Search Documents

By Paul H. Johnson

Chemical mining may be defined as the in-place extraction of metal values from ores located within the confines of a mine (that is, broken or fractured ore, stope fill, caved material, or ores in permeable zones) or ores located in dumps, prepared ore heaps, or tailing ponds. The term solution mining has, in general, been used to mean the in-place dissolution of water-soluble mineral salts with leach solutions. Chemical mining is presently in its embryonic stage. Basic research needs to be done to understand the influence of physical and chemical factors in chemical mining, and applied research needs to be done on both a small and a large scale to develop practical techniques of field practice. The areas of research include the following: (1) Leaching chemistry, the influence of physical, chemical, and biological factors in in-place leaching (2) Hydrodynamics of chemical mining systems (3) The development of new, as well as old, leaching agents for use under chemical mining leach conditions (4) The development of new means of contacting fine and coarse materials (with solutions) under static leach conditions (5) The development of new processes for generating and regenerating chemical mining leach solutions (6) The development of metal recovery processes

Jan 1, 1969

By J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is n practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota (a) must be covered with about 70 cm of soil material to achieve maximum production; (b) topsoil must be segregated and spread separately from subsoil; (c) potential production depends on the quality of the soil material returned; and (d) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation. Almost half the nation's cool reserves are in the Northern Great Plains underlying several million hectares of agricultural land. Social pressures to return mined land to agriculture or other productive uses have resulted in recent enactment of state and federal legislation, which is intended to restore productivity to disturbed areas. All such legislation relating to the Northern Great Plains has stipulated that useable soil material be saved and returned to mined land after spoils are smoothed. This requirement immediately raises questions as to how much soil material is needed, what criteria are important in defining useable soil material, how is the soil material to be handled in the earth-moving operations involved, and how can replaced soil material be maintained and revegetation. Scientists at the USDA Northern Great Plains Research Center at Mandan, North Dakota have conducted research on the reclamation of disturbed lands since 1970. Initially this research was designed to identify and characterize those physical and chemical properties of spoils that are most restrictive to plant growth (1). Basically, they found that any properties of spoils that reduced the efficiency of storage and utilization of the limited precipitation received adversely affected plant growth. Thus, in the Northern Plains, revegetation of mined land was found to depend upon the management of factors affecting the availability of water to plants - the same as on unmined land. After the major problems in revegetation were identified, technologies were developed to circumvent the effects of the growth-limiting factors (2). Basically two approaches were identified by which plant growth-restricting properties of spoils could be corrected: (a) various amendments (gypsum, sulfur, Fertilizers, mulches, calcium chloride, etc.) could be applied to spoils to improve their ability to conserve precipitation and provide water for plant growth; or (b) undesirable spoils could be covered with suitable soil materials to reduce or alleviate adverse effects. The latter approach appeared to be more feasible in most instances And is the approach specified in current legislation. The remainder of this paper discusses research on the use of roil materials returned to spoils and summarizes the information obtained.

Jan 1, 1978

By J. R. England, W. J. Taylor

The Sudbury Basin is the scene of the mining operations of the Ontario Division of the International Nickel Company of Canada, Limited. Around the rim of the geological formation and within thirty miles of the City of Sudbury are located twelve operating mines and one open pit operated by the Company. The City, with a metropolitan population of some 100,000 lies 240 miles Northwest of Toronto. In addition, there is one mine in Northwestern Ontario, at Shebandowan, 700 miles Northwest of Sudbury. In 1973 these mines produced 16.5 million short tons of ore of which 14.9 million tons were from underground and the balance from open pit operations. Mining methods include blasthole, sublevel caving, induced caving, shrinkage, cut-and-fill and undercut-and-fill. Raise boring commenced at Inco in 1964 and is now applied at all mines in the Sudbury District (Figure 1). [ ]

Jan 1, 1974

By Terry Mattioli, Buck Bradshaw, Terry Fagg, Larry G. Nisle

Deposition of calcium carbonate scale on activated carbon in the Pinson Mining mill carbon column circuit was causing erratic gold recovery rate, long acid wash time, high carbon attrition and long strip times. Continuous addition of a blended antiscalant into the mill thickener overflow at 8 ppm reduced the average carbon acid wash weight loss from approximately 10% to < 2%. Cleaner carbon improved the gold loading rate in the mill column. The loading on Column I was increased to 175-225 oz/ton carbon from 125-150 oz/ton for a two-day carbon advance cycle. The higher loading capability has given Pinson more flexibility and better control of gold flow through their carbon adsorption, stripping and electrowin­ning processes. Preventing calcium carbonate build-up on activated carbon with this antiscalant reduced acid wash batch time. This enabled Pinson to acid wash and regenerate every batch of stripped carbon for all the adsorption circuits. Shorter strip times have also resulted from the lowering of the calcium carbonate scale level in the loaded carbon. Carbon consumption has been reduced and is now averaging 0.046 lb/ton ore for the first six months of 1990 compared to 0.072 and 0.083 lb/ton respectively in 1989 and 1988.

