Search Documents

By W. J. Uren, Charles R. Kuzell

The industries engaged in winning minerals from the earth, because of their widespread dissemination, are faced with perhaps as wide a variety of labor-management problems as may be found in any other broad sphere of productive activity. Those problems are continually increasing in volume and complexity, and management has become aware of their growing importance. For the past quarter century at least, labor-management problems have largely been union-management problems. During this period tremendous assistance has been given labor unions through legislation and administrative and political action. In the United States, legislation favorable to unions has come about in the form of the now defunct National Industrial Recovery Act; the Wagner Act, most of which has been carried forward in the Taft-Hartley Act; the Norris-La Guardia Act; the Wage and Hour Law; the Walsh-Healey Act; and others. The result has been to transfer from the hands of management to those who direct the affairs of the unions a large share of control over the industry and to hamper in many ways the remaining control left to management. In the United States there are many examples of the power of unions to injure whole industries seriously with- out regard to the interests of management, the employes, or the public. This chapter deals with the various phases of labor-management relations as they affect the principal segments of the mineral industry in North America. To the greatest extent possible available data is presented pertaining to the unions involved, their relative strengths, labor law, compensation and fringe benefits of employes, working conditions, and related matters. As background, the historical development of union-management relations in the respective segments is included where possible. The section dealing with the United States has been divided into separate

Jan 1, 1959

By Eli T. Conner

My connection, under a commission from the Councils and Board of School Control of the city of Scranton, Pa., with a recent investigation of mine-caves and the resultant damages to surface-improvements, has led to the preparation, at the invitation of our Secretary, of the present paper. It is notorious that there are, in the anthracite-fields, frequent subsidences of the surface, due to the removal of the coal beneath. No particular attention is paid to such occurrences, unless they happen to injure surface-improvements. Many caves have happened in Scranton and its viciuity, which hare excited but little remark, since they have generally caused no serious damage. In August, 1909, a cave occurred in the Hyde Park section of the city, generally known as the West Side, which nearly destroyed school-house No. 16 and considerable adjacent property. Fortunately, there were no pupils in the building at the time; but the thought of the possible result, had the usual number of pupils and teachers been present, aroused the public to the gravity of the situation; and the School Board employed engineers to investigate the case. Two reports were made by separate sets of engineers, which differed in some particulars. These differences were pointed out in the public press and magnified, and the consequent agitation of the subject was taken up and greatly exaggerated by some of the metropolitan newspapers, giving to uninformed people the very erroneous impression that the whole city of Scranton was in danger of sinking into the bowels of the earth. All this tended to affect the credit of the city and to depress real-estate values. The matter was considered at a joint meeting of the Board of Trade, the Councils, and the School Board. The Hon. J. Ben. Dimmick, a former Mayor, suggested that it

Jan 1, 1912

By Charles Barrett

THE copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possi-bility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previ-ously the structures in this system are unique in their; origin, for one terminal solid solution will precipitate the other, and ice versa. In most of the other systems for which crystallographic data on the precipi-tation (or transformation) process are available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system1 is 779°C. At this temperature copper -dissolves 4.3 atomic per cent (7.0 weight per

Jan 1, 1935

[ ]

Jan 1, 2000

By R. K. Hopkins

Fox a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not withstand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these requirements, but as a result of the extensive research carried on by steel manufacturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By Preston JC, Richards DJ

A multicommodity exploration programme was mounted in the 1970s by CRA Exploration Pty. Limited over a major part of the southern Murray Basin in Victoria. Commodities sought were brown and black coal, gold, uranium, diamonds, titanium and zirconium rich heavy minerals, and base metals. An area of 40 000 km2 was held under exploration licences by the Company. Exploration techniques used were literature research, airborne magnetics and gamma ray spectrometry, drilling, and geophysical well logging. Targets were defined in both the Tertiary basin sediments and the underlying Palaeozoic sedimentary and igneous rocks. Although exploration is continuing, large resources of brown coal and low grade titanium rich heavy minerals have already been discovered. Exploration for uranium was abandoned in accordance with statutory requirements. The search for significant resources of the other commodities has not been successful.

