Search Documents

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to overproduce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metalbased economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening.

Jan 4, 1973

By H. W. Turner

The axis of the middle portion of the Ural mountains is made up chiefly of highly compressed igneous and sedimentary schists, considered of Devonian age by the Russian geologists, with large areas of serpentine (peridotite originally) gabbro, etc,, intrusive in the schist series. In addition there are large areas of probably older granitic and gneissic rocks. The nickel deposits referred to in this paper are found in the Devonian schists and their associated igneous rocks. The gabbro-peridotite intrusions probably took place in late Devonian or early Permian time, inasmueh as the Permian and Carboniferous beds lie at gentle angles on the Devonian series on the west slope of the Urals. Perhaps the first attempt to work a nickel deposit in the Urals was made about 1866 in the Revdinsk district, which is situated southwest of Ekaterinburg. 3 was informed by a Russian that a wet method of extracting the nickel was tried but was not a commercial success. This deposit has been described by Muller,l Foullon, and Karpinski.3 Beck4 gives an abstract of these papers. ; Lying to the southeast of the Revdinsk district, the Sissert estate intervening, is the Verkhne-Ufalei district, which is traversed by the railroad from Ekaterinburg to Cheliabinsk, as shown on the map, Fig. 1, there being a station on this railroad at the iron-smelting town of Verkhne-Ufalci. About 7 versts (4.6 miles) north of this town is the Nijni-Karka-dinsk iron mine, which is a limonite deposit. In one of the shafts in this mine a serpentine rock showing a green mineral was encountered. A sample of this mineral collected in 1910 was tested by Mr. Wyatt, chief chemist of the Karabash laboratory of the Kyshtim Mining Works, and determined as nickel ore. A thin section of one piece of the serpen-

Jan 1, 1915

By W. F. Baldwin

The timing circuit generally employed in Carter Reservoir Behavior Analyzers consists of a synchronous motor driven cam which actuates a microswitch. A mechanically actuated timer of this type has several inherent disadvantages, among which are the following: 1. The first time interval may not be of uniform length, depending on the exact position of the cam at the conclusion of a previous run. 2. The positioning adjustments on the microswitch lever arms are critical and require periodic readjustment. 3. The mechanical system is subject to wear which will ultimately impair its accuracy. It was therefore considered desirable to devise an alternate method which would eliminate these difficulties without introducing others that would be equally troublesome. This note describes the design of an electronic timing device which has been incorporated in the analyzer constructed by the Field Research Laboratories of Magnolia Petroleum Co. The electronic timer circuit is built around a simple neon glow tube relaxation oscillator, the complete circuit diagram of which is shown in Fig. l. The operation of the circuit is as follows: Condenser C, is charged to the critical firing voltage of the neon glow tube VR-75 by battery B1 through resistors R1 and R2. When the neon glow tube fires, the condenser C, is discharged, The charging cycle then repeats itself,

Jan 1, 1950

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

The ASC has a dual role of business facilitator and law enforcer. Only certain types of expert report are of interest to the ASC. The powers of the old Companies Code and the Corporations law are compared. NCSC Policy Release 149 was dependent on the prescriptive powers given to the NCSC in the Companies Code. The Corporations Law does not give the ASC power to prescribe the contents of expert reports. The requirement now is for all necessary information. Research evidence is that some investors want simpler prospectuses while others need more detail. The ASC's examination of expert reports is after registration of primary documents. This leads to a necessity for experts to maintain adequate records.

Jan 1, 1994

By H. Vigil Fernandez, G. Peach

The Musaimeer pump station and outfall project located in Doha Qatar, was designed to collect and manage ground and stormwater and then discharge the treated waters offshore. The project constructed a long outfall tunnel using an EPB TBM with segmental lining, each tunnel ring being 1.35 m in length with an internal diameter of 3.7 m.. The diffuser structure was a 6-arm structure, measuring 294m by 40 m connected to a central manifold in turn connected to the TBM constructed tunnel via a riser shaft drilled from an off-shore barge. This technical paper will discuss the planning, methodology and construction practices employed to connect the TBM tunnel to the diffuser structure 10.2 km offshore.