Jan 1, 1990

By G. Adel, J. M. Richardson

Mine-to-mill optimization is a holistic approach to the optimization of mining and processing operations. Developed at the Julius Kruttschnitt Mineral Research Centre, it attempts to minimize energy consumption through the optimization of the particle size reduction process. The approach involves sampling and modeling of blasting and processing, computer simulation to optimize the operation and develop alternatives, implementation of the most promising alternatives, and sampling to quantify energy savings. The primary objective of the present effort is to adapt mine-to-mill technology to the aggregates industry. This paper presents an update of work being conducted at quarries operated by the Luck Stone Corporation of Richmond, Virginia.

Jan 1, 2006

By M. Rieber

The recent history of the mercury market results almost entirely from U.S. Government actions. Its derived demand has been curtailed by U.S.E.P.A. mandates; its supply has been augmented by U.S.D.L.A. controlled stockpile releases. The resultant prices have altered its market structure, impacted mercury mining, refiners and recyclers, and affected international production and markets. From a marketplace product mercury is rapidly becoming a disposal problem. Other minerals may follow in its wake. This paper reviews developments in demand, particularly in relation to environmental constraints. Supply side impacts are considered. The impact of stockpiles, both as a market overhang and as a potential supply is reviewed. Government stockpile disposal activity is emphasized, but the size, estimated disposal rate, and quality of the private stockpiles are considered, as is the potential availability of additional material from shut-in mines.

Jan 1, 1995

By Sahendra Ram, Priyadarshi Onam, Abhishek Kumar Singh

A numerical simulation study is carried out for assessment of stability of coal pillars having dirt bands by varying its size and depths. Physico-mechanical properties of dirt bands including thickness and its position in pillar system are varied in the simulation study. Results of the simulation study are correlated with the available empirical approaches of pillar strength are validated with field observations. It is observed that the presence of weak dirt bands significantly influences the strength of pillar. An attempt is made to develop correction factor for the available empirical approaches, which are developed without considering the weak dirt bands in pillar system. The findings of the study will be helpful for suitable design of different size of coal pillars at different depths and stages of depillaring operations.

Feb 1, 2025

By J. Mark Richardson

Steady-state flowsheet simulators for mineral processing plants have evolved to a current high level of utility and accuracy. Reliable, general-purpose, semi-empirical models now exist in nearly all unit operations categories particularly in the areas of comminution and classification. .These models, installed as user-selectable functions within the integrated frame- work of flowsheet balance-solver software systems, can be strung together to represent any plant configuration. In addition, CAD-like graphics, data reconciliation and model parameterization functions have become standard features of the current generation of integrated plant simulators. These advances have given engineers the capability to investigate many different plant scenarios while requiring a minimum of actual plant testwork. This paper describes a methodology and an integrated software package which are being successfully applied in a number of operating plants worldwide to predict plant performance under changing conditions. Those conditions which can be changed include effect-of ore type, feed size, water addition rates, equipment geometries and flowsheet modifications. By using data from actual plant optimization exercises in real mills, the paper illustrates and out- lines a technique which includes plant data collection, ore breakage testing, flowsheet simulation, model-fitting (parameterization), data adjustment and model experimentation. Brief descriptions of some unit operations models, such as autogenous mills and cyclones, are provided as examples of the current state of such models. Ore breakage testing and its relation to certain models is also discussed. Computer- generated size-distribution graphs, along with tabular data generated by the simulator, round out the presentation and serve to demonstrate the real- ism and accuracy of the models. The paper concludes with a partial list of cases where this technology has been successfully applied.

Jan 1, 1992

By Luigi P. Gonano, John C. Sharp

The Drakensberg Pumped Storage Scheme in South Africa with an operating head of 500m is located in sedimentary rocks containing relatively weak argillaceous strata. The paper describes design and construction aspects of the high pressure concrete-lined tunnels, and the associated investigation techniques and construction controls.

