Search Documents

A novel approach to validate size distributions obtained from bubble sizing techniques is introduced. The experimental rationale consists in verifying whether the output features the anticipated bi-modality when two uni-modal populations (ca. 0.5 and 5 mm) are mixed in a bubble column. The degree of deviation is quantified by comparing the calculated and real proportions on a volumetric basis. A sampling-followed-by-imaging technique was used to proof the concept. The results showed the anticipated bi-modality in which the real and calculated proportions corresponded with a deviation of less than 15 per cent, considered good given the severity of the test. However, the deviation was correlated to the superficial gas velocity (Jg) in the column and was consistently against smaller bubbles. Possible sources of bias are suggested.

Jan 1, 2005

By E Villaescusa, C Drover

The stability of access tunnels is one of the main engineering challenges in deep underground mine construction. Many underground hard rock mining operations are now reaching depths where the induced stresses are such that sudden and violent failure of the excavations can occur very soon after construction. The loading conditions on the installed ground support schemes are often underestimated by conventional engineering design methods. Therefore, the actual loading conditions often exceed the installed ground support capacity. This can result in failure of the excavations and, in extreme cases, potentially closure of mining operations amounting to hundreds of millions of dollars in lost production. More frequently, violent excavation instability at great depth causes operational delays, costly and unplanned rehabilitation, as well as risks to worker safety. In order to address this challenge, this paper briefly summarises a modern, innovative approach to the design and construction of mine development at great depth. The process follows seven main steps. The first step is to characterise the rock mass strength, structure and stress. The second step is a stability assessment, which identifies the plausible modes of excavation failure, based on the rock mass characterisation. The third step is the definition of an excavation geometry which is harmonic to the high stress conditions. The fourth step is to prepare a site-specific face destressing drill and blast design which will reduce the potential for rock mass instability during the development construction cycle. The fifth step is to accurately quantify the expected loading conditions on the installed ground support. The method of doing so is uniquely analytical and probabilistic. It is based on the natural mechanical relationships between rock strength, structure, induced stress and the physical characteristics of the instability, including its mass and ejection velocity. The sixth step of the design process is to specify a ground support scheme arrangement with sufficient strength and displacement capacity to exceed the rock mass demand by a safe margin. The final stage is to install the complete ground support scheme using mechanised technologies which minimise the exposure of the equipment operators to unsupported ground at the tunnel face.

Nov 29, 2022

By S Larbi-Bram, F Shi, E Manlapig

Mining companies have recognised that characterisation of particle breakage plays an essential role in the design and optimisation of comminution circuits. Recently the JKMRC comminution research team has developed a new breakage model incorporating the effect of particle size, and a new breakage characterisation testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions. The latter is believed to be the dominant breakage mechanism in AG/SAG mills. Existing devices, such as the JKMRC Drop Weight Tester, are not suitable for performing repetitive impacts since they are too time consuming. Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalised experimental test program on professionally designed and manufactured JKRBT machines. The first JKRBT was installed at the Anglo Research laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the project in 2008, with commercial release expected in early 2009. The JKRBT has the potential to revolutionise ore testing, with applications in laboratory impact breakage characterisation of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control of comminution circuits since it is readily adaptable to on-line ore hardness measurement. Can any mine afford to miss out on this technology?

