Search Documents

By Breen AM, Phelan JM, Doherty RJ

Early in 1990, Pancontinental Resources (Base Metals) Pty Ltd commenced flotation treatment of ore from the complex copper-lead-zinc sulphide orebody at Thalanga, 65 km west of Charters Towers in North Queensland. The orebody consists mainly of primary sulphide ore but also contains a substantial proportion of supergene ores which are being processed during the first year of operations. The supergene ores are of three main types, designated as A, B, and C. Supergene A ores are essentially copper ores, containing little lead and zinc, while B and C ores are copper-lead-zinc ores with different degrees of alteration of the original chalcopyrite and different ratios of copper to zinc content. Copper is present in the supergene ores mainly as chalcocite, digenite and covellite. Lead and zinc occur mainly as galena and sphalerite respectively. This paper describes the development of flotation plant practice, aided by laboratory testing, to process the supergene ores. The major challenge in treating these ores is that a varying proportion of the sphalerite is naturally activated and is not easily depressed in flotation by the conventional zinc depressants.

Jan 1, 1991

By John T. Bartlett

With more stringent environmental and economic constraints being placed on mining operations, it has become necessary to optimize each process to minimize energy and raw material consumption and reduce waste discharge. In most cases, detailed process analysis is required to detect inefficiencies and provide alternative solutions for process improvement. HETSIM, a microcomputer process modeling and simulation system, is routinely used to analyze communition, hydrometallurgical, pyrometallurgical, and coal preparation processes. The process modeling techniques used in METSIM, including process control simulation, will be presented and illustrated using actual plant processes.

Jan 1, 1987

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of drainhole drilling on production capacity. Drain holes are those lateral holes which are sometimes drilled to assist in increasing the oil drainage into the main wellbore. The studies indicate that if the drainhole length i.r near 0.2 of the drainage radius, the increase in production capacity may be approximately 1.8, 2.08, trnd 2.33 for the case of one, two and four drain holes, respectively. If multiple drain holes are drilled, shorter holes are required to achieve a specific increase in production capacity than if one or two holes are drilled. To achieve increases in production capacities by factors near three it is shown that the drainhole lengths divided by the drainage radii must be approximately 0.64, 0.48, cnd 0.37 for the case of one, two and four drain holes, respectively. IN T RO DUCTION Kecent developments in drilling techniques have permitted the drilling of lateral or horizontal holes to increase the rate of production. The number of these drain holes may vary from 1 to 10, and they have been drilled laterally as much as 100 ft. Drainhole drilling at substantial depths is of recent origin but has been used in the Spraberry field of West Texas, the La Pas field in Western Venezuela, and certain fields in California. The diameter of the drain holes has been approximately 6 in. In drilling drain holes it is desired to know how much increase in production capacity may be expected, what additional benefit may be gained by drilling more than one drain hole, and what increase in production capacity may be brought about by lengthening the existing drain holes. In realization of the importance of lateral drilling, electrical model studies were made to provide quantitative estimates on the effect of drain holes on production capacity. ANALYSIS An electrical model was used in studying this problem. A wooden circular reservoir approximately 30 in. in diameter and 2 in. deep was filled with a dilute salt solution to a depth of 1 in. A copper band formed the periphery of the tank, and a copper wire was inserted in the center of the tank to represent the well. The drainage radius divided by the well radius was equal to 500. A diagram of this type model is shown in the inset of Fig. 1. An electrical potential was applied to the wire well and copper band at the periphery to determine the flow of current. Following this measurement copper wires of various length were soldered to the vertical wire well in such a manner as to simulate lateral wells drilled into the reservoir. Multiple lateral holes of various lengths were studied by varying the number and length of copper wires soldered to the vertical wire well. All multiple lateral wells were located symmetrically about the vertical well. The effect on production capacity by drilling an infinite number of lateral holes was studied by replacing the lateral hole with a copper disk. For each condition the flow of current was measured and compared with the flow of the vertical well only. The model which is thus described provides the steady state increases in production capacity which may be expected in some cases. The data conform to those which would be observed for a uniform homogeneous reservoir. The data may have primary application to those reservoirs producing above the bubble point. It is realized that few lateral holes are drilled in reservoirs of this type, but the data may be of some value in guiding future work or aiding to explain observed phenomena.