Jan 1, 1986

The paper is aimed at mining engineers and other mining practitioners in the metalliferous mining industry who are considering the use of roadheaders and wish to understand the basic geomechanical and operational principles controlling their performance. The paper aims to address metalliferous minersÆ general unfamiliarity with roadheader technology, which is one of the factors which has limited the application of these machines in such mines. The historical development of drag tool mechanical excavation machines is briefly discussed, and factors affecting the application of roadheaders are mentioned. The mechanics of cutting with drag tools is then reviewed as are the effects of these and tool wear on tool performance. The implications of tool performance to roadheader performance are mentioned, the potential benefits of high pressure waterjet assistance are discussed and the relative performances of different tool types and materials are compared. Roadheader performance factors including productivity and utilisation are mentioned, and the state-of-the-art of conventional roadheaders is discussed in the context of machine weight, power and cutting head configuration. The influence of these and rock strength on machine productivity is analysed. Alternative, developing technologies are discussed which may extend the effective use of mechanical excavation into stronger rock masses which are beyond the range of conventional roadheaders. Finally, conclusions on these discussions are presented, along with recommendations for continuing research and development.

Jan 1, 1997

By Peter Harben

"This paper discusses the benefits of industrial minerals, their sources of supply, price and marketing trends, and their increasing use as substitute materials and ""strategic"" minerals. IntroductionKaolin finds have yet to spark the kind of frenzy associated with the 1849 California gold rush; no dolomite deposit has ever gained the notoriety of the Comstock Lode; and few industrial minerals are counted among the currently fashionable list of "" strategic mineral s"". Nevertheless, the glamorous zhine associated with metals may be somewhat superficial; further digging provides perhaps the real foundation of modern society - industrial minerals.They are often tagged as common, everyday materials that are simply dug out of the ground, crushed and hauled to a local point of consumption. Although this description is accurate in the case of road aggregates, sand and gravel, and the like, there are many exceptions to this rule. The term industrial minerals is rather nebulous, covering as it does the mundane and esoteric, the chemically active and the refractory, the $2 and the $10m-a-ton product. All of these minerals influence every facet of modern life from fertilizers to fire retardants, ceramics to cars, construction to clothes, and toothpaste to tennis courts. Their usefulness is well illustrated by the variety of industries they serve; the main ones are listed in Table 1. It is now time to dismiss the notion of non-metallics as the ""third world"" of natural resources business after the metallic and energy products by dispelling some of the myths regarding abundance, variety and value of the group's sixty-plus products."

Jan 1, 1982

By Andre Vien, D. H. Hendriks, D. Willet, B. C. Flintoff

"For many years the training of mill operators was an informal process which involved senior operators training junior operators on an as-needed basis. Recognizing the needs and benefits of better training some companies, and even some provinces through legislation, have moved to ensure that a formalized training program exists in the plants. These programs tend to focus on basic safety and operations. Much remains to be done. With the more rapid incorporation of new processing and information technologies, and the goal to keep labour costs to a minimum by doing more with less, operator training has become a critical issue. This paper briefly examines the evolution of training programs, provides some measure of their effectiveness, and explores some recent developments which could have a very significant impact on the industry.PreambleOne can draw an analogy between operator training and the mechanical support of production equipment. When we buy a piece of process equipment it is critical that the mechanical installation be done properly to ensure that the device will operate at peak performance on start-up. Once the equipment is running, some form of preventive maintenance is required to ensure continued efficient operation. The operators and the equipment are both elements of the processing system, yet the former do not seem to get the same ""start-up"" or ""operating"" support. Are they not seen as critical to efficient operation? Why is this so? What impact does it have? How can we improve?These are all very logical and important questions, although the answers are not nearly so obvious. In the mineral processing industry, progress in operator training over the past thirty years has been limited and quite variable. To address the perceived need for a more coherent and consistent approach, some provinces have moved to incorporate basic training requirements in their legislation. Some plants have gone a few steps further by building integrated training programs into their operating culture. One conclusion which can be easily reached is that there are no standards, and that the range of training activity is great. In other words, a flotation operator is not a flotation operator is not a flotation operator. Their knowledge and skills are very much a function of training and experience, which are clearly corporate and site specific."

