Search Documents

By Susumu Imashuku

A pseudoternary phase diagram of the BaO?ZrO2?ScO1.5 system is established and the conductivities of the scandium-doped barium zirconate are measured in wet conditions. According to the phase diagram, the molar fraction of scandia in the barium zirconate phase that equilibrates with the cubic zirconia (ZrO2) and scandia (Sc2O3) phase is 0.03. On the composition line, where the molar fraction of barium oxide (BaO) is 0.50, the solubility of scandia into barium zirconate is 0.27 as a molar fraction of scandia. At around 500 °C, the conductivities of scandium-doped barium zirconate are estimated to be almost same as that of yttrium-doped barium zirconateThe activation energies for bulk proton conduction in scandium-doped barium zirconate (0.57 eV for BaZr0.90Sc0.10O3-d) are higher than that of yttrium-doped barium zirconate (0.44 eV for BaZr0.90Y0.10O3-d). In addition, the bulk conductivity of scandium-doped barium zirconate in this study is 10 times higher than the reported conductivities in the temperature range of 75 °C to 300 °C.

Jan 1, 2006

By June-Yong Eom, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

The nitrogen solubility in liquid Mn-Si, Mn-Si-Fe, Mn-Si-C and Mn-Si-Fe-C alloys has been measured by the gas-liquid metal equilibration technique in the temperature range of 1673-1773 K. The additions of silicon, iron and carbon significantly decreased the nitrogen solubility in liquid manganese alloys. The experimental results were thermodynamically analyzed by the Wagner’s formalism to determine the first- and second-order interaction parameters of silicon, iron and carbon on nitrogen in liquid manganese. The thermodynamic parameters can be used to predict the nitrogen solubility in ferromanganese and silicomanganese alloy melts as functions of the melt composition and temperature at given nitrogen partial pressures.

Jan 1, 2014

By M. Rosales

By a physical and mathematical modeling, the behavior of the tri-dimensional waving, and the movement of the gases at the Teniente Converter was studied. The mathematical model considers the condensed phases of white metal and slag, along the gas phase, and includes the k-e model for the turbulence description. Both the physical model and the mathematical model allow to conclude that from a fluidynamic stand point the Teniente Converter clearly can melt 3000 tpd of concentrates. Also, both models are suitable to predict the slag fluidynamics and its spacial distribution inside the Teniente Converter, and the splashing in the tuyere zone as well.

Jan 1, 2006

By John M. Gaines

Lead concentrates from the Viburnum Trend in the Southeast Missouri Lead district are sintered prior to smelting to bind the particles together homogenize the feed, and reduce the sulfur content. Good sinter forms competent masses about 4 to 6 inches across, that hal!e about 15% porosity and good mechanical strength to withstand transport and the weight of the overlying load in the smelter. Bad sinter has poor mechanical strength and forms fine fragments that retard the circulation of reducing gases in the furnace and lengthen the time required for reduction. The productivity of the lead smelter depends on good sinter feed. Because some lead sinter plants produce bad sinter about 20% of the time, this applied mineralogy study has been undertaken to determine the mineralogical and microtextural differences between good and bad sinter. A reflected light microscopic study of 130 polished sections has shown that good and bad sinters differ distinctly in their mineralogy, tex1ure. and character of, porosity. Good sinter consists of hardystonite, franklinite. lead-zinc-bearing magnesium-calcium silicate, lead silicate matrix, and large crystals of calcium-magnesium-iron silicate, together with minor amounts of lead oxides, lead-zinc silicate, metallic lead, specular hematite, magnetite, lead-iron-bearing zincite and zinc-Iead-magnesium-bearing wustite in a tightly intergrown mesh of crystals and with an evenly distributed porosity of 15% to 20%. Electron microprobe analyses show that the principal phases contain lead (or zinc): hardystonite (4-20% Pb) franklinite (2-14% Pb) and lead silicate matrix (65-74% Pb). Bad sinter differs from good sinter in the greater abundance of lead silicate matrix, galena metallic lead, and lead oxides and the lesser abundance of hardystonite, franklinite and calcium-magnesium-iron silicate. Bad Sinter is characterized by a lack of an intimate intergrowth of the constituent phases. Its porosity is much lower commonly 0 to 5% and those pores are concentrated in local areas rather than distributed evenly throughout the sinter.