Jan 1, 1956

By A. J. Griest, P. D. Frost, J. R. Doig

During the past 5 years, research directed toward the development of titanium alloys having improved strength-ductility relationships and heat treatability has been carried out at Battelle for the U. S. Air Force.1"3 In the course of this work, a method of heat treating ß-stabilized titanium alloys was developed which produced a wide range of useful properties.4 The heat treatment consisted of two steps: a) solution treating at temperatures in the a-ß phase region, and b) overaging at a lower temperature in the range 800°to 1100°F. Corollary to the alloy development work, research was conducted on the mechanism of the heat-treatment reaction. The investigations of Frost and co-workers on isothermal transformation in Ti-Cr5 and Ti-Mn8 alloys disclosed the existence of the transition phase, w, during the course of the decomposition of metastable ß phase. Subsequent work at Battelle7,8 'and at Case Institute by Brotzen and co-workerss further clarified the nature of the decomposition process. Beta decomposition was found to proceed by the following series of reactions: 1 2 3 4 a + Ti, My (in eutectoid systems). ßo, ßr, and ßU refer to ß phase of original, enriched, and ultimate alloy contents, respectively. Omega is a transition phase having a complex structure. 10-13 Step 4, of course, occurs only in ß-eutectoid systems. This paper presents data correlating transformation behavior with mechanical properties for the following alloys: Ti-8Mn, Ti-8Mn-2A1, Ti-4Mn-4A1, Ti-6Al-4V, and Ti-4Fe. The isothermal decomposition of ß in titanium-manganese alloys of similar composition has been investigated by Frost and coworkers8 and the effect of various annealing treatments on alloys in this system has been studied by Holden, Ogden, and Jaffee.14 The compositions Ti-8Mn-2Al, Ti-4Mn-4A1, and Ti-6A1-4V, were studied in the present work in an effort to define more clearly the effect of aluminum on the response to solution and aging treatments. Ogden, Holden, and Jaffee15 have invesitgated the effect of aluminum on the response of a similar alloy (Ti-8.8Mn-2.46A1) to annealing treatments, and Luini and Lee16 have made an exploratory investigation of the heat-treatability of the Ti-4Mn-4Al alloy. The Ti-4Fe alloy was studied as an example of a moderate1y active eutectoid system. Holden, Ogden, and Jaffee 17 have studied Ti-Fe alloys and have presented some hardness data for aging at 400°C for alloys of Ti-2.56, 5.01, and 7.35 iron after quenching from the a-ß field (750°C). EXPERIMENTAL PROCEDURES The experimental procedures generally used in the precipitation-hardening study are outlined in the following sections. Departures from these techniques are noted in the discussions of the individual alloys. Table I presents the nominal and actual compositions of the alloys studied, together with the swaging and rolling temperatures. In all cases, these temperatures were in the a-ß field and the microstructures consisted of an equiaxed a-ß mixture. Melting and Fabrication—Except for the commer-

Jan 1, 1960

By Aaron Nickoli, Brad Clark, Thomas Horan E. I. T.