Jan 1, 2008

By P K. Seccombe

The McKinnons gold deposit is hosted by weakly deformed, Palaeozoic metasedimentary rocks of the Cobar Basin in the western Lachlan Fold Belt of New South Wales. Mineralisation comprised a largely supergene resource of 1.7 Mt of ore, grading 1.7 g/t gold, established over structurally controlled, primary gold and base-metal mineralisation in underlying, carbonate-rich meta-siltstones and sandstones of Early Devonian age. Mineralisation was associated with at least two major fluid cycles. The first cycle was characterised by four stages of vein formation. Early quartz and carbonate veins (Stages 1 and 2) and quartz-pyrite breccias (Stage-3) occurred prior to, or early in, the main regional deformation (D1). Continued D1 deformation produced syntectonic, carbonate-base-metal veins (Stage-4), primarily in dilatant zones adjacent to fold axes. The second cycle of mineralisation was an epithermal-style event, driven by a shallow, syn-D2 or post-tectonic intrusion, defined by aeromagnetic imaging. The intrusion may have exploited a jog, controlled along the basin margin by basement faults. Mineralisation produced gold-pyrite veins, associated with pervasive quartz-sericite-adularia and chlorite-sericite alteration. Highest primary gold grades are confined to quartz-adularia boiling zones. The McKinnons deposit offers an important example of mineralisation formed by multiple processes. Early-stage, base-metal mineralisation at McKinnons reflects structurally focussed, basin dewatering and metamorphic processes, typical of other deposits in the Cobar Basin. By contrast, late-stage gold mineralisation at McKinnons is magmatically driven and of epithermal style. Recognition of overprinting distinctive geological events is critical, not only in modelling ore formation, but in developing a versatile exploration concept.

Jan 1, 1999

The major technological advances of the last 30 years have profoundly reshaped mining practices. Machines keep getting bigger while productivity continues to increase and manning levels drop. These trends will continue and the introduction of breakthrough technologies will continue to accelerate, driven by a continued focus on lowering the cost of production, improving the productivity of workers and machines, and ensuring safer working environments. At the same time, global consolidation of mining companies has impacted on technology development in a range of ways. There are many potential technologies being proposed, some already operating in Australian mines. The automation of underground load-haul-dump (LHD) trucks for example, continues the process of removing workers from the most dangerous operating environments. Global positioning systems fitted to draglines, fibre optic communication channels, and 400 tonne trucks are only some examples of what lies ahead. However, where we need to return focus is to the technology of management û which is also one of the two key interrelated themes of this keynote address. Have we, as an industry, adequately been able to keep up with technological advances? Are our management systems as competent as the machinery we employ? The other key theme is the processes of globalisation and consolidation. What are the impacts on our industry? What are the implications of these processes, particularly for the ways in which we manage our people? My paper is divided into several components:some comments on the coal industry and the dramatic restructuring we have seen in recent years; in the context of this restructuring, an overview of my company and its evolution; my views on the role of contractors; some comments on the consolidation also occurring in the mining machinery and equipment, technology and services sectors; some observations on two major areas of technology û drill and blast; and trucks, shovels and excavators; the implications of consolidation and new technology for our employees and management; and finally some comments on research programs.

Jan 1, 2001

By J T. Carswell

Best practice mine sampling should provide a detailed quantification of all potential sources of error at each stage of sampling, sample preparation and assaying.Quality assurance (QA) should include testing for and quantifying potential sampling errors, and should be the basis for establishing ongoing sampling protocols, should set error limits and define quality control (QC) procedures. QA should be within the framework of Theory of Sampling (TOS) but may not involve the estimation of the sampling constant and the application of Gy’s formula.Best practice QC should be carried out efficiently and in a timely and cost-effective manner with regular reporting against the guidelines established by QA.This paper provides an assessment of, and checklist for, current best practice sampling QA/QC with examples from operating gold mines including the QA/QC of underground (UG) reverse circulation (RC) grade control.CITATION:Carswell, J T, 2017. Best practice sampling QA/QC for gold and base metal mining – including how to assess the applicability of underground reverse circulation grade control sampling, in Proceedings Tenth International Mining Geology Conference 2017, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By D B, M A. Sares, D W. Coulter, D C. Peters