Jun 13, 2023

By W. P. Yant, R. R. Sayers, H. W. Shoaf, John Chornyak

"The contemplated use of dichloro-difluoro methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for Public buildings and possibly homes, brings attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorine compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines was requested to make a laboratory study of the toxicity and potential hazard:"" and it was on the basis of the results of this work and the results of a preliminary investigation made in another laboratory5 that the compound has been selected for commercial use. Although the investigation conducted by the Bureau of Mines is still in progress, information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:Additionally work rich is in progress at the present time includes a determination of the lethal time-concentration curve for animals and a study of the response of persons within the range of safe concentrations.The writers desire to jive acknowledgment to T E. Midgley, Frigidaire Corporation, Layton, Ohio, for suggesting the investigation, for arranging for the cooperation of the Frigidaire Corporation, and for advice during the experimental work; to Robert A. Kehoe, The Eichberg Laboratory of Physiology, University of Cincinnati, Cincinnati, Ohio; and E. R. Hayhurst, college of Medicine, Ohio State University, for consultation and advice in planning the work; and to the following employees of the Bureau of Mines for assistance in performing the experimental work: L. M. Berger, chief scientific aid, S. J. Pearce, junior chemist, and Ethel B. Stead, technician."

May 1, 1930

By S. Chatterjee

Mining represents the first industry in the United States to have federally mandated training for its workers. Although the topics to be covered are specified in 30 CFR 48, course content is left to the discretion of the individual mine operators. Unfortunately, certain topics to be covered, such as prevention of accidents, are usually mine specific, making it very difficult to use the same course content in every mine. Further, training requirements may change from one mine to another, due to changes in the demographic characteristics of the workers, or changes in job and organizational characteristics. Therefore, if the intention of safety training is to modify the behavior of workers, it is expected that there should be some changes in the content of safety training programs in order to address the specific requirements of individual mines, or at least mines of similar worker and job characteristics. This study has been directed towards the development of a systems-based procedure for conducting a needs analysis. A special effort was made to understand the psychology of worker behavior by analyzing worker reactions to various organizational and job characteristics.

Jan 1, 1994

By David L. Kuck

Siderophyle platinum-group metals and sane gold are a thousand times more abundant in metal and chondritic meteorites than in terrestrial or lunar rocks. Type I and II carbonaceous chondrites contain granules of the high boiling point metals W, Re, Mo, Ir and Os. Metal meteorites and the metal fractions of other chondrites contain siderophyle Pt, Pd, Ru, Rh, Os, Ir and Au. Spectra of sunlight reflected from asteroids, when compared with those of meteorites and specific minerals, provide a rough classification and guide to sources of precious platin-group metals.

Jan 1, 1982

By E. P. Barrett

THE high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,1 in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. SHAPE AND SIZE OF CENTRIFUGAL LIQUID CRUCIBLES When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape f a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 ½ in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections f the cylinders, shows the effect f speed f rotation of the containers upon the shape f the inner surface f the rotating liquid crucibles.

