Search Documents

By E T. Baker, J A. Resing, S L. Walker, V Ferrini, F Martinez, R Haymon

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Enumerating active sea floor hydrothermal sites has been a challenge since their discovery almost 40 years ago. High-temperature hydrothermal sites are readily discoverable, primarily by detecting mineral-laden plumes, but working at these sites poses severe environmental and operational difficulties. Low-temperature vent fields, which may represent waning of venting from high-temperature systems, may be more accessible but are more difficult to locate. Over the last decade, however, oxidation-reduction potential (ORP; aka Eh) sensors capable of detecting minute concentrations of reduced hydrothermal chemicals have been successfully used to pinpoint such fields. In this extended abstract, we use ORP anomalies observed during continuous (towed sensor) plume surveys to estimate site frequency along four intermediate- to fast-spreading ridge sections. From these data, we estimate site frequencies between five and 16/100 km for these ridge sections. Previous camera surveys on the fast-spreading East Pacific Rise support these frequencies. These rates are much greater than the frequency of ~0.5–5/100 km, generally increasing with spreading rate, derived from well-surveyed ridge sections in the InterRidge database (InterRidge, 2014). The higher frequencies arise because ORP sensors are able to distinguish between sites as close as ~1 km and identify sites with negligible or no optical plume signal.CITATION:Baker, E T, Resing, J A, Martinez, F, Haymon, R, Walker, S L and Ferrini, V, 2015. How leaky are oceanic ridge axes? A new assessment of the spatial density of submarine hydrothermal discharge, in Proceedings PACRIM 2015 Congress, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

This study examines the application of Landsat TM data to the identification of hydro- thermal alteration in the arid terrain of the El Salvador region of north Chile. Numerical reflectance values were extracted from the digital Landsat TM data for a variety of rock surfaces, including four parts of the El Salvador gossan, for each of six spectral bands. These reflectance values were analysed statistically in order to select the three spectral bands, combined as a colour composite image, that are most efficient in discriminating different varieties of alteration and for general geolog- ical interpretation. The most cost effective com- posite image for this area is a combination of bands 1,4 and 7 as the blue, green and red components respectively, with simple contrast enhancement. This image is superior to some much more expensive enhancement techniques and allows unambiguous identification of areas of hydrothermal alteration larger than about 50m. The display includes a practical guide to the use of Landsat TM imagery for volcanic gold Exploration.