This presentation discusses NASA-funded research on the ability of hyperspectral remote sensing to map diagnostic acid rock drainage (ARD) mineralogy that adversely affects water quality within watershed and to determine the relative contributions of natural ARD sources of metals and acidity to that drainage. Ground-based reflectance spectroscopy, combined with water chemistry, is used to identify mineralogical and chemical variations throughout a watershed. Integrated with hyperspectral data acquired from airborne remote sensing platforms, such as the NASA Airborne Visible Infrared Imaging Spectrometer (AVIRIS) sensor, a methodology has been developed that should improve environmental assessments and tracking of impacts on and from drainages. Phase I of this project focuses on a drainage basin (Lake Creek), tributary to the upper Arkansas River in central Colorado, which is impacted by natural acid rock drainage from areas of high-sulfide hydrothermal alteration. This project builds upon research and inventory efforts by the Colorado Geological Survey (CGS) to identify hydrothermal alteration that is the primary source or is contributing to acidic and toxic drainage in Colorado. This presentation will cover ground and airborne hyperspectral remote sensing techniques and results and water analyses for seasonal high-flow and low-flow conditions in Lake Creek. Identifying correlations between mineralogy, especially mineralogy that can be identified through airborne remote sensing, and water chemistry is a key focus of this project. Of particular interest are low-pH iron phases such as jarosite, ferrihydrite, schwertmannite, copiapite, and transitional amorphous phases as well as AlOH phases from higher, although still acidic, pH environments which are observed to mix with the iron precipitates within the streams draining from the hydrothermal systems. Drainage in the Lake Creek watershed derives from the Grizzly Peak caldera (Oligocene), which exhibits extensive hydrothermal alteration. Alteration types include silicic, quartz-sericite, quartz-sericite-pyrite, advanced argillic, and argillic. By understanding the chemistry of a naturally impacted drainage and its relationship to the surrounding geology, the project goal is to allow more efficient and complete identification of such sources in mineralised terranes through remote sensing technology.

Jan 1, 2003

By M-A Van Ende, N Kumar, I-H Jung

In order to utilise the powerful thermodynamic databases for process simulations, a concept called Effective Equilibrium Reaction Zone (EERZ) was introduced to couple thermodynamic database calculations and reaction kinetics. Using the EERZ concept, many process simulation models for steelmaking processes have been developed within the FactSage steelmaking consortium. After validation of the simulation results by comparing with plant data, the simulation models have been applied to improve plant operations. Several success stories of the improvement of real steelmaking operations are shared. A new user-friendly FactProSim software developed for building process simulations is introduced.

Aug 21, 2024

By R A. Pax

Operational grinding mills emit significant acoustic emissions which are a consequence of the dynamic environment prevailing inside them. From a technical perspective, the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of primary comminution tumbling mills. To enable a logically coherent picture to be formed of the processes inside a mill, arrays of microphones have been used. This approach allows a clearer picture of the in-mill behaviour of the charge to be accessed. In contrast to single microphone approaches, usually located near the expected charge toe position, an array of microphones allows much more useful information to be obtained from grinding mill noise.This paper will discuss and present data obtained from microphone arrays positioned at the toe and shoulder locations of a mill, and how this information can then be used for the optimisation of grinding mills in real-time.CITATION:Pax, R A, 2012. Determining mill operational efficiencies using non-contact acoustic emissions from microphone arrays, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 119-126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By W R. Adamson

"Optimisation of drill and blast design and engineering can deliver a significant positive impact on the profitability of any mining operation; however, true engineering of the blasting process is less common than might be thought. The paper that follows explores this gap and suggests a process control-based approach to the challenge.The concept of applying modifications to drill and blast designs in order to achieve efficiency improvements in downstream mining processes is far from new. However, the author suggests that the practical application has become less than rigorous in a number of different sectors of the mining industry in a wide range of countries.There is a common tendency for the design process to become simplified to the point where the objective is merely the communication of instructions to field implementers (drillers, explosive suppliers, blasters, etc). In effect ‘design’ often degrades to ‘cut and paste’ with consequences that vary from mild to critical, with respect to the profitability of the business.Engineering of the drill and blast process involves the design function, not on a one-off basis but rather as a component of a more complete cyclical process that includes a statement of objectives, a design based on a suggested hypothesis, field measurement of results, comparison with the target ‘set point’ and the application of control measures followed by new measurement, including interpretation of the results in financial terms.When applied in this fashion, engineering provides practitioners with the means to optimise the drill and blast impact on the full spectrum business result of the mining activity.These concepts are discussed with reference to a surface gold mining operation applying run-of-mine heap leach extraction. Engineering optimisation by adapting process control and measurement techniques is demonstrated to be a key component of the solution set applied to generate enhanced operations productivity and stakeholder value. It is shown that a combination of rigorous measurement, model calibration and hands-on quality assurance/quality control facilitates the creation of a road map to profitability, stressing the need to consider economic trade-offs between operational expense (investment) and measurement of enhanced value (return on investment).The process, however, does not cease at this point. Implementation of true design practices, incorporating innovation and discipline in implementation or execution can drive the process to deliver demonstrable, technically validated outcomes. Furthermore, these technical results can be related to financially quantifiable impacts. However, this accomplishment does not guarantee that these gains or savings will reach the bottom line of those mining, quarrying and construction companies that begin the process with such high hopes.CITATION:Adamson, W R, 2015. Application of engineering discipline and a full-process optimisation focus – productivity to profitability without profuse pruning, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 3–12 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 24, 2015

