Search Documents

By M. L. Fuller

The fundamental mechanism of the deformation of zinc has been thoroughly described by several prominent investigators, particularly Mark, Polanyi, and Schmid,1 Mathewson and Phillips,2 and Schmid and Wassermann.3 The deformation of zinc occurs primarily through slip along basal planes (00.11, and secondarily through twinning on pyramidal planes of the form (10.2). In addition to these basic studies on single crystals, there have been a number of determinations4,5 of preferred orientations developed in rolled, polycrystalline zinc. In no case, to our knowledge, has there been described the development of oriented structures in zinc as a result of a systematic series of rolling treatments. The work included in the present paper shows the changes in orientation produced in a zinc alloy by successively increasing degrees of cold-rolling reduction. This alloy has the same crystal form, hexagonal close-packed, as zinc, but its susceptibility to hardening for a given degree of working is much greater because of its higher recrystal-lization temperature. Experimental Procedure Composition of the Alloy and Rolling Treatment The alloy used in this investigation consisted of zinc of 99.9 per cent purity to which 1 per cent of copper and 0.01 per cent of magnesium had been added.

Jan 1, 1934

By T. Clinton Taylor

QUALITATIVELY, galena (native lead sulfide) reacts with aqueous solutions of the xanthates,1 and has its surface sufficiently altered so that there is a tendency for air bubbles to attach themselves to the mineral crystals where there was no such effect before the treatment. This property is utilized in froth flotation operations where the mineral sulfide particles are raised into the froth and the gangue whose surface is not altered remains behind. The results of a study of this reaction were reported" recently and certain tentative suggestions about the interaction of galena and the alkali xanthates were offered. In this paper, there is set down the results of a detailed quantitative investigation of the ions involved in this inter-action with a view to finding out more about the condition existing imme-diately at the surface of a crystal like a heavy metal sulfide after treatment with an organic reagent. Past experimental experience showed that finely ground galena shaken with aqueous potassium xanthate abstracts xanthate ion and at the same time sulfate ion, reducing ions of the type (SmOn)= where the ratio of m to n is less than 4:1 (as in sulfate), sometimes hydroxyl ion are thrown into solution.,

Jan 1, 1933

By George F. Weaton

Mining differs from the ordinary industry in that most industries and enterprises have an indeterminate life, apparently perpetual, and therefore, are not called on to replace the original investment. In mining, however, when the ore bodies are mined out, there is nothing left, The original capital investment must, therefore, be returned to the investor by the time that the profitable life of the mine is ended. When the operating company makes no provisions for perpetuating its life by investing a portion of its earnings in other properties, the usual procedure is to pay the investor, periodically, a dividend sufficiently larger than the risk return on his investment to enable him, if he reinvests this overplus at a safe rate of compound interest, to replace his original capital by the time the mine is exhausted. This overplus constitutes a return of invested capital. In estimating the value of a mining enterprise, the work leading to the final result may be divided into two parts. The first is the examination of the property to determine ore reserves, mining costs and profits, financial requirements and future prospects. Whatever conclusions are reached in this phase of the work depend on the experience, thoroughness and integrity of the examining engineers. The second is the calculations pursuant to the field examination.

Jan 5, 1973

By Howland Bancroft

This article is not presented as a treatise on tin mines and mining in Bolivia. It deals primarily with the tin situation, and but fragmentary information is given regarding individual properties, generalizations being necessary in so short an article. Data on general subjects related to tin mining in Bolivia are necessarily abbreviated and very incomplete. It is believed that the references to be found in this article will help those interested to a more thorough understanding of the general conditions extant in Bolivia. Bolivia produces from one-fifth to one-fourth of the world's supply of tin. The United States consumes about one-half of the world's supply and produces practically none. Tin ore is not reduced in the United States. These facts are not generally appreciated by American mining men. Many conflicting data have been published regarding tin in Bolivia. The Transactions of the Institute contain practically no mention of this subject.' I have made a study of mines and mining conditions in the west coast republics of South America and have been particularly impressed by the possibilities of the Bolivian field.= In consequence the thought seems justified that the present meeting would present a fitting occasion to bring the tin situation in Bolivia to the attention of American mining men.