Jan 1, 1983

The next 13 years gave me an education that anyone, then or now, would well envy. W.T. Reid had founded Belmont School along the lines of Groton and, as at Groton, he sent many graduates to Harvard. He obtained excellent teachers and maintained as strict a discipline as the independent nature of the western students would stand. With a beautiful location in an unspoiled little valley in the foot- hills of the Coast Range there was every chance for walks and expeditions. The years at Belmont were good ones. My closest friends were Harold Jordan and Lewis Hackett. Lewis was son of the military director at the school. With half a dozen other very young inmates we early won the sobriquet of "The Dirty Dozen." Sliding down a steep muddy hill on barrel staves helped us earn the name. An inherited shyness exaggerated my sensitivity at being a "teacher&apos;s boy" and this prevented a close association with the wilder western boys who made up most of the schoolmates. Trapping wildcats and coyotes in the brush-covered hills and taking long walks gave me plenty to do. I had grown too fast and when I went to college was 6 ft 3 in. tall and weighed only 145 lb-hardly a respectable bean pole. I was only two months past 16 when I left for Harvard. The long summer vacations were happy ones. Most of them were spent in the high mountains, and even when I was ten years old I could keep up with anyone on long steep climbs. I learned to handle a rowboat during our stays at Lakeside, a rustic resort at the south- east corner of Lake Tahoe that could then be reached only by the steamer that made a dally trip around the Lake. Several of the teachers at Belmont remained good friends as long as we were on the same side of the continent. The finest was C.H. Rieber, who taught mathematics at Belmont for the first few years we

Jan 1, 1976

INTRODUCTION Automatic controls are devices that assist operators by performing routine tasks faster and better than they could alone. Great strides have keen taken in the development of new processes and bigger machines to improve productivity, but these developments created the need for increased protection of machinery and labor. The new production-line techniques, or continuous processes developed, resulted in routine and, frequently, demoralizing jobs. The human race is not constituted mentally to perform routine operations. Devices were needed also to gather information automatically and perform routine functions. High-capacity plants incorporating large equipment

Jan 1, 1985

By F. Wolf, R. Ellmies

"Fluorspar is one of the most important industrial minerals. It has a wide range of applications, for example it is used in the steel and aluminum industry, and is also the raw material to produce hydrofluoric acid, Teflon or Gore-Tex. There are only a few major fluorspar mines worldwide, with China being the most important fluorspar producer (U.S. Geological Survey National Minerals Information Center, 2017). At Okorusu, Namibia, fluorspar has been mined with conventional open pit mining methods from 1955 until 2014 from a large scale metasomatic fluorspar deposit with seven identified orebodies. There are about 7 million tons of measured resources left with an average grade of 27.5 % CaF2. This paper is based at an MSc thesis at Technical University Freiberg and describes the design of an underground mine for the A and D orebodies with an annual production rate of 100,000 t acid-grade fluorspar product. By comparing different mining methods and adapting variants of access to the underground orebodies the paper will emphasize on the selection of a suitable mining technology, with a special focus on the economic considerations to decide about the most profitable operation. INTRODUCTION Mining holds an important part in the economy of Namibia. In 2016 11.1 % of the GDP was made through mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists an underground mining operation. The global annual production of fluorspar is approximately 6 to 7 million t (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu produced on average about 50.000 t annually in recent years (U.S. Geological Survey National Minerals In-formation Center, 2015). Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an open pit mine with four individual pits (A-D) since 1980. In 2014 the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village. The intent is to develop a concept for the further underground development of the mine. There are still about 7 million t of measured resources left in the deposit, with an average grade of 27.5 % CaF2. This study focusses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged."

Jan 1, 2018

By I. K. Kapageridis

Environmental management and planning requires the integration of large volumes of disparate information from many sources and the analysis of this information with efficient tools for assessment and evaluation. Effective methods of communication that allow interactive participation in the planning, assessment and decision-making processes are also very important. The VULCAN software package from Maptek (Pty) Ltd comprises a large number of 3D graphical tools within an interactive 3D interface called ENVISAGE. These tools are designed and developed to help engineers and scientists to identify and solve environmental problems. The combination of VULCAN 3D Software and the I-SiTE 3D Laser Imaging system leads to powerful solutions for environmental management. This paper presents the capabilities of this integrated system and its applications for environmental management.

