Search Documents

By Roy C. Bartholomae, Jeffrey Shawn Peterson

1. INTRODUCTION In the early 1980s, the U.S. Department of the Interior’s Bureau of Mines Pittsburgh Research Center required that a large reverberation acoustic facility be constructed. This facility was designed to determine the sound power level emissions of mining equipment, especially continuous miners and jumbo drills. A contract for a conceptual design of a reverberation chamber was awarded to Wyle Laboratories of Huntsville, AL, which had extensive experience in the design, construction, and accreditation of acoustical reverberation chambers. The following standards were referenced as guidelines for the design of the chamber: ANSI S1.31-1980, “Precision Methods for the Determination of Sound Power Levels of Broadband Noise Sources in Reverberation Rooms” and ANSI S1.32-1980: “Precision Methods for the Determination of Sound Power Levels of Discrete-Frequency and Narrowband Noise Sources in Reverberation Rooms.” Specific requested criteria included that the room be large enough to accommodate typically large mining equipment and that there be adequate acoustical modal density in the frequency range of interest. It was also required that the room dimensions would support broadband acoustical measurements down to the 100 Hz third octave band. With the closing of the Bureau of Mines in 1996, this reverberation chamber lay dormant for a number of years. However, this facility is now part of the National Institute for Occupational Safety and Health’s (NIOSH’s) Pittsburgh Research Laboratory (PRL). One of NIOSH’s missions is to decrease noise induced hearing loss among the nation’s mineworkers. To this end, PRL researchers are refurbishing and instrumenting this reverberation chamber to facilitate assessment of the various engineering controls being developed to decrease the sound power level emissions of mining equipment. Early on, this work has sought to bring the chamber up to the level of ISO 3743-21 standard for engineering grade measurements for broad-band noise, with a longer range goal of improving the lab to meet the requirements of ISO 37412standard for broadband precision grade measurements. 2. DESIGN OF THE REVERBERATION CHAMBER The nominal room dimensions are 18.3 meters long by 10.3 meters wide with a height of 6.7 meters. The chamber volume is 1,286 cubic meters. These dimensions are important, as few reverberation facilities are large enough to test typically huge mining equipment. The floor is poured concrete with a sealer to make it acoustically reflective. The walls are built of hollow concrete block, 16 inches long x 8 inches high by 12inches thick. Each block has two hollow cores. The hollow block cores were completely filled with concrete with horizontal and vertical steel reinforcing bars 16 inches on center. This was done to supply a

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By T. J. Lynch

A new class of polymeric dispersants for industrial minerals has been synthesized and evaluated. Currently available dispersants give initial low viscosities at high mineral loadings, however slurry viscosities can rapidly double or triple on standing over the first several days. The new dispersants give low initial viscosities that are more stable and maintain a lower viscosity for at least one month. The new dispersants are made possible by controlling the polymer molecular weight distributions during their manufacture such that essentially all of the dispersant is adsorbed onto the mineral surface, preventing depletion flocculation.

Jan 1, 2012

By D Skinner, P Haeussler, D Bradley, A Christie

Mesothermal gold deposits of southernAlaska and Westland, New Zealand have both formed at the seaward edge of major collisional zones in the Pacific basin. In Alaska, production of large fluid volumes correlates in time with the addition of heat into the lower parts of the accreted terranes in the late stages of collisional orogeny. This heat was critical for driving both the metamorphic reactions that released the large volumes of fluid that carried the gold, and the contemporaneous widespread anatexis and magmatism. In Alaska's Chugach terrane, this heat as produced by subduction of a spreading ridge beneath the North America continental margin in the Eocene. The resulting products were the S-type granites and gold-bearing veins. The similar widespread S-type plutonism and gold veining in Westland's Buller terrane suggest that a similar tectonic event could have triggered ore formation along the southeastern edge of Gondwanaland. Based on the Alaskan model, a Devonian or Early Carboniferous age is favoured for high volume metamorphogenic fluid generation and gold vein formation in Westland.

Jan 1, 1995

By Gartrell H. W

During investigations of the treatment methods for ore from the Bird-in-Hand gold mine carried out at Kalgoorlie and at these laboratories, it was found that excess alkali caused a lowering of extraction by cyanide, the cause of this being attrIbuted to the presence of a small amount of oxidised lead compounds in the ore. The subject has been discussed by various writers,3 but no satisfactory explanation of existing facts has been put forward. The experiments described in this report have been carried out with the object of obtaining some insight into the chemical reactions underlying the effect of lead salts and alkalis in cyanidation.The formation of cyanide-insoluble coatings on gold during roasting with lead compounds is well known, but the adverse effect of alkalis in cyanidation of ore is *This paper represents work done under a co-operative agreement between the Commonwealth Council for Scientific and Industrial Research and the South Australian School of Mines and Industries.Published by permission of the Mining Advisory Committee, Commonwealth Council for Scientific and Industrial Research.

