Search Documents

By G. F. Comstock

THE subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: (1) That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. (2) That the quality of the metal and the mill practice must have something to do with them. The first point of view was most-ably and logically presented by J. E. Howard,1 and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these. failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior roach-bed; while the railroad men,, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work clone in this laboratory, as well as the work of other investigators of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. . Within the last year or two, however, since the method of etching polished sections for the microscope with a cupric chloride solution has been tried systematically. on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 11, 1918

BASIC open-hearth slags have no obviously unique features when compared with slags from other metallurgical operations. Open-hearth slags form and exist at temperatures ranging from 2500 to 3100 F (1370 to 1700 C). In the course of an open-hearth heat, the liquid slag changes slowly and continuously in chemical analysis-the changes reflecting changes in temperature, changes in metal analysis, solution of charged materials, solution of feed additions, and solution of refractories. Throughout the process, the slag performs specific primary functions that are responsible for a large measure of the technical and economic importance of basic open-hearth steelmaking. It is intended in this chapter to present the chemical reactions by which the primary functions of basic open-hearth slags are carried out, to describe the physical and chemical principles governing the extent to which these reactions proceed and can be regulated, and finally to indicate the limitations imposed on other features of the process by the fulfillment of the primary functions. Basic open-hearth slags perform three primary functions. First and foremost, the slag provides a means of removing phosphorus from the liquid metal. The ability to remove phosphorus is largely responsible for the widespread use of the basic open-hearth process. Second, the slag serves as a controlling factor in transferring the oxygen required for the other oxidizing reactions. Third, the slag provides a means of eliminating some sulfur from the open-hearth bath. While the extent of sulfur removal is not comparable to that of phosphorus, the ability to remove some sulfur contributes much to the value of the process. The effectiveness with which the slag fulfills its functions varies with temperature and composition. Since operating temperatures are fixed largely by the specified nature of the product and the equipment, .the speed and extent to which the functions of the slag are carried out depend largely on its composition. The necessity for regulating slag composition to accomplish the re-

Jan 1, 1964

GOD the Almighty has all things well ordered; in G particular, the effects and attributes of the seven planets whose reign and course (by the grace of God) determine for the most part not only our own life and death but also the growth and decay of vegetable and mineral life, so that the aforesaid planets generate and develop in a wondrous way the ores of gold and other metals in minerals, rocks, and earths. Specifically, the Sun develops the ores of gold, the Moon the ores of silver, Venus the ores of copper, Saturn the ores of lead, Jupiter the ores of tin and bismuth, Mars the ores of steel and iron, and so on. Since, however, no ore is made alone but each is made and wrought so that it is associated with other ores, it is necessary to know the art of separating the thus-made ores after they have become metals; as for instance, silver from lead and copper; gold from silver, and so on. [2]* If this is to be done usefully, you must be able to assay and must understand everything that is needed in connection therewith. It is obviously true and clear as light of day that some kinds of copper contain silver and some kinds of silver contain gold. In order that you may be able to separate them, so that each is obtained by itself and can be worked with profit and re ward you need first of all a true assay for the values of such metal. The assay, by revealing how great they are, whether the pure has been obtained separate from the worthless matter, and what the admixture is, advises you whether it would be worth the expense and the effort to start mining operations. Assaying also indicates how much silver there is in a centner of ore or how much copper and lead there are in

Jan 1, 1949

By Thomas Lane Carter

The history of mining in South Africa differs somewhat from that of other countries in the part taken by the aborigines in the development of the mineral deposits. The Spaniards in America, and the fortune-seekers of Australia and New Zealand, found large numbers of natives in these new countries, but the inhabitants did not become willing or efficient workers in the mines which the white men started. The Kaffirs of South Africa have not shown the same antipathy to labor, nor do they show any signs of dying out in the presence of the white man's civilization. They are a virile race, and so far the vices of civilization have not killed them. While it is true that the brain and skill necessary for the exploitation of the mineral resources of this sub-continent have been supplied by the white race, it is also a fact that most of the rough labor in the development of the mining industry of South Africa has been done by the Kaffirs. The Kaffir tribes differ greatly in their mental and physical capabilities. Compare, for instance, a Zulu of Natal with a Bechuana, or a Xosa of Cape Colony with some of the degenerate tribes of Central or East Africa, and you will find that they have little in common, save that their skin is black and that they do not believe in clothes. As a general rule, the tribes in the milder, healthier climates are far superior, both in mind and body, to the Kaffirs brought up in the hot malarial sections of Central Africa; and it naturally follows that the black men from the temperate zones of the country are much finer workmen than the degenerates from less favorable sections. It is universal in South Africa to speak of the Kaffirs as " boys." No matter if he is 90 years old, the Kaffir is always a a boy," and in this paper the word " boy " is synonymous with Kaffir.