Jan 1, 1991

By J. T. I. Poijärvi

Outokumpu Harjavalta Metals Oy operates copper and nickel smelters, three sulphuric acid plants and nickel refinery at Harjavalta and copper refinery and precious metal plant at Pori. The by-products of these plants are presented in this paper. The by-products of the smelters include products from slag cleaning of flash smelting furnaces and converters, flue dusts and smelter off-gases. Weak acid and sludges from cleaning of smelter off-gases and acids are the by-products of the acid plants. The by-products out of the copper refinery are crystallized metal sulphates and sludges from electrolyte purification, on which a co-production process of the copper tankhouse is based. The main by-products of the precious metals plant are products from anode slime treatment and platinum metal group concentrates in the recovery of precious metals. Sludges from nickel matte leaching and precipitates from solution purification are the by-products of the nickel refinery. The formation, treatment and processing as well as the research work done for the utilization instead of dumping of the by-products in the production of copper and nickel will also be discussed in this paper.

Jan 1, 1995

By Dan Wang, Qian Li, Yong-bin Yang, Tao Jiang

"Thiosulfate is one of the most promising non-cyanide lixiviants for gold leaching. However, the undesirable reaction between thiosulfate and copper (II) gives rise to increased reagent consumption, which results in high cost and huge limit to its development. This paper presents study on the effect of ammonia, copper (II) and Cu(NH3)l+ ions on the oxidative decomposition of thioulfate. It shows that the presence of copper (II) and Cu(NH3)l+ can significantly increase the thiosulfate oxidation, while ammonia is relatively unaffected. The oxidation of thiosulfate by copper(II) in the absence of ammonia is fast at first and then decreases as time increased within a certain time, which can postulate that an intermediate product is responsible for the decreased consumption. The effect of ammonia is depended on the interaction with copper (II), which was found to significantly affect the consumption of thiosulfate.IntroductionFor over one century cyanidation is widely used in industrial production of gold, due to its simplity of process and low cost of production. However, cyanide is a highly toxic chemical reagent used dangerously and brings serious environmental pollution. What's more, cyanidation has slow speed of leaching gold and poorly leaching effective for refractory ores. With the exhausting of free-milling gold ores and promoted environmental protection requests, the disadvantage of cyanidation becomes a growing problem. In recent years, more and more research activities have been focused on alternative processes using non-cyanide lixiviants. Among the non-cyanide lixiviants, thiosulfate is considered as the most promising one[l-5].Compared to cyanide, thiosulfate is an inexpensive, nontoxic and less-pollution reagent, which can form complexes with many metal ions. Thiosulfate leaching of gold has an acceptable leaching rate and is insensitivity to impurities. Moreover it presents advantage on the treatment of refractory gold ores such as carbonaceous gold ores, copper gold ores, complex arsenic and sulfur gold ores, and so on[6]."

Jan 1, 2013

By Malti Goel

"Ferrous and Non-ferrous industry in India is undergoing a transition to meet the growing demand and a new thrust to Research & Development (R&D) is mounting. On one hand, to meet the target laid by the policy in the Iron and Steel sector of 110 million tones production by 2020; on the other, innovations taking place in light metal production technology; both have necessitated greater attention to development of industrial ecological framework. Industrial ecology provides a number of new challenges as well as opportunities for the industry. The development and growth in a particular industry should have a trend towards reduced energy consumption, reduced resource consumption, thereby reducing the cost of production. Technology management strategies will have a key role in achievement of these targets. The paper describes recent developments in technology management, importance of R&D and case studies on adoption of energy efficient & CO2 reduction technologies in metal industry in India. In the end suggestions for future are made.IntroductionInternational Energy Agency [1] has assessed that nearly one third of the World’s energy consumption and 36% of CO2 emissions are attributed to manufacturing industries. In case of ferrous and non-ferrous metals, the resource equality and product quality finally determine the energy share across the countries. In the overall, Iron & Steel industry accounts for about 19% of total industrial energy used. The saving potential for non-ferrous metals is estimated to be anywhere between 13 to 25 % of the energy consumed depending on the level of resource quality. The projections are that energy consumption worldwide in Industry sector would increase 1.8% per annum up to 2030 on average, and up to 2.5% in developing countries."