Jan 1, 1938

By M. Metzger, L. E. Hendrickson

Grain boundary attack in 16 pct HCl was found to be substantially the same at low penetrations in zone-refined aluminum (individual impurities 0.1 at. ppm), superior electrolytically refined aluminum (51 at. ppm), and aluminum with various impurities at much higher levels. It was concluded that impurity atom segregation affecting corrosion would have been detected and that the corrosion susceptibility did not originate in this segregation but in the structure of the boundary. It was pointed out that the significance of most previous studies in this system had been obscured by an unrecognized autocatalytic copper reaction. Although general corrosion rate was also impurity-insensitive , there was shallow pitting attributed to iron seg-regation and a hillocked surface texture associated with copper; these were interpreted as due to cathodic damage affecting- cathode distribution. THE grain boundary corrosion suffered by high-purity aluminum in hydrochloric acid has been the object of some interest (the earlier work is summarized in Ref. 1). The central metallurgical question here is whether the corrosion susceptibility of a boundary originates in its structure or in impurity atom segregation. An attempt to study this question revealed large catalytic effects associated with small quantities of the copper impurity in the aluminum, 220 ppm, or in the corrodent, and these magnified the preferential boundary attack and obscured the intrinsic susceptibility question.' After the catalytic effects had been examined,"' test conditions could be designed to avoid them and methods developed for studying the shallow boundary penetrations prevailing when they were absent.= It then became possible to determine whether intrinsic boundary corrosion in aluminum involves impurity segregation. The older work provided no firm information on grain boundary segregation of specific solutes influencing corrosion although several studies suggested iron segregates.4,5 perryman4 found in 10 pct HC1 that the slowly developing (microns per month) grain boundary grooves were deeper in material of higher iron content (range 10 to 550 ppm, with 5 to 80 pprn Cu) but he did not measure the depths of general corrosion, which were probably several times greater, and his reference surfaces may have varied more than did the groove depths. Metzger and Intrater's results for 20 pct HC~,' which yielded higher time-average rates (mm per month) and deeper penetrations, suggested that boundary segregation of iron (range 4 to 230 ppm, with 22 pprn Cu) decreased the penetration rate. However. in the stronger acid the autocatalytic l.E. HENDRICKSON, Student Member AIME ,and M. METZGER, Member AIME, are Research Assistant and Professor of Physical Metallurgy, respectively, Department of Mining, Metallurgy and Petroleum Engineering, University of Illinois, Urbana, Ill. Manuscript submitted March 11, 1968. IMD effect of the copper impurity is greater1,2 and it is now evident that their corrosion rates had been much magnified by this effect and did not provide a proper basis for the analysis of segregation. In exploratory studies of other solutes (made under the same conditions), 1000 ppm additions of Mg, Mn, or Si or 100 ppm Ca were without effect.1 Montariol6 noted that boundary attack in 22 pct HC1 persisted after zone refining although with fewer deep fissures (ranges 0.06 to 4 ppm Cu, 4 to 23 ppm Fe). Autocatalytic effects may have influenced these results also and those of Perryman.4 The present objective was, as a first step, to see whether quantitative tests designed to exclude autocatalytic influences would indicate the existence of low-level impurity effects on intrinsic boundary corrosion. Comparison of electrolytically refined with zone-refined aluminum of lower copper and iron contents revealed no differences in boundary corrosion, but certain impurity-sensitive differences in general corrosion morphology were noted and investigated further at higher impurity levels. I) EXPERIMENTAL PROCEDURE A) Material. A selection from commercially available material was made with the cooperation of several producers. An electrolytically refined lot (III-A, 1 ppm Cu, 2.4 ppm Fe) studied previously3 provided a starting point. Since material of substantially higher copper content could not be used if the autocatalytic corrosion reaction were to be avoided,2,3 a lot (III-B) of about the same purity was added as a check, two zone-refined lots (I-A and I-B) with copper and iron an order of magnitude lower were selected for comparison, and an intermediate lot (11) was included. Analytical data are given in Table I. For copper in I-B and iron in I-A and I-B, the actual concentration is thought to be near the limit given, i.e., about 0.1 ppm. For titanium, vanadium, and chromium in III-B, the actual amounts are thought to be, like those in III-A, substantially lower than in the zone-refined lots (these elements concentrate in the solid on freezing). Data are given later for some additional lots surveved. B) Specimen Preparation and Procedure. one by 3 cm blanks with a notched stem were cut from 1-mm cold-rolled sheet, annealed 24 hr in air at 650°C, and quenched in an air stream (42°C per sec initial cooling rate, 100 sec to cool to 100°C). The high annealing temperature maximized diffusivities and approach to equilibrium impurity distributions. A water quench, in principle more efficient in preserving the distribution established, was undesirable because the boundaries were almost plane and they tended to shear and migrate during the quench and thus to be separated from any existing impurity atmosphere. Test procedures, previously described,3 involved electropolish-ing, etching 2 min in 10 pct HF at 24.0°C, and expos-