Jan 1, 1909

By J. E. Johnson

Discussion of the paper of Bradley Stoughton, presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912, pp. 1245 to 1275. J. E. JOHNSON, JR., Ashland, Wis. :-Is it true that titanium reduces the chill in chilling iron? If so, as I think Mr. Stoughton has stated elsewhere, then I do not see how titanium is beneficial in car-wheel mixtures. One of the most difficult things to do is to get a proper chill and a proper degree of toughness, and the goodness of an iron of the given composition for charcoal-iron purposes is denoted by the chill which it will take as compared with its composition. If titanium reduces that chill, then it does not seem to me as good for car-wheels as its absence would be, and I should like to have it explained what effect titanium has on the chill of a given iron. MR. STOUGHTON : It is true that titanium reduces the chill of iron quite noticeably, yet, at the same time, if I am correctly informed, 90 per cent. of all chilled-iron rolls are made to-day with the titanium treatment, and a great many car-wheels, but one has to make changes in the silicon added and also, if I am correctly informed, in the manganese. The advantage of titanium is that when the proper changes are made, so that we get the same depth of chill with the titanium as we otherwise would without, the chill is much harder than before, and also the body of the roll or wheel is tougher and somewhat stronger, especially under shock. JAMES F. KEMP, New York, N. Y.:-This subject is obviously one of great importance to the iron industry, in that if we call find a method of using titaniferous ores, we will prolong the life of our iron reserves. Fifteen or more years ago, primarily from the study of the ores in the Adirondacks, I be-

Dec 1, 1912

By S. W. Miller

During the examination of welds made in steel by the oxy-acetylene and electric-arc processes, the writer has met with some unusual structures, which he has not encountered elsewhere. They seem to be quite closely associated with the welding methods used, and characteristic of them, and would seem to be worth noting, especially as the references to them in the literature are few, and their explanation not clear or complete. An introductory word or two about fusion welding may not be out of place. The oxy-acetylene process is based on the great and very local heat generated by the burning of acetylene in the presence of commercially pure oxygen, the two gases being thoroughly mixed before combustion. The theoretical temperature is somewhat under 4000" C, but on account of various losses, the actual maximum temperature is probably about 3000" C.' The electric-arc process, using a metal electrode, which is also the filling rod, generates a still higher and more local temperature. The actual temperature of the positive crater of the carbon arc is given as 3500" C.2 NO figures have been found for the temperature of the arc using a metal electrode, but it would probably not be very different from that of the carbon arc, and probably higher than that of the bxy-acetylene flame. The greater localization of the electric arc is due to the fact that it is not surrounded by a large envelope flame, as well as to its higher temperature; while the oxy-acetylene white cone, or welding flame, in which the carbon of the acetylene is burned to CO, is surrounded and preceded by a long envelope flame, itself of quite high temperature, in which the CO is burned to GO2, and the hydrogen of the acetylene to H2O. This flame spreads around and over the pieces being welded, heating them to a further distance from the weld than does the electric arc.

