Search Documents

By Brian McInnes, Joseph A. Sopko, Behzad Khorshidi

"The Port Mann Main Water Supply Tunnel involves a 1km long tunnel beneath the Fraser River from Surrey to Coquitlam, BC. At depths of up to 60 m below ground, the earth pressure reached 6 bar. The tunnel is constructed using an EPB TBM and gasketed precast concrete segmental liner. The tunnel and two shafts were constructed in a variety of soil conditions ranging from soft to stiff clays and silts, to compact to very dense sands and gravels. After approximately 800m of mining, a very dense and highly variable soil group consisting of cobbles and boulders halted the TBM. Several options were considered to stabilize the TBM face so an intervention could be conducted. Although de-watering was considered, there was risk of settlement to the Port Mann bridge piers, which was within 500m of the tunnel. Hyperbarics were also considered, however, the cost, schedule and uncertainty of the work that needed to be done, made it a risky option. Ground freezing by Liquid Nitrogen was chosen as the best solution, which would provide a frozen block around the face of the TBM. A temporary platform on the river was designed and constructed to enable drilling and installation of the freezing pipes and temperature monitoring equipment. The operation required close coordination among the tunnelling, marine and freezing sectors. Following the intervention, the TBM successfully broke through the reception shaft, and the remaining project was completed. This paper describes the design, construction and operational approaches used for the freezing and serves as a basis for future projects requiring expedited ground freezing."

Jan 1, 2016

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982

The stability of mine roofs in permafrost zones is determined mainly by temperature and ice content. The deformation resulting from creep and temperature-dependent physical properties of frozen rock mass is the dominant component of total deformation. Roof bolts can consolidate the roof and control its deformation. In this paper, a finite-element model, for the analysis of the effects of roof bolting in a frozen rock mass is presented. The model includes the variables normally encountered when analyzing the effects of roof bolting in rocks. It also accounts for properties unique to frozen rock mass: creep deformation and the change in Young's modulus with changing temperature. The model shows that, as bolt spacing decreases, there is a trade-off between increased roof stability from increased mechanical support and decreased stability from increased conduction of heat into the frozen roof. This result was expected and shows that, for a given set of rock-mass conditions, including ice content, temperature, particle size, etc., there is an optimum bolt length and bolt density for minimum roof deflection.

Jan 1, 1997

By AJIT SWAIN, SUNATI MOHANTY

The abstract discusses the importance of predicting the dewatering performance of industrial hydrocyclones from laboratory models. It highlights the challenge of scaling up design and operating parameters for efficiency estimation. The paper describes experiments with a 2-inch and 4-inch hydrocyclone using silica sand. It details the development of a model using the Nageswararao hydrocyclone model and a simulator to estimate model parameters. The model is validated with experimental data, and a new model is developed using 4-inch hydrocyclone data. The technique is then extended to predict dimensions for a full-scale dewatering cyclone operating at higher throughput and solid concentration.

Mar 30, 2022

By M. Ghiani, R. Ciccu

After a short review of the basic concepts underlying the application of selective flotation and electrostatic separation to the beneficiation of phosphate ores, the paper deals with the results obtained with these two technologies for a number of run-of-mine ores of different origin and distinct mineropetrographic features. Problems are discussed in the light of the minero-petrographic characteristics of the ores.

Jan 1, 1993

By Walfrid Been

There are no particular nor unique features of iron mining that are not shared in some degree by all mining ventures everywhere. There are, however, at least three problems that have acquired a special emphasis from a unique cause. That cause is the embarrassment of riches under which the industry is suffering. The most obvious' feature of iron mining today is the copious abundance of usable ore and its almost universal distribution over the face of the earth. By the term "usable ore" is meant ore that is amenable to reduction by the usual and conventional processes. Amidst this plenty, three problems become acutely emphasized: 1. The geographic location that will provide a mine with the best market opportunity. 2. The size of the orebody that will be required to' return the preproduction investment. 3. The geometry and configuration of the orebody that will permit quality control measures to be effectively executed.