Jan 1, 1987

By L. R. Fyffe, D. R. Lentz, S. H. Mcclenaghan

"Abstract - The Eel River area in the southwestern Miramichi terrane of New Brunswick contains a complete calc-alkaline suite of volcanic rocks that are interlayered with intervals of sedimentary and polylithic fragmental rocks, and are overlain by a thick sedimentary sequence. This package, collectively referred to as the Meductic Group, was deposited in a submerged volcanic arc setting interpreted to be part of the Popelogan arc. Rifting of this arc led to the development of the Tetagouche-Exploits back-arc basin, and formation of volcanogenic massive sulfide deposits in bimodal volcanic rocks of the Bathurst Mining Camp in the northeastern Miramichi Terrane. Unlike the Bathurst Mining Camp, volcanic rocks in the southeastern Miramichi Highlands form a continuous calc-alkaline suite characterized by increasing Zr/TiO2 with increasing SiO2, in part resulting from progressive coupled assimilation and fractional crystallization of nested magma systems. Slumping of semi-consolidated volcanic and sedimentary rocks in topographically unstable areas resulted in numerous slumps and debris flows that are preserved throughout the Eel River area. In the early 1990s, the discovery of a large sulfide clast in a road cut along the Benton road sparked interest in the volcanogenic massive sulfide potential of the Eel River area. Subsequent drilling intersected smaller fragments, one clast of which graded 16.7% Zn, 5.6% Pb, 90 ppm Ag, and 220 ppb Au. The intersection of thin lenses of stratiform sulfides in another drillhole indicates favorable conditions for the preservation of massive sulfides. Their subsequent incorporation into synvolcanic debris flows resulted in the transport and deposition of sulfide clasts from hydrothermal vents to more distal locations. Similar to the Buchans deposits of Newfoundland, tracing these debris flows back to their source would be beneficial from an exploration perspective. Approximately 15 km to the southwest of the Eel River area, gold-bearing base metal sulfide clasts (11.1% Zn, 6.13% Pb, 0.19% Cu, 108 ppm Ag, and 1100 ppb Au) occur within intermediate-composition volcanic rocks at Monument Brook in eastern Maine. Sommaire - Le secteur d’Eel River dans le sud-ouest de la terrane de Miramichi au Nouveau Brunswick contient une séquence complète de roches volcaniques calco-alcalines interstratifiées avec des roches sédimentaires et fragmentaires polylithologiques, sous une épaisse couverture sédimentaire. Cet assemblage constitue le Groupe de Meductic, et a été déposé dans un environnement d’arc insulaire interprété comme une partie de l’arc de Popelogan. Le rifting de cet arc à mené au développement du bassin d’arrière-arc de Tetagouche-Exploits, et à la formation de gisements de sulfures massifs volcanogènes dans les roches volcaniques bimodales du Camp Minier de Bathurst dans le nord-est de la terrane de Miramichi. Contrairement au Camp Minier de Bathurst, les roches volcaniques des hautes terres du sud-est de Miramichi constituent une suite calco-alcaline continue caractérisée par un accroissement du rapport Zr/TiO2 à des valeurs croissantes de SiO2, résultant en partie de l’assimilation progressive et de la cristallisation fractionnée de systèmes magmatiques superposés. L’effondrement de roches volcaniques et sédimentaires semi-consolidées dans des secteurs topographiquement instables est à l’origine des nombreux slumps et coulées de débris qui sont préservés dans le secteur d’Eel River. Au début des années 1990, la découverte d’un large claste de sulfures le long de la route Benton provoqué un intérêt pour le potentiel en gisements de sulfures massifs volcanogènes dans les secteur d’Eel River. Des forages ont par la suite recoupé des fragments plus petits, dont un claste qui a retourné des teneurs de 16.7% Zn, 5.6% Pb, 90 ppm Ag et 220 ppb Au. Le recoupement de minces lentilles de sulfures stratiformes dans un autre forage indique des conditions propices à la préservation des sulfures massifs."

Jan 1, 2006

By J. C. Nicholson

The "V" system was first introduced by the West Virginia Coal & Coke Company at their No. 9 mine, Norton. Norton is a small mining village on the B. & 0. railway, about seven miles from the town of Elkins. This year, accompanied by G. D. MacDougall, I visited this mine to obtain first-hand information regarding this modem system and to determine its adaptability to conditions in Nova Scotia. The following is a brief account of my observations. The seam that is being worked is known as the Lower Kittaning, which, at this point, has an average thickness of 7 feet. This includes a band of hard clay varying in thickness from 8 to 14 inches, which occurs about 2 feet from the pavement, also 8 inches of inferior coal at the roof. The latter is not recovered, which leaves to be mined about 5 1/2 feet of clean coal. The roof is slate and shale for the first 30 feet, followed by 40 to 60 feet of sandstone; the total cover is from 80 to 250 feet thick. The seam lies very flat, with a dip of only 2 per cent., and, as the dip is toward the main entrance, it' is in favor of the load, also providing natural drainage for any water the mine makes. As the mine is not gassy, and there is no water to be pumped out, one can understand that mining conditions are practically ideal.

Jan 1, 1924

By Bruce A. McKinstry

Introduction For many major mining projects the time frame from initial planning to production can be measured in decades. Hecla's Silver Shaft project, scheduled to go into production by the end of this year, includes a complete surface facility, shaft with an ultimate depth of 2.4 km (7,700 ft), complete ore pass and loading pocket system, and 610 m (2,000 ft) of development drifting and stope preparation. The project was conceived in the fall of 1979, and the duration of a mere four years from conceptual engineering to production is testimony to what can be accomplished when a mining company and a contractor work as a team rather than developing into two warring camps, as often happens. Engineering In 1979, Hecla Mining Co. awarded a contract to J. S. Redpath Corp. to perform feasibility investigations and design engineering related to a proposed new shaft facility at the Lucky Friday Mine. The Lucky Friday, in Mullan, ID, is a major producer of silver, as well as significant quantities of lead and some zinc. In late 1979, stoping was in prog-

