Search Documents

By N. A. Vatolin, L. I. Leontjev, S. V. Shavrin

The ever growing interest to the complex iron ores may be attributed to possible production of the naturally alloyed metals and the efficient recovery of the associated elements. However, the conventional technique for complex ore processing is complicated and in some cases even impossible. A pyrometallurgical benefiation of such ores without melted slag formation has been advanced. A version of the technique assumes pellet production with metal coagulated within a slag shell on grinding the pellets, the metal phase is mechanically separated from the slag shell. The technique has been run up with ferro chromo nickel, high-titanium, high-magnesia, alumina phosphorus ores and concentrates. Another version of the pyrometallurgical benefication without melted slag formation in a rotary kiln has been developed from the schemes for processing red mud of alumina manufacture and high-titanium concentrates. Means have been put up to improve schemes available for lex iron ore processing with primary emphasis on material pretreatment before blast furnace and steelmaking processes. Vanadium-bearing titanomagnetite conentrate oxidized pellets possess low strength at reduction. The technique suggested for pelletizing in the controlled atmosphere improves the afore said pellet metallurgical properties. Prodution of metallized pellets in a conveyor roasting machine holds considerable promise for blast furnace and steelmaking processes. In processing the high-sulphur iron ores still another technique is proposed to roast the fluxed pellets with 95% and more desulphuration.

Jan 1, 1988

By Jin-yan TIE, Ke-xin JIAO, Qian Li, Hai-bin ZUO, Jian-Liang Zhang, Meng SHEN

This paper designs three factors such as temperature, pH, conductivity and three levels of orthogonal test. Temperature is a significant factor. However PH and conductivity are not significant through poor analysis. Further research is conducted on the temperature. Temperature stability is 50 . Suitable water velocity is 2.3m/s, which is calculated based on the largest part of the heat flux intensity and the corresponding water temperature should be controlled with 1.5. Meanwhile, water velocity increased has little effect on the heat transfer capabilities.

Jan 1, 2015

By Alim Ullah

Process, quality and management control are necessary in order to produce DRI of required quality and at minimum cost. Although the characteristics of the two (2) principal inputs, that is, iron oxide feed and natural gas (for gas-based DRI plants) can affect the operation of a DRI plant significantly, they are outside the control of plant operators, at least in the short run. The quantity of reduction gas, its composition and reduction gas temperature are some of the key process variables. Statistical Process Control (SPC) can be used in a DRI plant to minimize the production of off-grade material and costs, as well as to improve the overall operation of the plant. One of the key quality variables to be measured and controlled is percent metallization, defined as FeM/FeT*100 where, FeM and FeT respectively are metallic iron and total iron in DRI. Control charts are used to monitor the quality of DRI produced and, when necessary, corrective actions are taken to bring the product back within the control limits. Management control can consist of essentially following how well the plant performs against some pre-established standards of parameters like daily production, downtime, consumption of material and energy, etc. In this respect, it is suggested that yield, defined as theoretical consumption/actual consumption of iron oxide feed, be used to monitor the consumption of feed material. Similarly, instead of using natural gas per ton of DRI produced, a better criterion would be efficiency, defined as theoretical natural gas consumption/actual natural gas consumption.

Jan 1, 2006

By J. H. Lee

LG Metals Corporation started its second smelter operation at Onsan along with the existing flash smelter on January 31, 1998. Onsan smelter has been producing about 140,000 tons of copper annually from concentrates with the flash smelting line since 1979. In accordance with an increase in domestic copper demand, LG Metals Corporation decided to expand smelting and refining capacity by introducing a second smelter line using the Mitsubishi continuous process and a new tankhouse in 1995. After two years' expansion works consisting of engineering, procurement, construction and a successful commissioning test, the total smelting capacity of Onsan smelter increased to 340,000 ton of copper annually from concentrates. This paper describes the smelting facilities, operation result, problems encountered and improvements during the start-up and early operation of Onsan's new smelter

Jan 1, 1999

By Shaohua Ju, Huang Chang-yuan, Lu Shuaidan, Peng Jin-hui, Wu Guoqin, Yaqian Wei, Zhang Li-bo