Jan 1, 1964

By P. Bottomley, M. Matthews

Maintaining an acceptable thermal environment in South African gold mines becomes increasingly difficult as mining progresses to greater depths where higher virgin rock temperatures are encountered. Current environmental practice offsets the resulting high heat loads by installing large refrigeration plants. However, with the continued escalation of refrigeration costs, it has become necessary to examine other methods for economically combatting the underground heat load. The Chamber of Mines Research Organization has recently been pursuing a programme to devise methods of reducing the flow of heat into underground workings at source. Although there are several sources of heat (such as machinery, men, and explosives), the most significant is that from the rock mass surrounding the workings (Bluhm et al., 1986a). The main thrust of the work has therefore been directed at predicting and devising methods of reducing this heat source. A great deal of theoretical work has been carried out on the prediction of underground heat flow. From a review of this work (Bluhm et al., 1986b) it became apparent that there are two major aspects which require attention, namely algorithms for predicting the heat flow around the advancing stope face, and a correlation of the theoretical work with accurate empirical data. In order to remedy this situation, new theoretical models have been developed (von Glehn and Bluhm, 1986), and heat flow measurements have been made in both a conventional stope (Bluhm et al, 1986a) and in a backfilled stope (Matthews u., 1987). A number of methods for reducing rock heat flow are being examined. These include the insulation of intake airways (Bottomley, 1985 ), backfilling with waste material of the worked out areas, and alternative approaches to the design of mining layouts, the mining method, and the choice of cooling strategy. This paper highlights the heat load reductions that can be achieved by backfilling the worked-out areas and by adopting concentrated mining. The first part of this paper summarizes the results of the measurements obtained in the conventional and backfilled stopes. The theoretical models are then described and comparisons are made with the measured values.

Jan 1, 1987

By Gregory A. Hope, Kym Watling, Matthew I. Jeffrey, Ronald Woods

Surface enhanced Raman Spectroscopy carried out in real time has been applied to identify surface species formed during gold leaching in chloride and thiosulfate media. Chloride ion is adsorbed prior to the gold dissolution potential, but its coverage is significantly diminished at the beginning of leaching. A gold chloride band is again observed when dissolution is rapid, together with bands characteristic of AuC14- ions in solution. With thiosulfate, a thin gold sulfide layer is formed slowly in the potential region where leaching occurs. At higher potentials, thiosulfate is oxidized to sulfur and sulfate, both products being identified by Raman spectroscopy.

Jan 1, 2005

By Nelson R. Shaffer

Glamorous, burgeoning biotechnology and mundane industrial minerals would at first glance seem to share little in common, but in truth, modern biotechnology depends on many minerals. Biotechnical processes also can be used in industrial mineral extraction and processing. Biotechnology is broadly defined as the application of biological organisms, systems, or processes to manufacturing and service industries. Genetic engineering has reinvigorated one of mankind's oldest sciences, biotechnology, into a booming business. Many modern processes depend on microorganisms cultivated under very stringent conditions in bioreactors. Minerals from carbonate, sulfate, chloride, nitrate, phosphate, and silicate families are used to provide essential nutrients and to regulate growth conditions (such as pH) in order to assure optimal growth of organisms. Certain cells or enzymes perform better when immobilized upon or within solids, and minerals are often used to immobilize cells, especially in continuous process. Minerals are also used extensively in separating and purifying products of biotechnology. Diatomite, zeolites, and silica are especially useful in purification processes. Industrial minerals also are commonly used to clean up large volumes of process water that must be treated. Biotechnology can be employed in exploration, extraction, and processing of geologic materials and in reducing mining or other environmental problems through bioremediation. Microbes have been shown to solubilize certain elements and so promote extraction of heavy metals, phosphate, aluminum, potassium, and even rare earth elements. In a related technique, unwanted materials such as pyrite impurities can be leached microbially to produce cleaner products in sand and clay industries. Microbial actions can modify surface characteristics and so enhance certain ceramic properties. Certain organisms can accumulate useful elements from dilute sources; others can transform unusable chemical species to more useful forms. Deterioration of stone, concrete, and even glass or brick, can be accelerated by microorganisms. Control of such biodeterioration could improve long-term performance of industrial mineral products. Microbial processes have shown promise in improving several mine-related problems. Certain bacteria help remove clays from phosphate slimes and other suspensions. Others are used to degrade cyanide or other organic chemicals such as floatation aids. Cells immobilized on clays have been especially efficacious in bioremediation. Biotechnology industries, like the industrial minerals industries, encompass huge ranges of materials and processes. Costs of products from these industries range from pennies to thousands of dollars per unit, and their products are vital for maintaining modern life styles. Many biotechnical processes depend upon industrial minerals and certain biological processes can be harnessed to do useful tasks in the minerals field. The interplay of industrial minerals and biotechnology is important today, and as biotechnology advances, its interaction with the industrial minerals industry can only increase.

Jan 1, 1995

By R. J. Sheets

In 2009 the Gold Quarry open pit mine, located 11 km northwest of Carlin, Nevada, USA, experienced multiple large-scale slope instabilities of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope instabilities occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower clay-rich sub-units of the Carlin Formation (Fm.). This deformation created preferential flow paths that allowed groundwater from the upper sandy sub-units to infiltrate low permeability clay-rich sub-units, thereby enhancing deformation of the slope toe which in turn destabilized the upper portion of the highwall. The outcome was a 160 m high slope instability that had a lateral run-out of 850 m. The effort to return the pit to ore production required both the geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This approach required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with blast induced, localized slope failures. Back-analyses applying numerical modeling indicated that the failure surface did not coincide with initial interpretations based on field observations; drilling results eventually confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the lower clay-rich sub-units. The outcome is a stable highwall within the Carlin Fm. following nearly ten years of repeated slope instability, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new open pit development.