Jan 1, 1969

By E. V. Leont'eva, V. R. Vafin, A. G. Kladova, N. L. Medyanik, A. P. Ponomarev

"The thermochemical technology for recovery gold, silver from mature flotation tailings of pyrite ores by two-stage sintering with chlorine-ammonium reagents and leaching of bakes with water is developed. The economic effect of the technology implementation is calculated. KEYWORDS Gold and silver recovery, mature flotation tailings, pyrite ores, chlorine-ammonium reagents, leaching INTRODUCTION The relevance of processing the technogenic reserves of ore mining and concentration wastes accumulated over the long operation periods of mineral deposits is beyond doubt. Hundreds of tons of precious and non-ferrous metals that were not recovered during the primary processing are concentrated in the accumulated wastes. For example, tailing storage facilities (TSF) at the mineral processing plants in the Southern Urals region of Russia hold more than one hundred tons of gold and thousands of tons of silver in the mature flotation tailings (MFT) of copper pyrite ores. Secondary processing of technogenic materials is facilitated by the fact that they are preprocessed — ground and compactly deposited on the surface, but complicated by the low (compared to ores) grade, uneven distribution of the valuable minerals, altered and unstable material composition of the mineral feed. This leads to low recovery rates of valuable metals by conventional physicochemical processing methods. It is necessary to develop innovative methods of deep integrated processing of industrial wastes, based on the study of the material composition of specific technogenic mineral resources and based on ensuring the environmental safety of the resulting secondary waste. MATERIALS AND METHODS The object of this study are the MFT of Uchaly Concentrator in the Republic of Bashkortostan, Russia, which processes copper pyrite and copper-zinc ores. According to the data of particle size, chemical, X-ray phase, and optical microscopic analyzes, samples of the MFT are characterized by considerable particle fineness (the fraction of the size class -41 µm is 89-90%), low grade of gold (1.7-2.0 g/t) and silver (18.0-19.5 g/t), comparable grades of iron (23.0-26.8%) and sulfur (28.1-28.7), but different grades of copper (0.12 - 0.73%) and zinc (0.34-1.26%). The most common mineral in the samples is pyrite (50 - 56%), found in intergrowth with grains of other sulfides (0.1-4%) - sphalerite, tennantite, chalcopyrite, covellite. Quartz and aluminosilicates are the dominant rock minerals (21-36%). Based on the results of the phase analysis, it was established that approximately 70% of the gold in the samples is found in a form that is resistant to cyanidation — it is locked in sulfides (52-56%) and quartz and coated by films. Along with sulfides and rock minerals, common gold and silver minerals (chalcogenides, intermetallides, native gold) in the form of submicro- and nano-sized precipitates are also associated with intergrowth of a complex structure. These features of the material composition allow classifying the MFT of the pyrite ores as a mature feed material and emphasize the need for chemical non-cyanide methods to recover gold and silver from the mature minerals and associations they are found in."

Jan 1, 2018

By Frank J. Wiebelt

The Carbonate King zinc mine is on the west slope of Kokoweef Peak, Ivanpah Mountains, San Bernardino County, Calif. It has produced more-than 10,000 tons of ore with a 39-percent?zinc content since mining operations began in 1940. The ore, consisting principally of calamine and smithsonite, occurs in replacements of the YellowPine limestone. Milling, has been done from the surface to a depth of 275 feet. Eight holes, aggregating 2,121, feet were drilled by the Bureau of Mines in an endeavor to establish extensions of the worked-out ore bodies and to develop new ones. Although indication of mineralization was found in several of the holes, no new ore bodies were developed.

Jan 1, 1949

By Alexandre Bonan

The paper reports on the results of a kinetic study on the oxidation reaction of aqueous free cyanide ions with H202, in the presence of Cu(2+) catalyst. The variables and respective ranges studied were the following: (CN) ° = 10 -100 mg/l pH = 10 -11 (H202/CN) mol ratio = 1 -3 (Cu/CN) mol ratio = 0 -0.25 The results lead to the development of a semi-empirical model whish incorporates both the useful oxidation reaction and the parallel alkaline decomposition of H202.

Jan 1, 1992

By Gennaro Delisle

"Les Services TMG (Niobec) currently treat a niobium ore in the Chicoutimi area of Quebec. The mineral pyrochlore is present in a carbonatite deposit which assays 5% to 7% apatite.The ore is ground to minus 65 mesh and deslimed at 10 micrometres. Part of the carbonates are floated with a fatty acid emulsion and rejected to the tailings as a first step to ensure the proper conditions for the flotation of the pyrochlore concentrate. The carbonate concentrate is 65% minus 44 micrometres and is composed of dolomite, calcite, 22% apatite and a minor amount of silicates.A laboratory investigation was undertaken to determine the feasibility of extracting apatite from the carbonate concentrate. This led to the development of an economic flowsheet to produce high-grade apatite concentrate. The apatite is depressed with phosphoric acid, and the pH is adjusted at 4.8-5.0 with sulphuric acid. An additional amount of fatty acid is added to permit efficient flotation of the carbonates. 1n a second stage, the silicates left behind with the apatite concentrate can be removed by depressing the apatite with AIC3 while floating the silicates with a secondary amine.The results of the laboratory tests indicate the possibility of producing an apatite concentrate assaying 38.3% P2O5 (83.7% BPL) with a recovery of 66.2%. Pilot-plant tests undertaken at the concentrator yielded a concentrate of 34% P205 and recovery of 76%."

