Search Documents

By Nelson Collao I.

Loss of the organic phase from solvent extraction circuits is a major cost factor for SXEW operations. Recognized sources of loss include evaporation, entrainment, and biological degradation. The mechanisms for both entrainment and evaporative losses are well recognized. Biological degradation of the organic has not been as extensively evaluated as the other mechanisms but is a major source of loss. This paper discusses the impact of biological degradation on an operating plant, potential mechanisms for degradation, conditions under which biodegradation of plant organic can occur and plant conditions that may assist in promoting biodegradation.

Jan 1, 2003

By Takeshi Azakami

By combining the iron reduction process with the usual rotary kiln process, the direct production of metallic zinc from EAF dust is proposed. After thermodynamic estimation and desk-top experiments it is confirmed that the process is hopeful under suitable conditions. In order to get some practical test data the enlargement of the process scale was planned and the bench scale tests were carried on successfully. In these experiments a zinc ingot of PW grade was produced from EAF dust.

Jan 1, 2003

By Minjun Tang, Jianfeng Zhou, Linjiang Qing, Yufeng Guo, Tao Jiang

"For the comprehensive recovery ofV, Ti, Fe in vanadium-titanium magnetite in the process of pre-reduction-electric furnace smelting, it is expected that vanadium oxide is reduced into molten iron and titanium oxide is available in the slag. Thus the effect of slag basicity, the content of MgO, MnO and CaF 2 of slag content on the separation of slag and molten iron and the comprehensive recovery of V, Ti, Fe were investigated. The results show that increasing slag basicity, MgO, MnO and CaF2 are all beneficial to the separation of slag and molten iron. Higher slag basicity and the addition of CaF2 strengthen the reduction of vanadium oxide, and inhibite the reduction of titanium oxide, which are in favour of the recovery ofV and Ti. However, the addition ofMgO, MnO was not efficient for the comprehensive recovery ofV, Ti, Fe. For the vanadium-titanium magnetite of Panxi in China, the recovery of Fe was over 98%, the recovery ofV in molten iron was over 85% and the Ti02 content in slag was about 43% under the optimal conditions of slag phase type.IntroductionIt is well known that there are abundant vanadium-titanium magnetite resources which are located in Panzhihua of Sichuan Province[!]. At present the vananium-titanium magnetite concentrates are smelted in the blast furnace, which just make use of iron and vanadium, but lots of titanium is discarded in the slag. At the same time, the process has a large number of disadvantages, such as low recovery of vanadium, long route, pollutions, large investment and expenditure of energy[2-3]. In recent years, in order to efficiently utilize the vanadium-titanium magnetite concentrates, several new non-blast furnace processes have been proposed, such as pre-reduction-electric furnace, pre-reduction-grinding separation and so on[4]. Especially pre-reduction-electric furnace is operating well in South Africa and New Zealand,However,Du to the high slag basicity of the slag, the grade ofTi02 of slag is Corresponding author:Minjun Tang.E-mail:450435123@qq.com. Tel:13627429224."

Jan 1, 2013

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature' in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By Patricio Barrios

This paper discusses the revamp and expansion of Atlantic Copper's (formerly Rio Tinto Metal) copper smelter located at Huelva, Spain. The plant was expanded from 150,000 to 270,000 tpy new copper in anodes, and from 133,000 to 215,000 tpy cathodes. Lurgi successfully executed this contract on a lump-sum, turnkey basis in just 19 months. The Lurgi on-site task force performed this work in close cooperation with Atlantic Copper's personnel, with a minimum of disruption in the plant's ongoing operation. The contractual performance parameters were achieved to the client's satisfaction shortly after the mechanical completion of the respective plant sections.

Jan 1, 1998

By Yuanbo Zhang, FENG ZHOU, Guanghui Li, Zhengwei Yu, RuijunWang, Tao Jiang

Composite agglomeration process (CAP) of iron ore fines has been proved an effective route for ironmaking burden production, and is characterized by low the fuel consumption and high the productivity compared with the traditional sintering process. Sintering behavior of pelletizing feed in CAP has not been studied fully yet. In this study, individual pellet and simulated CAP cells were roasted under the simulated sintering conditions. The compressive strength, FeO content and microstructures of roasted samples were investigated. The results show that pelletizing feed either from magnetite ore hematite concentrate can be indurated under the conditions of conventional iron ore sintering. Hematite pelletizing feed has better sintering property than magnetite pelletizing feed. Pelletizing feed consolidation in CAP cells is identical to the individual pelletizing feed, but the strength of CAP cells is much higher than the individual pelletizing feed. Higher basicity in both pelletizing feed and matrix feed is beneficial to the strength of CAP cells. Individual strength of pelletizing feed is not the decisive factor in CAP as the pelletizing feed has been embedded into the matrix with high basicity and formed an organic whole. The main chemical compositions and basicity of pelletizing feed and basicity matching with matrix feed is important.