Jan 1, 2008

By Sang-Joon Kim, Hae-Geon Lee, Hyun-Jin Cho

"Decarburization phenomena on the surface of liquid iron have been simulated by numerical method and the results were compared to the experimental data. During the DeC process in a converter, a large amount of splashed droplets are generated from the top surface of the bath and consequently the reaction surface area is increasing tremendously. Since the decarburization mainly occurs at the interface, it is important to understand the reactions on the liquid iron droplets. The flow and species concentration fields around liquid droplets taking into account the reaction of carbon with oxygen at the interface were calculated by a commercial CFD code FLUENT which solving multiphase Navier-Stokes equation with Volume Of Fluid method, species transport equations and energy transport equation. The initial carbon concentration was fixed to 4 wt% and the concentrations of oxygen in the atmosphere were varied from 5 to 50 wt%. As comparing the numerical calculation with experimental data written in the reference, the results have a good agreement for decarburization rate.IntroductionIn a primary steelmaking process, one of the main functions is to decarburize from hot metal and the 4% of carbon is decreased to about 0.5% of carbon. Even though there are some possible reactions leading to the removal of carbon from hot metal, the main reaction occurs on the free surface by direct oxidation of carbon at the gas-liquid interface with producing the carbon monoxide gas. In many metallurgical processes involving a jet impinging onto a steel bath surface, especially in a Basic Oxygen Furnace (BOF) converter, it is important to understand the behavior of molten iron droplets splashing out of the steel. The iron droplets are generated by an oxygen or air jet blowing and it increases the total surface area of liquid iron tremendously. Since the decarburization reaction is mainly affected by the surface area, it is necessary to verify the decarburization phenomena around the splashed droplets from liquid iron in order to allow an analysis ofBOF process possible."

Jan 1, 2011

By Reza Rahimi, M. Nili Ahmadabadi

"Because of high cost and shortage of primary resources of Ni-base superalloys, revert alloys can be used as a part of charging materials for production of superalloys ingots. The current study is based on recycling of IN738LC, a Ni-base superalloy, using 30% and 50% reverted alloy and balanced amount of virgin raw materials. Therefore, it has been attempted to cast an alloy with references to standard chemical composition and mechanical properties. After charging and casting in vacuum melting furnaces, chemical composition verification and non-destructive tests (i.e. Penetration and Radiography Tests), quality of samples were evaluated at elevated temperature by stress-rupture test. Results acquired from chemical composition and mechanical test indicate that cast ingots using 30% and 50% reverted alloy is reliable and consistent with the quality control requirements.IntroductionIn recent years, there have been many fluctuations in cost and availability of raw materials which are extremely determining in Ni-base superalloys production. Accessibility to the high purity metals such as Cobalt, Molybdenum, Tantalum, Niobium and etc. have been problematical during the past decades. Therefore, shortages of critical raw materials beside the economical considerations motivated the alloy suppliers and investigators to study and find alternate sources such as reclamation and recycling of scraps [1].There are a lot of reasons for the necessity of recycling; perhaps the most justifiable one is that consumers themselves produce scraps. For example, the weight of a finished superalloy product could be less than one-third of the cast alloy weight and in the case of complicated machined parts; this portion may reach to one-tenth [2]. High values of constituents, reduction of energy consumption and environmental concerns have all strengthened the obligation of recycling in Ni-base superalloys.Because of the high degree of risk in usage of improper materials for production of turbine blades, a delicately controlled program for recycling is needed. Depending on the type of scraps, this program can define the recycling procedure, required instruments, allowable percentage of scrap for usage and finally confidence level of the process."

