Search Documents

By Shu Cheng

Abstract: Based on the consolidation theory of soil dewatering and land subsidence prediction methods in soil mechanics, preliminary analysis of surface subsidence and movement due to groundwater withdrawal was performed using the stochastic theory and the principles of effective stress and the method for subsidence prediction was derived, Surface subsidence due to coal mining was then superimposed to obtain the total subsidence. Keywords: land subsidence, rock and soil consolidation, stochastic theory, effective stress

Jan 1, 2002

By Graham Daws

The introduction of UK rock bolting technology has been applied in many large underground coal mines around the world. This paper explains the methods that have been applied for its successful introduction and discusses several case studies. It does not give fine detail but is intended to allow decision makers to gain a basic understanding of the method used to introduce rock bolting to a mine.

Jan 1, 2011

By Jinhua Wang

Based on engineering examples and theoretical analysis, the mechanism of chemical consolidation for fractured roadway surrounding rock was discussed. The chemical consolidating materials and three consolidating methods, that is, capsule, forced infusion and spraying, were introduced. Finally the application effects of the chemical consolidating technique to reinforce the fractured surrounding rock of roadways were analysed.

Jan 1, 1996

By Gennaro G. Marino

Site conditions at several shallow room and pillar mines in Illinois are described and compared with the charac¬teristics of the subsidence profiles at the ground surface. The shape and magnitude of the subsidence profiles were found to be closely related to the thickness of the soil and rock over-burden the percent extraction of the coal, and the shape of mine pillars. The room and pillar mines were located at a shallow depth (from 112 to 220 ft), beneath flat to gently rolling terrain. Thickness of the coal seams ranged from 5 to 9 ft and at all sites was underlain by underclays. This information has been developed in order to improve techniques for evaluating the subsidence potential at sites within the Illinois coal basin. he results presented form a small portion of the work carried out by the University of Illinois with Illinois Abandoned Mined Lands Councils and the U. S. Bureau of Mines at the Minneapolis Research Center in Minnesota (Marino and Mahar, 1985). Presented in the paper are the modes of mine failures observed for Illinois room and pillar mines, an overall summary of the site geologic and mining condi¬tions, case histories of each mode of failure, a comparison of sag profiles, and then an empirical relationship between the site conditions and the maximum sag subsidence. The most ideal case histories are presented to illustrate fundamental behavior. A brief of the Paper is given in a summary and conclusions section.

Jan 1, 1984

By Morgan Sears

The LaModel program (Heasley, 1998) is a displacement discontinuity, boundary element model (BEM) for analyzing stresses and displacements in single and multiple-seam coal mines. After the Crandall Canyon mine collapse, the need for better design guidelines for LaModel was observed and a new calibration method for deep cover pillar retreat was developed (Heasley et al., 2010). However, the scope of this initial calibration was limited to single-seam mines deeper than 750 ft. This limited application of the initial calibration method lead directly to the research presented in this paper, which attempts to define appropriate LaModel calibration guidelines for pillar design where shallow cover and/ or multiple-seam mining scenarios are encountered. As part of this research, a database of shallow cover case histories has been developed, and this database is used to help validate the shallow cover calibration method. By adding the shallow cover database to the previous deep cover database, the LaModel calibration method has now been extended to the complete range of mining depths, as well as to multiple-seam cases. With this shallow cover calibration, the utility of the LaModel program continues to increase.

Jan 1, 2013

By WenFeng Li

Comparing to the coal seams in Eastern China, the coal seams in Western China usually have better geological conditions. Therefore, changes in the conventional gateroads layout are required for the Western longwalls. A case study based on a Western coal mine (LiMin) was presented to discuss the feasibility of an innovative gateroads layout. Based on the geological conditions, a 5m wide pillar between the adjacent two longwall panels, 09112 and 09113, was proposed in order to increase the recovery rate. More importantly, the entry supporting strategy of panel 09113 headgate needed to be determined and verified carefully since only 5m wide pillar was left to separate the entry from the panel 09112 gob. Three strategies with different supporting intensities in the panel 09113 headgate were evaluated by numerical modeling. The model outputs indicated that roof and rib boltings plus single hydraulic props were essential to maintain the gateroads stable. Field observation showed that under the proposed entry supporting strategy, the total roof-tofloor and rib-to-rib convergences were only 360mm and 460mm, respectively, during the service life of the panel 09113 headgate, which indicated that the innovative gateroad layout proposed in this paper is suitable for longwalls with similar geological conditions in Western China.

