the mechanism responsible for the selective depression of pyrite. The flotation results showed that biopolymers depressed the flotation of both copper-activated pyrite and chalcopyrite in single mineral flotation although to different extents. In the flotation of mixed mineral systems, biopolymers significantly depressed pyrite flotation but had a less influence on chalcopyrite flotation. The selective depression of pyrite by biopolymers was due to the preferential adsorption of biopolymers on copper-activated pyrite surface. Galvanic interactions between pyrite and chalcopyrite surfaces promoted copper activation on pyrite. Presence of cuprous ions on pyrite surface favored biopolymer adsorption by the formation of a complex between the cuprous ions and biopolymer molecules. The same galvanic interactions also facilitated chalcopyrite oxidation leading to the formation of hydrophobic polysulfide that enhanced the hydrophobicity on chalcopyrite surface. The biopolymer structure controlled the depression effect. The results showed that the biodegradable biopolymers are promising depressants for pyrite.INTRODUCTIONCopper sulfide minerals, such as chalcopyrite (CuFeS2), bornite (Cu5FeS4), chalcocite (Cu2S) and covellite (CuS), are the major mineral source for copper. They are often found finely interlocked with iron sulfides, especially pyrite (FeS2) (Owusu, Brito e Abreu, Skinner, Addai-Mensah, & Zanin, 2014). Pyrite, as the most abundant sulfide mineral, is perceived as gangue in most cases and should be removed from the associated sulfides to minimize its contamination of the copper concentrate (Owusu, Addai-Mensah, Fornasiero, & Zanin, 2013; Wang & Forssberg, 1991). The commonly used strategy to remove pyrite is flotation (Wang & Forssberg, 1991)."

Jan 1, 2016