Jan 1, 1918

By E. H. Bunce, H. M. Haslam

The "direct process" for the manufacture of pigment zinc oxide produces the oxide directly from ore. This is accomplished by reducing the zinc by means of carbonaceous fuels and immediately burning the evolved zinc vapor to zinc oxide. For many years this was done by smelting a loose charge of ore and fuel on perforated grates. Since this process was developed in America and was extensively used here, it has become known as the "American process." Alternative methods of producing pigment zinc oxide are the "indirect process " and the "wet process." In the indirect process the raw material is metallic zinc, which is volatilized and burned to the oxide. For a long time this has been done in externally fired horizontal refractory retorts. This process has become known as the "French process," from the country of its origin. The wet process precipitates the carbonate or hydrate from zinc-bearing liquors and then calcines the precipitate. This method has been but sparingly used for producing commercial quantities of zinc oxide. It appears to be advisable to restrict the use of the terms "American process" and "French process" to the methods of the earlier periods and to consider the terms "direct process" and "indirect process" as generic terms to designate, first, all methods of producing pigment zinc oxide directly from ores, and, second, to include all those methods of producing zinc oxide from metallic zinc and metallic zinc-bearing substances. American Process In 1796 John Atkinson was granted British Patent No. 2094/1796 entitled, "Manufacture of White Paint." This patent describes a method of producing zinc oxide in which roasted zinc blende or calcined calamine is mixed with charcoal, and the mixture heated in a muffle to liberate zinc vapor, which is then burned to obtain zinc oxide fume. About 1850 The New Jersey Zinc Co., at its plant in Newark, N. J., attempted to make zinc oxide by smelting, in a reverberatory furnace, a mixture of coal and ore from its Franklin mine. A considerable amount

Jan 1, 1937

By Arthur Winslow

Introductory.—The following paper is based upon a report on the lead- and zinc- deposits of Missouri, prepared for the State Geological Survey, which is now being printed. This report is the outcome of work prosecuted by the writer, assisted by Mr. J. D. Robertson, during the past five years. The studies in the State were supplemented by examinations of the similar ore deposits in Wisconsin and Arkan- sas. The report will contain in all about 800 pages, and the aim has been to make it complete and exhaustive, especially in descriptive matter. Naturally, only a brief outline can be presented here, and the reader is referred to the report itself for further details. Contents. I.—History and Statistics, . . 636 II.—Topography of the Region, . 639 III.—General Geology, . . .639 The Archean, . . .639 The Algonkian, . . 640 The Silurian, . . .640 The Devonian, . . 640 The Lower Carboniferous, 641 Tie Coal Measures, . 641 The Tertiary, . . .641 Structural Geology,. . 642 IV.—The Ore-Deposits, . . .643 Geologic Distribution, . 643 The Forms of the Ore-Bodies, . . .641 The Composition if the Ore-Bodies, . . .645 Gangues, . . . 645 Minerals, . . .618 Paragenesis of Minerals, . . . 651 The Structure of the Ore-Bodies, .... 651 V.—Descriptions of Types, . . 652 The Eagle Mines, . . 652 Shaft No. 23, . . 652 The Western Zinc Company or Oswego Lands, 651 The Gobar and Tomlinson Shaft, . 655 The Alba Company's Mine, 656 The Victor Mine, . . 658 The Bonne Terre Mines, . 660 General Geology, . 660 The Ore-Bodies, . 661 The Vallé Mines, . . 664 The Garatee Mines, . 664 The Corn-Stalk Diggings, . . .665 The Virginia Mine, . 666 The Conlogue Mine, . 667 VI.—The Mode of Formation of the Ore-Bodies, . . 670 The Formation of the Cavities. . . . 670 The Filling of the Cavities, . . . .675 The Formation of the Breccia Deposits, . . 673 The Formation of Circle Deposits, . . .674 The Impregnated Deposits of the Southeast, . 676 VII.—The Origin of the Metalliferous and Other Minerals, 676 1. Originally Deposited in Concentrated Condition, 676 2. Derived from Great Depths, . . .677 3. Original Diffusion, Supplemented by Lateral Secretion, . . . 678 4. Concentrated Through Surface Decomposition, 681

