Search Documents

By Hector M. Henao

The FeOX-CaO-SiO2 base slag at intermediate oxygen partial pressures is very often used in non-ferrous smelting processes. This slag would also contain Al2O3 and MgO because these compounds are normal components in the ore and the refractory of a furnace. The objective of the present work is to determine the effect of Al2O3 or MgO addition on the liquidus temperatures of the plain FeOX-CaO-SiO2 slags in the atmosphere between intermediate pO2 of 10-6 and that of iron saturation at 1250 and 1300 °C. The experiments were carried out at given mass%CaO/(mass%CaO+mass%SiO2) ratios ranging from 0 to 1 and at spinel-tridimite double saturation. The experimental results show that the effect of Al2O3 or MgO addition on the plain FeOX-SiO2-CaO slag is not uniform and depends on the content of Al2O3 or MgO, the oxygen partial pressure and the mass% CaO/mass% SiO2 ratio. It is apparent that Al2O3 or MgO addition enlarges the spinel or wustite saturation area at almost all the oxygen partial pressures and temperatures of this research. The obtained phase diagrams will be useful in the metallurgical industry to assist in the selection of slag chemistry, operation condition and development of new processes.

Jan 1, 2006

By M. Scherzinger, M. Dr. Mazurkiewicz

Additional progress in comminution can be achieved if the compressive crushing principle commonly used at present is changed to one where particles are fragmented by the tensile growth of preexisting internal flaws or cracks, under internal waterjet pressure. This idea was studied in a number of tests and generated results and conclusions are the subject of this paper. It covers tests with different jets imposed on rock samples during compressive load as well as without any loading.

Jan 1, 1992

By Parker RJ, Swindells CF

The authors have used the geotechnical study for design of the South Wall of Mt. Newman Mining's Mt. Whaleback Mine to illustrate how geotechnical studies can be economically justified. This is achieved by relating the savings resulting from increased ore recovery and prevention of failure to the cost of the study. An outline of the geotechnical study is provided in the paper, including a brief description of the innovative methods used to investigate geological structure of the mine and descriptions of the methods of slope reinforcement adopted.

Jan 1, 1986

Jan 1, 1969

THERE are few industrial and metallurgieal processes which do not require the application of heat energy, and the modern demand for increased working efficiency has resulted in attention being paid to temperature control as a means of ensuring fuel economy and more efficient plant operation. In general, mill accuracy required is not very contant in laboratory work, and few industrial operations are controlled to within less than 5° while in many cases greater limits are allowable. Almost every thermal property of matter has been suggested as a basis for the construction of pyrometers, but the thermo-electric type finds by far the widest application, and hence this paper will deal only with the principles, construction, and uses of this type of instrument. THERMOELECTRIC PYROMETRY.In the year 1821 Seebeek discovered that if the ends of two dissimilar metal wires were joined and one junction heated, a current flowed in the circuit, and the KMF (electro-motion force) set up could be measured by inserting a galvanometer at the cold junction. The phenomenon was not thoroughly investigated for many years, but, as the demand for high-temperature thermometers increased, several investigators, of whom Le Chatelier was one of the pioneers, successfully endeavoured to utilize the principle in pnometric construction. The couples which gave the most satisfactory results were discovered, improvements were made in material and design and the present-day type of instrument gradually evolved. The apparatus consists of three main parts, viz. (1) The thermo-couple itself of two dissimilar metal or alloy wires together at one end. (2) The leads which connect the terminal of the thermo-couple with the measuring instrument.

Jan 1, 1923

Improve the strength and other properties of steel alloys. Approach Research by the U.S. Bureau of Mines indicates that steels melted and solidified under high nitrogen pressure acquire yield and tensile strengths that are up to four times the strengths of comparable stainless steel alloys without nitrogen. Fatigue strength, creep strength, and other mechanical properties are also improved. Strengthening occurs by two mechanisms: (1) increasing dissolved nitrogen in the lattice and (2) formation of dispersed metal nitride phases. Nitrogen Alloying Nitrogen alloying of a steel is generally done by introducing metal nitrides during melting of the steel. The concentration of nitrogen is limited to its equilibrium solubility at 1 atmosphere. For face-centered-cubic (fee) iron, that solubility is approximately 0.4 weight percent (wt%). For body-centered-cubic (bee) iron, solubility is 0.05 wt%. This solubility limitation can be overcome by melting the metal in a pressurized vessel. European steelmakers currently have metal-processing systems that can melt and pour tons of steel under nitrogen pressures exceeding 4 megapascals (MPa) (40 atmospheres). They have achieved nitrogen concentrations as high as 1.0 wt% in these (stainless) steels. The tensile strength is approximately twice the tensile strength of similar steels without nitrogen.