Jan 1, 2015

By Neale R. Neelameggham, Brian R. Davis

Organic agriculture is using natural materials such as degrading plant matter to replenish soils. This includes use of naturally degraded plant components such as peat, humus and weathered brown coals. Another important natural organic matter which has not been applied in agriculture thus far has been the black coal, Here we show that reversing the coal formation reaction by combined hydro-oxidation principles of biochemical engineering in natural conversion methods in an accelerated fashion. The modified coal soil additive can convert arid lands into farm lands for the future to sustain the population growth. In addition, the development of this new use of black coal will revive economically deprived areas from phasing out coal in the USA and Europe. This will show how the Stored energy in coal can be made renewable in helping plant growth under the soil to facilitate above ground photosynthesis.

Mar 1, 2018

By Sarel Johannes Francois Gates, Ida Kero, Yan Ma, Gabriella Tranell

During the tapping and casting of manganese ferroalloys, fumes are generated and released to the working environment. The fumes are mostly composed of metallic oxides generated due to reaction between high temperature molten metal and ambient oxygen in the air. From an environment perspective, it is important to limit these emissions. However, to do so, it is important to understand fuming mechanisms and kinetics as well as fume compositions, i.e. element behavior during the oxidation process of liquid manganese ferroalloys. Silicomanganese alloys are composed of aminimum of 65 wt% Mn and 17 wt% Si, 2 wt% C as well as minor and trace elements. These elements include Fe, Mg, Al and other elements originating from ores and reductants. Trace elements behavior in fume from liquid silicomanganese generated under an impinging air jet in the temperature range of 1450–1700 °C has been investigated in this work. The thermodynamic and kinetic conditions governing the generation mechanisms are discussed.

Mar 1, 2017

By Dao Su, Kelang Mu, Yufeng Guo, Jinghua Zeng, Tao Jiang

"The influence of high pressure roller grinding (HPRG) on sintering of iron concentrate fines was investigated. Results of mini-sintering tests showed that assimilation temperature of iron concentrate fines decreased from 1230 ? to 1220 ? and assimilation time was shortened from 10 min to 5 min when the iron concentrate fines was pretreated by HPRG. Sinter pot tests showed that the yield of sinter increased from 60.33% to 72.92% , tumble index increased from 44.35% to 46.66%. The investigation indicated that, after being pretreated by HPRG, iron concentrate fines are improved in ballability and the fraction of fine particles increased, resulting in the improvement of granulation property and reactiveness in solid state reaction. As a result, sintering of iron concentrate fines were strengthened.IntroductionWith the rapid development of iron and steel industry and the decrease of high-grade ores, the imports of iron ore are increasing continually. It is of immensely strategic importance for development of iron and steel industry and energy security in our country to make good use of iron concentrate fine which is low price, high grade and has a refractory sintering property. When iron concentrate fine is used in sintering, granulation property of sinter mixture and permeability of sinter bed get poor. As a result, yield and quality of sinter fall down. Many researches show that, when HPRG is used in pelletization, quality of pellets is improved dramatically. Meanwhile, HPRG has a low energy consume, a large handing capacity and it is benefit for environment protect. At this theme, strengthening of sintering of iron concentrate fine pretreated by HPRG was investigated in this paper."