By M Titley, M NoppT

A study on the feasibility of mining the recently discovered Wallaby gold deposit is due for completion by mid-2000. Open pit mining is the favoured method. Determination of the impact of mining bench height on the recovery of ore, including the estimation of dilution and ore loss, is critical to the economics of the operation. Conditional simulation was used to derive a number of gold estimation scenarios within a typical volume of the deposit. These scenarios were interrogated for a selection of mining bench heights and ore block dimensions. The results were reported as a range of grade tonnage relationships and compared to the kriged resource model. This allowed the resource model to be calibrated to a specific mining bench height and ore block size. Once calibrated, more realistic dilution and ore loss values for a number of mining bench heights were calculated from the resource model. These values were then used to determine the economic sensitivity of particular mining methods. The spread of results from the simulations also provided an indication of the confidence in the kriged grade estimates for the different zones of mineralisation within the deposit and highlighted areas of any significant uncertainty.

Jan 1, 2000

By M J. Gillespie, P D. Erskine

Mine site rehabilitation generally includes the re-shaping of overburden to create a final landform, manipulation of substrates and subsequent revegetation. Due to the wide range of environmental variables that influence rehabilitation progression, having clearly-stated final land-use goals and ongoing significant contributions to the planning process, from prefeasibility through to mine closure, is essential for achieving stable landforms and sustainable rehabilitated communities. Two examples of rehabilitation processes in the phosphate rich region of North West Queensland are used to illustrate some of the possible benefits of early planning and communication of rehabilitation requirements.Approximately 160 km south of Mount Isa, Incitec Pivot Limited operates a 35 year old open cut mine at Phosphate Hill. Monitoring of rehabilitation areas and selected analogue sites is undertaken annually, but the initial landform design, substrate management and species selection has created a difficult environment for revegetated areas to successfully establish. Constant management input (such as weed management, erosion control, supplementary seeding, etc) will, therefore, be required over a long time frame.The second example uses exploratory drilling and historic costean pits at Legend International HoldingÆs Paradise South site, 135 km north of Mount Isa, to determine the success of natural vegetation colonisation on waste rock and compacted soils, and the effects of cattle grazing on recolonisation. This information can be used by planners of the mine life to inform possible end-land use decisions and proposed completion criteria.In a semi-arid environment such as North West Queensland, the creation of a post-mine landscape suitable for nature conservation and/or grazing can be an arduous task. The input from environmental personnel at all stages of the mining process will positively impact upon the quality of the resulting rehabilitation and ensure undesirable legacy issues are minimised.CITATION:Gillespie, M J and Erskine, P D, 2012. Importance of early rehabilitation planning - Case studies from North West Queensland, in Proceedings Life-of-Mine 2012 , pp 187-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By A J. Morrison, M Yahyaei, J S. Siong, J Wang, K Runge