Jan 1, 1935

By Bruce Gellar

For the past six years, the author has made it a priority to attend the Prospectors and Developers Association of Canada’s (PDAC) annual conference. This most recent meeting took place March 10-13, 2002in Toronto, Ontario. In the three years since the author’s last PDAC report, the mining industry has undergone a severe trough. Some the industry’s woes included deeply discounted commodity prices, rampant layoffs, mergers, and overall avoidance by the investment community. However, at each of the PDAC conferences, the author has felt a heightened sense of excitement about the mining industry, more so than at other similar gatherings.

Jan 1, 2002

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

By J. Janssens, B. Coletti, S. Smets, J. Plessers

The oxygen activity of the ladle slag determines the reactivity towards the steel during ladle treatment. Therefore, the in situ measurement of the oxygen activity of slags can be an important tool. The applicability of an electrochemical sensor is examined in this work. The sensor measures the electromotive force (EMF) that is established between a sample of the slag phase that is immersed in the liquid steel bath and a reference system (Cr/Cr2O3). Industrial and laboratory experiments demonstrated the capability of the sensor to detect the influence of the slag components on the measured oxygen potential. Comparison of the measured values with thermodynamically calculated values shows that the measured oxygen activity is systematically too low. This was attributed to a reaction of the steel with the slag sample. To investigate this, further lab tests were performed where the slag oxygen activity was measured after the slag had been equilibrated with the steel. The measured values were dependent on the oxygen activity (aO) of the steel. For industrial applications, it is concluded that the aO of the steel should be known and that this value is necessary for the interpretation of the measured values. Keywords: low carbon steels slags, slag oxygen activity, on-line sensing, thermodynamic evaluation.

Jan 1, 2004

The common theme of these four objectives is declaration. Declaration tells the compiler that an entity exists and also provides the name and nature of the entity. Since everything you create has to be declared, you must know how to declare correctly and be able to make appropriate use of all the declaration tools available to you. This objective recognizes the importance of declaration by requiring you to know everything about Java declarations Write code that declares, constructs, and initializes arrays of any base type using any of the permitted forms both for declaration and for initialization. This objective addresses your understanding of all aspects of arrays. Arrays are the simplest possible data collection and are supported by all modern programming languages. However, Java?s arrays are different from those in other languages, especially C and C++, because they are actually exotic objects. This objective recognizes the importance of being able to make use of all the functionality of arrays. You will be expected to know how to declare, construct, and initialize arrays.

May 1, 2011

By M I. Pownceby, S Hapugoda, V Nunna

Deposits of low-grade iron ores containing abundant goethite are distributed across the world. A common difficulty associated with beneficiating goethitic-rich ores is the poor liberation characteristics of the iron-bearing minerals which often contain finely disseminated gangue minerals such as kaolinite, gibbsite and quartz. Microwave-assisted heating has been proposed as an effective way of inducing dehydroxylation and associated mineral transformations in order to beneficiate low-grade goethitic ores. In this research, the mineral transformations occurring in a low-grade goethite-rich sample using microwave radiation was studied. Roasting conditions (up to 1000°C and under various CO/CO2 gas atmospheres) were designed to generate a magnetic product from a goethite-rich, reject waste stream sample sourced from an iron ore processing site in the Pilbara, Western Australia. Conditions (T, pO2) for transforming the raw material from hydrated goethite to hematite and eventually to magnetite are presented. Chemical and mineralogical characterisation of the raw material and roast products were conducted using X-ray fluorescence, X-ray diffraction, optical microscopy and scanning electron microscopy techniques to identify the mineralogical and chemical changes occurring during the heat treatment. Further steps are suggested to optimise the microwave-assisted magnetising roasting and correlate it with the application of magnetic separation techniques to maximise the efficiency of upgrading the iron content in low-grade iron ores.CITATION:Nunna, V, Hapugoda, S and Pownceby, M I, 2017. Study of microwave-assisted magnetising roasting and mineral transformation of low-grade goethite iron ores, in Proceedings Iron Ore 2017, pp 575–582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

An oxide ore heap (80,000 ton assaying 2 per cent copper) and a sulphide ore heap (300,000 ton assaying 1·7 per cent copper) are being leached in series in a closed circuit system. The ore is friable and weatherseasily giving severe percolation problems. These were eased by applying liquors at 235 gal/min to trenches 2 ft wide and 6 ft deep along the full length of the heaps.Cementation recovery was improved from 20 per cent to over 80 per cent by regular intermittent agitation of the iron using a back hoe unit.Liquor pH is controlled by acid addition, and iron content is controlled by a bleed-off set according to predictions made from a pH-Eh diagram drawn for the liquor components. These controls, together with acyclic wetting and draining procedure, have raised production from 6 ton/week to 10 tdn/week of 80 per cent copper.