Jan 1, 1914

By J. R. Dawson, J. A. Glunt

Vesta No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's by-product coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War II, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out.

Dec 1, 1956

By C. M. Marquardt

The minerals industry in general should bow in homage to the uranium milling industry. Those in the uranium milling industry have "spark- plugged" more progress in the application of instrumentation and control in the last 5 years than has been made in 50 years by the industry in general. Part of this real progress in the application of instrumentation and control has been born of necessity because milling processes are more complex. A lot of the impetus for instrumentation and control has come from the fact that the industry is new, the processes are new, and there are no hide-bound conventions to overcome. Part of it comes from the fact that much of processing is more chemical than metallurgical and the thinking of the process chemist has carried over into the plants. One need not elaborate on what instrumentation has done for the process chemical industries. Each new mill that is constructed, if of appreciable size, seems to employ more instrumentation than the previously completed plant. Plant A makes a break-through in the application of instrumentation to a particular part of the process and Plant B accepts this and goes one step farther, while Plant C, anticipating Plant B, makes two or three more steps before Plant B is entirely leveled out.

Jan 9, 1958

By A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except .conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

By B. Amero, W. Petruk, D. R. Owens, D. R. Morris

Samples taken at different heights in the lead blast furnace of Brunswick Mining and Smelting corporation were studied to determine the phases present in order to interpret the reactions In the furnace. The main phases in the blast furnace feed are Pb3Ca2S13011, Zn ferrite (ZnFe204), and hardystonite (Ca2ZnSi207); rninor ones include lead and a Pb silicate. The temperature in the furnace varies from about 300°C at 4.2 m above the tuyeres to 1150°C at 1.1 m. There is no evidence of reactions in samples from points cooler than 800°C. Some reaction occurs between 950° and llOO°C and the lead sinter is nearly decomposed at about 1150°C. The first evidence of reaction was the decomposition of Pb silicate to lead and S102. At higher temperatures the Pb Ca2Si3011 decomposed to form lead and hardystonite (Ca2ZnS120rf. The Zn required for hardystonite was derived from the Zn ferrite which apparently re-equilibrated to a new Zn ferrite with less Zn. The decomposed sinter consists essentially of lead, hardystonite, wustite and a Zn ferrite with a low Zn content.

Jan 1, 1984

By W. Evans, C. E. Ells

The agglomeration of hydrogen in pure aluminum and A1-Mg alloys has been studied through use of hydrogen introduced into the metal by cyclotron proton irradiation. Both the growth and dispersal of the agglomerates have been followed by metal-lographic techniques. During the cyclotron irradiation, agglomeration occurs at temperatures i 100°C for hydrogen concentrations as low as 1 ppm. On heating at elevated temperatures, 300°C to 600°C, intragranular agglomerates first coarsen and then disperse. The agglomerates formed at grain boundaries are much larger than the intragranular agglomerates; with hydrogen concentra- tions > 10 PPm, heating for 1 hr at 500°C results in extensive grain-boundary cracking. The hydrogen agglomerates have been shown to inhibit grain growth, but no inhibition of recrystallization has been observed. The ability of hydrogen to enter aluminum at a free surface, combined with its high-diffusion rate at elevated temperatures, accounts both for growth and dispersal of the agglomerates. Irradiations at elevated temperatures give results consistent with the explanation proposed for agglomerate behavior on post-irradiation heating. 1 HE formation of hydrogen-filled bubbles, or blisters. in aluminum and its alloys has been studied for over' thirty years. The work up to 1952 has been reviewed by Kostron' and since then Ransley and

Jan 1, 1963

By Howland Bancroft

This article is not presented as a treatise on tin mines and mining in Bolivia. It deals primarily with the tin situation, and but fragmentary information is given regarding individual properties, generalizations being necessary in so short an article. Data on general subjects related to tin mining in Bolivia are necessarily abbreviated and very incomplete. It is believed that the references to be found in this article will help those interested to a more thorough under-' standing of the general conditions extant in Bolivia. Bolivia produces from one-fifth to one-fourth of the world's supply of tin. The United States consumes about one-half of the world's supply and produces practically none. Tin ore is not reduced in the United States. These facts are not generally appreciated by American mining men. Many conflicting data have been published regarding tin in Bolivia. The Transactions of the Institute contain practically no mention of this subject.1 I have made a study of mines and mining conditions in the west coast republics of South America and have been particularly impressed by the possibilities of the Bolivian field.2 In consequence the thought seems justified that the present meeting would, present a fitting occasion to bring the tin situation in Bolivia to the attention of American mining men.