The flotation cells used to upgrade ultrafine metallurgical coal (-250 µm) are usually poorly controlled leading to unnecessary loss of combustibles from the flotation system. This is mainly because coal flotation cells are typically controlled for process stability rather than optimisation of flotation performance. This is especially true for a flotation device commonly used in coal applications in Australia – the Jameson Cell. This then provides an opportunity to improve the flotation performance by shifting from a stabilising control strategy to a proactive optimising control strategy. For an optimising control strategy, the control system will require a means of relating and then measuring in real-time, the effect of changing operating conditions on the coal flotation performance. Hence, the major aim of this work is to propose a possible model-informed process control strategy that could be used for real-time performance optimisation. In this study, industrial site work was conducted on an industrial-scaled Jameson Cell at a Coal Handling and Preparation Plant (CHPP) in Central Queensland, Australia where superficial gas velocity was controlled to six different levels. At the same time, other process variables such as froth depth and flotation feed properties were measured. The empirical models developed from this study suggested that combustible recovery is a function of superficial gas velocity, froth depth, feed solid content and feed ash content and that a peak in combustible recovery existed as a function of superficial gas velocity. This led to the development of a model-informed control strategy that aimed to maximise the combustible recovery by determining and then operating the cell at the superficial gas velocity at which the peak occurs. This peak superficial gas velocity was found to be only a function of feed solid content. Based on these findings it would seem possible to operate a Jameson cell at peak performance by online measurement of feed solid content, prediction of the optimum superficial gas velocity and stabilising control to maintain operation at that superficial gas velocity set point. The development of this modelinformed control strategy can serve as a basis for the development of a more sophisticated modelpredictive control (MPC) system. However, more work will need to be done to improve the predictivity of the combustible recovery model by measuring and modelling performance over a wider range of operating conditions.

Aug 24, 2022

By F D Durao, Muge F. H, Rogado J. Q

In the scope of the project named CAPUME II (EEC BRITE/EURAM contract - project MA2M-CT90,-0042(SMA)) for the development of an integrated mine planning system for underground mines, two of the main tasks were the development of a short-term mining planning procedure (module) and a numerical simulator of the mineral processing plant of Pirites Alentejanas - PA. The short-term mining planning module defines the mining sequences by solving a constrained minimisation problem. The ore grade variability is the objective function subject to the geometrical constraints of the mining method and to the maximum of `internal blending'. The optimisation problem is solved by applying a dynamic programming algorithm. The plant simulator is an essential tool of the planning system allowing the preview of metal grades/recoveries of copper, lead and zinc of concentrates streams, given the corresponding metal assays of the run-of-mine ore, defined by the short-term mine planning module. This way, the management can plan the short-term mining operations (the weekly sequence of exploration blocks and the internal planning) in order to fulfill given required conditions, based on a shipment schedule and on a purchaser's formula. In this paper, after a short description of the short-term mining planning module and of the simulation package named SIMUL, a synthesis of the main model development steps and the results of some simulation runs are presented and discussed.

Jan 1, 1995

By R E. Gerald II, B Zhang, T Sander, J D. Smith, J Huang, R J. O’Malley, H Tekle

In the steelmaking process, mold fluxes are essential for ensuring thermal insulation, refining, and the efficiency of continuous casting. Real-time understanding of the in-service composition of slags and fluxes are crucial for optimising the steel production process and improving the quality of the final product. An in situ fibre-optic Raman probe that enables the study of the structure, composition, and viscosity of molten slags and fluxes at steelmaking temperatures has been developed and demonstrated both in the lab and in foundry scale experiments. The focus of this study is on the structural, compositional, and property analysis of molten fluxes in a laboratory setting, with the aim of applying this technology for in situ monitoring during industrial production. Raman spectra were successfully collected at various temperatures from 1000°C to 1400°C in real-time and analysed using a deconvolution algorithm to isolate and quantify peaks in the spectra associated with the specific structures of molecular components in molten and solidifying flux. The research successfully combines in situ Raman spectroscopy with high-temperature viscosity data, specifically targeting CaO-CaF-SiO2-Al2O3 based mould flux systems. Specified ratios of the deconvoluted Raman peaks, such as Al-O-Al/Si-O-Si ratio, shows good correlation with the flux chemistry, while the Q3/Q0 peak ratio shows good correlation with viscosity. A ruggedised Raman probe system was also developed and demonstrated in an 80 kg induction furnace. Ultimately, the goal of this work is to demonstrate in situ slag and mould flux analysis in industrial processes, such as in the continuous caster or electric arc furnace (EAF).