Jan 1, 1968

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

By Dechun Lou, Benjamin Ravary, Merete Tangstad, Stein Wasbø, Sean Gaal

The melting phenomena of manganese ore, slag and alloys were studied in an experimental sessile drop furnace. Particles of approximately 20-60mg were placed on graphite substrates and then heated at a constant rate of 5°C/min up to 1830°C in a controlled gas atmosphere of Ar or CO. The shape of the particle was photographed with a digital video camera every second. It was observed that the melting behaviour can vary significantly, with some particles exhibiting a large softening/melting range. Selected samples were sectioned and then analysed with EPMA. The implications of the results on understanding industrial furnace operations are discussed.

Jan 1, 2007

By Tjaar A. Louw, Albert P. Van Niekerk, Johannes J. Louw, Attie J. Goosen

Unlike molecular high explosives, commercial explosives based on ammonium nitrate do not detonate ideally according to the theoretical model for steady state, one-dimensional detonation. One of the reasons for this deviation from ideal detonation is the slower chemical reaction, due to less intimate contact between the oxidiser and fuel components. It is well known that the inclusion of gas pockets, such as microballoons, in the formulation of ammonium nitrate based emulsions and watergels enhances the performance of these explosives. Various different interpretations of the “hot spot” theory have been proposed to explain this phenomenon.

Jan 1, 1997

By Wilfred P. Schmoe

Introduction An integrated oil company has two options in approaching strategic planning. It has to decide whether it is in business for the long-term. I state this in all seriousness. Those who help manage public companies have the responsibility of good stewardship of other people's money. We must decide whether continued investment in our basic business will generate a reasonable rate of return. With a world surplus of petroleum production capacity, and continuing downward pressure on prices, this question should be addressed by all oil companies. And a positive answer is not necessarily a foregone conclusion in all cases. The decision should be made based on proven competence in finding and developing petroleum reserves on a cost-competitive basis with other producers, and on a frank analysis of future prospects. This should include a realistic assessment of the projected rate of return on specific investment projects. If a company did not pass these tests, its strategy could take one of four paths. Diversification First, it could diversify. But recent history suggests that oil companies are not good at managing other businesses. Second, it could seek a buyer for its business at the optimum return for its owners. Third, it could sell its assets on a piecemeal basis. And, fourth, it could adopt a longer-range plan of self-liquidation by living off current recoverable reserves. In other words, by not investing in exploration and development, it could maximize short-term profit and pass the money back to shareholders in the form of dividends. The Conoco component of DuPont has a below-average cost of finding petroleum, a good track record of efficient production, and a full plate of projects that pass the test of return-on-investment. In short, Conoco is in business for the long-term. That fact, in itself, determines at least one key element in strategy. This is to extend the life of the petroleum reserve base while at the same time maintaining maximum efficient rates of production to provide a strong cash flow. A company that is able to maintain a strong reserve base will ultimately see the value of those reserves escalate as world oil supplies tighten. Our planners expect this tightening to occur within the next decade as demand grows and production in non-OPEC areas of the world begins to decline. An exploration program tailored to meet the requirements of reserve replacement and current production should have two basic parts. The first is relatively low-risk exploration in proven oil provinces. This is augmented by

Jan 6, 1985

By R. L. Virta

Four companies ? H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. ? mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.