Jan 1, 1895

By E. H. Jr. Dix

IN selecting the subject, "Acceleration of the Rate of Corrosion by High Constant Stresses," for the 1940 Institute of Metals Division Lec-ture, I have been influenced by its highly theoretical and speculative nature as well as by the great practical importance of the correct inter-pretation and appraisal of the engineering significance of the phenomenon. I lay no claim to originality in talking on this topic, since it has been the subject of discussion for over a quarter of a century. However, as our technical thinking advances, old phenomena take on new and more significant aspects. In our studies at the Aluminum Research Labora-tories, we have encountered many perplexing and seemingly contradictory results and have been fascinated by the problem of dovetailing all of the many pieces of information to make a complete picture. I hope that in the brief period of this lecture I may share with you some of the enjoy-ment we have had in attempting to meet this challenge to metallur-gical science. The emphasis generally has been placed on the spontaneous failure by cracking of a metal under the combined action of high stress and corrosion, hence the present-day use of the terms "stress corrosion" or "stress corrosion cracking." The older term "season cracking," applied more specifically to copper-base alloys, includes, by inference, the element of time. For the purpose of the discussion today I will use "stress corro-sion" to cover broadly the effect of stress in accelerating the rate of corrosion of metals. To stay within the limits of allotted time the dis-cussion will cover the effect of high static stresses rather than repeated or dynamic stresses, which would take us into the related field of corro-sion-fatigue. The subject is particularly appropriate for an Institute of Metals Division Lecture because much the same phenomenon has been observed in almost all metal systems. Thus, in addition to the season cracking of brass may also be mentioned the "caustic embrittlement" of steel boiler

Jan 1, 1940

By Paul M. Tyler

Mineral raw materials, because they are essential to our industrial prosperity and military strength, must be made available in substantial quantities regardless of cost. Variations in the cost of procuring minerals, as compared with the cost of obtaining other commodities, and changes in the cost of production of different minerals relative to one another, will naturally influence the quantities of a given mineral item that can be marketed readily. However, in the last analysis, the cost of winning minerals from the ground usually constitutes only a small fraction of the value of the end-use products and services derived from them. The miner's share of the cost of a typewriter, telephone circuit, or even a modem office building, is almost insignificant. Far more important to the ultimate consumer, therefore, than any minor saving in cost is the assurance of ample supplies of the minerals needed to aliment our expanding economy. To create a successful metal mining operation involves (1 ) the discovery and systematic development of a mineral deposit, (2) extraction of the ore, (3) the mechanical and metallurgical processing to eliminate worthless or harmful impurities, and (4) the profitable disposal of the product. The fist step of the technological process belongs chiefly in the realm of the geologist, the second is a mining engineer's job, the third is mainly up to the millmen and extractive metallurgists; whereas the fourth and equally important step poses a commercial problem that has aspects in common with the marketing of other products. Ore finding is far from being an exact science. There is no mathematical criterion for evaluating the efficiency of prospecting and exploration. Lady Luck shares the honors or assumes part of the blame along with the prospector and geologist. Marketing like- wise involves factors that seemingly defy engineering analysis. Although the other steps can be measured with some degree of mathematical accuracy, even they tend to vary so widely in basic principle, as well as in

Jan 1, 1964

By Frank Alfred Fahrenwald

MetallURgical research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been , found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likeiy that a material can be produced which, will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series1 has shown that alloys of those metals maybe produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties—including the ease with which it may be soldered—are invaluable. But it is most extensively used in

Jan 1, 1916

By Frank Fahrenwald

I. INTRODUCTORY METALLURGICAL research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likely that a material can be produced which will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may, be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series' has shown that alloys of those metals may be produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties-including the ease with which

Jan 1, 1916

By W. H. Bassett

A 10-year, sea-water, corrosion test of tubes of several copper alloys has shown that many alloys withstood attack by solution, pitting, and dezinkification; a 1-year, salt-spray test of sheet-metal specimens of the same composition showed the same results. THE late J. P. Sparrow, chief operating engineer of the New York Edison Co., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in' September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40, 70-30, 80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period.

Jan 1, 1925

By Zay Jeffries

EACH generation accepts the developments of the preceding generations without full appreciation of the difficulties that had to be overcome or of the effect of any given development on society. Today, the production of pig iron is the yardstick with which general industrial health and progress are measured. So natural and logical does this seem to us, that it is difficult to picture conditions prior to the fourteenth century when pig iron was unknown. Not only was pig iron unknown but iron or steel could not be melted and poured into castings; all iron and steel articles were forged from sponge iron. All castings, as well as many worked articles, were made of non-ferrous metals or alloys. In many parts of the world, over long periods of time, not only was the annual exchange value of non-ferrous metals greater than that of iron and steel, but their combined tonnage was greater. At present, the value of the pig iron produced in a year is of the same order of magnitude as that of all non-ferrous metals combined; the tonnage of pig iron is, however, about twenty times that of all non-ferrous metals combined. Owing to lack of records, we will probably never know the relative importance of the various metals at all periods in historic times. A certain conclusion is that the iron and steel industry, since the discovery of pig iron and the cheap methods of converting it into steel, has grown at a much more rapid rate than the non-ferrous metal industries. Notwith-standing their fundamental fitness for man's needs, iron and steel owe their importance in no small degree to the low cost of production. The low cost was a result of increased knowledge of the production appliances and of the metallurgical processes. This increased knowledge is the key to our modern industrial civilization.