Feb 23, 2014

By C. B. Cecil

The sulfur content of United States coal can be assessed by using a variety of approaches. The sulfur content may be expressed in terms of total sulfur in the coal, pounds of sulfur per million Btu, or sulfur remaining after reduction by coal preparation. In addition, the sulfur content may be applied to the demonstrated reserve base or to coal resource estimates. Unfortunately current data bases do not allow for an integrated assessment at the National level. Although classification of coal resources and reserves according to sulfur content is arbitrary, preferential production of low-sulfur reserves will positively skew the total sulfur of the remaining coal resource.

Jan 1, 1986

By R. Larry Grayson

A survey of 1250 surface and underground coal mines across the United States was made according to a stratified sampling technique based on national coal districts. A total of 171 responses (13.7% response rate) have been returned and summarized, giving a picture of computer usage in the coal industry. Overall, 63.5% of the respondents use computers, but the percent varied from 100% for large mines to only 44.1% for small mines. As expected, a proliferation of microcomputers has pervaded the industry. Importantly, in spite of the high usage of computers in the industry, sophisticated engineering applications have not yet burgeoned.

Jan 1, 1989

By F. Michael Wahl

With the exception of reports on commercial deposits of kaolin, fuller's earth, and other specialty type clays, there is little published information on the extent, properties, and potential uses of the clay resources of Florida. Recent studies by the Florida Bureau of Geology in cooperation with the University of Florida and the U.S. Bureau of Mines have proven the existence of two extensive Miocene clay deposits, one in peninsular Pinellas County and the other in southeastern Charlotte County. Drilling and subsequent testing of the clays from these deposits indicate their potential for economic development. Both deposits consist of montmorillonite type clays, have an average thickness of 25 to 35 feet, and are overlain by unconsolidated Pleistocene sediments. Preliminary firing tests indicate that the clays from Pinellas County are a potential raw material for lightweight aggregate production. The clay has good bloating characteristics across an acceptable temperature range with a resultant aggregate density of less than 1.00 specific gravity. The clays from Charlotte County have poorer natural bloating characteristics but might well be used after treatment or with additives. The economic potential and locations of both deposits emphasize the need for locating similar clay resources in the state that might have economic potential so that land use planning and subsequent urbanization will not prohibit their development.

Jan 1, 1972

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By K. A. Natarajan, J. M. Modak

A review of published literature on the biosorption of metals using nonliving biomass is presented. Factors such as pH, temperature, initial metal concentration, biomass loading, the presence of co-ions and the pretreatment of biomass influence the metal uptake by biomass. Although few generalizations are possible, unified theories regarding the mechanism of uptake are not available. Therefore, the above aspects of metal biosorption have to be defined individually for each biomass and metal-ion pair.

Jan 1, 1996

This paper presents the results of an experimental study undertaken to demonstrate the feasibility of using silica sand as a grinding media in stirred ball mills for ultra-fine coal grinding. Laboratory batch as well as bench scale continuous tests indicate that the use of silica sand can reduce the energy consumption by 50% and more over its steel media counter-part. Moreover, this approach has been found to eliminate the disadvantages observed with grinding using steel media such as high replacement cost, contamination of coal through media wear, greater degree of coal oxidation due to higher slurry temperature and greater level of noise dissipation. Additionally, coal-sand attrition system reduces the manpower time required which is often spent towards cleaning and storing of steel media in inert atmosphere to avoid rust and corrosion problems.