Jan 10, 1983

By Robert A. Brown

"The O'Brien mine is in the west-central part of Cadillac township along the Cadillac 'break', which extends for 7,500 feet from west to east across the property.The ground was staked in 1924 by A. Dumont and W. Hermeston, prospecting for M. J. O'Brien, Limited. The first vein discovered is that now known as No. 1. The No. 4 vein was later exposed on the surface; the other veins known to be present were revealed by underground work and diamond drilling carried out both from the surface and underground.The mine is developed from three vertical shafts: No .. 2 extending from the surface to 2,000 feet; No. 3 from the surface to 1,500 feet; and No. 4 from 2,000 to 3,000 feet. There is on the property a mill of about 200 tons a day capacity, the usual shops, and a townsite housing about forty-five families. Gold production to the end of September, 1944, amounted to 295,824 fine oz. from ore having an average grade of 0.505 oz. a ton. In addition, the mill recovered 3,237 tons of arsenic trioxide having a purity of 83 per cent As2O3.GENERAL GEOLOGYThe four main groups of rocks of the Cadillac area- the Cadillac, Blake River, Kewagama or Pontiac, and Malartic- are found within the boundaries of the property. However, as these rocks have been fully described in · various government reports (1,2,3,4,5,6) and all the known orebodies occur within one group- the Blake River-a detailed description of the geology will be dispensed with here. The known ore deposits lie south of the Cadillac 'break' in a group of rocks that includes 'greenstones', greywackes, conglomerate, porphyries, and a rock of gabbroic composition that may be intrusive. Both flows and tuffs can be recognized in the 'greenstones'. The two bands of porphyry that trend easterly across most of the property have been considered by some observers to be dyke rocks and by others to be flows. Certain evidence points to their being dykes that were intruded as sills considerably prior to the emplacement of the gold-bearing veins, but the possibility of flow origin cannot be fully rejected. North of the talc-chlorite-carbonate schist zone forming the 'break' the rocks are conglomerate and greywacke with iron formation, in which there are no known veins of ore grade. Within the schist zone are minor acid and basic intrusives. The general trend of both bedding and schistosity is a few degrees south of east. The dip is generally vertica1 or steep to the south."

Jan 1, 1954

By K. Fuenkajorn, J. J. K. Daeme

Ring tension tests have been conducted on 229 mm (9 in) diameter disks of Grande basaltic andesite and Pomona basalt with various center hole sizes in order to study the relationship between ring tensile strength and relative hole radius (hole radius/disk radius). The tensile strength, [ ] decreases as the relative hole radius, [ ] increases. A power equation, [ ] where C and R represent the coefficients of strength and shape, respectively, adequately represents the ring tensile strength as a function of relative hole radius over the range investigated. This equation can be used to distinguish the effect of the hole size from the strength results, to predict the tensile strength of a ring sample containing arbitrary hole sizes, and to approximate the critical relative hole radius of the material tested.