Jan 5, 1924

By C. H. Mathewson

MICROSCOPIC. rnetallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent microstructural mosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of 'particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientations and it is always possible to derive one from the other by some form of rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By C. R. Austin

THE paper describes an investigation on the pressure welding of low-carbon steels. The work necessitated a reproducible mechanical means of making the weld and also a test that would indicate the nature and completeness of the union. An apparatus including a high-temperature furnace was devised for making the welds, and the ordinary tensile pulling test 'in correlation with macroscopic and microscopic observations was used as a means of examining the result. Initially it was intended to devise some simple test of weldability, but as the experimental work progressed, it soon became clear that with our limited knowledge of the exact nature of the mechanism of pressure welding it was impossible to interpret our results or to devise a simple test of weldability. Hence it was manifestly necessary first to study the mechanism of such welding and attempt to elucidate the fundamentals underlying the so-called welding of steel by pressing together two metal surfaces. It also became evident that it was necessary to define the term "welding." In many early experiments when, two heated rods were pressed together and then pulled in the cold, very high tensile values were obtained, and yet the fracture took place exactly in the line of junction except for a few small scattered areas. In other words, the' rods pulled apart just as they were before being "stuck" together and had certainly not welded completely, despite the high value indicating the strong cohesive force operating. In this paper, welding has been considered as a form of intimate contact between two metal surfaces, so that the units lose their individual identity and there is no change in physical properties in passing through the weld from one unit to the other. This is defined as "true welding." When true welding has taken place completely over the whole section, the probability is that the rupture in tensile test will occur outside the weld.

Jan 1, 1932

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

0. C. Ralston and F. Fraas—Dr. Sun and associates have presented an interesting paper not all of which is comprehended by us. The data assembled measure the deflections of particles in an electrostatic field as a function of a number of independent variables and some dependent variables that are not sharply differentiated. These data are all based on a Johnson type machine of definite, well-described geometry, something not often done in electrostatic separation literature. One new fact brought out by this technique is the effect of coal dust on admixed pyrite and quartz. The effects are opposite in character, as should be expected and we do not agree with the authors that these effects are negligible. Fraas' also used a multiple cell "distribution analyzer" and gives in fig. 5 of his paper a straight line plot with no humps or curves. This is not necessarily at variance with Sun's results because Fraas used a larger gap between electrodes and had no evidence of particles adhering to or dropping off the charged electrode. The section of Sun's paper on effect of surface conductivity contains a speculation that the dielectric constant "represents more or less the electrical conductance of the bulk body instead of the surface of the mineral particles." A simple picture of the meaning of the dielectric constant is that it is the specific inductive capacity of a dielectric when used as the dielectric between the plates of a condenser. It is at once evident that the above speculation confuses capacity with conductance—two definitely independent variables. We ask the authors to state in what group or subdivision their garnet belongs; what method and units were used in calculating the data of col. A, table I and their meaning; what was the temperature of the carrier roll and, finally, has any effort been made to investigate the effects of particle shape on distribution in the electrostatic field? S. B. Hudson—I have read this article with great interest. We have been engaged in research work on the principles of electrostatic separation in this laboratory for some time now, and our findings agree with those of the authors in many respects. The article shows evidence of careful and valuable research in the field of electrostatic separation. A "distribution analyser," very similar to that described in an earlier article by one of the authors," was incorporated in an inclined plate-type electrostatic separator designed and built in the Melbourne University laboratory in 1948 for investigation purposes.22 The actual splitting edges were machined from y! in. per-spex, and the paper hoppers were supported on linen thread immediately below the perspex dividers. These dividers fitted into machined slots in a framework to give accurate Yz-in. spacings. The hoppers (staggered) fed directly into a rack of test tubes, which is supported on a vertical pantograph arrangement. The rack was positioned with guides on the horizontal pantograph stand, and this ensured positive alignment when replacing the rack after making weighings. In later work, when much heavier feed rates were used, of the order of 30 to 40 Ib per in. per hr a rack fitted with rectangular metal containers and similarly aligned was used. Some work was done here on comparing the distributions of minerals when passed separately and when passed as a mixture, and it was found that there was quite an appreciable difference in the two results.= However, in our separator the particles do not pass down the plate in a single layer, and this difference is probably caused by collisions of one mineral particles with the other mineral particles. In most of the investigational work here, the change of the center point of the distribution is measured to establish the effect of a variable, such as voltage. Two minerals (zircon and rutile) have been studied rather exhaustively, and it was found that their distributions are very nearly normal. Owing to the sharpness of the distribution curves, the usual method of obtaining the mean or median was inaccurate, and was not used; instead the mean (also the median), calculated on the assumption of a normal distribution, was used to locate the center point of each distribution and proved satisfactory. The effect of polarity becomes very apparent in the plate-type separator where frictional charges play a very important part when using highly resistive minerals such as zircon. With rutile, a comparatively conductive mineral, polarity of the electrode has little effect. On the other hand, the magnitude of the voltage has a far greater effect on conductive than on resistive minerals. Shiou-Chuan Sun (authors' reply)—Thanks are extended to Drs. Ralston and Fraas for their keen interest in this paper. Their questions concerning coal dust,