The Canal Road Dip Slide is an active landslide located on South Pender Island, British Columbia. The effects of the fall 2021 atmospheric river prompted the British Columbia Ministry of Transportation and Infrastructure to initiate an emergency response project to realign Canal Road out of the active landslide zone for safe traffic passage. The work was tendered in a bidding process and included blasting and rock excavation work at the project site. Tetra Tech Canada Inc. was retained by the contractor to be their Blast and Vibration Specialist. The close proximities of an active landslide, a Canadian National Park, and other segments of construction posed stringent constraints to blasting. The governing constraints to blast design included a Peak Particle Velocity (PPV) limit of 3 mm/s (0.12 in/s) along the adjacent landslide centerline and a slide movement constraint. Sixteen blasts were executed throughout the scope of work to remove 2595 m3 (3394 yd3) of meta-sedimentary rock. Blast designs adhered to the constraints by utilizing up to quadruple decking in 50+ blast holes which lead to complex timing schemes. Several blasts were over 4 seconds in duration, with one at nearly 8 seconds. The landslide area was monitored with Shape Accel Arrays (SAA) throughout the scope of work that tracked geohazard slide movement during construction. The SAA data is presented, and the effect of blasting is discussed. Site specific parameters for PPV estimation were calculated and are presented. Collaboration and communication between the stakeholders allowed the project team to successfully overcome the technical challenges posed by the Canal Road Dip Slide.

Jan 26, 2026

By M. T. Melvin, N. P. Kripakov

The practical application of a post-processing modeling procedure to simulate progressive rock failure around the periphery of coal mine entries is presented. This numerical scheme utilizes a simple rock model that incorporates easily obtainable input parameters consistent with basic rock mechanics principles. These parameters include the cohesion, angle of internal friction, modulus of elasticity, and Poisson's ratio of the bedded deposits that comprise the imediate roof, coal seam, and immediate floor. The geometry of the entry, along with the in situ stresses existing at a mine site prior to mining, are also considered in the analysis. The potential of this procedure as a predictive tool in determining the extent of pillar rib fracturing and yielding of the immediate roof and floor is evaluated assuming a Mohr- Coulomb failure criterion. The procedure is designed to be user oriented and is adaptable to any finite element code with linear elastic capability, making it particularly attractive to users with limited budgets and computer size.

Jan 1, 1983

By Oliver U. Bradley

The conditions affecting the supply of casinghead gas, the different degrees of productivity, the difficulty of determining the quantities utilized, and the evaluation of the gas in casinghead-gasoline units and related data, having an economic bearing on the industry as a whole, are important questions and offer an interesting field for study. Casinghead-gas data have been gathered in some of the oil fields of Oklahoma where testing work has been done regularly and the volumes of casinghead gas were available. The area covered embraces 219 scattered leases in 29 townships, with a total of 18,039 acres and 1921 wells. The accompanying table gives specific locations of the areas under consideration, number of leases, range depth of wells, average age of production, sand depths and oil production data. The results of this investigation are set forth in the accompanying charts, showing volumes of casinghead gas in 6-month periods from Jan. 1, 1918, to June 30, 1921, when full record was available, production of casinghead gasoline, average productivity of the gas in gallons per thousand cubic feet, average price of the gas and the market price of the casinghead gasoline. The cases enumerated in the table and the data shown in the graphs do not represent the greater part of oil or casinghead gas production from any one township, nor are the leases contiguous. The properties in each township, however, may be considered as typical of general conditions, such as the date of completion of wells, depth, character, and thickness of oil sand, time of pumping, present oil production, Vacuum carried on wells, and usual operating practices. It was deemed advisable to subdivide the time into 6-mo. periods, as it was impracticable to make the tests more frequently, furthermore 6 mo. is probably the minimum period within which there would occur a noticeable increase in the productivity of the gas. It must be remembered that the figures on volumes are subject to the usual irregularities and relative inaccuracies of meter measurenlents of gas under varying degrees