Jan 1, 1992

By Davide Onesti

Electrode regulation is the technology at the heart of the AC and DC Electric Arc Furnace. As such, in the last decade it underwent continuous improvement to maximize the EAF performances, in terms of process efficiency, machine utilization and operator safety. Given this background, Danieli Automation’s efforts in the field of electrode regulation have been focused on fast response to scrap cave-in, compensation of supply variations, automatic resonance detection, transformer protection, dynamic regulation of the electrical and chemical set-points, coordination and control of slagging and foaming agents, arc irradiance supervision. An extensive analysis of operator utilization and feedback was also carried out to develop an innovative system HMI. In this field, the choice of the variables shown to the user is the key aspect to allow a prompt process evaluation by the operator, who can refer to a condensed set of useful data. This paper will describe the innovative features and embedded models of the electrode regulation module (Q-REG+) and the supervision HMI, together with the effects of their application on EAF process efficiency and system usability.

Oct 30, 2017

Societal expectations about how the industry operates and treats its people will be a key driver in the development of the Australian mining industry over the next 20 - 30 years (Moffat, Mason and Littleboy, 2009). Understanding these expectations will be critical in maintaining what much of the minerals industry calls its 'social licence to operate', or its public acceptance or approval. Yet what constitutes this social licence is poorly articulated, with little published research exploring the concept at a local operational level or at the national level in Australia or internationally. This research aimed to explore the societal expectations of the mining industry in Australia and test a participatory methodology to articulate them. Three workshops were conducted with a sample of 24 members of the 'Australian voting public' to explore community objectives for the onshore exploration and mining industry, and the underlying expectations for how the industry should operate in the future. Qualitative analysis of this data revealed three overarching objectives for the onshore mining industry held by participants. They thought that the industry should: advance Australia's national interests (including social well-being); minimise environmental impact, and; act in a socially responsible manner. Within each of these three key themes, or objectives, a number of tensions were evident in the views of participants regarding the trade-offs they are willing to make to secure economic benefit from mining, as well as the basic conditions for socially acceptable mining. These data provide an insight into the conditions for a national social licence in Australia for the mining industry, and the means for its realisation.

Jun 1, 2010

By G. Bonifazi

Certain deposits of incoherent materials which are near the surface and exploitable by open-pit mining may be characterized in real time before they are mined through an analysis of ground-surface imagery. If the slice to be stripped is not overly thick, in fact, surface texture and color properties may be extrapolated to its entire thickness. Image analysis techniques to process ground surface images acquired in situ (or in the laboratory shortly after their acquisition) which yield pattern vectors representative of RGB color component distributions and HSB texture parameters have been developed. The techniques were applied to a mineral sandy ore deposit containing three different lithotypes. Geostatistical analyses showed that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multi-barycenter classification algorithm. Such in situ image-analysis procedures open the way to the proper selection of the ore to be mined, or the proper way for run of mine (r.o.m). processing, or the appropriate blend to be processed before or at the same time as the mining process itself is enacted.

Jan 1, 1999

Jan 4, 1976

Gold recovery from refractory ores can be very difficult and complicated depending on the causes of the refractoriness. Typically, a fine wind and/or the oxidation of the gold-bearing sulfide minerals are required to liberate gold from the host rock matrix. Mineral separation techniques, particularly surface¬wettability based separation (i.e., flotation) and magnetic separation, can be used to pre-concentrate the gold and sulfide minerals, or to remove mineral species that are harmful either to the oxidation of the gold-bearing sulfides or to the cyanidation following the oxidation. In this paper, several processes are described, including oil-agglomeration flotation recovery of fine-grained gold and sulfide, reverse flotation of carbonate minerals prior to pressure or bio oxidation, reverse flotation of elemental sulfur after pressure or bio oxidation but prior to cyanide leaching, and magnetic concentration of gold-bearing iron oxides. The integration of these techniques with gold hydrometallurgical processes may make the economic recovery of gold from an otherwise uneconomic refractory ore possible.