Jan 1, 1981

By A. Bartkowiak

The lower flammability limit of methane at 0 p.s.i.g. and ambient temperatures is 5.6 volume percent in chlorine, 5.2 in oxygen, and 5.0 in air. The corresponding upper limit values are 70, 60.5, and 15 volume percent, respectively, so that the range of flammable mixtures is greater in chlorine than in oxygen or air. The lower flammability limit of ethane at 0 p.s.i.g. and ambient temperatures is 6.1 volume percent in chlorine, 3.0 in oxygen, and 2.9 in air. The corresponding upper limits are 58, 66, and 12.5 volume percent, respectively. In this instance the range of flammable mixtures is greater in oxygen than in chlorine or air. Generally, the limits of flammability for both methane-chlorine mixtures and ethane-chlorine mixtures widen with increases in temperature and pressure.

Jan 1, 1960

By Mauro Chiesa

A. New Dictionary, Since 2007/8 Traditional concept of ?cycle? is dead A dearth of projects AND good metal prices suggests otherwise In a depletion-business, good times for any greenfields in 2-3 yrs! ?Balance? sheet means quality assets = quality capital So, de-risk the assets, and ration the capital ?Replacement costs > historical costs ?Discounted assets depleting; replacement costs need self-financing (FCF) ?Public-sector slows permits, avoids assets and wants more of FCF ?Capital ?markets? are now ?market fragments? ..and? ??Shareholder? has changed from ?growth? to ?income + performance? ?Higher search costs, higher capital costs and higher cost of capital

May 1, 2013

By John A. Kost

Control of the dust produced by continuous mining machines in coal mines is conventionally attained by water sprays from fixed nozzles mounted on the frame of the machine behind the cutting head. In the tests conducted under this contract a so-called "wet-head" machine was used, where the spray nozzles were mounted on the rotating head itself, close to the coal-cutting bits. The tests were conducted at the Robena Mine of U.S. Steel Corporation, using Lee-Norse machines. Operating the wet-head machine and a conventional spray machine in turns in the same section, it was found that the wet-head produced approximately 25 percent less respirable dust and 60 percent less total airborne dust than the conventional spray machine. The wet-head also greatly improved the visibility of the cutting bits from the machine operator's position. Several difficulties had to be overcome before any meaningful tests could be conducted, including excessive pressure drops in the piping system and plugging of the nozzles from internal water contamination. The major obstacle, however, was the rotating water seals on the wet-head, which leaked excessively after only a few hours of operation. Only after several changes and plant and laboratory tests was a design found which permitted conducting the underground tests without appreciable water leakage.

Jan 1, 1976

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By J. E. Coyne, L. E. Tanner, J. E. Boyd

In recent investigations of the isothermal transformations of the retained 0 phase in a titanium alloy having 13 pct V, 11 pct Cr, and 3 to 4 pct Al, there have been indications that the w transition phase is the initial decomposition product at temperatures below about 950°C (510 c).' This metastable phase, found in a number of titanium-base alloys rich in stabilizing elements and known to have an adverse effect on their ductility and toughness, is not easily observed by the usual experimental techniques. Since wis coherent with the /3 matrix,495 distinct interphase boundaries are not revealed metallographically. However, in some cases, an etching effect (i-e., a "mottled" /3 surface) poorly resolved by light microscopy has been found to correspond with the presence of w.6 X-ray diffraction examination has generally been the most suc- cessful means for identifying this phase and crys-tallographic determinations have been made.4'5 Dynamic elastic modulus7 and electrical resistivity measurementse have also aided in the identification of w. In the current study, the electron microscope was utilized to examine microstructures in aged Ti-13V-11Cr-3A1 that were unresolvable by light microscopy techniques. Using negative parlodion replicas (shadowed with chromium at 27 1/2 deg) examination was made of various transformation

Jan 1, 1962