Jan 1, 1924

By Jed H. Mosgrove

Ventilation is the method of producing, conducting, and distributing a constant current of fresh air through mine workings and returning the impure air to the outside atmosphere. Without ventilation no operations are possible in an underground mine. Therefore it is the most important single phase of mining, one on which everything else depends. A good ventilation system, therefore, must be correctly designed, properly conducted as the workings advance, and continually checked to make sure it is functioning correctly. Good air is essential for men to comfortably and safely perform their work. It is also essential to dilute, render harmless, and sweep the mine of any explosive fumes and the gases that are released in varying degrees by all coal seams and the rock strata in which they are contained. GENERAL The body of air that is being moved through the mine, known as the ventilating current, must have a definite way to enter and leave the mine. In other words, there must be a definite intake and return. The main consideration is to get the proper amount of good quality air to the working faces where it is needed. Inasmuch as the mine is divided into sections with interconnecting corridors, known as entries, it is necessary that there be a proper means of conducting the air to the proper points. As a simple explanation of a mine, consider a long tube and think of it in terms of a mine entry ill which the air must pass. The tube must have at least two openings before air can travel through it and this is the same for coal mine entries. The problem in ventilation is to find some means that will cause the air in the tube to flow from one end to the other. The only possible way to do this is to cause greater pressure at one end of the tube than at the other. Air at the end with the greatest pressure would then, of course, flow to the en which has the least pressure. Mine

Jan 1, 1973

A novel pressure leaching process for platinum group metal (PGM) feedstocks is described. The process is particularly well suited for treatment of ores or concentrates that are too low grade for economic processing by the conventional smelting/leaching process. Operating conditions have been identified under which gold, the PGM's and the base metals dissolve simultaneously in a pressure leaching autoclave. The product of this leaching process can then be treated by one of several flowsheets, of which the preferred will likely involve solid/liquid separation, followed by precipitation (or adsorption on activated carbon) of gold and the PGM's, followed by copper solvent extraction/electrowinning. Depending on the concentrations of nickel and cobalt, the copper raffinate would either be partially recycled to the autoclave to allow NilCo concentrations to build up, or it would proceed directly to a Ni/Co refinery. This paper deals with the pressure leaching process and the recovery of gold and the PGM's from the pressure leach product.

Jan 1, 2000

By Leonard Obert

THIS REPORT presents methods and principles useful in designing underground mine openings and pillars in competent rock formations. Two types of formations are considered: (1) Massive formations, in which openings are generally mined with an arched roof, and (2) bedded formations, in which openings are generally mined with a flat roof. Design principles for openings and pillars in massive formations are obtained by considering the maximum tangential stresses developed around single and multiple openings for stress fields of various types. Design principles for openings and pillars in bedded formations are obtained by considering the average stress in pillars and the maximum stresses in roof layers. Experimental procedures for making stress, strain, and in situ physical-property measurements in underground mines to check design calculations are outlined and the results discussed.

Jan 1, 1960

By Christopher Haycocks

Subsidence induced innerburden shearing and stress fields, whether active or passive, frequently contribute to significant ground control failures in overlying seams. In this paper proven multi-seam technology is used on upper seams to forecast and quantify the magnitude and severity of damage and the increased mining risk due to interaction. Increased upper seam ground control problems are demonstrated using hazard mapping which provides a viable technique for utilizing damage predictions in design.

Jan 1, 1986

By J. J. Cummins

Green River oil shale previously extracted by benzene was heated at 150°, 200°, 250°, 300°, and 350° C for 0.5 to 360 days to determine the rate at which kerogen degrades to thermal products, the types of thermal products formed, and the effect of prolonged low-temperature heating (preheating) upon subsequent assay yields. Thermal decomposition of kerogen at 150° to 350° C is treated as a first-order reaction. The specific reaction rate for kerogen decomposition increases from 2.2 X 10-4 per day at 150° C to 2.0 X 10-1 per day at 350° C. The calculated kerogen activation energy is 19 kcal. Variations in the rate of formation of individual type components of the pyrolytic products were found. Carbon balances show an increase in the amount of kerogen converted to bitumen and oil (from assay of preheated oil shale) as the temperature of preheating increased from 150° to 350° C. Total product from shale preheated at temperatures of 150° and 200° C gave less than 100 percent of Fischer assay yields while the total products from shale preheated at temperatures of 250° to 350° C gave greater than 100 percent of Fischer assay yields.