Jan 1, 1951

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

0. C. Ralston and F. Fraas—Dr. Sun and associates have presented an interesting paper not all of which is comprehended by us. The data assembled measure the deflections of particles in an electrostatic field as a function of a number of independent variables and some dependent variables that are not sharply differentiated. These data are all based on a Johnson type machine of definite, well-described geometry, something not often done in electrostatic separation literature. One new fact brought out by this technique is the effect of coal dust on admixed pyrite and quartz. The effects are opposite in character, as should be expected and we do not agree with the authors that these effects are negligible. Fraas' also used a multiple cell "distribution analyzer" and gives in fig. 5 of his paper a straight line plot with no humps or curves. This is not necessarily at variance with Sun's results because Fraas used a larger gap between electrodes and had no evidence of particles adhering to or dropping off the charged electrode. The section of Sun's paper on effect of surface conductivity contains a speculation that the dielectric constant "represents more or less the electrical conductance of the bulk body instead of the surface of the mineral particles." A simple picture of the meaning of the dielectric constant is that it is the specific inductive capacity of a dielectric when used as the dielectric between the plates of a condenser. It is at once evident that the above speculation confuses capacity with conductance—two definitely independent variables. We ask the authors to state in what group or subdivision their garnet belongs; what method and units were used in calculating the data of col. A, table I and their meaning; what was the temperature of the carrier roll and, finally, has any effort been made to investigate the effects of particle shape on distribution in the electrostatic field? S. B. Hudson—I have read this article with great interest. We have been engaged in research work on the principles of electrostatic separation in this laboratory for some time now, and our findings agree with those of the authors in many respects. The article shows evidence of careful and valuable research in the field of electrostatic separation. A "distribution analyser," very similar to that described in an earlier article by one of the authors," was incorporated in an inclined plate-type electrostatic separator designed and built in the Melbourne University laboratory in 1948 for investigation purposes.22 The actual splitting edges were machined from y! in. per-spex, and the paper hoppers were supported on linen thread immediately below the perspex dividers. These dividers fitted into machined slots in a framework to give accurate Yz-in. spacings. The hoppers (staggered) fed directly into a rack of test tubes, which is supported on a vertical pantograph arrangement. The rack was positioned with guides on the horizontal pantograph stand, and this ensured positive alignment when replacing the rack after making weighings. In later work, when much heavier feed rates were used, of the order of 30 to 40 Ib per in. per hr a rack fitted with rectangular metal containers and similarly aligned was used. Some work was done here on comparing the distributions of minerals when passed separately and when passed as a mixture, and it was found that there was quite an appreciable difference in the two results.= However, in our separator the particles do not pass down the plate in a single layer, and this difference is probably caused by collisions of one mineral particles with the other mineral particles. In most of the investigational work here, the change of the center point of the distribution is measured to establish the effect of a variable, such as voltage. Two minerals (zircon and rutile) have been studied rather exhaustively, and it was found that their distributions are very nearly normal. Owing to the sharpness of the distribution curves, the usual method of obtaining the mean or median was inaccurate, and was not used; instead the mean (also the median), calculated on the assumption of a normal distribution, was used to locate the center point of each distribution and proved satisfactory. The effect of polarity becomes very apparent in the plate-type separator where frictional charges play a very important part when using highly resistive minerals such as zircon. With rutile, a comparatively conductive mineral, polarity of the electrode has little effect. On the other hand, the magnitude of the voltage has a far greater effect on conductive than on resistive minerals. Shiou-Chuan Sun (authors' reply)—Thanks are extended to Drs. Ralston and Fraas for their keen interest in this paper. Their questions concerning coal dust,