Jan 1, 2011

By Henley R, Harris L

High resolution airborne magnetic and radiometric data have been shown to optimize exploration for epithermal gold deposits in the vicinity of Charters Towers, northeastern Queensland. The radiometric data allow extrapolation of poorly outcropping geology to provide a cost-effective mapping technique, even at exploration scales (eg. 1:25,000). At a regional scale (eg. 1:100,000) the magnetic data reflect the regional tectonics and divide the area into domains for the application of different genetic models. For example: 1. the Ravenswood Batholith is characterized by multiple intrusions dating from Ordovician to Permian age. The polarity of the magnetic anomalies implies an age for the intrusions and indicates a deposit style for exploration. 2. extensional and wrench tectonics along the northern margin of the Drummond Basin are interpreted from the magnetic data and indicate favourable blocks for detailed exploration. Genetic exploration models may be tested in favourable environments by the recognition of geophysical signatures. These signatures reflect structural, lithological and alteration patterns arising from controls on ore deposits and can be applied at regional or detailed scales.

Jan 1, 1989

By Aspinall T. O, Bell L. C

Increased awareness and stricter enforcement of regulatory requirements for adequate rehabilitation of surface mining sites has made environmental planning an essential part of strip mine planning. Rehabilitation is site specific and should be based on data which relate to that site. Cost-effective spoil pile design to minimise erosion is an important part of rehabilitation. Spoil pile design is an integral part of strip mine design. QCT Resources Limited has provided a postgraduate scholarship toward research in this area. The controlling factors of spoil pile design are post-mining land use, drainage requirements and degree and rate of erosion. The extent to which mine design is controlled by these factors is determined by regulatory requirements. To plan acceptable rehabilitation programs, erosion processes must be accurately modelled, and a range of erosion prediction models are available. Useful prediction models can be placed in two categories with the first category containing soil loss prediction models which can be used to predict the amount of soil lost from an area over a short or long term basis. Models in this category include the Universal Soil Loss Equation (USLE), Water Erosion Prediction Project (WEPP), Griffith University Erosion and Sedimentation System (GUESS) and Chemical, Runoff and Erosion from Agricultural Management Systems (CREAMS). The second category contains topographic evolution models which give an indication of the long term morphological development of a formed surface subjected to erosion processes. Models in this category include "Topog", Willgoose's Physically Based Catchment Evolution Model and Areal Nonpoint Source Watershed Environment Response Simulation (ANSWERS). The USLE has been used in the agricultural field for soil loss prediction. To apply the equation to mine sites in Central Queensland, it is necessary to understand the factors affecting erosion at the sites. This understanding should allow the variables of the equation to be quantified. The rainfall factor applied in the USLE is independent of engineering design or soil management techniques. The factor of spoil erodibility is dependent on the material's physical and chemical properties and can vary from site to site. In the equation, the topographic factor, cover and management factor and conservation practices factor can be varied by design to reduce erosion on rehabilitated areas.

Jan 1, 1991

By Irving A. Palmer

During the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part, no doubt, to the scarcity of papers written on the subject. 'There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 1, 1915

By Vishnu S. Gupta

A modular computer program APEX (AMAX Process Evaluation Executive), has been developed at AMAX Extractive R&D, Golden, Colorado to facilitate rapid simulation of steady state material and energy balances of existing and/or proposed metallurgical process flowsheets. Currently, APEX is being used for the design, analysis, and evaluation of several of AMAX?s Nickel, Molybdenumand Tungsten processes. A unique feature of APEX is that it allows specifications of flow rates and compositions for different solid size fractions in addition to aqueous organic and gaseous phases. Thus, a metallurgical process which may involve crushing, grinding, flotation, leaching, washing, solvent extraction, precitation and refining operations can be simulated in a single computer run using APEX. APEX requires two input data files. The first is a process data file which includes physical and thermodynamic properties of the various chemical components of interest. This data file is unique to the process under study and does not require changes for alterations in the process flowsheet. The second data file is specific to a simulation case and includes descriptions of the flowsheet, various feed streams and the process equipment's operating conditions. In addition to temperature, pressure and percent solids, calculated information for each stream includes weight and volumetric flow rates, chemical compositions, specific gravities and enthalpies of solid, liquid and gas phases. For each process equipment in the flowsheet, APEX prints its operating conditions and detailed information about the streams that enter and leave the unit. Models of several general unit operations are preprogrammed in APEX. Also, the modular design of APEX permits quick and easy additions of simulation models which are specific to new and/or unique process operations. To study process stability and optimization, APEX permits several cases of a flow-sheet to be run together. Three simulations of the Moa Bay Nickel process have been excluded to illustrate the ease and flexibility of using the APEX system.