Jan 1, 1986

By S. J. Matas, R. F. Hehemann

The existence of two distinct forms of bainite—upper and lower bainite—in hypoeutectoid steels is confirmed by a systematic study of the structure of the product resulting from this mode of austenite decomposition. The transition between these two forms occurs at about 650° F regardless of the alloy content of the steel and their structural differences can be interpreted in terms of the kinetics of carbide precipitation from supersaturated ferrite. In the past few years, a renewed interest has been displayed in the kinetics and mechanism of the bainite reaction in steels. Several rather divergent models for the transformation mechanism have evolved from these studies,'-' however, it is difficult to evaluate these models critically on the basis of the existing experimental data. In particular, a more detailed knowledge of the structure of bainite should be helpful in providing a framework for the construction of an appropriate model. Metallographic studies7-l4 have led to a recognition of at least two distinct forms of bainite—frequently termed upper and lower bainite. Although the morphology of bainite changes with reaction tem- perature, there appears to be a relatively sharp transition between the two forms. This occurs in a narrow temperature range near 650° F. Transformation at temperatures below about 650° F results in the presence within the bainite of small plates of carbides oriented at an angle of 60 deg with respect to the direction of growth of the plate, while at higher temperatures carbides are oriented parallel to the growth direction. There is no generally accepted view regarding the significance of this structural transition. Some authors feel that carbides precipitate from austenite at all reaction temperatures1' while others claim, at least for low-temperature bainite, that carbides precipitate from supersaturated ferrite.14.15 It was recognized many years ago that the nature of the carbide in bainite depends on the reaction temperature. The carbide hase in upper bainite is unmistakenly cementite.16-19 The exact nature of the carbide in low-temperature bainite is less certain. Magnetic measurements of lower bainite reveal no cementite Curie point21'22 and dilatometric studiesz0 produce total expansions which are larger than those predicted on the basis of a ferrite-plus cementite structure. These effects have been attributed to the

Jan 1, 1962

By A. F. Otero

During the electrowinning (EW) of copper significant quantities of highly toxic vapors (acid mist) are produced due to the liberation of oxygen at the cathodes. Acid mist affects the health of operators, the environment and plant infrastructure. Acid mist can be decreased to acceptable levels by a combination of physical means (e.g. ventilation, plastic spheres over electrolyte) and chemical surfactants that decrease the surface tension of the electrolyte, modifying the way oxygen bubbles burst at the surface of the electrolyte. However, only few chemical surfactants are compatible with electrolytic applications, and they are not always used due to their high costs. This paper describes the application of a novel surfactant of natural origin (commercial name Mistop®) to suppress acid mist in copper EW process. Mistop® contains triterpenic saponins derived from the Chilean quillaja tree Quillaja saponaria Molina. The product is non-toxic, and poses no risks to the environment or to EW operators. Mistop® was tested at a laboratory, pilot plant and industrial scale in the world?s largest copper EW production plant at Radomiro Tomic (RT), CODELCO, Chile. At a Mistop® dosage of 8-9 ppm, acid mist decreased below the value accepted by Chilean regulations (< 0.5 mg/m3). At this dosage, Mistop® represents and economical alternative to chemical surfactants, and it is currently industrially used at RT.

Jan 1, 2003

By W. Rostoker, R. P. Elliott, B. W. Levinger

Phase equilibria in the Ti-Mn-Mo system have been investigated in the composition range 100 to 60 pct Ti and in the temperature range 550 to 1150°C. Three out of ten isothermal sections are presented as well as seven vertical sections, projections of the beta space and the surface of incipient melting. A STUDY of the system Ti-Mn-Mo was undertaken as part of a program to aid in the development of titanium-base phase equilibrium diagrams of potential technical importance to alloy development. The scope of the investigation included the composition range 100 to 60 wt pct Ti (all compositions refer to weight percentages) and the temperature range 550" to 1150°C. A surface of incipient melting was constructed from measurements of a large number of alloys. In the binary system Ti-Mo,&apos; the high temperature modification of titanium generally spoken of as the p phase is stabilized to successively lower temperatures with increasing alloy content. There are no known intermediate phases, and complete miscibility exists between body-centered cubic titanium and molybdenum. The u solid solution is limited to less than 0.8 pct Mo at temperatures between 885" and 600°C. An equilibrium diagram for the binary system Ti-Mn has been published.&apos; Manganese behaves as a p stabilizer but undergoes a eutectoid transformation at about 20 pct Mn and 550°C to a plus an intermediate phase. The structure of this phase has been found to be isomorphous with the a phase FeCr." Accordingly, the phase is assigned the formula TiMn, although its actual location on the composition scale has not been determined and may well be not exactly at the equiatomic composition. In disagreement with ref. 2, the origin of the TiMn phase has been shown&apos; to be a peritectoid transformation at a temperature between 900" and 1000°C. A second intermediate phase occurs at the atomic proportions TiMn,. The structure of this phase was originally established by Wallbaum" as having a hexagonal lattice (C 14 type, 12 atoms per unit cell) isomorphous with MgZn,. In this work, the structure determination was confirmed and lattice parameters determined to be: a = 4.815 kX, c - 7.901 kX. Because of the extensive range of the P phase, the ternary system was suited to the determination of the phase boundaries by the parametric method of Andersen and Jette." During the course of the investigation, this method was found applicable only to the P/a+P boundaries but not to P/P+ compound boundaries. Metallographic methods were used alternatively for delineating these phase boundaries. Preparation and Treatment of Alloys Over 70 alloys were prepared for the study of this system. Ten gram alloy buttons were arc melted in a nonconsumable electrode furnace using inert atmosphere protection, and a water cooled copper crucible. The construction and operation of this type of melting unit has been described.&apos; To insure complete solution of alloy additions, especially molybdenum, the buttons were remelted alternately on top or bottom as many as five times. This was accomplished by a suitable mechanism for "flipping" the ingots over. It was very difficult to obtain homogeneous melts in the region of less than 75 pct Ti because of the very high melting point of molybdenum and Ti-Mo master alloys and the comparatively low boiling point of manganese. Thus, the arc conditions for insuring complete solution of molybdenum were incompatible with the prevention of heavy losses of