Jan 1, 2013

By Wenbing Guo, Yi Tan, Erhu Bai

"It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.The surface movement and deformation caused by coal mining not only influence the ecology environment in the mining area, but damage the surface structures such as buildings, railroads, highways, water bodies and damsr1-31_ The movement of strata and surface caused by mining had disturbed various aspects of industrial and agriculture productions in the mining arear41. The earth dam is a very important water retaining structures, so it must makes sure the safety of dam if mining under it. Therefore, to study the effect of mining on dam and control measures to ensure safety of mining under the dam are important factors for improving the mining recovery ratio, reliving the mining continuity, preventing or reducing damage to the dam.By means of the harmonic mining technologyrs1, theoretical analysis and field observation, the mining method under an earth dam and the mining influences were studied and analyzed in this paper. The mining of a thick coal seam under the dam was carried out safely and successfully."

Jan 1, 2016

By Chase K. Barnard, Rahul Thareja, Sean Warren, Rajagopala Kallu

"Inflatable rock bolts are commonly utilized for ground support in Nevada underground mines, however, there is limited information regarding what factors influence the bond strength of these bolts. Bond strength is an important parameter in friction bolt support design, and this information is usually not available from manufacturers as a standard. Previous research has investigated the bond strength of friction bolts; however, these studies focused primarily on split set bolts and ground conditions more favorable compared to those commonly encountered in Nevada underground mines. Without site-specific bolt pull-out tests, ground control engineers are required to make assumptions regarding the in-situ bond strength of rock bolts. This is especially a concern for projects in the feasibility and initial development stages before site-specific experience is acquired.The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the Rock Mass Rating (RMR) system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively correlated with RMR, however the correlation is not strong. Cumulative percent graphs indicate that 97% of pull-out tests result in a minimum bond strength of 1 ton/ft and ½ ton/ft in RMR =45 and <45, respectively.Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed."

Jan 1, 2015

By John Stankus

Regional high horizontal stress has long been recognized as an important factor affecting roof stability However, localized high horizontal stress, although causing many ground control problems, has not received due attention, Through many ground control studies and underground experiences, it has been round that localized horizontal stress can be created by abrupt changes of overburden and stream valleys. The magnitude of localized horizontal stress depends on the valley configuration and overburden depth. Utilizing the Jennmar Finite Element Analysis System (JFEA), this paper analyzes the mechanism of the localized horizontal stress concentration based on two cast studies.

Jan 1, 1999

By Taghi Sherizadeh, Pinnaduwa H. S. W. Kulatilake

"This paper examines the effect of different geological and mining factors on roof stability in underground coal mines by combining the field observations, laboratory testing, and numerical modeling. Observations at an underground coal mine that uses the room-and-pillar mining method showed several failures of the immediate roof, and is used as a case study. Three-dimensional distinct element analyses were performed to study the intrinsic roof failure mechanisms and to evaluate specifically the effect of in-situ stress magnitudes and directions, discontinuity mechanical properties, and variation of pillar to room size on roof stability.INTRODUCTIONThe lithology of the immediate roof with respect to the underground openings plays an important role in stability of the roof in underground excavations. Laminated, or thinly bedded shale, is one of the most frequently seen overlaying strata above the coal deposits. The bedding planes and interfaces have very low or close to zero tensile strength in the direction perpendicular to the bedding planes, and their shear strength is much lower than of the rock layers. As a result, the bedding planes are much weaker than the rock layers. Therefore, due to the stress concentrations caused by excavations, slippage and separation can easily happen along the bedding planes before initiation of failure within the rock layers.In the past, several attempts have been made to understand the mechanism behind the roof failure in underground coal mines. Most of these earlier attempts were based on empirical techniques and continuum based numerical methods that have limited capability in simulating the response of discontinuum rock mass behavior to excavation. Different factors such as the magnitude and direction of the horizontal in-situ stresses, type and mechanical properties of roof rock, surface topography, geological anomalies, gas pressure, slippage and separation of bedding planes at the roof and floor, entry width and excavation sequences are identified as key factors that could significantly impact the stability of the roof. Among all the aforementioned factors, in spite of its importance, the impact of slip and separation of bedding planes on roof stability has not received enough attention from researchers. In a few available numerical modeling studies, the bedding planes are modeled using the continuum based numerical codes such as ABAQUS (Chen, 1999) and FLAC3D (Ray, 2009). However, since the bedding planes among the roof layers become discontinuous during the numerical analysis, this behavior is most likely not be accurately captured by the continuum based numerical models. Chen (1999) conducted finite element analysis to study the impacts of the roof and coal interface slip and the bedding planes slip in the roof on the stress distribution in the roof strata by using the finite element analysis software named ABAQUS. To avoid the complications associated with the finite sliding between two deformable bodies, he limited his study to the two-dimensional finite element analysis (plane strain). He concluded that the slip and separation of interfaces and bedding planes have significant impact on the behavior of the roof strata and without considering the interfaces, the roof bolt functions cannot be simulated properly by using the numerical analysis methods. Gadde and Peng (2005) performed three-dimensional finite difference analysis using FLAC3D software with strain softening material behavior to simulate the cutter roof in an underground coal mine. Their numerical model was fully continuum and no bedding plane was included in the model. They suggested that the strain softening material model can help to simulate the cutter roof failure up to a satisfactory level (Gadde and Peng, 2005))."