Jan 1, 1951

By C. C. Miller, A. B. Dyes

The cost of finding and developing new reserves is continually rising. We must meet these rising costs with more economical operations. This can he accomplished if we revise our ideas of proper well spacing and well allowable to consider the concept of optimum well spacing. According to this concept, the optimum spacing is the one which leads to the maximum present worth for a reservoir when ail factors affecting total cost and total revenue are considered and when the wells are produced in the most eficient manner. Application of this principle efficiently utilizes available well potential and properly considers the recovery eficiency in addition to fixing the spacing on the basis of the amount and value of the oil to he recovered. This Study presents an analysis of one producing zone containing low gravity crude to illustrate the effect of these factors on the present worth and on the optimum economic spacing under two production drives—-evolved gas and water drive. The maximum present worth occurs when the optimum number of wells for open-flow operation is employed. Frequently, this optimum development cal1s for very wide spacing and the ideal field rates are not unreasonable. Under other circumstance. where proration is necessary, an optimum combination of well spacing and well allowable exists which permits production at relatively high rates. The optimum well density in a field depends on the recovery efficiency and the valule of the oil. In solution gas-driven reservoirs this optimum spacing for operation at high producing rates can vary from extremely wide spacing to handle viscous low gravity oil in thin formations to relatively close spacing in thick sands where good recoveries are expected. Because of the better recovery from water-driven fields, the optimum spacing in these fields is closer than in solution gas-driven fields. Also, the water encroachment pattern is dependent upon the well spacing, and an adequate numher of wells is needed to assure a good sweep eficiency. The economic optimum well density in a water-driven field is high enough for this purpose. INTRODUCTION From year to year domestic oil becomes more difficult to find. The fields we do locate are frequently smaller and deeper than older fields and the costs for men, material and equipment are continually rising. To replenish our reserves we must continue to search for and develop new fields, but experience has shown we cannot expect prices to rise in proportion to costs. Consequently, we must meet increasing costs by more economical operations. A vigorous effort is being made within the industry to improve exploration methods, to cope with the problems of deeper drilling, and to obtain a secondary yield from older fields. Many significant contributions have resulted from these efforts. The economic operation of new fields can be further improved by developing these fields on optimum spacing and producing the wells at higher rates. This would avoid the drilling of unnecessary wells and provide additional capital for seeking new oil. While the benefits of these practices are obvious, the problem of defining the optimum development of a field for natural depletion can become very complex. A study of the effect of well spacing and several reservoir variables on economic worth of a specific field is reported here to illustrate the problem and to show the magnitude of the benefits to be realized. This study is necessarily limited to the field conditions selected and is not intended as a general solution of the well spacing problem. It does, however, indicate factors to be considered, the trends to be expected, and the direction in which we should proceed in developing new fields. NO consideration is given to land and legal considerations which might arise. METHOD OF ANALYSIS The optimum method of developing and producing a field is to use the combination of spacing and prora-tion which gives the maximum return. In addition, we do not want to lose recovery. These considerations of maximum return and maximum recovery present no serious conflict. The value of each method of operation is conveniently expressed in terms of its present worth. According to the present worth method of evaluation,' an acceptable annual percentage return is assigned to the operation, and all incomes, capital costs, and expenses are discounted at this rate to the start of the operation. This net value is the present worth. If we apply the same discount rate to several alternate methods of operation, the one yielding the greatest present worth is the best method. If we express net income in terms of price per barrel of oil produced, drilling and equipment costs on a well basis, and expenses as cost per well year, this evalu-