Jan 1, 1972

By H. F. Easter

(San Francisco Meeting, September, 1915) THE lead department of the El Paso Smelting Works at El Paso, Tex., is operated strictly oil a custom basis. The ores treated are drawn from the surrounding territory, comprising New Mexico, Arizona, western Texas, and northern Mexico. Ores received from the last-named section originally amounted to a very large tonnage, but of recent years have dwindled into comparative insignificance so far as this plant is concerned. This has been clue partly to the establishment of a lead-smelting plant at Chihuahua, which is much closer than El Paso to most of the important mines, and partly to the recent revolutionary troubles in Mexico. There are no mines of either lead or copper in the immediate vicinity of El Paso. In general, it may be said that the lead-ore supply of recent years has been uncertain and precarious, with a general tendency toward an excess of silica and a shortage of iron. This latter requirement has been met in large part by the use in El Paso lead furnaces of considerable amounts of roasted heady copper matte from the Chihuahua smeltery and of converter slag from the El Paso converters. These two materials, coupled with complex lead-copper ores from Bisbee, Ariz., have introduced into the lead-smelting operations a most unusual amount of copper, which has had an important bearing upon the smelting practice of the plant. This matter will be discussed later. The ore, loaded in either box cars or gondolas, enters the storage yard on four tracks elevated about 8 ft. above the ground. As all unloading is clone by hand, unloading platforms at the height of the car floor parallel the tracks on each side to afford a runway for wheelbarrows. At frequent intervals these lengthwise platforms are joined together by others running crosswise to facilitate the distribution of the ores evenly over the beds, which are located below and between the tracks. At present much of the bedding space formerly used for lead ores is given over to the copper department, but 20 bins of various sizes are retained for the use of the lead furnaces and the Huntington & Heberlein roasting plant. The largest of these holds about 1,000 tons, while the smallest holds not over

Jan 8, 1915

La central de Paucartambo pertenece a la Cerro de Pasco Corporation, cuya fuerza generada es transmitida a La Oroya mediante una línea de transmisión para 138. 000 voltios. Las partes más importantes de la central son: las obras de captación, el túnel, la tubería de precisión, Casa de fuerza en Yaupi, línea de transmisión, subestaciones y obras complementarias y las obras complementarias como la carretera y los campamentos. Es a partir de la descripción de estas obras componentes, que el objeto del texto señala los métodos de construcción empleados en la perforación y revestimiento del túnel de Paucartambo. El procedimiento utilizado para la perforación de túneles depende de su magnitud y diámetro, encontrándose que el empleo de jumbos para túneles mayores de 3 metros de diámetro es recomendable ya que acelera el proceso de perforación. Mientras que el empleo de cercas de acero es más factible en túneles que tengan mayor tiempo sin revestimiento. En el caso de revestimiento de túneles se sugiere el uso de un equipo moderno que acelere el proceso y mejore la calidad del proyecto. Finalmente, en túneles que requieran grandes volúmenes de concreto, es recomendable el uso de plantas de concreto y laboratorios de campo que los controlen ya que su costo de precio es bajo y la concentración del volumen es mayor.

Jul 20, 1959

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By G. Akdogan, I. Mwandawande, S. M. Bradshaw, M. Karimi

The mixing characteristics of industrial flotation columns were investigated using computational fluid dynamics (CFD). Particular emphasis was placed on the clarification of the relationship between the liquid and solids mixing parameters such as the mean residence time and axial dispersion coefficients. The effects of particle size and bubble size on liquid dispersion in the column were also studied. An Eulerian-Eulerian method was applied to simulate the multiphase flow, while additional scalar transport equations were introduced to predict the liquid residence time distribution (RTD) and particle age distribution inside the column. The results obtained show that particle residence time decreases with increasing particle size. The residence time of the coarser particles (112.5 μm) was found to be at least 60% of the liquid residence time, while the finer particles (19 μm) had a residence time similar to the liquid. The results also show that an increase in the particle size of the solids results in a decrease in the liquid vessel dispersion number, while a decrease in the bubble size increases liquid axial mixing. Finally, the simulated axial velocity profiles confirm the similarity between the liquid and solids axial dispersion coefficients in column flotation.