Jan 1, 2002

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

1.1 INTRODUCTION When underground mining involves total extraction, it induces overburden strata movements. If not properly planned it causes surface subsidence and affects surface environmental conditions. Total extraction usually refers to longwall mining and room and pillar mining with pillar extraction. Surface subsidence has long been a subject of intensive research for scientists all over the world and considerable achievements have been obtained. However due to its difficulties and complicated nature, research into overburden movement has been thus far incomplete as compared to that into surface subsidence. Since surface subsidence is a manifestation of the results of overburden movement, the processes and mechanisms of overburden movement must be fully understood in order to establish the mathematical prediction models of surface subsidence. In this chapter the processes of overburden movement and its zones of movement in the overburden will be discussed. 1.2 PROCESSES OF OVERBURDEN MOVEMENT When total extraction is used, it produces a large void in the coal seam and disturbs the equilibrium conditions of the surrounding rock strata. The roof strata bend downward while the floor heaves. When the excavated area (or gob) expands to a sufficient size, the roof strata will cave. As a result, the overlying strata continue to bend and break until the piles of the fallen rock fragments are sufficiently high to support the overhanging strata. At this tie the overhanging strata no longer cave, but bend and rest on the underlying strata. Strata bending and subsidence develop upward until reaching the surface and forming a subsidence basin. The whole overburden strata and the surface subsidence basin will further go through a period of compaction and gradually become stabilized. Current knowledge regarding the process of overburden movement has been derived from several sources. One is the direct observation of the mined sections and their surfaces, another from field monitoring of strata movements in the overburden, and others from computer modeling and scale modeling in the laboratory. For example, Figs. 1.1 and 1.2 show the results of a borehole monitoring experiment (Borehole B-2) using the full profile borehole inclinometer and full profile borehole extensometer for lateral displacements and vertical subsidence, respectively (Conroy and Gyarmaty, 1983). The panel, 400 ft wide by 5000 ft long and 630 ft deep, was extracted from the Pittsburgh No. 8 seam which had an average thickness of 54 in. The face advanced from east to west. Curve A in Fig. 1.1 shows the inclination of the borehole when it was 45 ft ahead of the face at Position A (i.e., on the solid coal side). The total deviation of the borehole was 1/7000. The first shear movement occurred at 130 ft above the coal seam and appeared to have occurred along the bedding plane with large contrast of rock strata on both sides, i.e., sandstone vs. shale. When the face had passed the borehole 79 ft at Position B, the borehole deformed to assume a bow shape with a maximum deviation of 2.8 in. from the center line. Numerous shearing planes occurred and extended further upward. When the face had passed the borehole by 75 ft at position C, strata subsidence was measured. Fig. 1.2 shows that a strata separation as large as 4 ft occurred at 40 to 100 ft above the coal seam. Above this level, the strata subsided more uniformly with bedding separations within 1 to 2 in. Another example is the longwall mining with complete caving in the Soviet Union&apos;s Karaganda Coalfield (Kolebaeva, 1968). The coal seam was 6 ft thick and 154 ft deep. The immediate roof was the fine-grained sandstone interbedded with coarse-grained sandstone. Above this, there was sandy shale and shale. In order to monitor the process of overburden movement, 15 stations were established in a borehole (Fig. 1.3). The elevations of those stations were measured when the face was at various distances from the borehole. Fig. 1.3 shows the movement history of each station. For convenience of comparison, the movement history of each station was plotted on a common reference point as shown in Fig. 1.4. Clearly, the movements of strata from Station # 1 to #6 were nearly simultaneous, i.e., they behaved as a single unit. The strata from Station #7 to # 15 had differential separations, the maximum of which was 40 in. As the face passed by and moved away, strata separations in general reduced gradually. But strata separation between Stations #12 and #13 remained the same until the end of the monitoring period. The total bed separation between Station #7 and # 15 reached 11 in., approximately 18% of seam thickness, when the face was 132 ft beyond. Based on the above observations, the author developed a conceptual model of overburden movement due to underground longwall mining (Fig. 1.5). The above-mentioned two case studies illustrated that subsidence in the overburden strata propagates upward and subsidence velocity decreases from the bottom to the top. When the subsidence velocity at the surface reaches the maximum value, the subsidence velocity at the bottom portion of the overburden strata has decreased considerably and the strata have begun to compact. Bed separation occurs within a certain distance above the coal seam and reduces from the bottom to the top. When the face has moved away, bed separation reduces gradually, so that eventually some beds completely close and others partially close. Bed separation reaches the highest level when the subsidence velocity at the surface is at its maximum value. For instance in Fig. 1.4 surface subsidence velocity was maximum when the face was 38 to 44 ft past the point. At this time the total bed separation was maximum. Overall the strata directly above the opening are subjected to tension in the vertical direction. But above a certain level, all strata move nearly simultaneously. There is also significant shear movement along some bedding planes. 1.3 ZONES OF MOVEMENT INTHEOVERBURDEN After the extraction of a longwall panel or room and pillar section of sufficient width the strata in the overburden are subjected to various degrees of movement from the bottom to the top. According to the movement characteristics, the damaged overburden can be divided into four zones (Fig. 1.6). Caved Zone. After the extraction of coal, the immediate roof caves irregularly and fills up the void. The strata in this zone not only lose their continuity completely, they also lose their stratified