Jan 1, 2012

By Hoda Emami

In this study, a combined pyrometallurgical and hydrometallurgical technique has been designed and used to recover rare earth mixture elements (REE) and cobalt from a NdFeB magnetic waste. while addressing the cost of reagent and process facility. This process can be adjusted to different magnetic wastes regardless of their compositions. Prior to the leaching, the magnet scrap was pretreated by two rounds of roasting (750°C in air) and a mechanical grinding in between, to convert iron metal to ferric oxide. Subsequent leaching was performed using optimized conditions (pH, temperature and retention time) where the extraction ratio of REE to Fe III is the highest. After removing iron content from the leachate (pH ≈ 3), REE was precipitated selectively and purified further. The produced REE concentrate reaches 99% purity with 85% recovery in a single run. The cobalt oxide was isolated from the PLS as a by-product with 99.8% purity.

By Atinuke Oladoye, David Esezobor

"Particulate Copper Silicon carbide (Cu-SiCp) composites find application as wear and heat resistant materials in electrical sliding contacts such as in homopolar machines, railway overhead current collector systems where high electrical/thermal conductivity combined with good wear properties is required. However, challenges occur during machining due to the presence of hard reinforcement in the matrix. This may lead to high turnover of tool wear and poor surface finish. The adoption of near-net shape technology to produce such hard-to-machine metal matrix composites and subsequent finish machining with its attendant cost has reported limited success. This paper critically appraises the challenges and opportunities in the improvement of tribological characteristics of particulate Cu-SiC composites and identifies low cost reinforcement material that could be used to improve its tribological characteristics.IntroductionTribology consideration is increasingly becoming a decisive factor in the design and selection of materials for applications involving interacting surfaces in relative motion. The consideration is mainly on the combined effects of friction and lubrication on material's wear integrity and performance amongst other. Annual losses due to tribology in the US industries are estimated at between 1-2% of the Gross National Income [1], in Russia it is about 1-4% of the GDP [2]. Thus, the attributes of tribology has become imperative in modem machinery especially those applications involving sliding and rolling surfaces, and electrical contacts [3- 8].These are readily found in homopolar machines, internal combustion engines, aircraft engines, gears, cams, seals and railway overhead current collector systems [9-12]. In these systems, the dissipation of frictional heat arising from the interacting surfaces as quickly as possible imposes constraints on the choice of materials for such application to prevent softening, plastic and shear flow and the transfer of metal as wear debris onto the interacting surfaces. If these possibilities occur, system performance is compromised and premature failure may result. Materials for these systems are expected to possess high electrical and thermal conductivities, low coefficient of thermal expansion, good corrosion resistance and high melting point [3-8, 13]."

Jan 1, 2011

By N. Shi, T. C. Lowe, S. J. Zhou, M. L. Lovato, Y. T. Zhu, J. A. Valdez, W. R. Blumenthal, M. G. Stout

"A major problem of short-fiber composites is that the interfaces between the fiber and matrix become a limiting factor in improving mechanical properties such as strength. For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber, thus reducing the ineffective fiber length. However, a strong interface will make it difficult to relieve fiber stress concentration in front of an approaching crack. Stress concentrations result in fiber breakage. We report in this paper an innovative approach to overcome this problem: reinforcement morphology design. Short-fibers with enlarged ends are processed and used to reinforce a polyester matrix. The initial results show that the bone-shaped short-fibers produce a composite with significantly higher strength than can be attained with conventional short, straight fibers.IntroductionThese interfaces between the fiber and the matrix in short-fiber composites play a critical role and, in many cases, become a limiting factor in improving such mechanical properties as strength and toughness of the composites (1-4). For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber. A stronger interface can reduce the ineffective length at both ends of the fiber and, therefore, can increase the effective length that carries load (5-9). However, with a strong interface it is difficult to relieve fiber stress concentration -in front of an approaching crack; and such stress concentration can result in fiber breakage (10, 11). This effect is particularly severe for ceramic matrix composites, because of their low matrix toughness and lack of plasticity. Even for a composite with a highly ductile matrix, such as plastics, too strong an interface may still cause successive adjacent fiber breakage and subsequently reduce composite toughness (1, 11). On the other hand, a weak interface significantly decreases the fiber load-carrying length due to ineffective load transfer and complete fiber interfacial debonding and pullout during loading. A compromise in the interfacial bond strength will also compromise the load-carrying potential of short fibers."