Jan 1, 1994

By J. O. Brittain, E. P. Lautenschlager, D. A. Kiewit

Compression tests were run in the temperature range of 700° to 900°C ox 0' phase NiAl intermetal-lic alloys of several grain sizes. At these temperatures the minimum strengths were observed at the stoichiometric composition. While significant increases in strength occurved in both the low-nickel (vacancy) and high-nickel (substitutional) regions, the highest strengths were found in the high-nickel region. During deformation serrated flow was sometimes observed in the low-nickel alloys. After deformation transgranular cvacking and deformation striations were observed in all compositions tested. AS part of a general investigation of the properties of NiAl inter metallic compounds, a preliminary study of the role of point defects upon plasticity was made by high-temperature compression tests on ß' NiAl specimens of several grain sizes and compositions. ß' NiAl is an intermetallic compound having a CsCl structure and a rather wide range of composition from A1-45 at. pct to 60 at. pct Ni.1 According to Bradley and Taylor2 and to cooper,' it possesses a defect lattice in which departures from stoichiometry in the direction of decreased nickel content lead to the presence of vacant nickel sites (although Cooper's work indicates that a small amount of substitution also occurs) whereas departures on the high-nickel side lead to substitution of nickel on aluminum sites. NiAl forms congru-ently from the melt at approximately 1650°C,1 and thus has a higher melting point than either of its component elements. Up to this time, although this and other high-melting intermetallic compounds have been suggested for elevated-temperature usage,4 only the hardness4 and a few tensile-strength measurements5 have been reported for NiAl at high temperatures. In the present investigation the effects of composition upon the compressive-strength properties in a range of 700° to 900°C have been measured for NiAl of several grain sizes. EXPERIMENTAL PROCEDURES The alloys were made as described elsewhere6 from an A1-46.8 at. pct Ni master alloy furnished by the International Nickel Co. with additions of high-purity nickel and aluminum. The charges were vacuum-induction-melted in A12O3 crucibles with small amounts of helium added to the atmosphere to suppress vaporization. They were cooled slowly from the melting temperature to achieve uniform grain size. In order to refine the as-grown grain size a special rolling technique was developed. Alloys were packed into 0.10-in. wall-type 302 stainless-steel tubes which were partially filled with magnesium oxide to prevent bonding between the alloy and the steel jacket. The ends of the tubes were closed by hot forging, and the packets were then hot-rolled. The alloys with greater than 50 at. pct Ni were rolled at 1100°C, but it was found necessary to increase the temperature to 1350° C before alloys with less than 50 at. pct Ni would roll without cracking. With these temperatures, reductions as high as 48 pct were achieved in a single pass. The rolled alloys will hereafter be referred to as "fine grained" whereas the as-grown material will be designated "coarse-grained''. The compression specimens were made by cutting square cross-sectional pieces, approximately 3/16 by 3/16 by 1/2 in., with a water-cooled diamond cut-off wheel from the as-grown or the rolled alloys. Specimens were ground to their final dimensions by polishing through 3/0 grit silicon carbide papers. The final shape was a rectangular parallelepiped of square cross section having a height-to-width ratio of 3:1. Compression testing was carried out in a compression rig of our own design mounted on an In-stron Floor Model. The specimen chamber could be heated to 1000°C and was controlled within ±2°C. The compression rig was enclosed within a bell jar and was maintained at a 50 µ of mercury vacuum throughout the duration of the test. The test cham -ber was heated from room to test temperature within 15 min. Specimens were then held at the test temperature 30 min prior to testing. Previous experiments indicated that no grain growth would occur within this time. An Instron Variable Crosshead speed unit was used to adjust for small variations in specimen lengths in order to have a constant initial strain rate, €, for all specimens of a group. For the fine-grained specimens the strain rate was changed rapidly at constant temperature by a factor of 10 with the speed lever on the Instron. For a given € the compression data was analyzed in terms of true plastic strain (E) and true compressive stress (0).