"The contrastive studies of microwave and conventional roasting copper residue from zinc hydrometallurgical was carried. The experimental results showed that the microwave roasting has the higher dechlorination rate in the same condition such as temperature, heat preservation time and atmosphere. When the samples with 100 mesh grain size, the Cl content turned from 14.27% to 1.33% and the dechlorination rate achieved over 90% at 400°C with 2h microwave roasting. And in the same conditions, the materials' dechlorination rate after conventional roasting just reached around 78%. The phase changes of the roasting process was investigated with X-ray diffraction analysis.IntroductionCl element can be accumulated gradually in the solution of Zinc hydrometallurgical system. When Cl content in electrolysis solution comes up to 100 mg/L, the stability of electrodeposits process would be severely affected [ 1]. It would not only accelerate the consumption of cathode and anode plate, elevate the power consumption, but also cause serious corrosion of device, increase production costs and lower the quality of electrolytic zinc [2]. Thus, C1- contained in the solution should be removed before electrodeposits."

Jan 1, 2013

By P. E. Donaldson

Since 1992, Falconbridge has made available to the international copper industry, Kidd Creek's licensed refinery process technology under the name of the Kidd Process. This has resulted in the supply and installation of permanent cathodes and associated product handling equipment to refineries in Canada, the United States, South Korea, Chile and Mexico. These installations accommodate both electrorefining and electrowinning processes. The growth and industrial acceptance of the Kidd Process has generated technical advancements in the areas of product random sampling, corrugation, marking, labeling, product tracking and data acquisition. In a different area, the expanded development of custom materials processing at Kidd created a need to advance technologically. The process-related problem of high nickel concentrations in refinery electrolyte compromised an increase in current density to >300 A/m2. The need for nickel removal resulted in Kidd Creek's newly developed Nickel Recovery System. The effective and economical extraction of nickel, along with reduced antimony and bismuth levels, reduces bleed stream volumes and/or neutralization costs and simultaneously produces a marketable nickel carbonate product.

Jan 1, 1999

By Jiann-Yang Hwang

Hydrogen storage is a critical issue for the hydrogen economy. Current storage technologies are not able to meet the combined gravimetric, volumetric, and system cost targets set by the Department of Energy. To solve the problem, the development of a new material - perhydride ? is proposed. Perhydrides are defined as materials that contain more hydrogen atoms in their molecules than conventional hydrides do based on the valence. This concept is supported by the versatile bonding capability of hydrogen and the recent discoveries in the chemistry of hydrogen clusters.

Jan 1, 2006

By Agnes Y. Lee

he U.S. Bureau of Mines developed a method to treat lead-contaminated soil and ebonite battery casing wastes to produce a nonhazardous material. The cleanup procedure involves wet screening to separate a minus 18-mesh soil fraction; removal of metal1ic lead, rocks, wood, etc. ; carbonation to change lead sulfate to acid-soluble lead carbonate; size reduction; acid leaching; and rinsing. The casing wastes undergo size reduction and washing to remove the lead sulfate sludge before carbonation. Similarly, the minus 18-mesh soil is carbonated, then acid leached and rinsed. In leaching, fluosilicic acid (H SiF,) and hydrogen peroxide (H20,) are used to dissolve lead compounds. An electrowinning method is employed to strip lead from the lead-rich leachate. The acid content in the leachate is replenished with fresh H,SiF, acid prior to recycling. Treated casing wastes and soils pass the Toxicity Characteristic Leaching Procedure (TCLP) test and can be reclassified as nonhazardous materia1s. Based on this process, a conceptual pilot plant has been designed which will be demonstrated on wastes from two Superfund sites.

Jan 1, 1993

By Pekka Taskinen

The converter-less nickel matte smelting technology (DON) adopted more than 20 years ago in Boliden Harjavalta smelter has been since that applied successfully to the processing of large number of nickel sulphide concentrates of various Ni-to-Cu ratios and MgO contents. The operational point of the technology is far from the conventional primary nickel smelting in the smelting-converting route. Therefore, a careful scouting of distribution equilibria of the base and trace elements in the smelting conditions of DON process has been conducted, in order to obtain quantitative information about the equilibria and thermodynamic properties of the nickel mattes at low iron concentrations, less than 10 wt% [Fe] in matte. The series of investigations has included novel experimental and analytical techniques for increasing the reliability and sensitivity of the phase equilibria as well as the element distribution observations carried out in typical high-grade nickel matte smelting conditions.