Jan 9, 1913

By Shigeki Nishimura

INTRODUCTION In this gapes, the author will describes to development of Yubari New coal mine. The construction set about since October 1970, and commenced from June 1975 in winning. Especially, descrives to compare with the studies at planning stage, and the experiences at under construction. The problems for development are next four: 1) There were no outcrop of the coal bearing strata, but the development was instituted against the deep coal seam occurrence at 800 m below the surface. 2) In order to the coal seams occured the deep level from the surface, threr had very difficult problems, i.e. temperature, earth pressure, methane etc. The countermeasure to solved them, were foundation of the development. 3) The construction was afflict with the inundation in high pressure, due to cement grouting and excavating alternately, overcame the difficulties. 4) The construction was finished by the encourage of national investment, in spite of the enterprise was weaken constitution from the energy revolution since 1960's. OUT LINE OF YUBARI NEW COAL MINE Geography Situation. Ishikari coal field is situated the west side of the Hidaka mountains, where runs north to south at center of Hokkaido, northern district of Japan. It's width is 40km in east and west, and length is 110km in north and south.

Jan 1, 1976

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

By Theodore Simons

The rapid and comparatively recent development of flotation has opened so fascinating a field for study and research that the older processes of gravity concentration no longer receive the attention they deserve. The early work of Munroel and Richards12 and the more recent contributions by Clevenger and Coe,3 Laist and Wiggin,4 Ammon,5 Bardwell,6 Crowfoot,' and Hayden8 (to mention only some which have appeared in our own Transactions) and by Schu1z,9 have furnished so much data that to offer something new seems a difficult task. It is still possible, however, to present known facts from a different point of view, and, with this in mind, the writer has undertaken to express basic principles of gravity concentration in terms of simple mathematics and mechanics; the conclusions thus reached will be found to correspond, in general, with those obtained by experimental methods. Rittinger, in his classic Aufbereitungskunde (1867)) reached analogous conclusions by way of intricate higher mathematics, for which reason his interesting investigations have remained a sealed book to most of us. The writer hopes that a more elementary treatment of the subject, based in part on Rittinger's metheds, may arouse new interest in the study of basic principles.

Jan 1, 1923

By I. N. Zavarine

The observations presented in this paper were recorded during a study of the spheroidizing process. Spheroidization of cementite in steel is either brought about to develop a set of desirable mechanical properties or is an incidental result of mechanical and heat-treating manipulations. Physical properties of steel are materially influenced by the state of the cementite. Conversion of cementite from the lamellar to the spheroidal state is usually accompanied by a decrease of hardness and of strength and by an increase in ductility. The spheroidized structure is usually considered as an ultimate step in the process of the softening of steel. The unorthodox hardening of a 3.5 per cent Ni steel (SAE No. 2330) after a heat-treatment that previously proved entirely suitable for a complete spheroidization of cementite in carbon steels led to the observations that constitute the subject of the present paper. Experimental Procedure The steels used for the experiments described were bought on the market. All were in the form of 3/4-in. round bars. Their chemical compositions are given in Table 1. The spheroidization of cementite in steels can be obtained in several ways. The method used in the present work is, perhaps, the least known. It consists of cyclic heating and cooling of steel, the temperature being