Jan 1, 1965

By E. Miller, J. M. Eldridge, K. L. Komarek

Aclivilies of magnesium in liquid Alg-Si alloys have been delermined between 5 and 60 at. pcl Si, close to the melling point of Mg2Si, by an improved isopieslic melhod. Silicon specinrens, held in alumina crucibles and graplrile conlainevs of special design, were healed in a letrlpevalure gvadient and equilibrated with mag-nesilcrrl rapor in a closed lilanium system. The ther-madynamic Junctions were calculated and compared with the thermodyuamic properties of the other three mg- Gvoup IVB systems. Lattice paramelers of three Mg2X compounds were measured. The bonding in the Mg2X compounds is largely covalent with small and uarying amounts of metallic and ionic conlvibutions. The Mg-Si phase diagram1 has one congruent melting compound, Mg2Si, of essentially stoichiometric composition, two eutectics, and very limited terminal solid solubilities. Little information is available on the thermodynamic properties of this system. The free energy of formation of Mg2Si has been determined by the Knudsen cell technique2 in the range 572" to 680oC, by the transportation method3 between 858" and 950oC, and by the electromotive-force method4 in the range 400o to 600°C. Kubaschewski and villa5 and caulfield6 have measured the heat of formation of Mg2Si. An electromotive-force study of magnesium-rich liquid alloys was recently published by Sryvalin el al.7 The present investigation was undertaken to complete a general survey of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,a9,Mg-Sn,10,11 mg-Ge,12and Mg-Si. An isopiestic technique, previously developed for similar measurements on liquid Mg-sn11 and Mg-Ge alloys,12 was modified for the Mg-Si system. Specimens of the nonvolatile component, silicon, were contained in dense alumina crucibles placed inside covered graphite crucibles which were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure. The alumina crucibles prevented contact between the highly corrosive liquid Mg-Si alloys and graphite. The graphite cruci- bles effectively preserved the high-temperature equilibrium composition of the liquid alloys containing highly volatile magnesium on termination of the experiments during the quench to room temperature. EXPERIMENTAL PROCEDURE Silicon of semiconductor-grade purity (E. I. du Pont de Nemours and Co., Brevard, N.C.) and 99.99+ pct Mg (Dominion Magnesium Ltd., Toronto, Canada) were used. Graphite crucibles with press-fitted lids were machined from high-density (1.92 g per cu cm) rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The alumina crucibles had a purity of 99.7+ pct (Triangle RR grade, Morganite, Inc., Long Island City, N.Y.). In preliminary runs the liquid alloys were contained in graphite crucibles following the exact procedure developed for the Mg-Ge system.'2 These runs failed due to appreciable reaction between the molten Mg-Si alloys and graphite, and the results have been discarded. The procedure was then modified and the Mg-Si alloys were subsequently held in alumina crucibles. For most of the runs alumina crucibles of known weight and approximately 6.3 mm ID, 12.5 mm height, 1.0 mm wall thickness were loaded with weighed amounts of silicon and encapsuled in tightly covered weighed graphite crucibles 5/16 in. ID, 2 in. helght, 3/32 in. wall thickness). The graphite crucibles were machined from rods which were 85 pct of the theoretical density. These crucibles were therefore sufficiently porous so as to permit magnesium vapor to effuse through the silicon under the experimental conditions of approximately 970O to 1220°C and 1 day equilibration time. However, negligible magnesium was lost from the crucible during the quench due to the slow effusion rate through the pores of the graphite. The inner alumina crucible prevented the liquid alloys from contacting the graphite, and the very tightly fitting graphite crucible lids served to retain any magnesium vaporizing from the alloys inside the crucibles during the quenching step.12 The loaded silicon-alumina-graphite cells were positioned, one above another, on a 16-in.-long titanium thermocouple well and tied securely to the titanium tube with thin molybdenum wires held in grooves around the circumference of the graphite crucibles. A thin (0.005-in.) molybdenum strip prevented contact between the graphite crucibles and the titanium. This assembly was lowered into a titanium reaction tube (la in. ID, 16 in. long, $ in. wall thickness) closed on one end which contained a 11/2-in.-long cylinder of magnesium at the bottom. The inner titanium thermocouple well was positioned eccentrically in the large tube because of the eccentric mounting of the cells on the well. Appropriate modifications of the titanium cap"'12 were made to join the inner and outer titanium

Jan 1, 1968

By Allan B. Bowman

Several years ago a wealthy Chinese business friend of mine purchased an interest in a pro- posed oil well to be drilled a great distance from his home. A few months later it came in as a producer and proved to be a huge success and materially added to his resources. I asked him why a man of his wealth should be so lucky in a venture outside his sphere of knowledge when most people of modest means never seemed to get ahead. His answer was, "Fat Hoy takes a chance." Even though this was his answer, I knew from my association with him that there were other tempering considerations which Mr. Hoy applied before making up his mind to enter any transaction. First, he was a cautious individual. He was also a great believer in details and insisted on knowing everything possible about a situation, and finally, he was what we call a very solid individual with good basic instincts and judgment. This philosophy of Mr. Hoy may be applied to most any business but especially to those engaged in a search for natural resources such as mining where great risks are involved. This article concerns events in the history and growth of Banner Mining Co., with which I have been associated for 27 years in capacities from mine surveyor to vice president. Mr. Hoy's philosophy has played a significant role in the exploration projects of this company over the years, but what is more important, the officers, directors, and controlling interests in Banner have been aggressive in their search for ore reserves.