By R. W. Balluffi, R. Resnick

NUMEROUS investigations of chemical diffusion in a brass have been made and the results are collected in several places.1-3 This work has been mainly concerned with the determination of the chemical diffusivity as a function of composition and temperature. In 1947 Smigelskas and Kirken-dall&apos; showed that zinc and copper diffuse at different rates in face-centered-cubic brass, and since then, a number of efforts have been made to determine the intrinsic diffusivities of zinc and copper in this alloy.1, 5-9 Horne and Mehl8 in particular have recently determined the intrinsic diffusivities as functions of temperature and composition using sandwich-type couples and inert markers. Inman et al." also have determined the intrinsic diffusivities in homogeneous alloys using tracer techniques. When the present work was started, no information of this type was available. Consequently, measurements of the intrinsic diffusivities were made as a function of temperature at a constant composition of 28 atomic pct Zn with vapor-solid diffusion couples where the zinc was diffused into the diffusion couple from the vapor phase. The application of these couples to the study of diffusion in a: brass has been described previously.0,7 The temperature dependence of the intrinsic diffusivities was found to follow the relation D, = A, exp(-Hi/RT) and the values of Hzn, and Hcu, were found to be closely the same. It is emphasized, however, that the chemical dif-fusivity (D = N1D2 + N2D1) is a composite diffusivity and does not necessarily follow this exponential form. It is usually found to do so within experimental error for substitutional alloys because the heats of activation of the intrinsic diffusivities generally are not greatly different.&apos;" Also, at the onset of this work, there was no information available concerning possible unequal diffusion rates of individual components and the existence of a Kirkendall effect in alloys with other than face-centered-cubic structures. Since then, two reports indicating a Kirkendall effect in body-centered-cubic ß brass have appeared. Landergren and Mehl" have published a note describing Kirkendall diffusion experiments with sandwich-type couples. Inman et a1.9 also find a Kirkendall effect in this alloy using the tracer technique. In the present work, several aspects of the Kirkendall effect in ß brass were further investigated using vapor-solid couples. Two different couples were used, one in which the zinc was diffused into the specimen from the vapor phase and the other in which the zinc was diffused out of the specimen into the vapor phase. Briefly, the existence of a Kirkendall effect is confirmed and it is found that Dzn/Dcu = 3 at about the 46 atomic pct composition in this alloy at 600°, 700°, and 800°C. As a result of the unequal diffusion rates of zinc and copper, volume changes occur and subgrain formation is observed in the diffusion zone. In addition, significant porosity is produced by the precipitation of supersaturated vacancies. Diffusion in this alloy is therefore outwardly similar to diffusion in a brass where these effects are also observed, a Brass Experimental Methods—The use of vapor-solid couples in studying diffusion in a brass has been described in previous articles.6,7 The method briefly consists of sealing a copper specimen with Kirkendall markers initially placed on its surface in an evacuated quartz capsule along with a large zinc source of fine a brass chips and then diffusing the zinc into the specimen through the vapor phase. The zinc concentration at the specimen surface rises rapidly enough to a value near that of the a brass source so that the surface concentration may be regarded as constant during diffusion. Under these boundary conditions, values of the chemical diffu-sivity may be obtained by applying the Boltzmann-Matano analysis to the concentration penetration curve, and the intrinsic diffusivities may be obtained from Darken&apos;s5 equations when the velocity of marker movement is known. The diffusion specimens were made from OFHC copper in the form of disks 3.2 cm diam and 0.5 cm thick with faces surface-ground parallel to within +0.001 cm. Markers in the form of fine alumina particles <0.0002 cm diam were placed on the specimen surface. These specimens were then sealed in quartz capsules along with enough a brass chips of a 30.0 atomic pct Zn composition to keep the source concentration from decreasing by more than 0.3 atomic pct Zn as a result of the loss of zinc to the specimen during diffusion. The quartz capsules which were initially evacuated to a pressure of

Jan 1, 1956