Jan 1, 1998

By L. Salinas

Lance injection of gas and particles into a molten bath is currently practised in metallurgical processes (Mitsubishi lances for example). Several experimental and theorical studies have been conducted in the past on this topic. However, neither detailed calculations nor experimental studies of local flow patterns have been published. In the present work, a numerical simulation of the interaction of a gaseous vertical descending jet and a liquid surface was done, using the turbulence k-e model. There is a fair agreement between the calculated and the experimental values. The results of this study demonstrate that it is crucial that the gas jet velocity profile and turbulent characteristic are correctly formulated in order to correctly simulate the system.

Jan 1, 1999

By H. Hirayama, T. Okura, O. Kato

"Saganoseki Smelter & Refinery, one of the largest copper smelters in the world, has the annual capacity of 300,000 metric tons in copper content with two flash furnaces, six Pierce-Smith type converters, two anode furnaces, four acid plants, three tank houses and perfect pollution control system.Coping with the many severe conditions surrounding the copper industry in the last decade, Saganoseki Smelter has kept performing the stable operation, while enhancing the smelting capacity and developing new technologies such as the hydrometallurgical treating of converter dust recovered at electric precipitators. Especially in the operation of flash furnaces, which are of Nippon Mining's conversion type using hot air in a temperature of l,000ºC some technological improvements and complete operation control factors have approved the concentrate feed rate to reach to 2,200 tons a day for a flash furnace.Reported in this paper are the production control design for copper smelting process, and the operation control scheme of the flash furnace following the brief review of the characteristic of Saganoseki Smelter's process and some improvements. Copper Smelting ProcessDescriptions of major unit operations and general specifications of the copper smelting facilities are summarized in Table 1, and the present flowsheet of the copper smelting is described in Figure 1 (1,2).Outputs and raw materials treated in the last five years are shown in Table 2, in which concentrate includes powder copper scrap which amounts to 3 to 4% of concentrate.A full operation was performed for a period of one month, for both one flash furnace operation and for two flash furnace operation. With one furnace operation, 19,200 tons of copper were produced. With the two furnace operation, 84,000 tons of concentrates were charged and 33,500 tons of anode (net 28,600 tons of copper) were produced.The actual production level, however, has been kept at 80 to 90% of the full capacity because of low copper price, tight market of copper concentrate or fall of net demand in Japan."

Jan 1, 1989

By Honorio Oliveros Gómez, Oscar Jaime B. Restrepo

"Colombia produces nine tons of electronic waste per year and there are approximately 60 tons accumulation generated in the last nine years. This work aims to establish a general methodology in the laboratory to recover gold, silver and platinum group present in electronic waste, also explore other forms of recovery of metals contained in electronic waste. We selected seven types of electronic cards present in the computers, which have their parent desoldering electronic components. Initially, we characterized the components of the cards through X-ray diffraction and SEM, to identify the metal species and composition. Tests were conducted laboratory hydrometallurgical recovery of metals. This paper proposes a methodology for laboratory-scale work.INTRODUCTIONColombia produces nine tonnes of electronic waste per year and build there in about 60 tons generated in the last 9 years [1], Computers, TVs, audio equipment, monitors, cell phones, remote controls, printers and operated toys battery, among others are part of this inventory, which mostly comes to landfills, because the lack of legislation to control the final destination of waste electrical and electronic equipment, and lack of efficient technologies to recover materials [2]. Under these circumstances which have environmental implications, technological and economic recovery is essential metals present in the electronic cards of computers, by hydrometallurgical with subsequent base metal electrodeposition [3]. Pyrometallurgical route is discarded by major implications for economic and environmental [4]. Recovery From this perspective, the determination of the metal fraction and the relationship between the different metals, using the SEM characterization techniques - BSE and XRD is indispensable [5] It follows with electrolytic dissociation processes in the leaching and electrodeposition [6], and unit operations in the laboratory to carry out successfully these processes on a larger scale. Were randomly selected computer twenty-four postcards for nine types of cards have different functions in the computer, which, through the absorption desoldering technique, they broke the resistance (thermal, surface, photoresist, power), capacitors (ceramic, electrolytic), diodes (silicon, germanium, high frequency), transistor (NPN, PNP), processors, integrated (high, medium and low frequency), the RAM card and pin parallel port serial"