May 2, 2022

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By Judson G. Brown

In the May, 1969 issue of Mining Engineering the Editorial Director, John V. Beall, described the Japanese Onahama Copper Smelter and Refinery as follows: "On the shore of the Pacific, 120 miles north of Tokyo, is the world's most modern copper smelter and refinery.? One of the improvements that has been made at the Onahama Refinery is the quality of the electrolyte in the copper refinery electrolytic cells. This has been accomplished by reducing the concentration of slimes in the cells between the electrodes. In a December 19, 1966 review in Chemical Engineering magazine reference was made to some tests in Sweden as follows: ?However, at 1,000 amps/sq.M., satisfactory cathodes could be prepared, provided electrolyte flow past the anode and cathode was at least 3 to 4 meters per minute, and the slime content was not allowed to exceed 20 to 30 mg. per liter. By dropping the current to 500 amps with the same electrolyte velocity, the slime content could grow to 50 mg. per liter (50 ppm) without causing occlusion at the cathode." From this data it appears that the production capacity of copper refining electrolytic cells can be significantly increased. In order to do this the concentration of suspended contaminating slimes in the electrolyte solution is reduced by filtration. The electrolyte in-between the active electrodes must be purged with higher velocities to maintain a high concentration of the desirable copper ion in the liquid film adjacent to the cathode and the sulfate ion in the liquid film at the anode. This higher velocity also carries away from the cathode the undesirable impurities released from the anode as they are released into the electrolyte as filterable solids.

Jan 1, 1970

By Chamila Jinendra Nanayakkara, Nimila Dushyantha, Amila Sandaruwan Ratnayake, Gayithri Niluka Kuruppu

Rare earth elements (REEs) are key ingredients in many advanced materials used in energy, military, transportation, and communication applications. However, the prevailing geopolitical dynamics and the rising demand for REEs have rendered the reliance on primary REE resources susceptible to future supply disruptions, posing a substantial risk to the availability of these elements for numerous applications. Therefore, it is imperative to undertake substantial initiatives in the extraction of REEs from secondary sources on a large scale to ensure the resilience of the supply chain. Permanent magnets, lighting phosphors, and nickel-metal hydride (NiMH) batteries are among the secondary sources with high potential for sustainable REE extraction. This review assesses the extraction potential of REEs from the aforementioned three secondary sources and their leaching kinetics and thermodynamics aspects. More importantly, state-of-the-art different existing kinetic models employed in rare earth (RE) leaching were well discussed for a better understanding of the REE leaching reactions. Furthermore, the optimized leaching parameters related to this kinetics were described, and various RE recovery methods were comprehensively summarized. These processes facilitate to managing one of the fastest-growing solid waste streams by minimizing environmental impacts and producing critical metals, including REEs via circular economy approaches. The recovery of REEs from secondary sources aligns with numerous United Nations Sustainable Development Goals (SDGs), particularly in the renewable energy sector for climate change mitigation. Consequently, this trash-to-treasure urban mining concept to transforming e-waste into a valuable resource for REE recovery emerges as a pivotal element within the REE industry.

Dec 28, 2023

By Benson R. P

Building a new tunnel to accommodate CN North America's needs or double stacked container traffic for the next 100 years represents new and unprecedented challenges. Innovative approaches to contracting, especially the Negotiated Compressed Process (NCP), TBM design, project management, and the regulatory and approval process, were all required to deliver a new tunnel to meet the needs of CN North America within the approved completion schedule of 33 months compared to a traditional approach of 45 to 48 months. The NCP resulted in trimming a full 12 months from the project schedule with an anticipated saving of direct and indirect costs.

Jan 1, 1993