Jan 6, 1963

By M. J. Pool, P. J. Spencer

Using liquid tin as the solvent metal, the heats of solution of silver and gold in dilute Ag-Au-Sn alloys have been determined at 723°K by solution calorimetry. From the values obtained, the various enthalpy interaction coefficients in the liquid solutions have been calculated. The self-interaction coefficients Au and Ag values of 2413 and -6322 cal per g-atom in binary Au-Sn and Ag-Sn alloys, respectively. For an alloy containing 0.04 mole fraction Ag, Au is equal to 2443 cal per g-atom, and in an alloy containing 0.04 mole fraction Au, Ag has a value of —8883 cal per g-atom. Ag Au has been determined as —2650 cal per g-atom. ADDITION of a second solute to a dilute binary alloy may cause striking changes in the thermodynamic characteristics of the alloy. As yet, such influences cannot be reliably predicted and it is only by accumulation and critical assessment of data that definite patterns can be established. Solute interactions in dilute solutions were first treated mathematically by Wagner,1 who derived expressions for the Gibbs energy interaction coefficients. For an alloy consisting of. two dilute solutes, i and j, in a solvent s, these coefficients are given by: where yi is the activity coefficient of component i and x represents the mole fraction of solute or solvent. Other interaction coefficients have since been established in terms of the various partial molar thermodynamic properties of an alloy; the definitions of these are summarized in a recent paper by Lupis and Elliott.2 Mathematical and experimental studies of such coefficients have received much attention recently, providing a very useful theoretical background to an understanding of the nature of solute interactions taking place in dilute solutions. One of the definitions to arise from such work has been the extension of Wagner's treatment by Lupis and Elliott4 to include an enthalpy interaction coefficient, defined as. where ?Hi is the relative partial molar enthalpy of component i. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hio, and to the enthalpy interaction coefficients by the expression: Values of ?Hi can often be obtained with a high degree of accuracy by calorimetry, and, if the composition of the alloy is carefully controlled by making calculated solute additions throughout a series of measurements, application of Eq. [2] will enable reliable enthalpy interaction coefficients to be determined. Partial heats of solution must be investigated as a function of solute concentrations down to xi = 0, and, since ? values are obtained from the slope of mi plotted against x, great care must be taken to obtain precise data. The data for binary systems which are presently available often require extrapolation of ?Hi values from compositions as great as xi = 0.05 or even 0.1 to obtain limiting heats of solution. Reliable enthalpy interaction coefficients are thus impossible to obtain from published data for most of the alloy systems already investigated. The aim of the present work was to determine values of Au, Ag, Ag, and Au in the limit xsn -1 for the relatively simple Ag-Au-Sn system and from these results to gain some insight into the possible influence

Jan 1, 1969

By A. C. Freeze

The first use of electric punched card accounting machines as an aid in calculating reserves at the Sullivan mine in Kimberly, B.C., was made in January, 1948. At that time their use was limited to totalling individual reserve blocks for the various reserve classes and for calculating total metal content. The immediate objective was to increase speed, improve accuracy, and to effect some savings in labor that could be employed more usefully elsewhere. It was recognized also that the potential for achieving even greater advantages was excellent. The initial experiment proved so successful that it was inevitable that the use of the method would expand. Thus, for the past nine years assay data from core hole and development headings have been processed by these machines and the results integrated with the program of calculating reserves. It was also learned that the machines could store and classify a large amount of other information concerning the mining characteristics of each reserve block in addition to tonnage and metal content. This has proven very useful for the preparation of monthly production reports as well as in long term planning, in forecasting production schedules, and in analysing the results achieved.

Jan 4, 1961

By Wilfrid Comeau

Vibrograms, which last significantly longer than the actual blast (say 10 to 15 cycles or more), may be signalling an elastic response, which is not uniquely blast related. For example, geophones mounted on a part of a structure, which can elastically resonate at a frequency included in the seismogram, may not show the structure’s real reaction to the blast. This resonance usually amplifies the ground vibration. This contribution examines one particular case where blasting excited and amplified a resonant ground response, and the method used to significantly reduce or eliminate this undesirable condition.

Jan 1, 2007

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite (CuzS) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical eqUilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

Jan 1, 1943

Jan 1, 1943

By Mictck Rataj

Methods of rock reinforcement in Australian coal mines are being advanced progressively through the better understanding of rock failure mechanisms around roadways and the-development of improved bolting hardware and installation techniques. It has been recognised that to improve the performance of rock reinforcement systems, the stiffness of the system as a whole has to be improved. New style bolts and accessories together with high pre-tensioned roof and cable bolts are being developed as a result. A number of the new techniques used to stabilise the roof, especially in weak roof/high horizontal stress areas have been site proven and are now currently used on a routine basis as a means of improving development rates and gate road stability during longwall retreat.

Jan 1, 1997

By Carthew J

For more than 30 years shearer loaders have been the most important winning machines for,longwall mining. While the machines of the first generation had a driving power of only 100 or so kW, the present day shearer loaders may be powered by more than 1000 kW. Daily outputs of 24000 tonnes have now been reached, but this still does not set a limit. If the deposit conditions allow, further increases are possible. This requires the optimum coordination of all system components. For this paper the use of coal plows has been of little import as plows have found no favour, and nor are they likely to do so in today's economics in Australian coal mining.

Jan 1, 1988