Jan 1, 1992

By Steven J. Schatzel

A study was made of frictional ignitions in the underground coal mining industry from 1980 to 1992. The population of frictional ignitions was correlated to a variety of potential contributing factors including the mined coalbed, geographic location, mine production, methane gas emissions, and the type of mining equipment in use. The number of frictional ignitions reported in 1991 and 1992 surpassed the annual totals in all previous years included in the study. Most frictional ignitions occur during cutting operations at a coal face by a continuous miner. The average coal production of mines experiencing frictional ignitions is greater than the average of all underground coal mines throughout the survey period. Methane drainage may have produced a drop in the ratio of gas emissions to coal production (E/P) in mines experiencing frictional ignitions.

Jan 1, 1995

By O. Salami, G. Xu

Fire accident is one of the most classic safety concerns in underground mines both in the USA and abroad. It may occur from pool fires due to leakages in hose or pipes, vehicle fires, or fires in tires and conveyor belts in the underground mines. It may also result from the storage of flammable materials such as gasoline, diesel, and explosives in the underground. When fire occurs in an underground mine, it releases heat, smoke, and other toxic gases such as carbon monoxide, and methane to the surrounding thereby making life unbearable to the miners. Furthermore, smoke greatly impact visibility in the underground which makes evacuation even more onerous and challenging. To this end, a thorough investigation of fire behavior and spread of toxic gases in a practical underground mine is imperative to develop a reliable emergency evacuation plan in an event of fire disaster in the underground mine. The objective of this study is to investigate temperature variation and CO spread along mine airways by conducting full-scale fire experiment in the underground mine. The results presented from this study are crucial to developing evacuation plans in underground mines. In addition, the findings from this study could be used to validate existing evacuation models.

Mar 2, 2022

By Palmer C. Sweet

By-products from mining and processing plants and coal-fired power plants are being utilized more as valuable resources in Virginia. Mining-related by- products are divided into two categories: those generated from mineral extraction and beneficiation, and those generated from mineral processing or from industrial plants. Materials from both categories are produced in Virginia, where by-products have been exploited for various uses in the past and/or present. These materials include coal- combustion products (fly ash and bottom ash), lime-kiln dust, flue-gas-desulfurization residue, rock fines, magnetite, Cold Spring clay (kaolin), Austinville tailings, soapstone rock, and calcium-carbonate paste. Some of these by-products have never been utilized, although several ideas have been investigated over the years.

Jan 1, 1999

By V. T. McLemore

The Steeple Rock district in New Mexico is a major epithermal gold-silver district that exhibits district zoning. Five types of ore deposits occur within the district: •base-metal veins (with gold and silver) form the center of the district and occur along the Carlisle fault, •gold-silver veins along northwest-trending faults and outward from the base-metal veins, •copper-silver veins along the margins of the district, •fluorite veins along the margins of the district, and •manganese veins along the margins of the district. Areas of older acid-sulfate alteration occur throughout the district and also exhibit the following zoning: massive silica/chert zone (inner), silicified zone and clay zone (outer). This alteration overlies regional alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow, but older, epithermal hot-springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1996

By R. N. Rothan, V. Khunova, C. M. Liauw, G. C. Lees

The interphase modification activity of 1,3-phenylene dimaleimide (also known as m-phenylene bismaleimide (BMI)) has been studied in composites based on magnesium hydroxide (60% w/w) and a polypropylene block copolymer (PPBC) that featured an ethylene-rich elastomeric impact modifier phase. BMI was found to be a unique product that led to significant simultaneous improvements in composite strength and toughness, even at the high filler levels. BMI modification was found to promote encapsulation of filler particles with the elastomeric phase of the PPBC together with formation of a PP boundary layer of increased crystalline content.

Jan 1, 2003

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation was investigated as a process to convert gaseous CO2, into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results were achieved using heat-pretreated serpentine feed material and a high partial pressure of CO2 (Pc02). Specific conditions include 155°C, PC02 = 185 atm and 15% solids. Under these conditions, a 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy was utilized to investigate the appropriate feed characteristics, identify the process products and interpret the mineral dissolution and carbonate precipitation reaction paths. Key words: Mineral carbonation, Carbon dioxide sequestration, Carbonates

Jan 1, 2003