Jan 1, 1991

By Archie M. Richardson, Carl E. Brechtel, Tom R. Kelly, Frank Feero

Recent work to upgrade the ventilation system for the el Mochito lead/zinc mine in central Honduras is discussed. Network modeling and underground measurements were used to evaluate cost-effective alternatives for achieving satisfactory ventilation in a complex and expanding underground operation. Both interim and long-term solutions were implemented to make mining possible under difficult conditions. INTRODUCTION Mining operations at the el Mochito Mine, located in the central highlands of Honduras, Central America, have been virtually continuous since the opening of the mine in 1948. Initially a high-grade silver mine, the mine has expanded along a westward trend of pipe-like orebodies to a distance of roughly one mile from two centrally located shafts. Production of the relatively large San Juan orebody at the western most extension of the mine (Paddock, 1981) led to the introduction of diesel-powered equipment; however, the ventilation infrastructure was insufficient to meet the needs of mechanized mining. A succession of owners/operators in the 1980s allowed the existing ventilation infrastructure to decay to the point that ventilation in the production areas of the mine was very poor. Environmental conditions in some working areas were not conducive to efficient ore extraction because of high dry bulb temperature, high humidity, and diesel emissions. Upon acquiring the mine in 1990, Breakwater Resources of Tucson, Arizona began an aggressive program to refurbish the mine infrastructure to complete extraction of the San Juan orebody and to allow the extension of the mine another 2500 ft to the west for extraction of the Nacional orebody. The program included increasing the capacity of the main ventilation system. This article presents a case history of the process of upgrading the ventilation system in a mine where extensive old workings cause large air leakage. This process has been one of selecting solutions to difficult technical problems that are compatible with the existing mine infrastructure and economic constraints. The initial ventilation system is described in the background section, along with ventilation projections for the mine expansion. Field characterization of the ventilation system for design verification and fan specification is then discussed. The paper describes a series of interim changes to the system to improve ventilation pending completion of new ventilation boreholes. In addition, the temperature/ heat problems in the mine are described. BACKGROUND Initial Condition of Ventilation System The ventilation system is illustrated in Figure 1, which shows the extent of mining with the main ventilation paths superimposed. Early mining around the two shafts opened up vertical connections (stopes and raises) over the entire 2420 ft (737.6 m) of vertical extent, and mining progressed to the west primarily using compressed air and electric-powered equipment. Since ventilation was not a complex problem in the original mining system, the stopes and interconnecting raises were not sealed. The San Juan orebody was much larger than the silver ore zones mined previously, being primarily zinc and other base metals. Its geometry, size, and grade allowed the use of vertical crater retreat (VCR) stoping with diesel mucking and haulage equipment. Its depth, along with the existence of warm groundwater, resulted in a mine climate problem on the lower levels. To establish a complete ventilation circuit, two vertical boreholes (Bonanza Nos. 1 and 2) had been drilled by previous owners from the surface in the vicinity of the San Juan orebody. The system design called for air to be drawn down the intake shafts, across the lower mine levels to the San Juan workings, then up through the San Juan ramps and ore passes to these two exhaust boreholes (see Figure 1). In practice, however, only the Bonanza No. 1 borehole was drawing air through the desired path. Leakage across the old upper levels from the intake shafts, the Caliche tunnel, and from intervening abandoned stopes and raises supplied most of the air flowing to the base of the Bonanza No. 2 borehole. In effect, there were two ventilation circuits in semi-parallel through the mine, of which only one was delivering appreciable air to the San Juan workings.

Jan 1, 1993

By Bruce F. Bohor

Silica sand has been mined in Illinois from the St. Peter Sandstone since the turn of the century, especially in the area around Ottawa on the Illinois River in the north-central part of the state. Production of this sand, consumed mainly by the glass and foundry industries but also sought after for many other uses, has grown with the economy, and last year's output in Illinois exceeded 4,000,000 tons. Such an important commodity was given the early attention of the Illinois State Geological Survey, and a very complete report was issued in 1928, authored by J. E. Lamar. The mining and processing of the sand has changed very little during the intervening 40 years, so that much of Lamar's data and descriptions are applicable today. More recently, the stratigraphy of the St. Peter Sandstone in north-central Illinois has become better known from the work of Willman and Payne (1942). The present authors have borrowed generously from Lamar's publication, and we wish to acknowledge the contribution of both of these studies to our work.

Jan 1, 1969

The Peruvian mining industry has seen an explosion of foreign investment since President Albert? Fujimori's government was first elected in 1990. Since then, Peru has taken some large steps toward recovery, making it the envy of most other developing countries. A measure of political stability was gained in 1992 when Shining Path leader Abimael Guzman was captured. In addition, the country has taken on a huge privatization program, rewritten its foreign investment laws and has reined in its annual inflation rate from 1,700% in 1990 to about 8% by late 1997. Small wonder then that attendance at the XXIII Peruvian Institute of Mining Engineers conference reached a record level, many of whom are employed by some of the world's largest mining companies. About 2,700 mining industry professionals from all over the world attended the week-long event, held in late September in Arequipa. That was an increase from 1995s 1,600 attendees, that meeting also held in Arequipa.

Jan 1, 1998

By Cynthia S. A. Wallace, Joseph E. Crawford

The Culberson ore body is a bioepigenetic sulfur deposit located in the Delaware basin. Sulfur occurs in the Upper Permian Castile, Salado and Rustler Formations. Most of the ore body forms a subhorizontal layer within the Salado Formation. Abundant cave fill deposits of Rustler and younger lithologies occur within the Salado Formation and predate mineralization. The cave fill deposits provided porosity zones within the otherwise impermeable sulfate host rock and controlled sites of mineralization. A northeast trending fracture zone near the west edge of the ore body localized some deep mineralization and may have allowed migration of hydrocarbons from depth.

Jan 1, 1992