Jan 1, 2012

By Petr Sulovsky, Pavel Leber, Jaroslava Ledererova, Miroslav Svoboda

"The properties of raw materials used for the production of building materials play an essential role in their choice. Industrial waste materials can in some cases improve the performance of new building materials, when compared with classical raw materials. The addition of waste can however negatively impact some of the building material´s characteristics, influencing its stability, service time, durability, and can introduce undesirable variation of certain characteristics over time. It is necessary that each secondary raw material intended for such use be thoroughly investigated in terms of its chemical, physical, and mechanical properties, with special attention paid to the risk components and risk parameters. It is necessary to make many- sided technological tests in relation to the required characteristics of the resulting materials for each chosen application. Moreover, the limit values for the critical (risk) parameters, which the given secondary raw material must satisfy to be used in a specific technology, need to be defined. Introduction The risk components in the industrial waste materials to be used in the production of building materials fall into two groups: - components that pose a risk of development (instant or delayed) of a process deleterious to the utility properties and durability of the resulting materials. Such processes include volume change (expansion as well as shrinkage), alkali-silica reaction, delayed ettringite formation, thaumassite attack, aggressive carbonation, etc. - elements or components that can, if released from the waste-containing building material, pollute the environment. They involve the so called potentially hazardous elements as well as compounds like fenols, PCB, PAHs etc. From the viewpoint of the presence of both groups of risk components, the wastes can be classified as: • environmentally inert waste materials. They are produced in the largest volumes and do not pose a threat to human health. Their physical and/or chemical characteristics fail to satisfy all requirements for utilization in ordinary production. The aim of technology design is to work them into the building products with suitable utility properties. • easier workable waste materials containing toxic components are produced in large volumes. In spite of the content of toxic components, their physical and chemical properties make them suitable for ordinary production, provided that the harmful substances are immobilized by the chosen technology."

Jan 1, 2008

By T. W. Turk

In May 1984, Davy McKee Corporation was awarded a contract for engineering design, procurement assistance, project management and startup services for two gold recovery plants? in the People's, Republic of China (PRC). The basic design of these two projects was to be accomplished by a combined effort of the Chinese and Davy McKee Corporation (DMC). The, design goals were to provide a state-of-the art plant while maintaining Chinese standards and design practices whenever possible. Chinese-manufactured equipment was to be used as much as possible. This paper discusses the project organization and procedures developed to accomplish the design goals, the process selection and design, and the selection and procurement of equipment outside of the PRC. Design development for grinding, leaching and carbon adsorption, and gold recovery are discussed in detail. The major goal of process selection and design was to provide common criteria for both plants. Equipment .sizing and selection was identical for carbon-in-leach adsorption, gold recovery, acid washing, and carboo regeneration for both plants. Of special importance is the design of the wastewater treatment system. Due to the cl0se proximity of a major population area, slurry discharging from these mines must be treated to meet drinking water standards. The process development and design of this system is also discussed in detail.

Jan 1, 1989

By Xueqin Li, Xuewei Lv, Yu Zhang, Wenchao He

In recent years, a new process of “direct reduction-electric furnace smelting separation” has been put forward and developed for recovering the iron, vanadium, titanium and chromium to make full use of the chromium-bearing vanadium titanium magnetite. In the present work, FactSage, one of the most frequently-used thermodynamic calculation software, was used to calculate the migration of Fe, V, Cr and Ti with different nC/nO (mole ratio of carbon and oxygen). The calculation results indicate that the recoveries of Fe, V and Cr increase with increasing nC/nO and temperature respectively. In addition, the recoveries of Fe, V and Cr are up to 90% when the nC/nO value is more than 1.15.

Mar 1, 2018

By Wen-Ming Chien

Low temperature X-ray diffraction and thermal property studies of the solid-solid state phase transition for the polyalcohols (pentaerythritol (PE), pentaglycerine (PG) and neopentylglycol (NPG)) thermal energy storage solid solutions have been investigated by using X-ray diffractometry and differential scanning calorimetry (DSC) methods. X-ray diffraction studies on polyalcohols solid solutions, PE-NPG and PG-NPG, are from ?10oC to 50oC. XRD results shows the + mixed phase at the related low temperature (?10oC) for both PE-NPG and PG-NPG solid solutions. At high temperature range, XRD results show phase for PG-NPG solid solution and + mixed phase for PE-NPG solid solution. There are only two Bragg peaks, (111) and (200), shown in phase XRD patterns. The polyalcohols solid solutions have been cycled 5 times between -20oC to 100oC at different DSC scan rates to study the phase transition properties. DSC results of both PE-NPG and PG-NPG solid solutions show that the solid-solid state phase transition is near room temperature. Details of low temperature phase transition XRD and DSC results of PE-NPG and PG-NPG solid solutions will be presented

Jan 1, 2006

By Gen Kamimura, Hiroyuki Matsuura

Zinc is widely used for galvanization of steel plates due to its high corrosion resistance. Steel scraps containing waste zinc-coated steel plates are remelted for recycling of steel in electric arc furnace (EAF) process, in which zinc is concentrated in EAF dust ranging from 10 to 40 mass%. Therefore, recycling of zinc from EAF dust is important to secure zinc resource. Our group has proposed selective chlorination and evaporation method recovering zinc as a form of chloride from EAF dust. Since recovered zinc chloride may contain lead, iron and copper as impurities, purification of zinc chloride is essential for production of highly pure metallic zinc. In the present study, removal of lead chloride from molten zinc chloride-alkali chloride by cementation reaction adding zinc was investigated. Experimental results were analyzed and discussed thermodynamically and kinetically as well as the feasibility and limitation of this process were examined.