Jan 1, 1980

The financing of mineral ventures is usually supported by the valuation of a mineral asset, the physical size and composition of which have been determined within quantified limits of accuracy in order that the lending or investment risk can be assessed. The Resource or Ore Reserve estimation is the measurement of that asset and may be the outcome of complicated processes of interpretation and estimation requiring an extensive knowledge and understanding of the general nature of ore occurrences, and of the particular deposit under review. In arriving at an interpretation of the nature and physical distribution of minerals in a deposit, observations may only be available from widely spaced samples and geological knowledge and principles are of prime importance. Consultants may be asked by the lending or investing body to "provide comfort" on the quality of the Resource or Reserve estimations and providing such comfort casts substantial obligations of diligence on the consultant.

Jan 1, 1990

By lndu S. Das

An analytical simulation of the material characteristics of Inconel 718 is developed and bounds for mechanical and microstructural stability are obtained for isothermal and temperature-dependent cases. Experimental flow stress data using hot compression tests are reported for a wide range of temperature and strain at various strain rates. A parametric study of strain rate sensitivity, dissipation and entropy are presented. A complete set of processing maps delineating the stable and unstable regions are developed to help define the most efficient means of manufacturing an Inconel product.

Jan 1, 1992

The initiation of cast Pentolite primers by detonating cord has been examined by the combination of two different experimental techniques with computer simulation by the finite element hydrodynamic code DYNA2D. In the first type of experiment, the cord/primer system was placed in a water aquarium, and photographed using a high-speed image converter camera. This highlighted the emergence of the detonation front through the primer surface and the generation of shock waves in the surround- ings. Numerical simulation was used to interpret the experimental record, establishing where the cord had induced buildup to detonation inside the primer. The second experiment used the plate dent test, where the primer was placed in contact with a block of metal (here aluminium), with the resul- tant dent in the metal surface being a measure of primer output. Detailed numerical simulation of this test confirmed that the observed dent was caused by the development of a complex series of shock waves inside the Primer.

Jan 1, 1988

Deposit of Jinbaoshan platinum group metals (PGMs) ore ranks the second in Yunnan province, China. Study on process mineralogy shows that the grade of copper and nickel in the ore is just 0.16% and 0.20% respectively. Moreover, the impurities magnesium and iron and silicon are rich in the ore. The copper and nickel sulfides in the ore, especially the minerals of PGMs, are finely disseminated with the gangues like serpentine. Fine grinding is necessary, and high content of MgO in the concentrate is inevitable through traditional flotation technology on the basis of process mineralogy studies. Achievements on process mineralogy studies are applied to guide the flotation tests successfully. Progress on flotation has been made through comprehensive studies. Suitable grinding by two stages is required for the finely disseminated PGM sulphide ore to achieve the liberation of valuable minerals. Stage grinding and stage separation shall be conducted for a better recovery of valuable minerals. The oxidation state of mineral surface of sulphides has a profound effect on flotation of the ultra-fine sulphides, especially the pentlandite. The combined use of collectors enhances the selective collecting on the ultra-fine and low-grade valuable minerals, is of critical importance.

Jan 1, 2014

By C W. Davis

Every diesel engine emits approximately 100 million nano diesel particles (nDP) per cubic centimetre of raw exhaust. Each nDP has a diameter of between 50 and 70 nano metres or 1/100th the size of red blood cells (diameter of between 6 and 8 microns). When inhaled, some nDP pass through the lungs and penetrate all body tissue [1]. Europe and North America have recognised and are addressing the long term health problems posed by nano diesel particulate matter (nDPM) across their societies [2.3]. Australia has been slow to recognise the issue, at both a societal and mining industry level. There are chronic health effects for every underground miner and serious legal issues for mining companies with increasingly stringent Occupational Health and Safety legislation being implemented at a state level across Australia. This paper will review progress within Australian society and more particularly the underground hard rock mining industry, particularly in Western Australia (WA).

Mar 15, 2021