Jan 1, 2015

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By Christopher Newman, Zach Agioutantis, Gabriel S. Esterhuizen

"As conventional underground deposits are continuing to be depleted, mining operations have been forced to produce at greater depths and in more geologically and geometrically challenging conditions. Over the past decade, there has been a global increase in the application of cemented paste backfill (CPB) material as a means of ground support in open stope mining operations. Although CPB has been extensively used within the industry, there are many fundamental factors affecting the design of safe and economical fill structures that are still not well understood. A critical design issue with respect to backfilled stopes is determining the stress state within the fill material as well as the surrounding rock.This paper details the development of a reliable numerical model for the simulation of stress distributions around the excavated stope area, as well as through the backfill material. Through discussions on modeling parameters and output results, one is provided with insights into the mechanisms of stress redistribution allowing for further accuracies in simulating the behavior of the CPB material as well as its interaction with the surrounding rockmass.INTRODUCTION AND BACKGROUNDModern technological innovations with respect to material processing, cementitious composition and chemical additives, and material transportation have provided the mining industry with a ground support material that greatly reduces mine waste costs, while, when used appropriately, increases reserve production and mine stability. As mining operations continue to produce in more complex geologic and geometric conditions, cemented paste backfill (CPB) has become commonly employed within primary-secondary excavation-support sequencing allowing for total extraction of the mining reserve. As shown in Figure 1, primary stopes are initially excavated and then backfilled in a two-staged pour: plug and final pours. The plug (initial pour), is initially placed at the bottom of the stope with a CPB material of heightened cementitious material. While the plug provides a strong foundation on which to build the rest of the CPB structure, it also provides protection against barricade breakthroughs (Li and Aubertin, 2009), as well as providing operations a means of underhand stope-and-fill mining through the use of an artificial sill pillar (Hughes, et al., 2011). Following placement, the plug is allowed to cure to a designated design strength. Upon completion of the plug, a less cementitious “final” pour material is used to backfill the rest of the excavated area."