Jan 1, 1939

By I. N. Zavarine

The observations presented in this paper were recorded during a study of the spheroidizing process. Spheroidization of cementite in steel is either brought about to develop a set of desirable mechanical properties or is an incidental result of mechanical and heat-treating manipulations. Physical properties of steel are materially influenced by the state of the cementite. Conversion of cementite from the lamellar to the spheroidal state is usually accompanied by a decrease of hardness and of strength and by an increase in ductility. The spheroidized structure is usually considered as an ultimate step in the process of the softening of steel. The unorthodox hardening of a 3.5 per cent Ni steel (SAE No. 2330) after a heat-treatment that previously proved entirely suitable for a complete spheroidization of cementite in carbon steels led to the observations that constitute the subject of the present paper. Experimental Procedure The steels used for the experiments described were bought on the market. All were in the form of 3/4-in. round bars. Their chemical compositions are given in Table 1. The spheroidization of cementite in steels can be obtained in several ways. The method used in the present work is, perhaps, the least known. It consists of cyclic heating and cooling of steel, the temperature being

Jan 1, 1939

By Richard A. Busch, Roy L. Soderberg

Large, high, open stopes resulting from vertical crater retreat (VCR) and similar methods are usually filled with sand tailings to support the stope walls and make it possible to mine the pillars. The hydrostatic head resulting from these high stope fills demands extremely heavy bulkheads in the crosscuts to withstand the pres- sure. Occasionally, these bulkheads fail because there are no drains or the installed drains are inadequate. Costly flooding of the mine and loss of life result from these failures. With proper design of blanket drains and filters, the fill can be made failure-proof, requiring only a minimum bulkhead, designed specifically for zero water retention. The effectiveness of the blanket drains can be increased by laying perforated pipes on the bottom of the crosscut within the blanket drain. These drains can have a safety factor of 10 with minimal expense. When the water is properly drained, the hydrostatic pressure on the bulkhead is reduced to zero, leaving only the lateral pressure of the sand. This lateral pressure is partially dissipated by arching and shear against the crosscut walls and consolidation of the tailings as the water is drained. The bulkhead should be placed at least one cross-cut diameter back from the collar of the drawpoint.

Jan 1, 1983

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 lb. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War II. A prospecting program disclosed reserves of over 25 million tons of graphitic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses.

Jan 1, 1945

By E. S. Grumell

THE correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbrevia-tions will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution.

Jan 1, 1939

By Theodore Simons

The rapid and comparatively recent development of flotation has opened so fascinating a field for study and research that the older processes of gravity concentration no longer receive the attention they deserve. The early work of Munroel and Richards12 and the more recent contributions by Clevenger and Coe,3 Laist and Wiggin,4 Ammon,5 Bardwell,6 Crowfoot,' and Hayden8 (to mention only some which have appeared in our own Transactions) and by Schu1z,9 have furnished so much data that to offer something new seems a difficult task. It is still possible, however, to present known facts from a different point of view, and, with this in mind, the writer has undertaken to express basic principles of gravity concentration in terms of simple mathematics and mechanics; the conclusions thus reached will be found to correspond, in general, with those obtained by experimental methods. Rittinger, in his classic Aufbereitungskunde (1867)) reached analogous conclusions by way of intricate higher mathematics, for which reason his interesting investigations have remained a sealed book to most of us. The writer hopes that a more elementary treatment of the subject, based in part on Rittinger's metheds, may arouse new interest in the study of basic principles.

Jan 1, 1923

By W. E. Pugh

The object of the following is to discuss a few of the problems encountered in the practical field application of reflection seismology. Very little has been published on this phase of the work and it is to be hoped that discussions will be presented by many seismologists who have met with these problems in the field. No attempt will be made to discuss the general principles of reflection prospecting, nor to outline the general field procedure. These phases have been presented more or less in detail in previous publications1 while economy of space and time prevents their being repeated or amended here. If, in the following pages, some criticism is offered of those who have already given their time and efforts to present valuable papers on reflection shooting, we trust that it will be accepted in the constructive light under which it is offered. We do not wish to give the impression that the following paragraphs represent ultimate achievement in field procedure; they are presented more to illustrate methods we have found satisfactory thus far. We believe that the following three subjects are inexorably linked with the continued future successes and more widespread use of the reflection method which, at the present time, is the most

Jan 1, 1934