By Ruhi Bux, Akshay Verma, Mohini Saxena, P. Asokan

"Due to the colossal increment in the industrialization, the generation of wastes gathered as a result of different extraction, benefaction and generation processes is having an alarming problem for waste disposal. The best and most acceptable way is to use the waste in accordance to its potential for the generation of high value lucrative composite goods. The study in this paper elucidates the potential of several industrial wastes like fly ash, red mud and marble slurry dust for the production of different wood substitute products like doors, windows, roofing sheets and instant houses for the rehabilitation on the sites of catastrophes. Wastes were initially characterized for the physical, chemical and mineralogical properties and then used in different formulations with binder like Polymer along with natural fiber like Jute to intensify the physical as well as mechanical properties of the resultant composite. The study also reveals that these composites have better mechanical properties than the available ones like teak, medium density board, Rice husk board etc. Also, the fly ash and red mud composites have better mechanical properties than marble slurry based composites. The results fosters the implementation of natural fiber with the industrial waste in the generation of eco-friendly and non-hazardous composites.IntroductionOver the last few decades, there has been a tremendous increase in the generation of industrial wastes gathered as a result of various extractions, benefaction and generation processes. The condition worsens even, when it comes to high quantum generated wastes like Fly ash, Red mud and Marble slurry dust. The primordial motif behind the incorporation of industrial wastes as filler in the development of composites is primarily composed of two main objectives; Firstly waste management, the colossal waste dissemination in the environment has disturbed the ecological balance by polluting land, surface water, ground water, air, natural resources and even disturbing the public health [1]. Secondly, to act as a perfect substitute for the conventionally existing building materials, this will aid in dwelling places to many with the least incorporation of exhaustive natural resources as woods quid pro quo."

Jan 1, 2008

By M. Kobashi, T. Choh, N. Kanetake

"A new processing route, which enables the cost-effective and energy- saving fabrication of metal matrix composites, have been proposed. The pressureless infiltration of the reactive powder blend with molten aluminum was investigated in this work. The molten aluminum infiltrated into the [Ti + C] powder blend spontaneously, whereas the spontaneous infiltration into the TIC powder phase did not occur under the same experimental condition. The processing time was shortened and· the processing temperature was .lowered by adding the aluminum powder in the [Ti + C] powder. The differential thermal analysis revealed that the aluminum powder in the powder blend melted at 933K and then ignited the reaction between titanium and ·carbon. However there was an .optimum additional amount of aluminum in the powder blend. The TiC formed in situ had three-dimensionally continuous morphologyIntroductionThe squeeze casting process has been used as one of the processing routes for aluminum matrix composites. [1, 2]. Non-reactive metal-ceramic systems have been, generally, used in this technique in order to prevent the degradation of the ceramic phase. Materials obtained by this process basically consist of a continuous metal matrix and discontinuously dispersed ceramic particles. Reactive systems have begun to be introduced into the infiltration process· recently [3A]. Since the ceramics are synthesized in-situ, this process can provide a continuous ceramic matrix [5]. This is one of the outstanding features of this technique in that a bulk ceramic-can be synthesized at relatively lower temperatures in a short time. Another advantage is that the highly reactive combination of a ceramic with a molten metal is in many cases wettable [6], which enables a spontaneous infiltration."

Jan 1, 2000

By Beatryz C. Mendes, Igor K. R. Andrade, Roseli O. G. Martins, Gustavo H. Nalon, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Carol F. R. Santos, Marcelo A. Alves

This work presents an experimental investigation of the influence of concrete blocks and mortar’s compressive strength on the flexural bond strength, normal to the bed joints, of concrete structural masonry. Third-point beam tests were performed on concrete prisms, considering two different kinds of concrete blocks (compressive strength of 5.9 and 8.2 MPa) and six different cement-lime mortar compositions (compressive strength around 30, 70, and 120% of the blocks’ net area compressive strength). Units’ absorption and mortar’s initial flow and water retentivity were not varied, but remained within the suitable range for use in structural masonry. For both types of concrete blocks, it was observed an increase on the prism’s flexural bond strength with the increase of the mortars’ compressive strength. A lower mortar’s water-cement ratio led to higher bond strength. When fixing the ratio between mortar’s and concrete block’s compressive strength, it was noticed that the increase on the blocks’ strength contributed to a slight increase on the masonry’s flexural bond strength, except when using high strength mortar, in which the increase was significantly greater.