Jan 1, 2011

By Cheng Pan, Xuewei Lv, Guibao Qiu, Chenguang Bai, Meilong Hu

"Physic-chemical properties of slag at high temperature play an important role in the pyrometallurgical process of production of ferronickel alloy. It determines the operation efficiency, metal recovery ratio, energy consumption and the distribution of elements like S and P between the slag and metals. In the present work, the effect of MgO content in the slag on melting features and viscosity of the slag was investigated. The MgO content in the SiO2-CaO-MgO-Al2O3 -FeO in the quinary slag system varied from 14.5% to 22.5%. The results shown that all slag samples begin to softening at the same temperature, the softening temperature, melting temperature, flowing temperature decrease with the increase of MgO content when the MgO content is in range of 14.5 and 20.5 pct mass, and when MgO content up to 22.5 percent, the temperatures increase sharply. Besides the inflection point temperature of viscosity-temperature curve increase with the increase of MgO when the MgO content is in range 16 and 22.5 pct mass.IntroductionNickel is very important to modern society, without it, we would not be able to share many things in our daily life, such as airplanes, computers and many stainless steel appliances in our homes and workplaces1.. It is the essential element of the stainless steel making, and about 65% of the nickel consumed in the world is used to make stainless steel2., so with the increase of stainless steel, the nickel production and demand has continued to increase3.Nickel is produced from two distinct ore types: nickel sulfide deposits and oxide nickel laterite deposits. The great majority of world’s known nickel resources are contained in laterite deposits3.. The laterite ores are normal classified into two groups: the high-iron laterite ore and high-magnesia laterite ore1. Typical composition of high-magnesia laterite ore is in the range 1-3%, and these ores are suitable for pyrometallurgical process to produce ferronickel4."

Jan 1, 2012

By T. -M. Guo, M. J. Braun

"This paper presents an experimental and numerical study of melt flow near the solid-liquid interface and its effect on the interface curvature in a horizontal unidirectional solidification system with succinonitrile. Melt flow is introduced by increasing the ampoule channel thickness. Visualization techniques are employed to observe the flow field and the solid-liquid interface curvature. A numerical model is also developed to simulate the heat transfer, melt flow and phase change in the system. Quantitative information on the flow and temperature fields is generated. A good agreement is achieved between the experimental observations and model predictions. The results could be used for the study of the effect of the melt flow on interface morphology during solidification.IntroductionClassic unidirectional solidification experiments of transparent alloys are conducted with thin film samples sandwiched between two glass slides to investigate the development of interface morphology during solidification [1]. Samples with small channel thickness are usually used to suppress any melt flow due to natural convection and solidification in the channel would then be in the diffusive regime so that the solidification theory can be significantly simplified [2, 3]. Effects of melt flow, in particular due to natural convection, on solidification have also been studied extensively in those systems with large geometrical dimensions [4-6]. These studies indicate a strong effect of the melt flow on interface curvature during solidification [5, 6]. Only limited efforts were made to address the effect of the melt flow on interface morphology in horizontal unidirectional solidification, in particular for the cases when the channel thickness is not thin enough to suppress completely the natural convection [7]."