Jan 1, 2018

By William J. Conrad, Ryan J. Molka, Erik C. Westman

"In order to study pillar and overburden response to retreat mining, a ground control program was conducted at a Central Appalachian mine. The program consisted of several monitoring methods including a seismic monitoring system, borehole pressure cells in the pillars, and time-lapse photogrammetry of the pillar ribs. Two parallel geophone arrays were installed, one on each side of the panel with the sensors mounted 3m (IO ft) into the roof. A total of fourteen geophones recorded more than 5,000 events during the panel retreat. A MIDAS datalogger was used to record pressure from borehole pressure cells (BPCs) located in two adjacent pillars that were not mined during retreat. A series of photographs were taken of the pillars that had the BPCs as the face approached so that deformation of the entire rib could be monitored using photogrammetry.Results showed that pillar stability and cave development were as expected. The BPCs showed an increase in loading when the face was 115 m (380 ft) inby and a clear onset of the forward abutment at 30 m (100 ft). The photogrammetry results displayed pillar deformation corresponding to the increased loading. The microseismic monitoring results showed the overburden caving inby the face, again as expected. The significance of these results lies in two points, I) we can quantify the safe manner in which this mine is conducting retreating operations, and 2) we can use volumetric technologies (photogrammetry and microseismic) to monitor entire volumes of the mine in addition to the traditional point-location geotechnical measurements (BPCs).INTRODUCTION AND BACKGROUNDExcavation of underground openings is a difficult job in a challenging environment. The rigor of the process is compounded by the lack of a method that allows quantification of changes within the rock mass as excavation progresses. Statistics kept by the Department of Labor, Mine Safety and Health Administration show that 16% of fatalities and lost time incidents in the underground mining industry are due to unexpected rock mass failure (MSHA, 2015). A recent example is the Crandall Canyon, Utah, coal mine accident caused by the vertical collapse of a longwall coal mine on August 6, 2007 (Dreger, Ford, Walter, 2008)."

Jan 1, 2016

By Nicole E. Evanek, Anthony T. Iannacchione

"Over the past 36 years, a great deal of information has been presented and discussed at the International Conference on Ground Control in Mining (ICGCM). The topic of surface subsidence engineering has resonated throughout each of the 36 conferences, producing 155 related papers. These papers have come from many countries. The major focus has been underground coal, especially longwall mining, but hard rock mining has also received attention. This impressive collection of reports presents a unique opportunity to reflect on the progress made towards understanding subsidence basin characteristics and developing methods to predict and mitigate its impact.In the initial meetings, the focus was on measuring subsidence and developing prediction methods. As understanding increased, predictive methods were developed and tested, especially in North America, China, Australia, Europe, and India. Efforts were made to understand how structures, aquifers, and surface waters were impacted by the formation of subsidence basins. As time progressed, the number of papers dropped slightly and became more focused on site-specific conditions. Most recently, advanced monitoring techniques have revealed new information, spurring a resurgence in research activity. Another recent focus has been on anomalous horizontal deformations occurring in sites with significant relief. Several reports from Australia and one from the US have brought this issue to light. In closing, all of these surface subsidence engineering papers have chronicled the maturing of this most important topic and, in the process, highlighted the importance of the ICGCM in the evolution of our current state of practice.INTRODUCTIONThe aim of this paper is to examine the role of ICGCM in 1) shaping our understanding of the mining induced subsidence phenomena, 2) developing tools to help predict its impact on the surface, and 3) evaluating controls to mitigate these impacts.This analysis involved the consideration of 155 papers available within the ICGCM conference proceedings and listed under the subsidence topic. Three of the papers where only available as abstracts and were not included in this analysis. Four other reports were focused on topics other than underground coal mining-induced subsidence issues and were also not included. It should also be noted that papers dealing with overburden behavior were not included in this analysis. As a result, 148 papers were reviewed and analyzed (Figure 1)."

Jan 1, 2018

By Michael Gauna, Christopher Mark

"For decades, pillar recovery accounted for a quarter of all roof fall fatalities in underground coal mines. Studies showed that a miner on a pillar recovery section was at least three times more likely to be killed by a roof fall than other coal miners. Since 2007, however, there has been just one fatal roof fall on a pillar line. This paper describes the process that resulted in this historic achievement. It covers both the key research findings and the ways in which those insights, beginning in the early 2000s, were implemented in mining practice.One key finding was that safe pillar recovery requires both global and local stability. Global stability is addressed primarily through proper pillar design, and became a major focus after the 2007 Crandall Canyon mine disaster. But the most significant improvements resulted from detailed studies that showed that local stability, defined as roof control in the immediate work area, could be achieved with three interventions:• Leaving an engineered final stump, rather than extracting the entire pillar;• Enhancing roof bolt support, particularly in intersections, and• Increasing the use of Mobile Roof Supports (MRS)A final component was an emphasis on better management of pillar recovery operations. This included a focus on worker positioning, as well as on the pillar and lift sequences, MRS operations, and hazard identification. As retreat mines have incorporated these elements into their Roof Control Plans, it has become clear that pillar recovery is not ""inherently unsafe.""The paper concludes with a discussion of the challenges that remain, including the problems of rib falls and coal bursts.INTRODUCTIONPillar recovery has always been an integral part of underground coal mining in the US. When room-and-pillar methods are employed, large blocks of coal in the form of pillars are initially left in place to support the weight of the overburden. Unless these pillars are subsequently recovered, the coal they contain will never be mined."