Jan 1, 1955

By A. H. Bell

DEEPEST hole in the earth, and deepest producing oil well in the world-such is well No. K.C.L. A-2, of the Continental. Oil Co., completed on April 12 in the San Joaquin valley about four miles west of Wasco, Calif. It penetrated the earth&apos;s crust to a depth of 15,004 ft.- almost three miles-a depth that exceeds by over 2200 ft. that of the previous record holder in western Texas. It is now producing oil from sands at a depth from 13,092 to 13,- 175 ft., which is about 1500 ft. deeper than the record formerly achieved in Louisiana. Continental&apos;s new well was bottomed in what is possibly Domengine-Avenal Eocene sand, and is producing from the Middle Miocene equivalent to the Rio Bravo sand.

Jan 1, 1938

By E Christodoulou, L Zoumpoulakis

The kinetics of the thermal decomposition of MgCO3 was investigated using isothermal experiments performed in a thermogravimetric analyzer under a nitrogen atmosphere at 380¦, 400¦, 450¦ and 480¦C. The weight loss data as a function of time were modified to give the fraction that reacted (ß) and the rate of reaction (dß/dt) vs. time (t). Kinetic analysis of the experimental results, using three different methods, showed that diffusion predominates the MgCO3 decomposition over the investigated temperature range, with the data being best fitted by JanderÆs equation ([1&#8722;(1&#8722;ß)1/3]2=kt). The activation energy was estimated by Arrhenius plots using both the initial reaction rates and rate constants from fitting the above equation. The values estimated were 27.1 and 171.4 kJ/mol respectively.

Jan 1, 2001

By Grażyna Dzik, Adam Mirek, Krzysztof Król

The Upper Silesian Coal Basin is located in the area of the Upper Silesian Syncline and belongs to one of the most complex tectonic units in Europe. It occupies 5,650 km2. In 2020, there were 20 hard coal mines operating in the area. Seismological research in this area consists of observation of precursors/symptoms of shock generation and understanding of their effects. Studies (Teisseyre R. 1972, Mutke G. & Stec K. 1997, Stec K. 2007, Dubiński J. & other 2010, Idziak A. 2010) of complex impacts of rock mass provided a background for determining the conditions for the formation of exploitation and regional seismic shocks. Issues related to tectonic and exploitation stresses, successive extraction of coal seams at higher depths, operation in the vicinity of fault zones, often complex geological and organic conditions result in the activation of a discontinuity surface due to stress caused by deformation of rock layers, which, as a result, causes the emergence of strong shocks above 107 J. The article was based on analyses of extraction value, high-energy shocks, both of mining and tectonic-mining (so-called regional shocks) origin, against the background of changing operating conditions, which, as a result, creates an image of periodically changing seismic activity and location of strong shocks. Observation results show that, with an increase in exploitation depth and declining extraction, the number of strong shocks caused by tectonic stress (107 - 109 J) and exploitation stress (≥105 J) has been steadily increasing over the last 25 years.