Jan 1, 2004

By J. D. Miller

Low-level radioactive contaminated soils (10-500 pci/gm) created by defense-related activities at certain superfund sites, such as Nevada Test Site (NTS), is a current environmental concern. Many of these contaminated sites may require appropriate cleanup and restoration, which could cost billions of dollars and put tremendous pressure on our limited financial resources. Therefore, the development of a selective flotation process to separate such radionuclides from contaminated soils should be considered. In this study, both a pure depleted UO2 sample and three synthetic UO2/soil mixtures were used to evaluate surface chemistry features and to examine the possibility for the flotation of fine UO2 particles from selected soils. It was intended that this model system would be a reasonable representation of contaminated soils such as those found at the Nevada Test Site which are reported to be contaminated by PuO2 fallout. The effect of reagent schedule, particle size distribution, and surface charge are discussed with respect to the flotation separation of the UO2/soil mixtures. It was found that both commercial fatty acids and reagent grade sodium oleate are effective collectors for UO2 flotation provided the pH is adjusted to the range of pH 8-9. The bench-scale flotation results successfully demonstrated that froth flotation technology can be used to remove UO2 from such model contaminated soils with appropriate flotation chemistry conditions which depend on the soil characteristics and other pretreatment procedures. In the best case, 90.2% of the UO2 was removed from a UO2/NTS soil mixture (119 ppm UO2) and the soil reduced in UO2 contamination from 119 ppm to 17 ppm in a single stage bench flotation. The impact of clay slimes present in the soil is revealed by the results which show that, for example, for a deslimed soil (28x400 mesh and 100 mg UO2/kg soil) 85¬90% UO2 recovery can be obtained with a reduction in contamination to 4.6 mg U02/kg soil.

Jan 1, 1995

By Eduardo Juncal, Jorge Alberto Soares Tenorio, Jose Roberto de Oliveira, Denise Crocce Romano Espinosal

"Steel industry has been expanding every year, consequently there has been an increase in waste generation in this area. Thus, companies in this sector are finding it difficult to give a correct destination of waste. For example, only in a basic oxygen furnace (BOF) converter are generated about l8kg of dust per ton of steel. The aim of this work was the characterization of dust generated in the BOF converter. The characterization was performed by chemical analysis (titration for iron and its oxides and Inductively Coupled Plasma Atomic Emission Spectroscopy for other elements), scanning electron microscopy, size analysis using Mastersizer 2000 equipment and X-ray diffraction. It was observed that dust is composed mainly iron in form of magnetite, metallic iron and wustite with approximately 99% of the particle size below 100 µm.IntroductionToday, steel is a important metal for the world. It can be produced for two routes, blast furnace/ basic oxygen furnace (BOF) converter and electric arc furnace (EAF) [1].First route, the iron is produced from the reduction of iron ore and coke for fuel injection and! or natural gas for a production of pig iron in blast furnace. The pig iron is sent until BOF converter to perform the blowing of oxygen to obtain the steel. In the second route, the steel is produced using scraps or direct reduced iron (DR!) using electric arc.During steel production are generated a lot of wastes like slag, sludges, scraps and dust [2]. Only in the first six months of201O, world steel production totaled 706 million tons [3]. According to Watson and Wang [4], some 10 to 20 kg of dust is generated per tonne of liquid steel produced. Thus, the reuse of these wastes can be a great to companies, because it reduces the amount of raw material to be extracted and reducing disposal costs [5,6]."

Jan 1, 2012

By María Cristina Ruiz

Hematite precipitation is a convenient alternative for the removal of iron from leaching circuits because of its chemical stability, high density and high iron content. The precipitation of hematite from ferrous sulfate solutions was studied in a batch reactor. The precipitation occurs by two sequential steps: oxidation of the ferrous to ferric ions followed by hydrolysis of the ferric to hematite. The main objective of this study was to determine the effect of the main operating variables on the rate of two steps of hematite precipitation. The variables studied included: stirring speed (100 to 600 rpm), temperature (160 to 200 ºC), concentration of sulfuric acid (1 to 10 g/L), initial iron concentration (1 to 15 g/L), and partial pressure of oxygen (1 to 6 atm). The sulfur content and the particle size of the solids that precipitated under various conditions were also determined. The results showed that at low temperature and high acid concentration the rate of Fe3+ hydrolysis is the step that controls the overall process. The variable that affects most the rate of Fe2+ to Fe3+ oxidation and the rate of hematite precipitation is the temperature.

Jan 1, 2008