Jan 1, 2016

By Soheil Bahrampour

Void detection and identification of bed separation while drilling holes in rocks for roof bolting can be a great source of information for the evaluation of ground conditions and adjustment of ground control or support measures. This can be accomplished through the monitoring and analysis of drilling parameters by the roof bolter. This paper reviews work currently under way in a joint study between Penn State University and J. H. Fletcher & Co. The detection of voids, along with identification of rock types, can lead to development of 3D roof maps, which can subsequently be used to evaluate ground support and its suitability for given ground conditions in tunneling and mining operations. Existing algorithms for void detection utilize the sensory information of the drill unit, such as feed and rotary pressure, revolutions per minute (RPM), and penetration rate, to detect voids or joints on the roof/ ribs. While the void detection algorithms are being revised to allow analysis of available data from the existing sensory systems of the roofbolters with higher accuracy and lower number of false detections, additional sensors have been added to the drill to improve its ability for accurate detection of the voids and joints. This includes installation of vibration and acoustic sensors on a drilling unit at J. H. Fletcher & Co., and pertinent data analysis which are discussed in this paper. Initial results indicate that the data obtained by vibration and acoustic sensors at high sampling rates can be used to improve the performance of the void detection algorithms independently, and when combined with the modified algorithms using existing sensors, it can substantially improve the capabilities of current void detection system.

Jan 1, 2013

By S. Mehrdad Heidari

The concentrator plant is located near a very high (105m), large (- 500m) and steep (a, > 45&apos; ) wall. Geologically, the wall was composed of very complicated formations and broad range of soils and rocks type in which a variety of local typical failures models have been occurred on different soil and rocks formations. The construction of concentrator plant structure and other activities have been overshadowed by these local failures. Safety and risk of huge failures were serious concern. For distinguishing the wall conditions a broad campaign of slope stability investigation with detailed geotechnical drilling on berms of wall have been done and the structure of slope was fully identified and further Lab tests and slope simulation models done. Slope stability of the wall was analyzed and the effects of instability factors were described in short term (for construction phase) and long term (for production phase).The results indicated, if a well-appointed drainage system is implemented, the overall stability of the wall in short term will not cause any particular problem but about long term stability, the wall must be supported by rock bolting, consolidation grouting, shotcrete reinforced with fibers. The results have been confirmed by passing one year after this investigation.

Jan 1, 2005

By Uros Bajzelj

When driving mine roadways in the vicinity of tectonic disturbances and fault zones, sudden outbursts of gas, along with ejections of fine coal, occur. Substantial dynamic changes occur around the roadways in the coal and around the support. The problem has several aspects. Studies have been carried out on the technical analyses of the phenomena which occurred in the Velenje Lignite Mine from 1957 to 1988, The second part of the investigation involves systematic laboratory studies of strength and deformability characteristics of lignite samples and "in-situ" measurements of stress changes during the driving of some roadways. Analyses of events (using the model of limit convergence and the finite element method) showed the possibility of gas outbursts, taking into account the deformability conditions when crossing over from compact lignite to the disturbed region. The rate of advance of roadways and the method of support strongly influence the occurrence of the phenomenon. The preventative measures used in driving roadways under such conditions include trial drilling and the use of blasting instead of machine cutting.

Jan 1, 1992

By Herryal Z. Anwar

In recent years, many both mining and civil engineering projects are developed in the area which may be categorized unstable, such as fractured and jointed rocks or "water sensitive rocks". For example, in underground coal mining, in which the floor strata normally consist of weak shale, the problem that may arise in roadway is floor heaving. In this case cement injection in borehole appears to be an economically effective method in order to make roadway more stable. This method may be also applied in the projects in which the constructions are laid on fractured and jointed rock. Nevertheless, the successful cement injection is much dependent on the water-cement ratio and the injection technique. This paper discusses the application of cement grouting to improve the ground stability in longwall mining, the laboratory experimentation of cement grouting and the method of floor injection.

Jan 1, 2000