Apr 26, 2022

1. Books from Elsevier The folowing are available from Elsevier Applied Science, Crown House, Linton Road, Barking, Essex IGl 8JO, OK. . Driling wastes, edited by F.R. Engelhardt, J.P. Ray, and A.H. Gilam. 1989. 872 pp. £95. Geothermal resources, by R. Bowen. 2nd ed. 1989. 468 pp. £60. The fate and efects of oil in freshwater, edited by J. Green and M.W. Tret. 1989. 340 pp. £42. Mining and the freshwater environment, by Martyn Kely (with contributions by W.J. Alison, A.R. Garman, and C.J. Symon). 1988. 228 pp. £32. 2. Books produced by Metal Buletin The folowing are available from Metal Buletin PLC, Park House, Park Terace, Worcester Park, Surey KT47HY, England. Prices and data 1990. £41 (airmail). Foundry directory and register of forges 1989-1990. £52 (airmail). 2. Canadian Publications The folowing two publications are available from the Canadian Government Publishing Centre, Supply and Services Canada, Otawa, Canada KIA 059. Mining and mineral processing operations in Canada. Mineral Buletin MR 224. $23.70. Canadian minerals yearbook 1989. Review and outlook. Mineral Report 38. $47.95. Technology developments The Mintek Pyrosim Simulator Pyrosim is a computer program for the steady-state simulation of pyrometalurgical processes?.

Jan 1, 1990

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth&apos;s surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer&apos;s airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist&apos;s artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth&apos;s surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer&apos;s airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist&apos;s artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By F. S. Buffington, Morris Cohen

THERE is little quantitative information available concerning the effect of applied stress, in both the elastic and plastic ranges, on diffusion kinetics. Accordingly, a program has been undertaken to determine the rate of self-diffusion in high purity iron, with the specimens subjected to stress during the course of diffusion. Results are reported here for body-centered cubic iron at a diffusion temperature of 890°C. The iron used was 99.97 pct Fe, the principal impurities being 0.002 pct C, 0.008 pct 0, and 0.02 pct Si. The surface-decrease method of self-diffusion analysis was employed, and Fe55 Mn x-radiation, 2.9 years half-life) was the tracer element. Details of specimen preparation and equipment are given elsewhere.&apos; Disks of the high purity iron, % in. diam x 1/4 in. thick, were annealed at 890°C for 18 hr in dry hydrogen to produce large grains of a ferrite. The faces of the disks were then surface ground, and possible grinding stresses were relieved by annealing at 890 °C for 45 min in vacuum. A layer of radioactive iron 0.00186 cm thick was electroplated on one face of each disk. The self-diffusion coefficient was calculated from the ratio of the radiation intensities emanating from each of these faces, as measured before and after diffusion.&apos; The heating was carried out in a vacuum furnace (10-5 mm Hg) controlled to ±1.5°C. The specimens were loaded in compression between two quartz disks during the diffusion runs by means of a lever system operating through a vacuum seal. Thus one quartz disk was pressed directly against the radioactive face of the specimen, minimizing the vapor loss of radioactive iron. Steady-state creep occurred in all instances where permanent deformation could be detected, but the specimens did not exhibit appreciable transverse barreling until natural strains of 0.2 to 0.3 were attained. Essentially, the diffusion took place under uniaxial stress. The plastic strain in each case was obtained at the diffusion zone by measuring the diameter d there before and after the run: e = 2 In — do Let Du equal the self-diffusion coefficient which would have prevailed at the given temperature if no stress had been applied. This was calculated from the temperature-dependence equation which had been previously determined: —59,800 D, = 6.2 exp ( I sq cm per sec* [I]

Jan 1, 1953

By Harold J. Schock

This paper describes an experimental method for the monitoring of diesel-generated exhaust gas pollutants in a dead-ended drift for the purpose of assessing the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 105 ft. (32.0 mf long and slightly downsloping, with an average height and width of 8 ft. (2.4 m) and 28 ft. (8.5 m1 , respectively. The data were gathered for assessing these ventilation methods and for gathering data to support a computer model of the dispersion and mixing processes. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generated pollutants. Induction ventilation appeared to be the least effective of the three methods examined. A comparison was also made between personal monitoring and area monitoring. Results of this analysis showed that in regions of high concentration gradients, it was not possible to get good agreement between point sampling and personal monitoring. In well-mixed areas, good agreement between the two methods of monitoring was obtained.