Mar 1, 2018

By T. Scarazzato, J. M. S. Jesus, D. C. R. Espinosa, J. A. S. Tenório

The development of separation process for the wastewater treatment in distinct industrial process have been applied for recover water and inputs. Electrodialysis is an example of separation process that have been studied for electroplating wastewater treatment. The use of ion-exchange membranes and an electric energy allows the selectivity separation of ions in a solution. The 1-hydroxyethane-1,1diphosphonic acid HEDP is an organic acid that is has been applied for the cyanide substitution in electroplating baths, and in this condition the electrodialysis has showed recover potential. The ion-exchange membrane used in an electrodialysis process contain organic sample are exposed for extreme conditions. These conditions can provide degradation structure and loss of permselectivity, which causes unusual membrane properties. The aim of this study is evaluate the influence of CuHEDP complexes in synthetic ion-exchange membranes using electrochemical test.

Mar 1, 2017

Kosaka Smelter & Refinery has a history of more than a century as a metallurgical department belonging to Kosaka mine. It has treated for a long time the "Black Ore" or the complicated concentrates dressed from it. The "Black Ore" is composed of black sulfides. It contains not only valuable metals such as gold, silver, copper, lead and zinc but also some impurities like arsenic, antimony and bismuth. With the development of Kosaka's floatation technology, five kinds of concentrates (copper, zinc, lead, pyrite and barite) have been separated from the "Black Ore" but the separation was not complete and each concentrate contained some unfavorable impuritie. In 1980s the highly appreciated yen and the drop of the metals priees forced many domestic mines to close their operations. Since then Kosaka Smelter has changed its way of operation to a custom smelter. Now more than 95% of copper concentrates are imported to take advantage of this technology of "Black Ore" treatment. It mainly treats the raw materials that contain high gold and silver like the "Black Ore". Recently, Kosaka has been working on the recycling of the metals from the printed circuit board scraps and sludge which contain some precious metals. The volume of the recycled metal is continuously increasing.

Jan 1, 2003

By John Jiang, Yeonuk Choi, Olivia Wang, Gus Van Weert

"As part of a general review of processing double refractory ores through Barrick Gold's autoclaves/CIL facility at Goldstrike, Nevada, blanking the gold cyanide adsorbing native carbon in the ore with hard (m.p. >55°C) paraffin wax was proposed. To avoid interference from other ore constituents in the exploratory testwork, commercial activated carbon was substituted for native carbon in the ore to establish the best conditions for de-activation of carbon with molten wax.IntroductionDouble refractory gold ores present two barriers to gold extraction. The first is generally a physical barrier: the gold is encapsulated or dispersed in a matrix which is impervious to the gold lixiviant. In most cases, including the Goldstrike deposit, this involves a pyrite or arsenopyrite matrix, although minor gold may also be dispersed in competent silica (quartz) or iron oxides. Gold can be rendered accessible by oxidative destruction of such sulphide matrices. At Goldstrike this is practised by roasting and autoclave oxidation (POX). It is the latter route to which this paper refers.The second barrier refers more correctly to gold recovery. Gold may be extracted from the autoclave oxidized solids with cyanide, forming a gold cyanide complex. One characteristic of this complex is that it adsorbs on graphitic surfaces. This behaviour is used advantageously on a large scale by gold millers, who use man made activated carbon particles to remove the gold from solution during leaching: the Carbon-In-Leach, or CIL process. The gold bearing carbon particles are larger than the ore solids and can be separately recovered by screening. Goldstrike uses the CIL technology to recover gold after autoclave oxidation."