Mar 1, 2018

By Vadim J. Jabotinski

This paper describes several areas of application for electron beam processing of materials. The technology and use of electron beam systems in gas phase synthesis reactions are described. Gas phase reactions may be used to generate ultra- fine metal or ceramic powder that are very pure and crystalline. Among the examples presented are: the generation of nanometer sized metal powders and the gas phase synthesis of silicon carbide for silica and methane. The experimental system is described and future theoretical and experimental objectives are identified.

Jan 1, 1998

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By Bruno Lebon, Koulis Pericleous, Georgi Djambazov, Mayur Patel

"High speed compressible jets are used in a number of steel-making applications. In the case of the BOF, a compressible oxygen jet reacts with a carbon-rich iron bath to reduce carbon levels and produce steel. The intensity of the process is governed by the speed of the jet and by the size and shape of the depression created in the metal and slag by the force of the jet, i.e. by the corresponding free surface. This is a difficult CFD problem, since there are compressible and incompressible regions in the flow domain, which need to be handled differently in a finite-volume (FV) pressure-correction scheme. Also, standard turbulence models do not account for compressibility, or the large difference in density between the cold oxygen jet and the hot reacting surroundings. Corrections are introduced to the k-E model to remedy this deficiency and the results are validated against experimental data. The compressible/incompressible boundary is handled through a transition region, based on Mach number.IntroductionThe deformation of a free surface by a compressible high speed jet is of paramount engineering interest, particularly for understanding the physical processes within a Basic Oxygen Furnace (BOF). In a BOF, a supersonic oxygen jet impinges on a molten iron surface, thereby creating a cavity. Oxygen penetrates the bath and removes carbon, resulting in low carbon steel [1].The challenges in modelling such a process lie in coupling a solution domain with distinct compressible and incompressible regions and in dealing with large density differences between the modelled gas and liquid. The modelling of compressibility within the jet is crucial, since the correct velocity profile in the jet is required to determine the cavity depth with accuracy."

Jan 1, 2012

By Jian Li, Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"A study of the coal-based direct reduction behaviors of composite binder magnetite pellets was carried out in a simulating coal-based grate-rotary kiln process. It is shown that preheated pellets possess much better reducibility than fired oxide pellets: 40 min are required for preheated pellets to reach over 90% metallization degree compared to 100 min for fired oxide pellets. The compressive strength of preheated pellets decreases dramatically at the earlier stage of reduction, climbs quickly after reducing for 30min and achieves a high value at the end of reduction. However, the compressive strength of metallized pellets from reducing of fired pellets is much lower, more cracks and fractures being formed. In the preheated pellets, crystallite of metal iron is coarse. In the oxide pellet, a large number of interconnected crystals of metal iron are formed inside pellets, and pellet structure is very compact.IntroductionDirectly reduced iron is an excellent feed in electric arc furnace (EAF) steelmaking, and possesses low tramp element content and steady component. It is generally preferred in the production of high quality steel [1-3]. Nearly 64.44 million tons of DRI were produced in 2009 over the world, over 80% of which were produced by gas-based processes, the left by coal-based processes. However, the DRI capacity was only 600 thousand tons in China in 2009. The EAF steel production has exceeded 40 million tons annually, and most of EAF operate on hot metal as feed [4]."

Jan 1, 2011

At the present time, cyanide is the most widely used reagent to extract gold from its ores and concentrates. However, its use in mining has become the focus of intense attack by various groups throughout the world; as a consequence, a renewed effort has been launched to find suitable alternative lixiviants to recover gold. Chlorination was the most popular process to extract gold, before it was rendered obsolete with the advent of the cyanidation process at the turn of the last century, not least because it required the use of potentially hazardous and costly chlorine to oxidize/complex the gold. The PLASTOL® process, originally designed to recover the platinum group metals (PGM?s) from their ores and concentrates, provides an alternative to cyanide for gold ores. The process generates oxidizing conditions in the autoclave capable of forming the AuIII ion, and gold chloro-complexes result from the addition of small quantities (~5-10 g/L) of sodium chloride to the autoclave. The principles of the PLASTOL® process are briefly described, and several applications of the process to gold concentrates are presented. Various options available to recover gold from PLASTOL® leach solutions are also discussed.