By M. Arlandi, J. C. Monge

In this paper, the finite element method is used to obtain deformations of a rock tunnel. More than 3,000 numerical simulations and calculations were carried out. The analysis of this results has allowed to achieve mathematical formulations and graphs, to obtain in advance support monitored displacements in tunnelling construction, so they can be predicted before excavation and supporting woks. The application of the presented formulations and charts will aid engineers to control tunnel monitoring, reducing decision time when problems occur. The analysis is limited to cases involving elastic behaviour of the terrain for tunnels of average to good quality in rock, and to excavation sections of average or smaller dimensions for road tunnels. The results show that, in all cases, mathematical expressions to obtain induced displacements around tunnel excavations, have similar pattern than Kirsch (1898) expressions for circular excavations. As corollary of the achieved results, a method to estimate in situ natural geostress ratio K0=sh/sv , by means of convergence measurements, is presented. In diesem Beitrag wurden die Verschiebungen eines Tunnels durch die Methode de Finiten Elemente berechnet. Mehr als 3000 numerische Simulationen und Berechnungen wurden ausgeführt. Die Analyse dieser Resultate hat es ermöglicht, mathematische Formeln und Grafiken zu entwickeln, die zur Voraussage der Verschiebungen in Tunnel dienen, auch unter Betrachtung der verschiedenartigen Abstützungen. So können die Verschiebungen vor den Erdarbeiten und dem Bau der Abstützung abgeschätzt werden. Die abgeleiteten Formeln und Grafiken werden vor allem einen grossen Dienst für Ingenieure bei der Mithilfe zu zeitsparenden Entscheidungen im Tunnelbau und bei der Tunnelkontrolle leisten. Die analysierten Fälle sind auf eine elastische Modellierung des Baugrunds beschränkt, sowie auf eine mittlere bis gute Qualität des Felsens und auf die Aushebung von Abtragungsabschnitten mittlerer oder geringer Grösse für den Strassenverkehr. Die Resultate zeigen, dass in allen Fällen die hergeleiteten Formeln zur Berechnung der durch den Tunnelbau verursachten Verschiebungen um den Tunnel die gleiche mathematische Struktur haben wie diejenigen von Kirsch (1898) für kreisförmigen Bodenaushub. Als Korollarium der ausgeführten Berechnungen wird eine Methode zur Abschätzung der vorherrschenden in situ Geospannungs-Verhälniss K0=sh/sv angegeben, die von den Messungen der Verschiebungen im Tunnel ausgeht. Dans cet article, la méthode des éléments finis est utilisée pour obtenir les déformations d’un tunnel creusé dans la roche. Plus de 3000 simulations numériques et calculs ont été effectuées. L’analyse de ces résultats a permis de définir des modèles mathématiques et des abaques afin de prédire, avant l’excavation et les travaux de soutènement, les déplacements auscultés pendant la construction du tunnel. L’application de ces modèles et abaques permettra donc aux ingénieurs de contrôler les déplacements durant l’auscultation du tunnel et de réduire le temps de décision lorsque des problèmes surviennent. L’analyse est limitée au cas du comportement élastique du terrain pour des tunnels creusés dans de la roche de moyenne a bonne qualité, et à de sections d’excavation de petites à moyennes dimensions pour des tunnels routiers. Les résultats montrent que, dans tous les cas, les expressions mathématiques permettant d’obtenir les déplacements induits autour des excavations de tunnel, présentent des similitudes avec celles de Kirsch (1898) pour des excavations circulaires. Comme corollaire aux résultats obtenus, une méthode pour estimer le rapport des

Jan 1, 2003

By William R. Yernberg

The current state of the copper industry was the topic of discussion at the Copper 99 — Cobre 99conference held Oct. 10 to 13, 1999, in Phoenix, AZ. More than 700 copper-industry engineers, executives, consultants, academics, vendors and other interested parties attended. This successful and well-organized conference was the fourth in a series of international conferences devoted to the mineral processing and extractive metallurgy of copper. The 1999 meeting marked the first time that the conference was held in the United States. The meeting was co-organized by the Minerals, Metals and Materials Society (TMS); the Chilean Institute of Mining Engineers (IIMCH) and the Metallurgical Society of the Canadian Institute of Mining, Metallurgy & Petroleum(CIM). The meeting was also sponsored by The Society for Mining, Metallurgy and Exploration Inc.

Jan 1, 2000

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By C. Velásquez, W. Bergholz, C. Spence, P. Lind

NuevaUnión SpA (NuevaUnión) is a development project located in the Huasco province of the Atacama region of Chile. It is held in a joint venture company owned 50:50 by Teck Resources Limited (Teck) and Newmont Goldcorp. It includes the Cu-Mo Relincho deposit and the Cu-Au La Fortuna deposit, with plans to utilise a single concentrator to be built at the Relincho site. The Relincho site is at an altitude of 2,000 masl and is 40 km from the La Fortuna site which is at an altitude of 4,100 masl. The project is currently completing a Feasibility Study and is reviewing equipment selection and flowsheet options. This paper is based on the current thinking, and design decisions will be finalized at the completion of the Feasibility Study. NuevaUnión is currently planning for phased operation, processing Relincho ore at 104 ktpd followed by processing ore from La Fortuna at 116 ktpd. Plans for the third phase include doubling the main processing lines and returning to Relincho ore at a processing rate of 208 ktpd. The NuevaUnión concentrator will incorporate comminution and flotation circuits that are being designed to maximize the overall economic value of the combined ore deposits. Major ore characteristics differ between the two ore bodies, such as ore competency, grindability, liberation grind size, pulp rheology, tailings properties, minerals and metals of value, as well as gangue mineralogy. Mineral processing choices have been made to optimise value from each deposit and the combined project. INTRODUCTION Between 2010 and 2013, two significant mining projects were being developed in Chile: Goldcorp’s El Morro project had recently finalized a Feasibility Study and, in 2011, had received its environmental approval for construction; and Teck Resources Limited’s (Teck) Relincho project was finalizing a Feasibility Study and preparing its Environmental Impact Study. Both projects were: Geographically close, at only 40 km apart. Considering similar infrastructure. Each was planning to have its own concentrator, tailings management facility, high voltage power line, port, concentrate transport system, seawater desalination plant and pumping system to mine site.

Jan 1, 2019