Jan 1, 2012

By Matthias Schnitzler, Herbert Pfeifer, Ralf Bolling

"To transform metals high temperatures are usually needed. A fast and efficient heating can reduce the C02 emitted. The fastest way to heat metals is called direct flame impingement (DFI). The flame impinges upon the item being heated. For this method it is important to know the shape and length of the flame. Laser-induced fluorescence (LIF) technology allows measurements of a two-dimensional field without influencing the reaction or the flow. Commonly used is the measurement of OH-radicals, an indicator of the reaction zone.In the presented study measurements of a turbulent diffusion flame are shown. The position of the reaction zone and the influence of the distance between the item being heated and the burner are investigated. Conventional measurements and LIP-measurements are compared and the potential of DFI to increase the efficiency of heating metals is discussed.IntroductionDuring industrial heating processes a fast and efficient heating technology is required. Two important aspects are the NOx emission and the energy efficiency. The direct flame impingement (DFI) technology has the highest heat transfer rate possible with a gas/air flame. The turbulent high velocity flame jet impinges upon the item being is heated [ 1]. Due to the high heat transfer rate furnace and exhaust gas temperatures are lower. Therefore the energy efficiency is increased and the amount of NOx emitted is reduced.Hydroxyl- (OH-) radicals are an intermediate product that is generated during the combustion of hydrocarbons [2]. They are commonly considered as an indicator for the reaction zone and position of heat release. Figure 1 shows the hydroxyl-mole fraction in dependence of the distance along the gas flow. The figure clearly shows how fast the OH-concentration increases in the reaction zone. Figure 1 also shows that OH-radicals are present in the post combustion region, however in smaller concentration [3].The laser-induced fluorescence technology serves to measure the spatial distribution of OH-radicals in a two dimensional cross-section area of the flame. Therefore the flame dimensions and location can be determined with high spatial resolution without influencing the flow or the reaction [ 4,5]."

Jan 1, 2012

By Stephen Northey, Nawshad Haque, Terry Norgate

"Life cycle assessment (LCA) is a recognized tool to evaluate various processing routes for metal production. Declining ore grades and higher specific energy requirements for primary metal production put greater emphasis on recycling. Greenhouse gas (GHG) emissions of steel and aluminium metal production were quantified with recycling scenarios using material recovery facility (MRF) data from the database of SimaPro LCA software. The GHG footprint of the MRF is relatively minor compared with that of associated transport during collection (i.e. 10 times more than MRF) of curbside recyclable material. Additionally, if the bulk recyclable material is sent overseas (i.e. Australia to China) from the MRF for further processing, the GHG footprint of shipping can significantly be larger compared with the sum of the collection and MRF (assuming electricity is from same source). Thus opportunities exist for reducing GHG emissions from secondary metal production if it is processed close to the MRF.IntroductionIt is a challenge to recycle metals significantly, although theoretically infinite recycling is possible due to their elemental nature. Leaks from the metal stocks in society occur through corrosion, wear and dispersive uses, or via land filling or similar activities that return metals to the earth. In order to provide a technically sound and transparent assessment of metal recycling, a methodology such as life cycle assessment (LCA) should be used. By taking a life cycle perspective, the beneficial recycling properties of metals can be evaluated in a manner that enables appropriate comparisons with other materials or product systems that do not have recycling loops. In practice, mixtures of primary and secondary metals are often used in new products, and also at the end-of-life various processing methods are used for recycling.The difficulty of introducing recycling into LCA is to set the right boundaries for the different flows ending in different product systems. It is a question of which observed material flow belongs to the first product system and which one to the second or subsequent systems. Recycling can be part of any product LCA. However, it is often a complex issue which requires specific considerations. As pointed out by Yellishetty et al. and Birat et al. [l, 2], LCA practitioners are left with much freedom in allocation of environmental burdens to account for recycling, thus making subjective judgments on recycling and allocation of credits to recycling. This often makes it difficult to compare the results of LCA studies conducted by two different practitioners even on the same processes. As LCA is often used to define policy in government, business and society circles, it should be based on a sound, objective and unbiased description of recycling."

Jan 1, 2014

By Hong Yong Sohn

A novel flash ironmaking technology is under development at the University of Utah under the support of U.S. Department of Energy (DOE) and American Iron and Steel Institute (AISI). The history of the development from the conception of the idea to the current status will be discussed. The flash ironmaking process produces iron directly from fine iron ore concentrates without requiring cokemaking and pelletization/sintering, which will enable the technology to significantly reduce energy consumption and carbon dioxide emissions compared with blast furnace ironmaking. Unlike other gas-based ironmaking processes, this technology will not suffer from the problems of solid sticking and fusion. Current work is focused on the method of supplying the energy required to maintain the necessary temperature, as an intermediate step to determine the scalability for larger, industrial-scale pilot trials.

Jan 1, 2014