Jan 1, 2003

By Ryokichi Shimpo, Akio Fuwa

"In order to elucidate the present status of process-control technology, survey study has been made on the present process control schemes of representative copper smelting and converting processes in Japan. Conceptual control flow diagrams have been deduced and shown on respective functional reactors, i.e. drying, smelting, converting and fire-refining units, where the objective OUTPUT items are correlated to the INPUT variables through respective CAUSE-AND-EFFECT RELATIONSHIPSFuture view has been also discussed on several feasible and desirable improvement and refinement ~n measurements and control system for better copper smelting and converting operations.INTRODUCTIONIn other to seek for the better and efficient operation in copper smelting and converting process, survey study has been first conducted on the present process-control schemes of respective functional unit processes, i.e. drying, smelting, converting and refining unit processes, of representative copper production processes in Japan. Conceptual process flow chart of control scheme has been then deduced where output items are correlated to input items through the respective cause-and-effect relationships.After this survey study, future view has been discussed on the feasible and desirable improvement and refinement in the measurement and control system in these processes. Emphasis has been placed on the better and precise measurements of temperature, oxygen partial pressures in respective furnaces and end-point in converting and refining unit operations."

Jan 1, 1989

By Shun Fujieda, Shigeru Suzuki, Kozo Shinoda, Tetsuo Fujita

"Dowa Metals & Mining Co. Ltd. has developed and plant-practiced a unique scorodite synthesis technology (DMSP®) for arsenic immobilization by oxidizing Fe(ll) ions in the presence of As(V) ions. Dowa has improved the DMSP® technology and has developed the process extensively for other applications. This paper focuses on the applicability of the DMSP® for various cases of copper smelting, and introduces other technologies for fixing arsenic and recycling gallium from GaAs, simultaneously processing (fixing) arsenic and thallium, and fixing and recovering arsenic from dilute arsenic solutions. The DMSP® was found to be applicable not only for various processes in nonferrous smelting, but also for other applications with a high potential for reducing environmental problems.IntroductionDowa Metals & Mining Co. Ltd. developed a method for synthesizing scorodite at ambient pressure [1], The scorodite is precipitated by oxidizing Fe(II) ion in a high-concentration As(V) solution. The scorodite produced in this way does not readily release arsenic because of its high crystallinity. Dowa built a demonstration plant for this technology at the Kosaka Smelter and established the production of scorodite at 30 t As/month by treating intermediate products from copper smelting as the starting material. The DMSP® was demonstrated to be favorably applicable to copper smelting [2]. We are engaged in further increasing the amount of arsenic fixation by the use of this process. Further improvements in productivity, cost reduction and applicability in various processes have been devised. Dowa has been endeavoring to resolve other problems as well as to improve productivity. We have gained extensive knowledge on arsenic treatment in our endeavors, enabling us to solve problems and improve productivity. This paper introduces the investigations and developments related to DMSP®."

Jan 1, 2012

By Ioannis Paspaliaris, Dimitrios I. Gerogiorgis, Dimitrios Panias

"Red mud fiberization is a process with remarkable potential, alleviating environmental pressure by transforming an aluminum by-product into mineral wool, thus to various marketable products. A promising mineral wool process is molten slag fiberization via an impinging air jet, which avoids mechanical wear and rotating parts. The molten slag which remains after pig iron casting flows out of a heated ladle orifice at a high temperature (1600 °C) and adjustable flowrate, and forms a free-falling vertical jet which visibly radiates its excessive heat: at a given distance, a high-velocity impinging air jet meets the vertical melt jet perpendicularly (or at an angle), inducing intensive droplet generation, subsequent fiber elongation, collection and processing.This paper focuses on high-fidelity CFD modeling of the molten jet flow under external cooling: the model encompasses all physicochemical phenomena (melt laminar flow, radiative cooling) and considers several temperature-dependent slag transport properties in order to understand which operational degrees of freedom (manipulated variables) are useful to process optimization."

Jan 1, 2012