Jan 1, 1980

By N. N. Breyer, W. R. Warke, S. Dinda

A model for the low-temperature peak, LTP, in fcc metals is presented. In high stacking fault energy metals, e.g., aluminum and nickel, it is proposed that a reversible dislocation glide and climb process might give rise to the observed high relaxation strengths and activation energies equivalent to volume self-diffusion values. In low stacking fault energy metals such as copper, gold, and silver, dislocation climb is energetically unfavorable at T < 0.5 Tm and the relaxation process is therefore mainly one of reversible glide. This model is used to explain the effect of a change in grain size and impurities on the LTP. THE low-temperature grain boundary damping peak, LTP, in spectroscopically pure aluminum,&apos; copper,17&apos; gold,2 nickel,3 and silver4 has recently been the subject of a detailed investigation by our laboratory. The main results are summarized in Table I. An empirical relationship was found between the peak relaxation strength, AE, and the width of the dissociated dislocation, do,* given by: do = µa2/24p? (Ref. 5) [I] where p is the shear modulus, y is the stacking fault energy,6-8 and a is the lattice parameter, Table 11. 4E is plotted against do in Fig. 1. Two regions are apparent: region (a)! which contains all but one of the metals, where AE decreases linearly with increasing do, i.e,, AE 1/do; and region (b), where ?E is approximately independent of do. A similar trend is observed when the ratio Qp/QL is plotted as a function of do, Fig. 2. (Qp and Ql are the activation energies for the peak and for lattice diffusion, respectively). In the past, when Qp and QL were found to be comparable, the relaxation peak was explained in terms of grain boundary sliding.10 The equivalence of Q, and Qb. the activation energy for grain boundary diffusion, prompted the suggestion that it was a consequence of reversible grain boundary migration on an atomic scale." A new model for the LTP, which is based on the experimental relationships in Figs. 1 and 2, is presented. In region (a) it is suggested that stress relaxation occurs through the reversible glide and climb of grain boundary dislocations; in region (b) only reversible glide can take place. The resultant effect on the grain boundary might be sliding or "a bowing out", but, since the total distance moved will be 50A, the atomic movements are considered of primary im- portance. It must be emphasized that this is only a qualitative model, but at the moment it appears the most likely way to explain the widely varying, but re-

Jan 1, 1969

By J. E. Tupper

"This paper will discuss strategies for the introduction of computer technology in the mine environment. More specifically, it will focus on issues such as: (a) make or buy; (b) programmer less mines; and (c) support from corporate groups.The paper relates these strategies to systems for mine operations. These will be illustrated by considering the implementation of some phases of these systems at Teck Corporation.IntroductionThis presentation addresses some of the major considerations in a strategy for mine computerization and then relates these considerations to the computerization cycle and Teck Corporation.Strategy is defined as a conceptual framework or plan to accomplish a goal. For purposes of this paper, the goals can be more simply defined for operational purposes as either increasing revenue or decreasing costs.The strategy will allow us the framework for measuring tactical decisions such as computer and software acquisitions.The Mine Life CycleTo start with, let us look at the mine life cycle from a computer systems point of view:-Exploration-Property Development-Feasibility-Construction-OperationFrom a systems point of view, the exploration cycle is oriented to geophysical and geochemical computing. Property development starts with drilling and building the geological data base. The feasibility cycle includes all stages of evaluating the decision to proceed with mine development: ore reserve calculations; mine planning; and financial projections. Construction includes project management and project accounting systems. Systems required for operation are those needed by personnel at the mine site."

Jan 1, 1982