Aug 21, 2024

By T O Aspinall

The Australian mineral industry involves a diverse range of expertise and skills. Within that, the mining industry, representing mine planning, mine management and equipment operation, has capital intensive, high productivity equipment and a small but skilled workforce. Continuing education for all personnel in the workforce after formal school courses will be an important contribution towards improving competitiveness. The non-tertiary sector represents a significant proportion of the workforce and requires as much attention as the tertiary educated group. Competency Based Training is now being developed for the mining industry in Australia under the National Training Board and the mining industry is well represented in establishing standards and curriculum. TAFE is a major source of accredited courses but some mining companies are also developing internal courses not necessarily for external accreditation. Articulation of such accredited courses to tertiary mining engineering courses has been considered. The education and training of equipment operators through continuing education requires attention to operating skills, an understanding of the productivity factors under the direct influence of the operator and providing product quality to the customer. The education and training of mining engineers has been widely covered and continuing close involvement of the mining industry is required to ensure well balanced courses in technical and interpersonal skills as well as motivation to continue learning for life. Postgraduate research is a part of continuing education but the mining industry has to continually address the adequate recognition of post-graduate qualifications for the increased technical or management expertise and the development of better analytical and problem solving skills which can be directed towards improving competitiveness. More attention has to be paid to providing adequate financial incentives to attract suitable students, particularly after attaining some experience, and to address their professional career path with a company so they are not significantly disadvantaged by undertaking post-graduate studies. The Chartered Professional Engineer status as provided by The Institution of Engineers, Australia to qualified candidates is being considered by The Australasian Institute of Mining and Metallurgy as a further recognition of a member's specific expertise and competence in mining and metallurgical engineering. Continuing education plays a major part in the maintenance of the expertise and competence required for a professional engineer to develop and also to retain chartered status. Continuing education will be a significant part of the education and training of all the mining workforce towards improving the competitiveness of the mining industry. The major challenges will be the motivation of all towards lifelong learning and the integration of the various programs towards providing the opportunity for a steady and satisfying career progression.

Jan 1, 1994

By A R. Firth

The induration furnace for iron ore pellets was originally designed to process concentrates with high contents of magnetite. To support the use of haematite concentrates, internal fuel was added to the pellets in the form of ground coke breeze or anthracite. To ensure that the addition of coke breeze was not excessive, the ‘heat of magnetite equivalent’ or heat of magnetite equivalent (HME) relationship was developed, guaranteeing that the fi ring temperature requirements remained the same. However, this oversimplifi es the different reaction paths of magnetite and carbon in iron ore pellets. At fi ring temperatures, gas diffusion controlled reactions such as the combustion of coke, the calcination of carbonates and the reduction and oxidation of iron oxides can all occur in different parts of the pellet simultaneously. The interaction of these reactions produces a range of atmospheres across the diameter of the pellet that vary from oxidising at the pellet shell to reducing at the pellet core. Mathematical modelling and pellet fi ring experiments to preheat temperatures before quenching have shown that a higher proportion of coke relative to magnetite slows down the oxidation process, irrespective of temperature. A higher temperature, however, results in an increase in the rate of haematite reduction in the pellet core and a more reducing atmosphere, which could lead to different sintering rates in different parts of the pellet and shrinkage cracks forming. To observe these gas-solid reaction rates at a larger scale, the COREM pot grate has been updated with an additional oxygen analyser. This, along with other improvements, will allow better optimisation of straight-grate firing cycles for different pellet compositions.

Jul 11, 2011

Jan 1, 2004

By U Dzharlkaganov, B Bekmurzayevand M

The principle conception is presented of timely planning of winning operations in complex-structural blocks and faces in week-24-hourly regime. For adequate description of complex interconnections of open cast operation in space and in time and solving of optimisation problems in timely regime it is necessary using of complex logical and calculation procedures.

Jan 1, 2003

By Matveeva TN, Lunin VD, Ivanov VA

The results of theoretical and technological investigations have been presented for the application of electrochemical technology in copper-nickel flotation processing schemes. The sorbed xanthate and dithiophosphate products on chalcopyrite and pyrrhotite have been studied in distinct polarisation conditions of mineral suspensions. Optimum electrochemical pulp treatment parameters have been worked out for copper, nickel, pyrrhotite and other flotation cycles. The method has been examined in pilot plant conditions over a long period of time, technological efficiency has been evaluated corresponding to the industrial flotation process at the Norilsk plant.

Jan 1, 1993